Search Documents

By T. H. Dubaniewicz, J. E. Chilton

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 1992

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

By Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By M. J. Spendlove, P. P. Zapponi

"INTRODUCTION In carbothermic processes for the production of magnesium, magnesium oxide is reduced by carbon according to the following equation:(1) MgO + C = Mg(g) + CO.The reaction is virtually complete at temperatures above 2,000° C. but reverses rapidly at somewhat lower temperatures. To produce magnesium by this reaction, therefore, it is necessary to cool the gas very rapidly to a temperature at which the rate of the reverse reaction becomes negligible. Several media for quenching the gas have been proposed, among which are hydrogen, natural gas, liquid hydrocarbons, and molten metals of low melting point.The results of a preliminary investigation on the use of molten lead as the quenching medium are summarized in this report. The work was done in 1941, when the threat of war made it imperative to investigate every process that offered possibilities for rapid expansion of domestic production of magnesium. Although the results were encouraging, other processes appeared to offer better prospects for immediate wartime development, so the work was not continued. Shortly before the investigation was completed, several patents on the use of low-melting metals for absorption of magnesium vapors appeared, 4/"

Jun 1, 1947

By C. L. Severy

On the Pacific coast during World War II, a tremendous ship-building industry was developed, Early in the war it became impossible to obtain in- got or steel scrap for ship ballast. Magnetite, an oxide of iron, was sub- stituted as it fulfilled the requirements of weight for available space in the ships. Consequently, a new use for the western magnetite was rapidly developed.

Jan 1, 1948

By Oliver Bowles, J. E. Crawshow

A line of cordeau detonating fuse was placed in hole No. 2, no electric detonators being used in the hole. After 12 or 13 cases of 40 per cent nitro starch powder had been poured into the hole in loose form, it was found that a space of only 17 ft. remained for stemming. It was decided that space for an additional case of powder might be obtained by tamping the charge. The tamping was done with a heavy plunger, about 3 or 3 inches in diameter and 10 inches long, made of lead with an iron core with an iron eye in the top to which a 3/4 inch rope was attached, and weighing between 30 and 40 pounds. This weight was intended for use in sinking explosive in wet holes, and not for tamping. It is estimated that the tamping had continued at least 10 The quarry superintendent had gone a considerable distance for a box of powder, returned, and reached a point about 10 feet from the hole, minutes.

May 1, 1920

By Arcy P., D&apos Banister

Several gold-antimony geochemical anomalies were outlined near Stibnite, Idaho, using the humus sampling technique. Several hundred reconnaissance humus samples were collected and analyzed by a combination fire-assay atomic absorption method. The results partially outlined several gold-antimony anomalies and are very encouraging for further work in this part of Idaho.

Jan 1, 1970

Develop a safer, more effective, and more efficient method to control fires in abandoned coal mines and waste banks. Maintain the costs of this new method at less than or comparable to conventional AMI fire control methods. How It Works Cryogenic extinguishment of subsurface fires is a method of heat transfer. Bureau-designed injection equipment produces a pumpable slurry of liquid nitrogen and solid particles of carbon dioxide. Liquid or gaseous carbon dioxide from a pressurized tank flows to a bell-shaped nozzle where the change in pressure causes the carbon dioxide to form a granular snow. The solid carbon dioxide is mixed with liquid nitrogen. A jet pump is used to move the slurry through the delivery lines and into a simple injection probe. At injection, the nitrogen vaporizes and the carbon dioxide sublimes. This phase change produces a cold gas (-180° C) that, as it expands and moves in all directions, removes heat and also displaces oxygen. This combined process inhibits the combustion process and lowers the temperature below the reignition point. When the liquid nitrogen and solid carbon dioxide are converted to gases, the expanding gas acts like a piston, forcing warm air out of the porous bed, Although smoke and hot gases arc forced from the burning coal, generally there is no significant increase in the odor associated with burning coal.

Jan 1, 1992

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

By Oliver Bowles

It is noteworthy that 80 to 95 per cent of the gross production of all slate quarries in the United States is discarded as waste . In view of the loss involved in handling so much waste , and the consequent added cost of the finished product , the Bureau of Mines has undertaken a study of the slate industry for the purpose of devising the best means of reducing the proportion of waste , and of utilizing the unavoidable waste . The utilization of waste has received special attention , and the cooperation of many prospective purchasers of waste slate has been enlisted in testing its adaptability for various uses .

Mar 1, 1921

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982

Graduate education is an integral part of the Center's research program. The scope of. work and the duration of each research project is calculated, in part, by taking into consideration the needs of the graduate research program and graduate training. Full development of student involvement, as demonstrated by the research practicum which is offered to qualified senior undergraduates at Penn State University and is designed to acquaint them with research methods and techniques and inform them of the opportunities available in this field. and the fulfillment of graduate program requirements are of the utmost concern. The Pennsylvania State University and West Virginia University have accredited mining engineering curricula and rank among the schools with the largest enrollment in this area in the nation. The number of undergraduate students enrolled in mining engineering at Penn State and West Virginia University account for nearly 20%, of the total undergraduate enrollment in this discipline in schools across the United States. The Pennsylvania State University. West Virginia University, Massachusetts Institute of Technology, University of Minnesota, and Michigan Technological University, have granted a total of thirty-five (35) doctorate and masters degrees which can be directly attributed to research conducted in the Center.' Of these graduates, fifteen(15) have found employment in the mineral sector of the economy, i.e., in private industry, with government agencies, and at various universities, worldwide. In addition, a number of those graduating with masters degrees are currently pursuing a doctorate degree.

Aug 31, 1989

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By John C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high- temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

By J. F. Barkley

"A knowledge of the carbon dioxide (002) content of the products of combustion, particularly from the boiler furnace, is very valuable. An instantaneous indication of the CO2 can be used as a useful guide to efficient burning. A permanent record over a. period of time gives a story to the management which tends to keep the operators more alert. Many instruments that indicate and record CO2 have appeared within the last fifteen years. More are about to appear. Although simple principles involving chemical, physical, or electrical qualities, are being used, there is at present a general feeling of uncertainty about such instruments in the boiler room any instruments are bought, run awhile, then lie idle indefinitely.Inquiries as to CO2 machines continually come to the Bureau of Mines from the general public, as well as from other branches of the Government. Some ten years ago a series of tests was made on certain instruments at that time on the market. The following test was made quite recently on four of the newer types, including one using an electrical principle. The four instruments were installed on one boiler each, according to the instructions of the makers, and the recommended routine attention was given them. The test was of a service nature duplicating the conditions under which the instruments ordinarily serve. The boiler that was available for this purpose was practically banked for some hours of the night. This caused the average CO2 for the entire twenty-four hours to be rather low, although it reached the higher ranges of the instruments during the day.Each day the charts were averaged and the results plotted to form the accompanying curve. The record of each instrument is shown by its particular mark, the dot, circle, cross and square being used in addition there is plotted for each day a rectangular area representing 1 % CO2 in height. The proper positions of this area was determined by means of the Crsat. Where the plotted point for an instrument falls within the rectangel its accuracy is within 1/2% CO2, which is considered satisfactory. Where it falls outside the rectangle, inaccuracy is indicated."

Mar 1, 1925

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By F. C. Gregory

"The ""safety bonus"" in metal mining is a sum in addition to the regular wage, paid to foremen or bosses for keeping the accident rate down to a specified minimum. It has been used with success for some time by certain companies as a regular part of their safety work. It is desirable from the employer's point of view in that the desired results in accident reduction must be accomplished before the bonus is earned; and from the standpoint of the recipient, in that he receives a reward for the additional effort which he has put forth in order to earn the bonus.While this paper relates to the safety bonus as applied in the metal mining industry, the bonus system discussed herein will apply equal well to coal mining, oil-field work, and other mineral industries.Various estimates have been made as to the percentage of accidents that can be prevented through physical safeguards, adoption of safe working methods, and other safety measures which can be initiated and carried out wholly through the management or the safety department. This percentage will always be a vari¬able according to the local plant and conditions. But all who have been engaged in accident prevention agree that such work alone cannot bring the accident fre¬quency down to where it should be, and that it is very necessary to work directly with the workmen, in an effort to make each individual do his share in making the work safe. In this latter phase of the work, the boss who has immediate super¬vision of the men is the one who can do the most, since he is in daily and frequent contact with the men while they are at work. In the metal mines, the shift and stope bosses are the key men; in the oil fields, the ""tool-pushers"" or sub-foremen, and the same applies to all industries. So it becomes necessary to keep these sub-foremen constantly interested in accident prevention, both because they are in personal touch with the men and because they are responsible for production and hostile to any plan which they think will interfere with their output. In large organizations it is the shift boss who represents the company and its policies to the man on the job."

Jun 1, 1924

Objective: To improve the effectiveness of dust collector capture on surface mine drills.

Oct 1, 2005

Decrease the dust concentrations at the shearer and reduce downtime associated with spray system maintenance. Approach Increase the quantity and quality of the water supply on longwall faces by decreasing pressure losses, Increasing pump capacity, and installing a "non-clogging" filtration system. How It Works Water sprays and ventilation are two of the primary methods of dust control on longwall operations. Increasing the quantity and quality of the water supply to spray systems is one of the more effective and least costly dust control methods that operators have at their disposal, yet this method is largely ignored. Poorly positioned spray nozzles operating at low pressures (and flows) which plug frequently cannot be effective. Water supply system Improvements should be a fundamental part of all longwall dust control plans. Upgrading a water supply system may require one or more of the following improvements depending upon where a particular system may be deficient: Increasing pump capacity for additional flow and pressure; increasing line sizes to decrease pressure losses: and, decreasing maintenance downtime and Improving water quality by installing a "non-clogging" filtration system.

Jan 1, 1981

Roof bolting is a slow, expensive, and absolutely necessary mining activity. Roof-bolting activities also account for the largest percentage of lost-time injuries in underground coal mines. Dull bits result in the application of excessive force, which bends drill steel; and changing starter and finisher steel was the most significant source of injuries associated with roof bolting. The tungsten carbide (WC) roof-bolt drill bits currently used in American, Canadian, and Australian coal mines are capable of drilling only one or two 4-ft holes and then they are resharpened once or twice to drill another one or two holes. Often, in medium-hard rock formations (sandstone), as many as 20 to 30 bits may be required to drill a single 4-ft hole. Objective To compare the performance, longevity, and cost of newly developed polycrystalline diamond compact (PDC) roof-bolt drill bits against WC bits. Research and Background Diamonds for industrial use have been scarce throughout history and continuous attempts have been made to produce synthetic diamonds. The first synthetic diamonds were manufactured in 1953. Economically produced synthetic diamonds are 1 to 10 µm in size, but in this size range, they are totally unsuitable for industrial applications. In 1972, General Electric Co. developed a process to sinter the artificially developed, minuscule diamond particles into usable products. In this process, several layers of diamond-particles-and cobalt mixture are overlaid on WC substrates and sintered at 2,350° F and 1,000,000 psi. The final product is known as PDC. Today, PDC's are available in many shapes, but their size is limited to 3/4 in, or less, in length or diameter, because pressures greater than 1,000,000 psi are required to manufacture larger PDC's. At present, diamond and PDC arc the hardest and strongest commercial materials available for wear surfaces. The PDC used in this study had a hardness 3.61 times greater than that of WC.

Jan 1, 1992