Search Documents

By W. L. Anderson

Standard tellurium analytical procedures were modified to obtain the greater sensitivity needed to support a survey of tellurium resources by the Bureau of Mines. Resulting volumetric and spectrophotometric methods for determining tellurium in all types of tellurium-containing materials are described. Sample decomposition and preliminary separations of interfering selenium, gold, and silver are the same in both procedures. The volumetric method is applicable to samples containing a minimum of 10 parts per million of tellurium, In this method the tellurium is reduced to elemental form, and the colloidal suspension is titrated with 0.01 normal iodine solution. The weight of sample for analysis, from 0.25 to 10 grams, should be selected so that the sample contains 0.1 to 5 milligrams of tellurium. To insure accuracy, duplicate samples should be run and the results averaged, particularly on samples of low tellurium content: The limit of determination is 0,001 percent tellurium, which is equivalent to 0.1 milligram of tellurium when using a 10-gram sample. The spectrophotometric method is particularly applicable to low-tenor materials containing from 0.5 to 50 parts per million of tellurium. Up to 10 gram samples are required for making accurate determinations in the low-concentration range. The sample used should contain between 5 and 100 micrograms of tellurium. The turbidity of a colloidal suspension of tellurium prepared from such a sample is determined in a spectrophotometer .t at a. wave-length of 440 millimicrons, and this value is compared with those of standard samples containing known amounts of tellurium.

Jan 1, 1963

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By J. L. Stauffer, S. L. Lacey, L. J. Gaydos, L. M. Demers, D. C. Kuhn

"Tumor necrosis factor alpha (TNFa) and thromboxane A2 (TXA2) are major products of the activated alveolar macrophage and serve as key mediators of lung injury. In order to determine if the synthesis ofTXA2 and the release ofTNFa are associated, the production of these inflammatory agents by the human alveolar macrophage (AM), as a result of activation by lipopolysaccharide (LPS), was assessed in the absence and presence of the thromboxane synthase inhibitors UK 38,485 (Dazmegrel) and OKY 046. UK 38,485 and OKY 046 inhibited both LPS-stimulated TXA2 production and TNFa release in a dose-dependent manner. Prostaglandin E2 (PGE2) production was not increased by UK 38,485 or OKY 046. Neither LPS nor UK 38,485 had any effect on LT84 production by AM. Neither UK 38,485 or OKY 046 had any effect on LPS-stimulated interleukin-I beta release. However, the TXA2 mimetic, U46619, did not stimulate TNFa release by AM either in the absence or presence of UK 38,485. These findings suggest that 1) UK 38,485 and OKY 046 are inhibitors of both TXA2 production and TNFa release by activated human AM, 2) UK 38,485 probably does not exert its inhibitory action on TNFa release through effects on eicosanoid production and 3) the possibility that TNFa- and TXA2-induced lung injury may be subject to amelioration by imidazole-based compounds should be further evaluated.IntroductionTumor necrosis factor alpha (TNFa), produced by monocytes and macrophages, is a potent peptide mediator of lung injury (1,2). The exaggerated release of TNFa has been implicated in the etiology of acute lung reactions such as septic shock of bacterial or viral origin (3,4). The role of TNFa is expressed primarily through its ability to activate a variety of cell types within the lung environment including polymorphonuclear leukocytes (PMNs, ref. 5), type II epithelial cells (6) and fibroblasts (7). The role of lipid mediators in lung disease has also been extensively characterized (1). In particular, the relationship between pulmonary inflammation and fibrosis and the production of oxygenated derivatives of arachidonic acid (here termed ""eicosanoids"") appears to be a key factor in a variety of disease processes in the lung (8). The alveolar macrophage (AM) synthesizes primarily prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (LT84, ref. 9). These eicosanoids have been shown to produce a variety of effects in the lung including bronchial smooth muscle dilatation (PGE2, ref. 10), vascular smooth muscle contraction and platelet aggregation (TXA2, ref. 11) and oedema and immune cell extravasation (LT84, ref. 12)."

Nov 1, 1995

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By Edward D. Thimons

The Bureau of Mines has developed a damage-resistant brattice, intended for use as a stopping in locations where blast damage to stoppings is a problem, the roof is relatively flat, and the differential pressure across the stopping is not high. Damage-resistant brattices consist of a series of vertically hung brattice panels joined to each other by Velcro connections that improve the airtightness of the brattice. When the brattice is subjected to strong blast forces, the Velcro connections peel apart, allowing the panels to open without incurring damage. The Velcro connections can then be resealed in a matter of minutes. A preliminary test in the Bureau's Safety Research Mine and subsequent long-term testing at the White Pine copper mine in Michigan and the Retsof salt mine in New York show that damage-resistant brattices withstand blasting better than conventional stoppings, while still performing as efficient air barriers when the Velcro connections are sealed.

Jan 1, 1978

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

By Chester L. Arnold, Reinhardt Thiessen, Alexander Lowy

"INTRODUCTION Peat is the accumulated mass of plant materials that remain after partial decay under specific conditions. In the swampy peat bogs dead material which falls on the surface immediately is attacked by fungi and aercbic bacteria. Decay under these conditions is rapid, but of relatively short duration, since the constant addition of new material soon forces the older layers below the water level, in this position, without access to oxygen, the plant constituents are attacked mainly by anaerobic bacteria, and decomposition proceeds slowly. The largest part of peat is contributed by the woody tissues of plants, the chief constituents of which are cellulose and lignin, together with a small proportion of hemicelluloses. During the normal process of biological decay celluloses disappear more rapidly than lignin. The result is a complex substance known as humin, from which the humic acids may be extracted.In 1826, Sprengel 5 found that when decayed plant materials were extracted with alinnli and the resulting black liquid acidified with mineral acid a brown gelatinous precipitate was formed. To this product, which was a brown amorphous powder when dry, he gave the name ""humic acid'. Since that time, chemists have used the name rather loosely to designate products which have been isolated by very diverse means from soils, decayed woods, peat, lignite, and coal. An excellent review of the early work on humic acids was published by Baumann 6 in 1909. This publication aroused the interest of Oden, who then investigated the humic acids. An account of Oden’s work, as a good survey of the literature, is contained in his monograph “Die Huminsauren”. 7"

Nov 1, 1934

By Spencer P. Howell

One of the important problems in metal mining , tunneling or quarrying is the most economical method of bringing down the ore or rock . The two factors having great influence in determining this are arilling and blasting costs . In considering the efficiency of the explosive used , the diameter of cartridge has always been supposed to play an important part . However , the Bureau's attention has been called to the lack of definite data on the effect of cartridge diameter on the strength and sensitiveness of high explosives . This information is especially valuable to the user of explosives as it assists him to determine what diameter of borehole is most economical . A paper* on "The effect of cartridge diameter on the strength and quickness of high explosives " was submitted to the sub- committee on Drills and Drill Steel of the 24th Annual Convention of the American Mining Congress by Charles S. Hurter , Technical Representative of the E. I. duPont deNemours and Co. In this paper Mr. Hurter points out that the physical characteristics of an explosive most affected by the diameter of cartridge are rate of detonation and sensitiveness to explosion by influence , and that both increase with increase in diameter . As there is a continuing tendency to the use of smaller diameter drill holes in order to lower drilling costs , and as the smaller drill hole requires a smaller diameter of explosive cartridge than larger drill holes do , this paper has been prepared to show the effect the diameter of cartridge will have on the strength and sensitiveness of the high explosives which may be used . Accordingly , the Bureau of Mines , in cooperation with the Institute of Makers of Explosives , has carried out a series of tests to show the effect of cartridge diameter on the strength and sensitiveness of certain high explosives .

Jan 1, 1923

By V. M. Benson

A simplified, routine method for determining lithium in lithium-bearing rock is presented. The sample is decomposed by repeated treatments with nitric, hydrofluoric, and perchloric acids. Since this procedure does not appreciably dissolve beryl, interference by beryllium (the principal interfering cation) is minimized for most samples. The salts are brought into solution with water and enough citric acid-ammonium citrate buffer is added to make the final volumetric dilution 0.20 M with respect to citrate. The addition of citrate greatly reduces anion interference in the hydrogen-oxygen flame, slightly increases the intensity of the lithium 671 millimicron emission line, and reduces the effect of most of the interfering cations to the extent that analytical separations are not necessary. The accuracy of results of single determinations of lithium in a pegmatite containing spodumene, lithium-bearing mica, and beryl are approximately equal to that obtained by other flame methods, INTRODUCTION This investigation was undertaken in Bureau of Mines laboratories to develop a reliable, rapid, routine analytical method for determining lithium in lithium-bearing minerals. The requirements of the procedure were that the method should be applicable to the analysis of a variety of lithium-bearing ores and test products, and the results would be reasonably accurate for materials containing 0.05 to 8 percent Li20.

Jan 1, 1961

By Bruce I. Thomas

The occurrence of tin-bearing gravels along Tozimoran Creek in central Alaska has been known for a number of years. In September 1944 the Bureau of Mines investigated an area approximately 1,000 feet long and 200 feet wide along Tozimoran Creek to deter-mine the cassiterite content of the stream gravels, which are about 4 feet deep and covered by 3 feet of overburden. Nine trenches and two shafts were excavated, from which samples of the underlying gravels were taken. This report contains a discussion of sampling methods and tables giving the results of analyses.

Jan 1, 1948

By Charles Vaught, Warren G. Lacefield, Ronald D. Wasielewski, Philip K. Berger, Henry P. Cole, John V. Haley, Shannon L. Price

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Computerized searches of the relevant data bases were carried out, along with identification of relevant articles and materials by personal contact with experts in many fields. The citations listed in this bibliography resulted from this systematic literature search and review. The computer searches and an analysis of this literature are described in technical report 1. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/ technical workplaces were described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training was explored. Research and development activities that may improve mine health and safety training were suggested. Most of the entries in this bibliography were assembled in 1984 through 1985. Study of these materials contributed to the completion of the project research that followed. This later work is reported in the project technical report 2 and the final report. This bibliography is most useful when combined with examination of technical reports 1 and 2 and the final project report.

Jan 7, 1988

By R. O. Dannenberg

This Bureau of Mines report describes the results of research to develop a process for recovering additional beryllium from a commercial mill waste product, fluoferrate leach residue. Forty-five percent of the total beryllium in the leach residue was recovered in a beryllia product assaying over 98 pct Be0 by a process comprising (1) leaching with 1 N sulfuric acid, (2) adjusting the acidity of the leach liquor to pH 2, (3) extracting the beryllium with di-2-ethylhexyl phosphoric acid (EHPA), (4) stripping the loaded extract with sodium hydroxide solution, (5) boiling the sodium beryllate strip solution to precipitate beryllium hydroxide, and (6) calcining the beryllium hydroxide. Calculated reagent requirements per pound of Be° recovered by a proposed flowsheet were 28.1 lb sulfuric acid, 0.04 lb flocculent, 0.15 lb EHPA, 0.06 lb isodecanol (IDA), 0.22 gal kerosine, and 6.3 lb sodium hydroxide.

Jan 1, 1966

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By Jalna R. Zatko

The Bureau of Mines has developed and constructed an apparatus that is capable of measuring concentrations of high-molecular-weight polymers in solution at 10 ppm and less. A means for determining low concentrations of polymeric solutions was devised that was independent of slight fluctuations in solvent quality in order to measure polymers in effluent prior to recycling of the recovered solution. The concentrations of polymers ore related to a measured pressure drop observed during turbulent flow of the solution. Low concentrations of polymers of ethylene oxide and acrylamide (frequently used as flocculants for clay waste systems) in aqueous and salt solutions have been successfully measured on the apparatus constructed by the Bureau.

Jan 1, 1981

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

By R. T. DeWoody, W. C. Miller, W. Chester

Studies were made to determine the effect of the shape of a pneumaticrock- drill exhaust muffler on its efficiency, and the origin and reduction of exit noise from the mufflers. Tests of mufflers of three different shapes proved that the shape is not critical and that a muffler could be incorporated into the shell of the drill. Petal diffusers are beneficial in reducing exit noise but add another projection to the machine. Increasing the number of exit openings while maintaining the same area of exit opening has a markedly beneficial effect on the exit noise and appears to be the most satisfactory treatment.

Jan 1, 1964

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1330, however, was unusually dry and represents what may be termed "extreme low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscohonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.

Jan 1, 1931

By K. K. Kelley, L. B. Pankratz, W. W. Weller

Mullite is a substance of prime importance in ceramic technology . Despite this fact , its thermodynamic properties have received little attention . A Bureau of Mines literature survey disclosed the absence of lowtemperature heat capacity data , the absence of an experimental entropy value for 298.15 ° K , and the lack of heat content data beyond the temperature range from 298° to 576 ° K. Data supplied in this Bureau report fill these gaps in the thermodynamic knowledge of mullite . According to equilibrium phase studies of Aramaki and Roy ,3 the mullite phase melts congruently at 2,123 ± 15 ° K , and the equilibrium crystallinephase composition extends from Al Si2013 to Al6.8 Si₂ Q4.2 . The results in this report are for the stoichiometric composition , Al Si¿Qз . • Heat capacity measurements were made over the temperature range from 50 ° to 298 ° K , and the entropy at 298.15 ° K was evaluated . Heat content measurements covered the temperature range from 298 ° to 1,800 ° K. Heat content

Jan 1, 1963

By Raymond G. Travis

This paper, which describes mining methods and practices at the Hurricane Creek bauxite mine of Reynolds Mining Corp. in central Arkansas, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Hurricane Creek mine is in sec. 12, T. 2 S., R. 14 W., and sees. 7 and 18, T. 2 S., R. 13 W., Saline County, Ark., about 4 miles east of Bauxite. (See fig. 1.) Bauxite has been mined underground at the Hurricane Creek property since 1942. The operation is notable for relatively high recovery of bauxite under the adverse conditions of unconsolidated water-bearing overburden and unstable clay floor. Controlled caving, timbered stope walls, and efficient drainage systems on the surface and underground have minimized the problems and raised ore recovery about 25 percent above that formerly obtained.

Jan 1, 1961

By Stephen Krickovic, J. E. Carpetta, T. D. Moore

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973