Search Documents

By McHenry Mosier

The object of this investigation is to determine the field for the use of detachable bits in metal mines of the United States by correlating the data developed through the experience of mines using these bits. Most of the metal-mining districts in the Middle Western and Eastern States already have been visited. The purpose of the present circular is to define the problem and to discuss the factors that must be considered in order to determine, under different operating conditions, the advantages and disadvantages of this type of bit. Some of the data obtained to date are presented to emphasize points made in the discussion. It is hoped that, as the study progresses, a great many data on drilling will become available. It is evident that since in some cases these data will be confidential they cannot, therefore, be published except as they may be included in average figures covering several different mines. Some data already secured are of this nature, Although considerable information on drilling operations has been gathered at different mines, there were only a few instances in which there were available complete data on all the factors entering into the total cost of drilling with detachable bits and with conventional bits on regular drill steel.

Jan 1, 1936

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

Mine waste and mine reclamation are topics of major interest to the mining industry, the government and the general public. This publication and its companion volume are the proceedings of a conference held in Pittsburgh, April 19-21, 1988. There were nine sessions (50 papers) that dealt with the geochemistry, hydrology and problems of mine waste and mine water, especially acid mine drainage. These comprise Volume 1. The nine sessions (43 papers) that dealt with reclamation and restoration of disturbed lands, as well as related policy issues, are included in volume 2. Volume 2 also contains the ten papers that pertained to control of subsidence and mine fires at abandoned mines. Poster session presentations are, in general, represented by abstracts; these have been placed in the back of both volumes.

Jan 1, 1988

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By G. H. Damon

Since 1963, Bureau of Mines Information Circular 8179 has served the mining industry as a fundamental safety guide in the field of blasting agents. In the intervening 14 years, many changes have occurred, and this report presents revised and new recommendations which recognize these changes. For example, AN-FO is now supplied mostly premixed, whereas in 1963 much of it was mixed by the blaster; aluminum metal (A1) and other fuels are now often added to AN-FO to increase strength, and flake aluminum powder is used as a sensitizer in water gels; and water gels or slurries that are now extensively used were just coming into practical use in 1963. To provide the widest possible margin of safety, some of the Bureau's recommendations are more stringent than existing regulations,

Jan 1, 1977

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

This report provides concepts for two automated longwall mining systems; one for operation in a 42 to 57-inch thick section of the Lower Kittanning coal seam, the other in a 57 to 72-inch thick section of the Pittsburgh seam. The Lower Kittanning concept uses a single-drum bidirectional shearer and 500-ton capacity 4-leg chocks and the Pittsburgh concept uses a double-drum shearer with 500-ton shields. Each concept is designed to produce in excess of 2,500 tons of clean coal per shift with a 6-man face crew. The automated longwalls consist of off-the-shelf control system hardware attached to standard longwall equipment. Control hardware includes a control and display console; prime and backup mini-computers; multiplex data transmission, power, and control lines; several remote terminals which serve as interface junctions; and various sensors and actuators located on the longwall equipment. The system can be operated either fully automatically, remotely or manually.

Jan 1, 1976

By Robert L. Lagace

[Suuple Iheorctrccil models are I'M lllolalcd to cltaraclerl/c medium frequency (MF) radio vase pi opaiation in undcrgiounli room arid pillar coal mines fur the purpose of predleiln the most lavolable operating fIegtucncics,md nr,ixunum communic;IIIoil ranges for pottahIe rldu)s with I top antennas. I or conductul IrCC areas, at hree layer propaeaIion IltodcI wit II a Iiallsmissloil IIIIi- lhlllllIIal'u11 lot the plupa!edti ii unlstallt Iris been dcvcloped ;md verified experimentally. 1 lie mode u1 propaCaUetl lakes Ills form of i parallel plane (0,t)) TIM lransnussu)nhne 1% PC of mode with the electric held vertical and the magnetic held hoti/cntal t itliin a planar coal scam in which the tunnels Can he ignored and which 1s hounded above and below hp richer conductivity rock. 1lie model lilt the data best river the 200 io 1000 kH/ frequency hand and exhibits a rc;;lon of optlnrul1l Pelffelntance, with respect Io maxnluiulg radio Communication range, between 300 and 100 klf/. Maximum cunununlcatrorl ranges are sliongls dependent oil the sigiial alleilliatroil sale, ant) Illelclulc on the electrical conductivltles of the coal seam and surrounding ruck. These ranges v;ny tutu about ,,5 Io 100 nleleis Ill a high Iuss scam such as the Ilelllit No. fl to about .100 to 400 meters in a low loss seam such as the Pittsburgh foil portable intrinsically safe radios. The ieslllls die haled on the comparison oftheorc' and experiment for eleven n n. ill sesen coal seams. V OT ate is dice: a conductor such as a power Cable, is present a model has been developed for the coupling of loop antennas to a low loss Coaxial TEM ti;u?smisslon line mode in which the cable acts as the inner conducl,lr and the rock above and below acts as the outer conductor. The electuc and md' nctic Itelds for till` (node are apprlixitllatcly transverse to the cahlC and fall oil expontially with distance in the transverse plane. The principle of reciprocity is used to simplify the analysis. More expelitnental data arc needed to help resolve discrepancies between the theory and the limited data available to date.]

Jan 1, 1980

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California Fn 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemical manufacturing; a shift in requirements from metals to nonmetals, from inorganics to organics, from natural to synthetic materials, and from distant to local sources of supply.

Jan 1, 1965

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California Fn 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemical manufacturing; a shift in requirements from metals to nonmetals, from inorganics to organics, from natural to synthetic materials, and from distant to local sources of supply.

Jan 1, 1965

By E. J. Gleim

A study of the records on file in the Bureau of Mines reveals that moray fire in coal mines have been started by electrical equipment or circuits. There the fires were of undetermined origin, electricity often was Strongly suspected as the probable cause. While it is unfortunate that positive evidence as to the cause is so often lost in the general destruction resulting from fires, there are many lessons to be learned from fire s in which the origin was definitely established as electrical. For modern high-speed methods of producing coal, electrically operated machinery has become virtually indispensable underground. With increases in the amount of equipment it has not always been necessary to increase the number of circuits in the mine where direct current is mainly used, but it has been necessary to increase the carrying capacity of these circuits. For example, lends such as heavy-haulage units drawing 1,000 amperes or more have brought boat the introduction of 6/0 and "No. 9 section" trolley wires. This has not made the task of fire prevention any easier, for it has meant that circuit breakers s must be set so high that partial short circuits fail to open them, therefore an arc of considerable proportions can be maintained without causing the, beaker to open. Thus, if as fall of roof brought a trolley wire down against a loaded car of coal, an arc might be struck that would ignite they cowl without opening the circuit breaker.

Jan 1, 1937

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By D. A. Paice

A portable calibrator to check tie trip setting of dc circuit breakers within an accuracy of +5% has been developed for the Bureau of Mines. It operates from a 300 volt dc trolley wire to provide controlled current pulses of 120 milliseconds duration and continuously adjustable from 1400 to 3600 A. These current pulses enable a breaker dc trip current to be determined and subject the contacts to full current rating. The equipment is simple to use and weighs 86 pounds. Connections are made with protected, clamp-on leads which are separately connected and weigh about 22 pounds. An accurate calibration procedure takes less than 5 minutes to complete.

Jan 1, 1978

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

Fresh coal refuse was sampled at 21 US mines. Five of the sites were drilled, sampled and tested more extensively. Field tests included Standard Penetration tests, and in-situ density determinations. Laboratory testing included specific gravity, gradation, maximum, and minimum density tests, as well as 9-inch) drained triaxial tests, 9 and 10-inch, permeability tests, slake-durability tests, and accelerated slaking tests. Some refuse sites had significantly lower shear strengths and permeabilities in old, slaked or weathered material than in fresh refuse. Testing did not show useful correlations between strength and permeability changes and other material properties which could serve as "predictors". Testing of refuse under "accelerated slaking" conditions showed promise as a comparative tool and as a potential means of preparing artificially aged samples for evaluations of long-term behavior. The state-of-the-art in slaking research, and the implications of slaking on coal refuse disposal, and on practical methods of managing slaking, were also studied.

Jan 1, 1981

By Ivette E. Torres

Aruba, formerly a. part of the Netherlands Antilles, separated on January I, 1986, and became an autonomous part of the Netherlands. Full independence of the island from the Netherlands is scheduled for 1996. In this chapter, however, Aruba's statistics are included with those of the Netherlands Antilles. Tourism continued to be the main industry of the island, which continued to depend heavily on imports, mostly from the United States. During the year, the Government was preparing legislation to regulate the exploration of oil deposits in the relatively shallow sea around Aruba.

Jan 1, 1989

By Neil J. Mansfield

Tool manufacturers are required to provide declarations of vibration emission values in order to sell their tools within Europe. To ensure that users can compare results obtained from different manufacturers, the declared values must be obtained using a methodology as specified in the relevant test code (such as in the ISO 8662 series of standards). In most cases, the vibration emission values obtained using test codes under-estimate the vibration that an operator will be exposed to when using the tool on a work-site. A further problem with manufacturers’ data is that usually only a single value is provided for a tool. This is despite many factors affecting the vibration emission, including inserted tool type, work piece, operator technique, tool condition. New improved test codes are in the process of being developed. In order to provide guidance to users on how to interpret manufacturers’ data, a Draft CEN Technical Report (Draft CEN/TR 15350 (2005)) was developed. Part of the CEN/TR provides multiplication factors for combinations of task and tool type. For example, data obtained from electrical hammer drills (tested according to EN 60745-2-6:2003) should be multiplied by 2, for hammering applications, in order to obtain an estimate of the vibration emission during work. In response to concerns from industry, the UK trade association OPERC have, in collaboration with hire companies and tool manufacturers, established a freely accessible online database of tool emission values based on independent tests carried out under simulated work-site conditions. This paper reports some of the data obtained from electrical hammer drills, highlighting the range of emission values that can be obtained for a tool. Data from many other tool types are also included in the database. Methods Tri-axial hand-arm vibration was measured at both handles of each of 19 electrical hammer drills, in accordance with ISO 5349-1 (2001). Each tool was measured with three experienced operators and at least 5 runs were completed for each operator. Tools were tested using a range of appropriate new bits from 4 to 40 mm diameter. The minimum number of bits for a tool was 3; the maximum number was 29. 146 tool / bit combinations are reported here, representing about 2200 individual 6-axis measurements. Operators were required to drill vertically into a concrete block with a compressive strength after 28 days of 40 N/mm². Two drills (1 and 15) were battery powered; others were powered using a 110V transformer supply.

Jan 6, 2006

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933