Search Documents

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979

By C. W. Smith

Research was conducted by the Bureau of Mines to determine the effectiveness of various types of crushers for use with the Bureau-developed pneumatic concentration technique for mica. Three types of crushers were investigated in this study, a roll crusher, a jaw crusher, and a hammer mill. All the mica concentrates produced contained over 82 percent mica, but recoveries varied considerably. The roll crusher gave the lowest recovery of 46 percent of the mica followed by the jaw crusher with a recovery of 50 percent of the mica. The hammer mill proved the most effective, producing four concentrates with recoveries of at least 70 percent.

Jan 1, 1981

By S. J. Pearce

"INTRODUCTION AND SUMMARYComplaints have been made regarding dust respirators that may be used in coal-mining operations. Some of these complaints may be due to improper use of the respirator, inadequate knowledge of its purpose and mode of functioning, poor choice, poor fitting, or inadequate maintenance. It is hoped that this circular will answer these complaints by discussing the various factors relating to the proper use of dust respirators in general and in coal mines in particular.It is pointed out that dust respirators are not to be used as a substitute for dust-control measures. The construction, functioning, choice, fitting, and maintenance of dust respirators are discussed.FIELD OF USEThe function of the dust respirator is to prevent the wearer from inhaling harmful quantities of dust by removing dust from the air he inhales.A dust respirator is not to be used as a permanent substitute for dust-control measures. It is to be used as a temporary substitute until dust-control measures can be instituted or as a protective means where dust-control measures are impracticable, as in applying rock dust in bituminous-coal mines.The following sections of the ""Federal Mine Safety Code for Bituminous-Coal and Lignite Mines in the United States"" 2/ emphasize the fact that every effort should be made to keep the amount of dust in the air of the working places as small as possible:"

Mar 1, 1950

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

Great strides have been made in recent years to reduce the disaster potential of underground mine fires. However, mines can still be caught unprepared for a fire emergency. Fires can grow too large before they are detected, warning systems can be too slow and uncertain to reliably signal the danger, and suppression systems can be inadequate to extinguish the flames. New mining systems and equipment may create unanticipated fire hazards, and new materials may generate highly toxic combustion products. This report contains papers that summarize recent significant developments from the Bureau of Mines mine fire protection research program relating to these problems. Certain of these findings are also applicable to surface mining operations. The papers fall into the general categories of fire detection and instrumentation, fire warning, fire suppression, diesel equipment, spontaneous combustion, and toxicity analysis of combustion products.

Jan 1, 1988

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By Irven A. Jacobson

The thermal reactions of l-methylindole were studied in the temperature range of 525° to 627° C in a flow reactor. The major products consisted of 2-methylindole, 3-methylindole, indole, quinoline, hydrogen, and methane. 2-Methylindole is formed from 1-methylindole by an irreversible isomerization reaction. The 2-methylindole isomerizes in a reversible manner to 3-methyl-indole, the equilibrium favoring the 3-methyl isomer. Indole is formed directly from 1-methylindole. Quinoline is formed from l-methylindole, 2-methylindole, and 3-methylindole.

Jan 1, 1971

By J. C. White

A research study was conducted to devise a method for producing phosphoric acid directly from unbeneficiated Florida phosphate matrix. This research was performed as part of the Bureau of Mines, U.S. Department of the Interior, goals of improving minerals and metals recovery from domestic resources and of minimizing the environmental impact associated with mineral recovery operations. This report describes research in which unbeneficiated, dry, south-central Florida phosphate matrix was digested with sulfuric acid in a continuous-circuit, five-tank reactor to yield phosphoric acid and gypsum residue. Feed capacity of the reactor was 100 pounds (45 kg) of dry matrix per 24-hour day. When digestion was carried out at 185° F (85° C), acid filtration rates of up to 420 pounds of P20S per square foot per day were attained. Combined iron and aluminum impurities in the product filter acid were about 60 percent greater than values reported in commercially produced acid derived from concentrate. phosphate recovery was 87 to 90 percent of the phosphate contained in the as-mined matrix.

Jan 1, 1978

By Bill M. Stewart

The Bureau of Mines conducted laboratory tests to determine the effects on the physical properties of coarse coal waste of adding large amounts of fine coal waste. Maximum laboratory dry density, optimum moisture content, shear strength, and permeability tests were conducted on samples that contained 18 to 60 pct minus No.4 (U.S. Standard sieve size) coal waste. For the nonslaky materials, maximum laboratory densities were highest and permeabilities lowest when the samples contained between 30 and 40 pct minus No.4. Shear strength increased rapidly when the proportion of minus No. 4 was increased from 20 to 40 pct, but then increased only slightly or leveled off when the minus No. 4 was increased to 60 pct. Optimum moisture content and permeability were the physical properties most affected by the addition of fines. Optimum moisture content increased as much as 3 pct, and permeabilities decreased up to three orders of magnitude. Slaky coal waste material had physical property reactions to the addition of fines substantially different from those of nonslaky material.

Jan 1, 1981

By Paul S. Lewis

The Bureau of Mines hydrogenated coals of different rank that had been irradiated with either x-rays or gamma rays. Lignite, high-volatile A and C bituminous, and low-volatile bituminous coals were exposed to l billion roent¬gens of gamma-ray radiation; specimens of high-volatile A and C bituminous coals from other sources received 6 million roentgens of X-ray radiation. Irradiated and unirradiated control specimens of those coals were hydrogenated in autoclave experiments at (6,000-p.s.i. final pressure and 400° C. with retention times of 15, 30, or 60 minutes depending on the coal rank and catalytic treatment. Comparison of results from irradiated specimens with those from the control experiments showed that the radiation had no beneficial effect on the coal. High-volatile C bituminous coal may have been affected by radiation more than the other coals. One billion roentgens appeared to reduce the amount of coal converted to liquids and gases by about 10 pct., and 6 million roentgens reduced it by about 6 pct. then catalyzed with tin. In all other cases, the conversion of irradiated coal was either reduced by as much as 4 pct. or was essentially the sank as that obtained with unirradiated coal. Irradiation during hydrogenation nay be effective for increasing the reactivity of coal and should be investigated; further work with coals irradiated prier to hydrogenation is not recommended.

Jan 1, 1962

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muffling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the rod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By M. M. Fine

In an experimental study by the Bureau of Mines, in cooperation with National Lead Co., the roast-flotation process was found to be an effective means of upgrading certain cobalt-nickel stockpiles. The research was undertaken to determine whether the process could yield an enriched feed, with a minimum cobalt content of 6.0 percent, for the company refinery. The stockpiles (products of the company Fredericktown, Mo., milling operations) were essentially complex sulfides of cobalt, nickel, copper, lead, and iron, 1 sample of which contained 2.84 percent Co and 3.57 percent Ni. After a controlled oxidizing roast at 400° C., laboratory flotation with conventional sulfhydric reagents yielded an enriched concentrate analyzing 9.22 percent Co and 11.43 percent Ni, with recoveries of 84.9 and 85.8 percent, respectively. These are typical laboratory data; other data indicated higher grades were possible but at reduced recoveries. A brief, continuous campaign verified the applicability of the process to the raw material in question but was not continued long enough to establish optimum conditions. As a consequence, the results of the large-scale tests did not equal those obtained in the laboratory but definitely confirm the beneficiation possible from the roast-flotation process.

Jan 1, 1958

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

By Hal H. Engel

This publication was written in response to numerous requests for information about the Federal Bureau of Mines' "Demonstrated Lecture on Flame Propagation and Permissible and Explosion-Proof Electrical Equipment." The requests came principally from: (1) Persons wanting to know more about the demonstration before requesting it for groups they represented; (2) persons wishing advance information to help publicize a meeting where the demonstration was to be given; and (3) members of audiences desiring something to help them remember the salient points, facts, and figures presented during the lecture and demonstration. The purpose of the demonstration that accompanies the lecture is to show: (1) Variations in flame speed and pressure at various percentages of flammable gas within the flammable range; (2) effect of flame speed on the "pressure piling" within the area confining the mixture; and (3) the application of flame speed and pressure piling to the combustion of surrounding gas and to the design and maintenance of electrical equipment used in hazardous locations.

Jan 1, 1960

By A. E. Wells

"When the United States entered the World War, the heavy requirements for sulphuric acid in the manufacture of explosives made necessary a definite knowledge of the sulphuric acid capacity of the country. The Bureau of Mines, under the authority conferred by the explosives regulation act, made a thorough survey of the sulphuric acid situation. In this work, which was personally directed by the writer, comprehensive data were collected on the situation and capacities of the various acid plants, sources of supply of raw materials (brimstone, pyrite, pyrrohotite, zinc ores and concentrates, waste sulphur dioxide gases from copper smelting, and spent oxide from gas works), the principal points in regard to manufacturing processes (chamber and contact) and the uses of the acid. The results of this investigaion have recently been published by the Bureau of Mines, as Bulletin 184, entitled ""The Manufacture of Sulphuric Acid in the United States"" by A. E. Wells and D. E. Fogg. The following paragraphs on the uses of sulphuric acid are abstracted from this bulletin.Sulphuric acid is one of the most important of all chemicals, not only because of the large quantities manufactured but also because of the wide use of the acid in many different industrial works. Sulphuric acid is to the chemical industry what iron is to metallurgy. The general public, however, does not realize this fact, for sulphuric acid does not appear in the finished product as does iron and steel, but is only a means to an end. It is essential in many industries, such for example as in the manufacture of phosphate fertilizers, explosives, dyes and petroleum products. In recent years in the United States, especially in the East, the demand for sulphuric acid for chemical and metallurgical industries has been an accurate and sensitive barometer of the general business conditions. This demand for acid responds much more quickly to a general slump or boom in the industrial world than does the demand for iron and steel."

Oct 1, 1920

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954