Search Documents

By W. J. Kroll

This report is concerned with the many sidelines that were investigated incidental to developing a process to produce ductile Zirconium by members of the staff of the Bureau of Mines laboratory, Albany, Oreg. The results of the main investigation, concerning the production of malleable zirconium by reduction of chloride with fused magnesium under helium, have been described in previous publications. These should be taken as a background to facilitate understanding of this work. Literature on the metallurgy of zirconium has been summarized in a separate publication (2), and references are given in this report only when new publications have to be considered or old ones stressed. Most of the observations described in this report can be applied to the problems involved in making titanium with virtually no change. In general, titanium is easier to reduce than zirconium, since its affinities are lower. Also, its chloride is easier to handle and keep clean because it is a liquid at room temperature.

Jan 1, 1952

By Thomas L. Vandergrift

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This U.S. Bureau of Mines study examines theoretical and practical aspects of rock pres¬surization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening; and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Jan 1, 2010

By L. M. Burman

The phase-boundary pressure required to maintain a natural hydrocarbon fluid in a single phase must be considered in planning the recovery of reservoir liquids by miscible-phase processes. The change in the phase-boundary pressure at reservoir temperature that results when a light component or a mixture of light components is added to a reservoir fluid is an especially important consideration. The cricondenbar pressure (maximum phase-boundary pressure) and the critical pressure are unique correlated pressures that have been utilized to calculate the change in phase-boundary pressure that may result when the composition of a reservoir liquid is altered by an additive. In this study one reservoir oil and three gas-condensate fluids are used as examples. Correlations pertaining to the critical and cricondenbar states in chapters 4 and 5 of Bureau of Mines Monograph 10 (3)5 were used to demonstrate how butane and lighter components added to these reservoir fluids affect their phase-boundary pressures.

Jan 1, 1962

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By Raja V. Rarnani, Robert L. Frantz

"The more than 75 research projects funded throughout the first 10 years of the Dust Center's operation have resulted in numerous cumulative findings fulfilling the goals of the Center. These project descriptions present the methodologies and project-to-project relationships leading to their various accomplishments and demonstrate the mesh between project objectives and Center goals.To develop equipment for collecting respirable dust samples.To develop experimental methods for particle-by-particle characterization of morphology, size, and chemistry.To develop experimental methods for overall respirable dust sample characterization of size distribution, chemistry, and crystallography.The project directly addresses the Center's goals to enhance the understanding of the scientific and engineering characteristics of fine and respirable mineral particles found in mining and milling atmospheres and to establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment, and control measures) in the generation of fine particles. The project also aims to contribute to the development of control mechanisms for reducing ambient respirable dust concentrations and worker exposures.The work on this project is related to similar work on Coal Mine Dust Characterization (Project No. 2701/MN1) and Characterization of Dust Particles (Project No. 4203/PS3).Airborne dust sampling was performed at the following locations: 1) a sand and gravel quarry in Southern New Hampshire, 2) a welding facility, 3) a ceramic powder facility, 4) a metal powder facility, and 5) the air in Cambridge, Massachusetts. A portable sampling box incorporating two Sierra personal cascade impactors was designed and produced. At a 2-LPM flow rate, the effective cut-off diameters of the Sierra impactors were 10.0, 6.0, 3.5, 2.0, 0.9, and 0.5 mm, respectively, for each stage, and the air passed through a PVC filter after the last stage. In addition, the sampling box contained a total respirable dust filter. The substrates were weighed carefully before and after collection, and the weight increases were recorded. All films, foils, and filters were put in the balance chamber for more than 8 hours to stabilize the temperature and humidity before weighing. A Cash 21 microbalance (±0.001 mg) was used to weigh the Mylar films, SS films, and filters."

Jan 1, 1995

By Stephen D. Cramer

The objective of the present studies was to develop thick adherent and coherent coatings of platinum and palladium on refractory metals and other substrates of industrial and engineering importance. Existing platinum and palladium electrolytes were modified to make them suitable for the electrodeposition of thick deposits. The optimum operating conditions for these electrolytes were established. Pretreatment procedures for columbium, copper, graphite, molybdenum, nickel, stainless steel, tantalum, titanium, tungsten, vanadium, and zirconium substrates were studied. New pretreatment procedures for columbium, molybdenum, stainless steel, tantalum, tungsten, and nickel were developed. The internal stress and hardness of selected electrodeposits were measured. The effects of heat treatment upon the properties of electrodeposits were studied.

Jan 1, 1967

By W. F. Marshall

This report describes exhaust-emission data from 10 diesel engines: six 4-cycle, direct-injection, naturally aspirated engines; two 4-cycle, direct-injection, turbocharged engines; one 4-cycle, precombustion-chamber, turbo-charged engine; and one 2-cycle, direct-injection engine. These engines were tested over a 3-year period (1968-70). Lowest emissions were obtained with a precombustion-chamber engine. Emissions from the 2-cycle, direct-injection engine fell within the range of emission rates for the 4-cycle, naturally aspirated, direct-injection engines. Excluding the precombustion-chamber engine and excepting one of the 4-cycle, naturally aspirated engines, carbon monoxide emission rates were about the same for all engines tested. Test data on smoke, odor, and emissions of hydrocarbons, oxides of nitro-gen, carbon monoxide, and aldehydes are given.

Jan 1, 1971

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By J. A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since the early 1980's, the U.S. Bureau of Mines has conducted numerous studies in underground and surface coal mines to identify the sources of quartz dust and its fundamental characteristics. This report presents data and conclusions obtained from these studies. The two most significant quartz dust sources were found to be the continuous miner excavating rock and the highwall drill operating in a rock overburden. The percentage of quartz was found to be higher in the smaller size fractions of dust when significant amounts of rock were mined by the continuous miner. Another factor theorized to affect quartz dust generation and size characteristics is the morphology of the quartz-bearing rock. Several laboratory studies were conducted to investigate capture efficiency of water spray technology and flooded-bed scrubbers with respect to the particle size of the dust. Water sprays and flooded-bed scrubbers were both found to be less efficient on smaller dust particles, and the scrubber was particularly less efficient on quartz dust. These results indicate that quartz control technology should be directed at controlling smaller sized dust particles.

Jan 1, 1990

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

By J. R. Thoenen

The enormous and constantly increasing demand for limestone to supply a multitude of uses is a remarkable feature of the mineral industries. As approximately 130,000,000 tons of limestone are produced annually, it is not surprising that deposits at or near the surface are gradually being exhausted and that less advantageous supplies are being worked. Quarries are becoming deeper and wider year by year, and in many places the volume of overburden that must be removed to allow open-pit work has increased alarmingly. Quarrymen are also gradually learning how expensive it is to sort and clean stone from a deposit overlain by poor material. As such conditions confront the limestone industry, the natural tendency is to seek some modification in method whereby the handicaps of increasing cost may be met and overcome. Operators, some of them unwillingly, have been forced to conclude that underground work in drifts and tunnels is the most logical solution of the problem. The unwillingness of some is largely due to unfamiliarity with mining and to the unfounded fear that costs must increase and dangers multiply when mining is undertaken.

Jan 1, 1926

By R. J. Leary

A small electronic digital computer employing punched cards has been used to facilitate the solution of a variety of problems in Bureau of Mines pyrometallurgical research. In this work the computer has been found to be economical for solving both simple problems that occur repeatedly and those involving complex or iterative calculations. Each of these classes of problems and their respective solutions are described. These small computers can be used effectively by researchers when they work in consultation with a computer specialist. Close team work produces the required solutions in less time, and, oftentimes, in a more useful form. Participation in programming by researchers develops in them a skill for evaluating the suitability of problems for electronic computing.

Jan 1, 1960

By M. R. Geer

The widespread adoption during the past decade of the dense-medium process for cleaning coal increases the need for technologic studies of the process. Such studies provide information that will insure maximum usefulness of this process in its present form and may well lead to substantial improvements in design and opera¬tion. The Bureau of Mines has published the results of cleaning trials on a wide variety of coals in two dense-medium pilot plants5/ and reported the recovery of coal from waste by dense-medium treatment.6./ The present report deals with the viscosity of magnetite dense medium, an important subject about which virtually nothing has been published. Specifically, the report concerns methods for measuring viscosity, the influence of various medium contaminants on viscosity, the effect of viscosity on cleaning results, and the influence of viscosity on consumption of medium. Cleaning trials on four coals of varied density composition in a pilot plant, using mediums of different viscosities, showed a steady reduction in cleaning efficiency with increasing viscosity in every instance. However, the behavior of each coal in a viscous medium was distinctly individual. With one, an increase of only 1 centipoise in viscosity caused a reduction in recovery efficiency of 7.7 percent, whereas the same increase in viscosity with another reduced recovery efficiency only 2.7 percent.

Jan 1, 1957

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

As part of remote sensing research on an abandoned mine lands (AML) site in the Colorado Springs, Colorado area, a geographic information system (GIS) database was generated. This GIS database contains information on the locations and extents of abandoned underground coal mines, the geology of the area, subsidence features and degrees of subsidence risk, topography, drill hole locations, and lineaments (linear features) related to subsurface geologic structures. A GIS database allows the reproducible and accurate comparison and analysis of any data sets which geographically overlap and are within the same coordinate system. The database has been released to the public domain so that government agencies, researchers, educators, and the general public can access this coherent database for the purposes of better understanding the study area and GIS technology. Data files and maps are available in formats that are compatible with the GIS software used in the research project and with most CAD systems so that as many people as possible can make use of the majority of the database. This document serves as the data dictionary for the database by providing descriptions and origins of the data files.

Jan 1, 1992

An independent contractor is defined by the Mine Safety and Health Administration (MSHA) as ?any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine.? Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines. Companies In 2007, a total of 2,999 contracting companies reported employment at coal mines to MSHA, or 35.7% of all independent contracting companies.

Aug 1, 2009

By A. W. Decora

Gas-liquid chromatography has been applied to separating basic nitrogen compounds, such as pyridines and amines. Close-boiling compounds have been separated by exploiting structural and polarity differences, using selective liquid substrates dispersed on specially prepared solid supports. Development of these special supports was necessary in order to obtain symmetric peaks for basic nitrogen compounds; solution of this problem was important in applying gas-liquid chromatography to the analysis of basic nitrogen compounds found in shale oil. Attempts to analyze shale-oil tar bases by conventional gas-liquid chromatographic techniques, using Chromosorb4/ or Celite 545 as the support for a nonpolar liquid substrate, resulted in asymmetric peaks. These asymmetries were caused by adsorption of sample vapors on the solid support. Symmetric peaks were obtained when strongly polar liquid substrates were used on either Chromosorb or Celite. However, a solid support giving symmetric peaks only with strong polar substrates restricts the choice of substrate, and frequently, desired separations cannot be achieved.

Jan 1, 1961

Objective To identify techniques to reduce the probability of gob gas explosions. Background In the last 6 years, seven explosions of methane and/or coal dust occurred within worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many mine seals and caused much damage external to the sealed area. Three of these gob gas explosions occurred in one mine in Alabama over a 3-year period. Fortunately, the explosion forces and the toxic gases that vented from the sealed gob area did not cause fatalities or injuries, but they destroyed several large seals. If miners had been inspecting or working near these areas, the potential for serious injury and/or death would have been high. The United Mine Workers of America and the Mine Safety and Health Administration (MSHA) requested that the National Institute for Occupational Safety and Health (NIOSH) help identify the mechanisms for lightning penetration into the gob and recommend ways to reduce the probability of occurrence of future explosions from such lightning penetrations into sealed areas of underground coal mines. Because three of the explosions occurred in a single mine, special attention was focused on these particular explosions. The first occurred in April 1994 in a sealed area, which enclosed about 1.35square miles of abandoned workings (gob). This explosion destroyed 3 of the 38 seals that surrounded the gob. These seals were less than 2,000 ft away from three 4.5-in-diam steel-cased test wells that extended from the surface into the mine entry. At the time of the explosion, the National Lightning Detection Network (NLDN)verified 12 lightning strikes within 10 miles of the mine, including several above the gob. After the 1994 explosion, the damaged seals were rebuilt using an acceptable seal design capable of with standing a 20-psi explosion, as required by 30 CFR 75.335. On January 26,1996, a second gob explosion destroyed five more cementitious pumpable seals less than 2,000 ft away from those destroyed in 1994and even closer to the steel-cased wells. The NLDN verified72 lightning strikes in the area of this second gob explosion. Compressive strength analyses of fragments from the destroyed seals showed that strengths ranged from 11 to 138 psi, with an average of83 psi. This is over 100 psi below the minimum 200-psi compressive strength requirement for cementitious pumpable seals. These seals were again replaced. On July 9, 1997, the third and most violent explosion occurred in the same vicinity of the last two explosions. Three more cementitious pumpable seals were destroyed, including one newer seal that exceeded the minimum 200-psi compressive strength requirement. The NLDN verified 695 lightning strikes above the mine during the time in which the explosion occurred. MSHA's

May 1, 2001