Search Documents

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

This paper describes a U.S. Bureau of Mines investigation of large-scale coal dust explosions in an experimental mine using a high speed electro pneumatic mechanism for the rapid grab-sampling of gases and dusts. This technique enables the monitoring of pyrolysis and charring in fuel dust particles, and the collection of gaseous combustion products, in both large and small-scale explosions. Data obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Test facility show the following: Rapid sampling appears to "freeze" the burned gas compositions at the flame temperature values. Gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen. The particles collected in the flame zone show signs of extensive pyrolysis and charring. Measurements of gas concentrations and particle flame temperatures suggest that char burning may have occurred in the flame zone.

By P. L. Placek

Correlations were made on experimental data for four New Mexico ore series to determine relationships between ore grade and uranium extraction during leaching operations. Such relationships provide information needed to predict the long-range supply of minerals to meet national economic and strategic needs. Results show that other ore constituents and gangue materials in addition to uranium grade influence uranium extraction. In general, tailing grades decrease and uranium extraction increases as both H2S04 and NaCl03 concentrations increase. Terminal emf and terminal pH also were studied. Similar trends appeared for all ores; however, specific combinations of results also were observed for individual ores and ore series. Experimental results indicate that uranium extractions are higher for lower uranium feed grades than predicted by other estimates. Three factors--uranium feed grade, H2SO4 concentration, and NaC103 concentration--were used to design factorial experiments for each ore series. Four additional feed assay factors--V205, Fe, C02, and CaO--were included in regression equations to account for some of the variation in data. The three factorial factors are represented in the regression equations by linear and exponential terms of the form D i'1*G i + Di,2 *e Di, 3*Gi. The four additional assay factors are represented by linear and squared terms of the form Di,*Gi + Di,2*eDi3*Gi. where the Di, ,J are coefficients, the Gi are factors, and the symbol * represents multiplication in computer notation. The interactions of the factors are represented by products of the nonlinear terms for all pairs of the factors.

Jan 1, 1981

By Jamie Girard Dwyer, Edward McHugh, Stanley Miller, Jeffrey Whyatt

This user's guide covers the operation of a suite of three computer programs-Bplane, Bstepp, and Bwedge. These programs can be used to evaluate the potential for plane shear, step-path, and wedge failures along the crest of a slope bench. Such failures reduce the width of a catch bench and may compromise the bench's ability to catch rolling or sliding material before it reaches miners working below. The Bplane and Bwedge programs address sliding of blocks defined by continuous planar joints. The Bstepp program examines sliding of blocks defined by more complex failure surfaces that include steeply dipping cross joints and may even include breaks across small bridges of intact rock. The programs are applicable to jointed rock masses where the joints are small relative to the overall slope and form a number of sets with uniform statistical characteristics within a slope sector. The theoretical basis, application, and operation of these programs are described.

Jan 3, 2007

By Charles L. Kimbell

In broadest overview, a substantial part of the world's mineral industry in 1990 registered small gains over its 1989 performance, but traditional statistical measures of mineral industry performance, namely global production, trade, and consumption levels, failed to mirror these gains. This was because of the sharp downturns in the mineral industry activity in the U.S.S.R. and the former centrally planned economy nations of eastern Europe. These downturns in this one geographic area had influences on almost all traditional statistical series, in some cases simply significantly reducing growth, in other cases providing for a global downturn, in almost all cases despite considerably brighter outlooks based on activities in other world areas. To be sure, the U.S.S.R. and eastern Europe were not the only places on the planet suffering problems of one type or another in 1990 that impacted on minerals industry activity, but with the acquisition of information presently available, it seemed almost assured that the difficulties of these economies in transition will be the most difficult of problems to resolve in the long run. It certainly appeared that the legacy of the half century or more of economic central planning will be a decade or more of very difficult adjustments, and a number of these will greatly affect not only the minerals industry of these transition countries, but also the rest of the globe's mineral industry as well.

Jan 1, 1993

By Robert F. Holub

The Bureau of Mines has evaluated four working-level radiation-measurement methods and optimized them from the inherent and statistical error standpoint. Optimization with respect to various sampling and measurement times yielded no marked improvement over the existing methods. However, when appropriate approximations are made and evaluated, these two-measurement methods can be reduced to simple formulas, eliminating a need to use nomograms. These modified methods also have improved inherent error characteristics. A new method--a combination of two existing methods--with improved inherent and statistical errors has been suggested. All the pertinent equations are given, together with the computer program, so that any two-measurement method can be readily evaluated.

Jan 1, 1980

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By Robert L. Lagace, N. Albert Moussa

The objective of this project was to perform a preliminary study to determine the desirability/practicality of burying the communication cables in underground mines in order to protect then from the effects of fires and explosions We conducted discussions with Government and industry specialists on the physics of mine fires and explosions, mine disaster fighting, rescue, and investigation activities, and on nine operations. In addition we examined published experimental work and selected detailed NSHA accident reports on fires and explosions in underground mines. We found the overall desirability /practicality of cable burial must be regarded at this time as highly questionable, because of its benefit limitations to special sceneries, its practical operational shortcomings, and the availability of alternative cable protection options.

Jan 2, 1982

By H. E. Blake

An evaluation was made to determine the economics of utilizing waste fluosilicic acid for production of (1) calcium fluoride, and (2) anhydrous hydro-gen fluoride. Two versions of each process were considered and compared. The evaluation showed that both products could be produced and marketed competitively. Lowest estimated product sales prices required to yield a 25-percent return on investment before taxes (discounted cash flow basis) was $339.34 per ton of hydrogen fluoride and $48.64 per ton of calcium fluoride.

Jan 1, 1971

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the comparative effectiveness of three wet dust control techniques for face drilling. Previous attempts to achieve effective dust control on face drills with dry collectors have not met with success, the largest problem being sustained effective dust capture at the face. Results show that (1) foam-through-the-drill can provide 95-pct average total dust reduction in gypsum; (2) water mist-through-the-drill can provide approximately 91-pct average total dust reduction and 93-pet average respirable dust reduction in salt; (3) external boom-mounted water sprays can provide approximately 50-pet average dust reduction for both total and respirable dust in salt. The investigation showed that (1) foam and water in small quantities are very effective dust control techniques for face drills when applied through the drill steel at the point of dust generation, and (2) boom-mounted water sprays are only minimally effective for dust control on face drills.

Jan 1, 1981

The title of this book, The Phoenix of Natural Disasters: Community Resilience is aptly chosen. ?The Phoenix is a mythical bird that never dies; the phoenix flies far ahead to the front, always scanning the landscape and distant space. It represents our capacity for vision, for collecting sensory information about our environment and the events unfolding within it.? (source: The Feng Shui Handbook, feng shui Master Lam Kam Chuen.) There are Chinese, Japanese, Russian, Egyptian, and Native American counterparts of the phoenix. All of these birds are identified with the sun and depicted as rising from the ashes ? living again. This is the essence of a community after a natural disaster ? they live again. The Phoenix of Natural Disasters: Community Resilience is edited by Kathryn Gow and Douglas Paton who have done an excellent job of creating a relatively seamless transition between chapters with different authors. The content is organized well with the first chapter providing an excellent overview of what is to come and each chapter including an abstract clarifying the focus of the chapter.

Jan 1, 2009

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

By Ronald D. Hill, Elmore C. Grim

Some of the terms defined here are not used in the text. However, the terms will be useful to those interested in this and other publications in the field of coal surface mining.

Jan 1, 1974

By M. M. Fine

A satisfactory mean: of beneficiating a Brazilian phosphate rock was developed in a mineral-dressing-research study by the Bureau of Mines. High-grade concentrates well ever the specified minimum grade of 70 percent tricalcium phosphate, were produced, with goad recoveries by agglomerate tabling and flotation. A lower gads but usable secondary product was recovered by sedimentation of the minus-200-mesh fraction of the ore. The ore wan representative of an extensive deposit recently discovered near Recife in the State of Pernambuco, Brazil, which will be exploited in a plant planned to eventually produce at the rate of 500,000 tons of concentrate annually. Although Brazil has been reported to Lave a substantial reserve of phosphate rock,3/ the country has never been more than a small producer of this commodity. From 1945 to 1950 the highest production of phosphate rock attained in Brazil amounted to 10,421 tons. Production in 1949, the most recent year for which figures are available, was 4,553 tons.4/

Jan 1, 1954

By Martin Hertzberg

The Bureau of Mines 8-liter flammability system was used to study the effectiveness of a variety of powdered inhibitors in preventing the propagation of explosions of coal dust or methane in air. Over 35 different chemical additives were evaluated against Pittsburgh seam pulverized coal. The least effective inhibitors were the carbonates, which required mass additions in the range of two to three parts inhibitor to one part of coal dust in order to prevent propagation. The most effective inhibitors were the derivatives of ammonium phosphate, which were effective quenching agents at additions of only one part inhibitor to four parts of coal dust. Alkali halide powders were of intermediate effectiveness. These laboratory-scale results are in good agreement with full-scale mine experiments in all cases where detailed comparisons have been made. Data were also obtained for the effectiveness of several of the same powdered inhibitors against methane-air explosions. Their relative order of effectiveness and the concentration ranges required for quenching the gas explosion are comparable to those measured for coal dust explosions. Data are also presented for the effectiveness of N2 and CF3Br addition. Some preliminary data are also presented for powder addition to methane burner flames. Those data are compared with other burner data and evaluated in terms of their relevance to explosion tests.

Jan 1, 1982

By C. P. Mangelsdorf

This report deals with the efforts to develop a portable device suitable for underground use for the purpose of measuring the frequency of vibration of the horizontal chords of Birmingham roof trusses. Four devices are investigated and evaluated. An approximate emperical expression developed from a mathematical analysis provides a means of converting the frequency into tension. The method appears to be effective in mines with shale roof but requires some modification for other roofs.

Jan 1, 1983

By Fun-Den Wang

A two-dimensional plane strain analysis by the stiffness matrix method was used to analyze two basic pit slope configurations. The magnitudes and the directions of stresses are given for a V-shape and for a flat-bottom pit with the slope angle varying from 30° to 90° at 10° intervals, Stress effects due to irregular pit configuration or to in-situ forces are discussed. Equations of similitude for gravity loading are given. Expressions are also given for the stresses at the toe as a function of slope angle. Procedures are given for finding the stresses in any geometrically similar pit slope of different dimensions and material properties from the stresses and equations presented in this report. Numerical results show that the V-shape pit slopes have lower stresses than the flat-bottom pit slopes; hence, they are inferred to be more stable.

Jan 1, 1970

By John P. Coughlin

Software techniques developed by the Bureau of Mines Denver Research Center for real-time microseismic data analysis are presented. These techniques focus on the simple acquisition of P-wave arrival times and their use in event location. The paper discusses in detail software techniques to separate microseismic events from mining noise such as drilling and from very large events such as rock bursts. Incorporation of these techniques has enhanced the reliability and accuracy of computer-based monitoring of microseismic activity in ongoing research by the Bureau.

Jan 1, 1982

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was toe valuate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of with standing explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972