Search Documents

By Roy Greenfield

During the detection phase, several procedures can be used to improve the signal-to-noise ratio (SIN) . • Subarrays of up to 10 seismometers should be used. The apparent failure to obtain improvement in SIN in the Westinghouse subarrav work is probably due to excessive noise in the electronics. The spacings needed for sensors in the subarray must still be established. • The sensors should be buried. Even burial to a few feet will probably give appreciable reduction of noise. A deeper burial will probably further reduce the noise; and, if the seismometers can be put below the weathered layer, the signal level will probably be increased. The reduction in noise by burial will be especially effective during high noise periods due to wind or rain. • Before attempting detection, the waveforms should be bandpass filtered. The bandpass should go from 25 Hz to an upper frequency of 100 to 200 Hz. Further measurements with a low noise system must be done before the signal-to-noise ratio can be determined for the 100 to 200 Hz range. Any narrow band noise should be removed by notch filters. • If noise levels differ among seismometers of a subarray, weights inversely proportional to the noise power should be applied to the seismometers. • Automatic methods of screening data for possible signal arrivals should be developed, but the final determination that the signal on a subarray output appears to be from a miner should be made by an analyst. Detection of "signal" on several subarrays should be required for positive identification. In the location phase, after detection: • If repeated signals are received, they should be coherently added (stacked) to give as good a SIN as possible for use in determining signal arrival times, to be used in location computations. The miner should, if possible, repeat the signal 25 to 50 times.

Jan 1, 1974

By Lauren Roberts, Lewis Martin, John Goris

The Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health (NIOSH) and Thiessen Team USA, Spokane, WA, have developed a pull claw that can be attached to any accessible friction bolt ring to test the performance (i.e., load-carrying capacity) of bolts without the use of a pull collar. This would allow true random testing of friction bolts, which need to be evaluated to determine if they are still providing an adequate level of support months or years after installation. Such support is critical to maintaining safe working conditions for underground miners.

Jan 1, 2004

By George S. Rice

"Soon after the armistice, an investigation was conducted by the writer on the use of liquid oxygen for explosive purposes in Germany, so far as the conditions of such investigation wore permitted at the time. The results of this inquiry were published in Technical Paper 243, entitled ""Development of Liquid Oxygen Explosives during the War.""Recently, through the courtesy of Dr. C. L. Parsons, former chief chemist of the Bureau, who was visiting Germany, and Mr. Chester L. Benson, of the American Expeditionary Forces in Germany, data was obtained from the Deutsche Oxhydric A. G., Surth near Cologne, (one of the principal manufacturers of liquid oxygen installation) concerning the number of plants which bad been installed in Germany during the period following the armistice. An analysis of the figures obtained shows the following installations in different kinds of mining operations:"

Sep 1, 1920

By Nicholas T. Zilka

One mineral deposit in the Golden Trout Wilderness has potential. The currently producing Pine Tree Mine on the Little Kern River has an estimated 120,000 tons (109,000 t) each of indicated and inferred reserves averaging 0.77 percent tungsten trioxide. No apparent potential exists for base or precious metal or other mineral deposits. INTRODUCTION The Golden Trout Wilderness, established by Congress in 1978 under Public Law 95-237, encompasses 240,000 acres (97,000 ha) of conifer-forested, rolling, upland plateau at the headwaters of the Kern River in Inyo and Sequoia National Forests (fig. 1). Abundant streams locally contain Golden Trout, namesake of the area. Major roads serve the area to the west and east of the Wilderness; access is poor to the north and south.

Jan 1, 1982

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By P. R. Bremner

The United States is more than 90 pct dependent on imported bauxite a source for aluminum, but it has vast nonbauxitic aluminum resources, such as kaolinite, anorthosite, alunite, etc. As part of a program to devise processes for treating these resources, the Bureau of Mines investigated a bench-scale leaching process using hydrochloric acid (HC1) and fluoride to extract aluminum from Wyoming anorthosite. HC1 and fluoride-to-aluminum (F/Al) mole ratios were studied with respect to aluminum extraction for single-stage, cocurrent, and countercurrent leaching modes. Using 95 pct stoichiometric HC1 and a F/Al mole ratio of 0.27, 90 pct of the aluminum was extracted by countercurrent leaching. Single-stage leaching with the same amount of acid and fluoride extracted 48 pct of the aluminum. Three fluoride sources, CaF2, Na2SiF6, and H2SiF6, were used and gave similar results on aluminum extractions.

Jan 1, 1982

Efficiently clear ice and frozen materials from ore-handling equipment. Approach Compressed air-propane torches that develop a high energy flame jet were used instead of ordinary propane torches. How it Works A high velocity high temperature stream of gases impinges on the ice and frozen materials to both melt and blast them away. This hot gas jet is at 3,000°F temperature and moving at 3,000 feet per second. In the photograph below, the jet is being used to clear frozen taconite from a grizzly. The functions of the compressed air-propane torch are as follows. The air heater assembly, which is mounted on a wand, con-

Jan 1, 1980

By Frank Pilotte

Proper design characteristics for a seismic system to locate miners during a mine disaster are considered in terms of a total system concept. Field hardware, processing equipment, operating personnel, deployment, training, and supportive R and D are necessary elements of the total system. Each of these elements is discussed and an indication given as to the requirements necessitated by each one. Hardware must be portable, rugged, and fieldworthy. Processing equipment must be simple to operate, expandable for future processing improvements, and ruggedized for field use. A small well-trained team must be available for quick response in times of emergency. Alternative deployment procedures are necessary to allow for a variety of situations including both ground and air delivery. Supportive R and D is used to support training and upgrading of the system.

Jan 1, 1974

By A. G. Kim

Coal formation begins in peat swamps or bogs, in which microorganisms alter plant material and initiate the formation of carbonaceous sediments. Methane, which constitutes about 98 percent of the hydrocarbon gas in coalbeds, is known to be a product of anaerobic microbial metabolism. To determine if other hydrocarbon gases could be produced in an environment similar to that of a swamp, samples of wood cellulose and lignin were inoculated with soil micro-organisms and incubated anaerobically. The resultant gases included methane, ethylene, propane, propylene, butanes, pentanes, and carbon dioxide. Hydrogen was also produced from the wood samples during the first month of incubation. Over 90 percent of the produced gas was methane; C02 was the other predominant component. Concentrations of all other hydrocarbon gases ranged from l to 20 parts per million, approximately 0.1 percent of the total hydrocarbons, which was less than the concentration in coalbeds. Therefore, although higher hydrocarbons could be produced in a swamp environment, subsequent mechanisms, either concentration by adsorption or formation during geochemical reactions, must affect the final concentration of higher hydrocarbons in coalbeds.

Jan 1, 1972

By Anthony Iannacchione

One of the more pressing engineering problems for deep longwall mines in the Southern Appalachian Basin is to design longwall systems that will eliminate catastrophic coal pillar failure from the working environment. The purpose of this study is to quantify the behavior of a particular size abutment pillar prone to burst or bump. Because the 24.4-111 (80-ft) square abutment study pillar is within the pillar size commonly used in this region, understanding the behavior of this pillar should aid in future efforts to design optimum mining strategies. This research has attempted to construct the pillar stress and roof-to-floor convergence profiles in order to evaluate the ultimate strength, deformation modulus, visco-elastic deformation, and violent failure characteristics of the pillar during longwall mining. This information reflects the overriding influence of the local geologic characteristics on bursts, provides the field measurements needed to verify concurrent modeling studies, and suggest some basic mechanisms associated with the coal pillar bursts discussed in this paper.

By D. B. Gawthrop

"In connection with the proposed use of Cordeau-Bickford to fire L.O.X. (liquid oxygen explosives) in well drill holes, the question has arisen as to the effect of very low temperatures on (1) the rate of detonation of Cordeau-Bickford; (2) the sensitiveness to detonation of its TNT filling; and (3) the lead covering of Cordeau-Bickford.The Cordeau-Bickford used in this investigation was the standard 6 mm. size, such as is regularly used in blasting, and was manufactured and furnished by the Ensign-Bickford Company, Simsbury, Conn. All pieces tested were taken from rolls, all of which were from the same melted batch of TNT in order that all the pieces tested might be as nearly identical as possible.Different portions of this Cordeau-Bickford were tested plain (not countered), countered, and double countered. The countering and double countering was carried out by the manufacturer prior to shipment.The determination of the temperature at the instant of making a test was accomplished by the use of a Leeds and Northrup potentiometer and copper constantan thermocouples. Each couple was made from No. 28 B & S gage wire with short junctions. One junction was inserted in a hole drilled by a No. 60 drill through one lead wall of the Cordeau-Bickford to approximately the opposite wall, so that this junction was in the center of the TNT filling while the other junction was immersed in ice water. The potentiometer readings in millivolts were converted to °C. from the calibration curve of the thermocouple wire,"

Jun 1, 1924

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

Promote safer and more efficient mine operations by providing communications between personnel located anywhere in the mine. Approach A radio communications system was designed which takes advantage of existing mine wiring such as telephone lines or electric power cables. The existing wiring distributes radio signals throughout the mine, making communications possible between roving miners, vehicle operators, dispatchers, and other personnel. How It Works Research has shown that medium frequency (MF) signals (300 KHZ-3 MHZ) can couple onto and re-radiate from nearby conductors. This effect is known as parasitic coupling and re-radiation. In a mine, these conductors include electric power cables, control lines, telephone lines, trolley lines, as well as metal water and air pipes Since all underground mines require these conductors for normal operations, the necessary network already exists and expands automatically as the mine is developed. A radio communication system has been developed that uses the parasitic coupling and re-radiation characteristic of MF. Using this system, whole mine radio coverage can be achieved without the need to install or maintain communication lines. The system consists of mobile transceivers for roving personnel and vehicles, and fixed-location base radio stations and repeaters.

Jan 1, 1982

Provide means for rapidly re-establishing ventilation control in metal mines after blasting, for emergency applications, and for routine temporary use. Approach Two quickly-installed, parachute-like stoppings have been developed and tested by the Bureau's Pittsburgh Mining and Safety Research Center. How the Parachute Stopping Works The parachute stopping can be fastened to an existing anchor point, opened, and effectively block the air flow, in less than two minutes. Because the parachute stopping tends to be self-scaling, its performance is generally better than that of conventional fabric stopping. However, the periphery of the parachute stopping must be longer than the periphery of the mine opening, Figure 1 shows the parachute stopping deployed in a mine entry. To reduce leakage during routine use, the cloth at the periphery of the parachute stopping can be adjusted and then anchored at several points as necessary. This extra adjustment can also be done after the initial installation during mine rescue or mine recovery.

Jan 1, 1977

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

By E. E. Remmenga

Often a collection of analytical data, which should reasonably be expected to follow the normal distribution, contains too many extreme values, which the experimenter is inclined to eliminate according to some arbitrary procedure. The stepwise computer procedure described for this purpose is similar to many other truncation procedures; however, because truncation of a basically normal distribution causes a downward bias in the estimated variance, this procedure provides a graphical method to compensate for the bias.

Jan 1, 1971

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919