Search Documents

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 1992

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

To separate complex mineral mixtures according to their dielectric properties. Approach Develop a laboratory-scale continuous dielectric separator to separate mineral mixtures by exploiting their difference in dielectric properties. How it Works Dielectric separation is de-fined as the separation of particles based on their dielectric properties. The uniqueness of the Bureau's continuous separator, called the ?Rotating Drum Dielectric Separator,? is that it contains a high-voltage electrode con-figuration. The drum electrode consists of a series of coaxial parallel wires mounted on the outside surface of an Insulated cylinder. The screen electrode Is a wire mesh, quarter cylinder positioned outside and coaxially with the drum electrode. The drum electrode is placed in a liquid of dielectric constant K with the liquid level just above the drum's axis. The screen electrode is completely Immersed

Jan 1, 1981

By Roy L. Wilfong

Infrared reference spectra are presented of compounds of importance in lead sulfide flotation research. Included are the spectra of several short chain alkyl xanthates of lead and zinc, the corresponding dixanthogen compounds, and the common oxidation products of lead sulfide and their sodium analogs. The spectra of several frequently used industrial flotation reagent xanthates are also presented. A thorough, well-documented discussion is given of the various corrections made to correct the as recorded absorption band data to near absolute values.

Jan 1, 1974

By C. J. Chindgren

A refractory-lined, garage-type automobile incinerator with a natural gas afterburner for air pollution control was cooperatively constructed and tested by the Bureau of Mines and the Wasatch Metal & Salvage Co. in Salt Lake City, Utah. The incinerator is capable of relatively smokeless burning of 32 to 60 cars per day, dependent on the degree to which the cars are stripped prior to incineration. Preliminary burning campaigns indicate the cost of incineration to be approximately $2.75 per car.

Jan 1, 1970

By H. S. Chiang, Zhao. Y. F., G. C. Sun, S. S. Peng

"Chiang; H. S. West Virginia UniversityPeng, S. S. West Virginia UniversitySun, G. C. West Virginia UniversityZhao, Y. F.West Virginia UniversityDust sampling was performed in two longwall faces working in two separate seams. Instantaneous dust samples were measured by RAH's. for various locations In the longwall faces. Preliminary analysis of the data shows that in addition to the shearer's haulage speed, there are four major factors that influence the airborne dust distribution in longwall face areas: locations with respect to the position of the shearer's cutting, hardness of the materials, characteristics of water spray, and roof conditions. This paper presents the effects of those four parameters in detail.INTRODUCTIONA research project was initiated in September 1983 to measure and construct .a dust distribution map for the longwall face. During the first year, airborne dust samplings were performed in two longwall panels located in northern and southern West Virginia and working in the Pittsburgh and Eagle Seams, respectively. The physical parameters and equipment employed for both panels are 1 isled in Table 1. Figure 1 shows the detailed characteristics of the coal seams. Notice in both panels floor cutting was involved either to gain sufficient mining height or to reduce the adverse effects associated with a soft floor.The purpose of the research is to define the dust distribution at any instance in the longwall face area so that proper working positions can be determined and/or effective dust control techniques can be developed.This paper presents the partial results obtained during the first year."

Jan 1, 1988

By Thomas Fraser, J. D. Davis

"INTRODUCTION Preliminary tests of the Oyon coal constituted part of a wartime exploratory and development program in which many agencies participated. The general objective was to find new and adequate source of fuel and other raw materials for greatly expanded industry.The Oyon coal field, known for at least a hundred years to the mining people of Peru, offers a possible source of high-grade process fuel for the growing metallurgical industries of South America and the Pacific coast. Santolalla 4/ reports that low-volatile coal from this region was used in local smelting operations as early as 1850. It has been mined in very small quanti¬ties for many years and used in neighboring mining camps and villages. Small quantities are regularly used at Oroya for the manufacture of carbide, and in recent years small-scale coking operations in specially designed ovens in the region have demonstrated that these coals will make dense coke.During this long period of desultory operations many small openings have been made scattered over a wide area in this general region, indicating very extensive occurrence of the coal measures, although systematic exploration work has not been undertaken. However, current development work of the Banco Minero del Peru has opened up several substantially parallel highly inclined or vertical beds of workable thickness and has followed these deposits to sufficient lateral extent to prove fairly well the existence of substantial reserves on this property."

Mar 1, 1948

By D. L. Nussear, W. E. Wallace, N. Clark, M. Gautaum, G. Hong-Guang

"Results of a research effort directed towards identifying and measuring the genotoxic properties of respirable particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented. Particulate matter emissions from a direct injection diesel engine have been sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust from a caterpillar 3304 diesel engine, representative of the ones found in underground mines, rated 100 hp at 2200 rpm is diluted in a multi-tube mini-dilution tunnel and the particulate matter is collected on 70 mm fluorocarbon coated glass fiber filters as well as on S"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the genotoxic potential. Results to-date on diesel exhaust have indicated that use of a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offers a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within. Protocols have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surf ace and physical properties of the particulate material. Evidence has been gathered to show that diesel soot expresses mutagenic potential as dispersions in DPL in the Ames tests as well as sister chromatid exchange activity in the animal lung fibroblast ·derived V79 cell line. The results are comparable to the standard solvent extraction procedure. INTRODUCTIONDiesel engines are primarily associated with transportation; however, they are also very common in the work place. Of particular concern is the use of diesel engines in mining operations. Currently there are 1,950 diesel machines working in underground coal mines throughout the country. These units are used in 151 mines encompassing nine different states (MSHA, 1991). It is believed the use of diesel powered equipment has contributed to higher productivity in these mines. However, the exhaust from diesel engines operated in underground mines has been a subject of concern during the past decade because of its suspected relationship with health aspects. The particulate matter generated by the diesel engine is of particular concern."

Mar 1, 1992

By B. J. Scheiner

As part of the goal to maximize minerals and metals recovery from primary domestic resources, design factors associated with minimizing current leakage in bipolar cell configurations were studied by the Bureau of Mines as a means of improving the efficiency of bipolar e1ectrooxidation cells. Initial studies that were conducted in a small bipolar cell operating at 140 to 145 volts and 15.4 amp indicated how design factors could be employed to minimize cur-rent leakage around adjacent electrodes during cell operation. Based on these results, a 40-electrode, 108-kva prototype of an industrial-sized cell was constructed and tested for extracting metal values from offgrade molybdenite concentrates. The feasibility of recovering molybdenum and rhenium from the oxidized pulp also was determined. Feed to the process sequence consisted of flotation concentrates containing 16 to 35 pet Mo as molybdenite and 6 to 15 pct Cu. E1ectrooxidation in the prototype cell resulted in 84 to 97 pct Mo and Re extraction with a corresponding energy consumption of 9 to 13 kwhr/1b Mo extracted.

Jan 1, 1979

By D. E. Shanks

As part of its effort to produce cell-grade alumina from clay, the Bureau of Mines investigated the hydrogen chloride gas-sparging crystallization of aluminum chloride hexahydrate (ACH) from aluminum chloride liquor, to provide information for optimizing the crystallization operation. Four parameters important in controlling the crystallization of the aluminum chloride hexahydrate and the concentration of impurities, particularly phosphorus and magnesium, in ACH crystals are (1) aluminum chloride concentration in the feed solution to crystallization, (2) hydrogen chloride gas flow rate, (3) temperature, and (4) concentration of phosphorus and magnesium also in the feed solution. Parameters 1, 2, and 3 affect crystal formation. The combined effects are very important because the phosphorus and magnesium concentrate in the crystals during the early stages of crystal growth. Aluminum chloride hexahydrate of cell-grade purity was crystallized from saturated aluminum chloride solutions containing less than 0.003 wt-pct P205 and 0.010 wt-pct MgO. Crystallization temperatures less than 600 C decreased crystal purity.

Jan 1, 1981

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

A spectrographic procedure applicable to the semiquantitative determination of 29 elements in tungsten is presented. The method is designed to give estimates of impurity concentrations up to 500 p.p.m. Limits of detectability range from 0.3 p.p.m. for the more sensitive elements to 100 p.p.m. for the less sensitive ones. Tungsten metal samples varying in particle size from minus 300-to 30-mesh are excited in the presence of 5 percent germanium with a direct current arc. Germanium acts to stabilize the arc, minimizes the volatilization of tungsten, and serves as an efficient carrier to sweep impurities from the tungsten into the excitation zone. Curves are presented that show the volatilization behavior of germanium, tungsten, and impurities in tungsten at different concentration levels. Data obtained were used as guides in establishing the method of analysis. In the absence of established reliable analytical procedures for determining many impurities in tungsten in the parts per million concentration range, the spectrographic method described here should prove to be helpful in evaluating high-purity tungsten.

Jan 1, 1961

By J. D. Marchant

The Bureau of Mines studied solid-state electromigration to determine the value of the technique as a method of purifying cerium metal. Cerium metal in bars 6 inches long and 1/2 inch in diameter was refined at 600° C by solid-state electrolysis to remove iron, copper, and manganese. Iron and manganese were electrotransported to the anode and copper was electrotransported to the cathode. The concentration of iron at the anode of a cerium bar was 800 times greater than the concentration at the cathode. The concentration of manganese at the anode was twice the value at the cathode. The concentration of copper was 170 times greater at the cathode than at the anode. A radiotracer technique was used to follow the iron migration in the cerium metal. Molybdenum, silicon, and aluminum impurities were not electrotransported.

Jan 1, 1967

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By R. L. Andrews

The Bureau of Mines investigated means of electrodepositing iridium to form thick coatings suitable for the protection of such metals as tungsten and molybdenum, which oxidize rapidly at high temperatures. Using a fused sodium cyanide bath, thick, adherent, and coherent deposits of iridium up to 15 mils thick were plated on tungsten and molybdenum substrates at 600° C and current densities of 10 to 100 ma/cm2. Limited oxidation testing of molybdenum encapsulated with pure iridium indicates that the coating may offer protection to approximately l,000° C in flowing air, but that at higher temperatures, the volatility of its oxide limits use of pure iridium. Alloy coatings of iridium with platinum, palladium, and rhodium up to 4 mils thick were formed from a fused sodium cyanide electrolyte; because their oxides are less volatile, these alloys may protect substrates at higher temperatures. Deposits made from aqueous electrolytes either had very low rates of deposition or were highly stressed and cracked when heavy deposits were made.

Jan 1, 1967

By N. A. Eilertsen

This report describes field investigations conducted in 1953 of two occurrences of manganese and a separate magnetic anomaly in the Southern manganese district of Aroostook County, vicinity of Houlton, Maine -the Pierce deposits, in Hammond Plantation Township; the Burnham anomaly, also in Hammond Plantation; and the Nickerson-Farm prospect in Hodgdon Township. The manganese occurs in a thinly laminated sedimentary rock containing manganiferous carbonate interlayered with fine-grained metamorphosed sediment, rich in chlorite or hematite. The surrounding rocks are mostly dark gray-green slates. Samples composited for metallurgical testing from the Pierce deposits and the Nickerson-Farm prospect assayed 9.0 to 12.3 percent of manganese. More than 90 percent of the manganese could be extracted with sulfuric acid, but in most instances 30 to 40 percent of the iron was also extracted. Leaching tests indicated that, after being reduced in a hydrogen stmosphere at 600° C., about 85 percent of the manganese could be selectively extracted by a solution of ammonia-ammonium carbonate with iron extraction of only 14 percent.

Jan 1, 1958

By George E. Blandford

A deterministic model to assess the hydrologic impact of small watersheds subjected to unsteady storm events is presented. The overland flow model is based on the kinematic wave approximation coupled with a Green-Ampt infiltration equation. The Green-Ampt infiltration parameters are estimated using the USDA-ARS parameter estimation technique which is based on soil moisture-tension data. A Galerkin finite element formulation of the kinematic wave approximation is presented for the deterministic analysis of overland flow on small watersheds. The finite element formulation includes linear, quadratic and cubic Lagrangian one-dimensional spatial elements. A linear time variation is assumed which includes both explicit and implicit time marching algorithms, depending on the choice of the time weighting parameter. The implicit time algorithms result in a system of nonlinear equations which are evaluated using a modified Newton-Raphson iteration scheme. Initial solution estimates are generated using a linear finite difference procedure. The coupled infiltration overland flow model is tested using storm data for impervious surfaces, a laboratory soil flume, and two natural, USDA-ARS experimental watersheds.

Jan 1, 1983

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960