Search Documents

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By Mark P. Meyer

During 1991 through 1993, the U.S. Bureau of Mines (Bureau) -Alaska Field Operations Center (AFOC) in cooperation with the Bureau of Land Management (BLM) -Arctic District Office and the State of Alaska, Division of Geological and Geophysical Surveys (ADGGS), conducted exploration, geological, geochemical, geophysical, mineral resource, and mineral potential investigations in the 6.7 million hectare Colville Mining District (CMD) study area. This mining district study area, located in northern Alaska, includes the Colville River drainage basin as well as 0.35 million hectares of the southern part of the National Petroleum Reserve in Alaska (NPRA). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district program. The Bureau's MLA mining district program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies.

Jan 1, 2011

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

By Joseph J. Wallace, William H. Tavenner, D. A. Reynolds, John M. Provost, James J. Dowd, R. F. Abemethy

"CONCLUSIONSThe investigation shows that there are 5 coal beds of major importance in Wyoming County from the standpoint of present production - Pocahontas No. 3, No. 2 Gas, Sewell, Beckley, and Eagle - and 5 beds of minor importance - Pocahontas No. 6, Cedar Grove, Winifrede, Douglas, and Chilton. The Pocahontas No. 3 bed contains the largest remaining known reserves.Known measured and indicated reserves in all beds, based on a minimum thick¬ness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,665 million short tons as of January 1, 1951. Of this total, 2,121 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Wyoming County, as determined by this investigation, is 55.0 percent. This percent¬age is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. The known recoverable reserves are estimated to be 1,167 million tons as of January 1, 1951.4. Since most of the Wyoming coals are medium- and low-volatile bituminous in rank and expand during carbonization in modern ovens, they are blended with high-volatile contracting coals."

Apr 1, 1953

By K. Thirumalai

The feasibility of breaking hard rock by thermal weakening and subsequent mechanical impacting was tested, Field tests at a basalt quarry in Dresser, Wis., demonstrated that large hard-rock blocks (5 by 5 by 5 ft) could be effectively reduced in size by this method. A series of secondary breakage tests, using air-propane heating, resulted in an average heating cost of $0.36 per ton. This combination energy approach provides an alternate means of size reduction of large hard-rock boulders for quarry and for underground are chute and grizzly operations where mechanical methods, used alone, are ineffective.

Jan 1, 1975

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage bf measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By Holt L. Farley

This report describes the development of an electronic system which detects unsafe slack and overload conditions in underground mine hoist ropes. The Slack and Overload Rope Protection System (SORPS) includes a fail-safe load cell inserted between the rope and the conveyance, and an accelerometer mounted on the conveyance. Signals from these transducers are telemetered via a radio link to the hoist control room, where they are combined with drum speed and chair status in a microprocessor-based decision and display unit. Abnormally high external force levels are detected as discrepancies between rope tension and cage acceleration; conveyance weight is inferred continuously. Hazardous conditions are displayed to the hoist operator, along with general hoist status. The system has been tested in a working mine for approximately two years. The report contains specifications, design data and field test experience generated under the SORPS program. It also includes information on dynamic modeling, vibration environment, the status of existing slack detection systems, and applicable control strategies.

Jan 1, 1983

By Paul M. Tyler

Graphite occurs in many places in the United States, but previous to 1914 the domestic production amounted to only 15 to 20 per cent of the natural graphite consumed in this country. Including artificial, graphite, the proportion was about 25 per cent. During the World War the production of both natural and artificial graphite increased until, in 1918 it, contributed more than one-half of the available supply, and since 1919 the proportion has not fallen below 40 per cent. Except during the war period, however, this apparently increasing independence has not been due to any large increase in production from domestic mines. It simply reflects a larger output of artificial graphite and reduced imports of Ceylon lung and chip, grades which have never been produced in substantial quantity in the United States. DOMESTIC DEPOSITS3 American graphite deposits, though numerous and often large, are characteristically low-grade. They constitute an abundant source of potential supply, but in normal times they have proved relatively costly to work, and even at the same price the various products have never been able wholly to displace certain imported qualities, notably crucible grades from Ceylon and pencil graphite from Mexico.

Jan 1, 1929

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control f anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/ These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the amounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating before a dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By Mark K. Larson

A constitutive model for rock interfaces based on the principles of static fatigue is proposed. The model is applicable to weak rock or joints with cohesion. Friction and dilation are decreased as plastic work increases. At equilibrium, the creep time increases by one time-step interval, and interface cohesion at each node decreases according to a power function. A constant-load, direct-shear simulation showed that the model is cap- able of mimicking constant-rate and tertiary creep and predicting failure. Tests on core from a coal mine showed constant-rate and, sometimes, tertiary creep, but also weak transitory creep. The cohesion deterioration function may need modification to simulate primary-phase creep. If model parameters are known for a site, the model can predict the onset of tertiary creep and failure. Such predictions can help engineers make better entry design and support decisions, which will reduce the likelihood of roof falls and increase safety for underground miners.

By William O. Vanderburg

This report3/ gives the results of a reconnaissance of mining districts in Eureka County, Nevada, made from September 25 to October 20 and from October 27 to November 5, 1577. During this time, virtually all the districts were visited and many data obtained on active and inactive properties. This report covers the locations of the various districts, geological background, ownership and brief descriptions of mines and prospects, information on past and current operations, and, other data likely to be useful to those interested in the development of our mineral resources. From the viewpoint of past production in the county, the silver-lead-gold deposits at Eureka have been tie most important, followed by the silver deposits at Cortez and Mineral Hill. The period of greatest activity in the foregoing districts was from 1870 to 1990, when Eureka was one of the principal mining areas in Nevada; the production of lead was sufficient to affect its price in all the commercial centers of the world. Eureka also merits the distinction of being the birthplace of the silver-lead smelting industry in the United States.

Jan 1, 1938

By Fremont F. Clarke

"INTRODUCTION Clay beds of southwestern North Dakota were investigated to determine (1) the average alumina content of the clays in four principal areas of occurrence, (2.) which, if any, would be the most feasible method of extracting alumina from the clays, and (3) whether the clays had any other commercial uses.During the investigation exposed sedimentary beds were examined for clay and the thickness and areal extent of outcropping clay beds in the more promising areas were measured. Four-principal areas of bentonitic clays, comprising 6,967 acres in Stark, Slope; and Billings Counties, N. Dak., were mapped and sampled.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our natural resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chiefs analyzes samples and makes beneficiation tests.Acknowledgment is duo John P. Gries, professor of geology, South Dakota School of Mines and Technology, for his studies of and advice on geological phases of the work. His data were drawn on freely in preparing this report; also E. D. Gardner, regional engineer, Rolla, Mo., and E. Y. Dougherty, district engineer, Rapid City, S. Dak., for assistance and advice in supervising the program."

Mar 1, 1948

By GEORGE S. POPE

This bulletin is the third of a series a showing the results of ment purchases of coal according to specifications as to its quality and giving typical forms of proposals for supplying coal and general information relating to government coal purchases . Numerous calls for authentic information concerning the purchase of coal according to its heat value attest a growing interest in the subject. Many of the commodities of life have long been purchased according to specifications requiring chemical or physical tests , or both, to determine whether the material delivered meets the requirements , the price to be paid depending on the results of the tests . Until recent years coal consumers purchased coal merely on the statement of the dealer as to its quality , relying on his integrity and on the reputation of the mine or district from which the coal was obtained. It is surprising that the important question whether value was being received for the money expended was not sooner seriously considered . The purchase of coal by specification is an important step toward the conservation of our national mineral resources , for it results in an increased use of the lower grades of coal. The poorer coals find a market by competing with the better grades , not as to the price per ton but as to the cost of an equal number of heat units. This paper gives in detail the results of government purchases of coal for the fiscal year 1908–9 and the list of contracts with abstracts of specifications for the fiscal year 1909–10 , and summarizes the information on this subject obtained by the Survey. It is hoped that this information will promote a better understanding of the specification method of purchasing coal and furnish data valuable alike to coal dealers and coal consumers , so that equitable contracts can be more readily made.

Jan 1, 1910

By Elaine T. Cullen

Human beings are natural storytellers and story listeners. We learn very early that stories entertain us, but also give us the ?rules? about what is expected of us and how to make meaning of our experiences. Stories are integral to our lives, and have great power to change or influence how we think or how we react. They are an innate part of how we learn, and have obvious benefits to trainers or educators who are trying to impact what and how we learn. This paper and presentation discuss the social and cultural power of stories, and how they have been used to develop training for skilled blue-collar workers. Included will be examples as well as suggestions for trainers on where to find stories, what type of stories to pay attention to, and how to use them to improve occupational safety training.

Jan 1, 2008