Search Documents

By Floyd D. Everett

The J. B. fluorite deposit is in the Washington mining district, southwestern Beaver County, Utah (fig. 1). Fluorite outcrops were found during 1942, and three lode claims wore located. Little work was done on the property until October 1943, at which time the Bureau of Mines started development to determine the subsurface extent of the fluorite mineralization exposed at the surface. The most prominent rocks in the J. B. mine area are porphyries, which vary considerably in composition. Dacite porphyry appears to be the most common host rock for the fluorite-quartz-calcite lenticular masses. The dacite porphyry in the area is highly brecciated over a strike length of more than 1 mile. Fluorite deposits in the brecciated zone cover a strike length of approximately 400 foot. The fluorite lenses range in length from 40 to 200 feet and in width from 4 to 10 feet (fig. 2). The Bureau of Mines work on the J. B. property was started in October 1943 and completed in October a year later. The work consisted of surface trenching by bulldozer and hand methods, shaft sinking, drifting, and crosscutting. Eleven trenches totaling 1,800 linear feet were excavated. An inclined shaft was sunk to a depth of 105 feet, and from thin shaft 577 feet of drifts and crosscuts were driven to outline the extent of the mineral deposit (fig. 3). Two hundred ninety-seven samples were taken in the surface trenches and underground workings. The locations of the samples and analyses arc shown in accompanying figures and tables. Results of metallurgical tests comprise the concluding section of this report.

Jan 1, 1950

By T. J. Ballard

The Union Copper mine is in the Gold Hill district; Rowan and Cabarrus Counties, N. C. The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907. As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes totaling 2,500 linear feet were drilled to delineate the ore body. Analyses 205 core samples were made. Tabulations of sample analyses and drill-hole logs are presented in this report.

Jan 1, 1948

By George W. Heim

Before and during World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for development included those expected to contain metals of importance in the successful prosecution of the war. This report describes the work performed and results obtained in developing the Daggett Chief manganese deposit near Manila, Daggett County, Utah (fig. 1), during 1941. The work comprised mapping and a study of the geology by the Federal Geological Survey, and bulldozer and hand trenching, sinking of two shafts, and sampling by the Bureau of Mines. Work was started April 17, 1941, and was completed June 28, 1941. Two bulk samples for metallurgical testing were taken.

Jan 1, 1950

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Radford Schantz

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA). San Bernardino County. California During field work. BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1.188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) fun access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion. $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

By George H. Schnakenberg

This Bureau of Mines publication describes a passive personal sampling device for N02 in air, developed by the New York University Medical Center under Bureau Grant G0133066. The sampler has been successfully demonstrated in the field and in the laboratory. In corroborative laboratory trials the agreement with reference method is excellent. The overall accuracy is approximately ±5 pct of reading to a precision of about ±l pct. All evidence indicates that these samplers should indicate the time-weighted-average N02 concentration to the above accuracy and precision equally well in the field since effects of wind velocity and relative humidity are negligible and the effects of temperature are about 0.1 pct per °F. The duration of exposure and the approximate temperature are the only data that need to be collected in the field. A two-step analysis procedure in field or service laboratory is then used to obtain the total cumulated exposure to N02 in parts per million-hours (ppm times hours), which can be converted to the time-weighted-average concentration of N02 in ppm by dividing cumulated exposure by the duration of the exposure.

Jan 1, 1976

By N. C. Dunham

"The Bureau of Mines exploratory work on the Bear Lodge, Wyo., fluorite property wider the strategic minerals Program was completed in November 1944. Exploration consisted of surface trenching, shaft sinking, and drifting at shallow depth. Doak C. Cox of the Federal Geological Survey visited the area during the latter part of 1944 and napped the Bear Lodge property.The Bear Lodge property is situated in the Black Hilts National Forest in eastern Crook County, Wyo., 6 miles north of the community of Sundance (fig. 1). Sundance is 29 miles northwest of Upton, Wyo., a station on the Chicago, Burlington, & Quincy Railroad and 43 miles southwest of a siding on the Chicago & Northwestern Railroad, 3 miles south of Belle Fourche, S. Dak. U. S. Highway 14 passes through Sundance in an east-west direction. Sundance may be reached from the south over U. S. Highway 85 and Wyoming State Highway 585.The Bear Lodge property i a situated in the Boer Lodge Mountains in secs. 15, 22, and 23, T. 52 N., R. 63W., 6th P.M.The topography in the vicinity of the fluorite deposits consists essentially of rounded hills which slope gently to the valley floors. Near the north end of the Property the terrain steepens locally, and the canyon walls are Precipitous along the courses of several streams. There is an adequate supply of water and native timber for mining purposes. The average elevation near the deposits is 5,700 feet.The climate of the region is relatively moderate. The summers are usually warm, with frequent rainstorms. Temperatures often fall below zero during the winter months. Snowfalls are moderate to heavy.Fluorite occurrences in the Bear Lodge area have been known since 1914; however, fluorite was not discovered on the Bear Lodge property until 1943, when prospectors working on a nearby manganese deposit found fluorite mineralization in the limestone. No production has been recorded from the property."

Apr 1, 1946

By Thomas R. Bur

This method of performing general transformations by use of Eulerian angles greatly reduces the time required for the determination of values for the elastic compliance constants (sij), elastic stiffness constants (cij ), Young's modulus, shear modulus, or Poisson's ratio for any orientation the cartesian coordinate system in an anisotropic material.

Jan 1, 1969

By Herbert R. Babitzke

As part of a project to develop refractory metal alloys suitable for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation-hardening techniques to columbium and tantalum alloys. Thirty-three alloys were evaluated to determine their formability, strength, and oxidation resistance. Three alloys had tensile strengths near 40,000 psi at 1,200° C: Cb-1N-5W-5V-10Hf (No.4), Cb-15Hf-5W-0.5B (No. 31), and Cb-15Hf-SW-IB (No. 32). Oxidation resistance of the high-strength alloys was good. Alloy4 gained only 34 mg/cm2 at 1,200° C, and 21 mg/cm2 at 1,000° C in 2 hours. Hot forming was done without any protection from oxidation.

Jan 1, 1968

By Kenneth J. Miller

To determine the effectiveness of the many new flocculants available to the coal industry 20 of these reagents were evaluated treating slurry feeds to four refuse thickeners. Settling rates and supernatant liquid clarities were determined for each of the flocculants on the four slurries, and zeta potential measurements of the slurry solids were made. The test results showed that the flocculants provided comparable results when judged categorically as anionic, nonionic, or cattonic. It was also apparent that control of zeta potential insures maximum benefit from a flocculant.

Jan 1, 1968

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By J. E. Chilton

The Bureau of Mines has examined the operation of an oxygen sensor manufactured by the City University, London, England. The sensor produces a current proportional to the oxygen concentration by reacting oxygen at a nonconsumable cathode. The sensor design is unique in that the primary mode of oxygen transport to the cathode is by diffusion through a capillary, The sensor using this design has a stability of 0- to 0.02-pct reading change per day over a 4.7-month test, small temperature coefficient of 0.29-pct reading change per °C, and small pressure coefficient of 0.34-pct reading change per 1,000-ft altitude change, If this sensor were incorporated into an oxygen detector or monitor, this would be a distinct improvement in electrochemical-type oxygen analyzers and would be useful to the mining industry.

Jan 1, 1983

By Aarne Visnapuu

Dissociation and vaporization of gold chlorides and bromides were investigated by a static pressure method and by Knudsen cell mass spectrometer. Two distinct chlorine and three distinct bromine pressure-temperature relation-ships were observed for the respective salts. The chlorine pressures are attributed to the dissociation of Au2Cl6 and Au2C12, and the bromine pressures to the dissociation of Au2Br6, Au2Br4, and AU2Br2, These pressure-temperature relationships were used to calculate dissociation pressure equations, enthalpies, and entropies of dissociation for each salt. Mass analysis of the vapors over AU2Cls between 83° and 152° C confirmed the existence of gaseous AU2C16. Ionization potential of this molecule is 11.0±0.1 ev and enthalpy of vaporization is 28.l±2.0 kcal/mole. Mass analysis of the vapors over the gold bromides detected only Bra in the temperature range 15°-150° C.

Jan 1, 1971

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By W. R. Crane

Subsidence and ground movement are phenomena common to and attendant upon practically all large-scale mining operations, and under certain conditions may occur in all workings, large and small. The interpretation of the cause of failure in rock masses involves a study of the nature of plants of weakness common to all rocks. The dominating planes of weakness can readily be determined by observation in any given locality, and in order of importance in the study of subsidence are (1) faulting planes, (2) bedding planes, (3) joint planes, and (4) other prominent planes of weakness such as thrust and shear planes and contacts. This report has mainly to do with the third item, joint planes, and is a preliminary statement which t to be followed by a more complete report in bulletin form.

Jan 1, 1931

By P. T. Brooks

This Bureau of Mines study describes a process for recovering nickel, cobalt, molybdenum, and chromium contained in complex waste superalloy grindings that, for lack of an economical domestic recovery process, are being largely marketed abroad. The process, devised by laboratory scale operations, includes scrap preparation, dissolution of metallics in hot chlorinated acidic liquor, carbon adsorption, three successive solvent extraction separations, and selective chemical precipitations. Nearly 90 percent of the nickel, cobalt, molybdenum, and chromium were separated and recovered as oxides, carbonates, and basic sulfate products.

Jan 1, 1969

By Charles B. Kenahan

The chemical and galvanic corrosion properties of commercially pure titanium, a titanium-manganese alloy, a titanium-aluminum-tin alloy, 2 titanium-copper alloys, and 2 titanium-aluminum alloys were studied. Tests were conducted in synthetic ocean water, tapwater, 1-percent sodium hydroxide, 5-percent ferric chloride, and 5-percent ammonium sulfate solutions, various concentrations of sulfuric and hydro-chloric acids, and 1-percent oxalic acid. All tests were carried out at 35° or 60° C., with a flow of air or helium. Dissimilar metals involved in galvanic-couples experiments were aluminum, magnesium, and stainless steel. Electrode-potential measurements on single (uncoupled) specimens were also measured. Commercially pure titanium and the titanium-base alloys were generally quite similar in their resistance to corrosion, whether alone or in. contact with a dissimilar metal. Contact with the titanium metals caused aluminum and magnesium to corrode by galvanic action. Coupling with stainless steel in sulfuric acid solutions decreased the normal corrosion rate of the titanium metals. Contact with aluminum in air-aerated oxalic acid and 0.1N sulfuric acid solutions resulted in cathodic corrosion of titanium and the titanium-base alloys; however, there were a few exceptions. The copper alloys showed better corrosion characteristics than titanium in certain sulfuric acid solutions but were more susceptible to chemical attack in some hydrochloric acid solutions.

Jan 1, 1958