Search Documents

By Raja V. Ramani, Wilson Miola

"The potential health effects of quartz-bearing airborne dust in mine and mill atmospheres point to the need for the quantification of quartz content in the source material for determining the source-sink relationships and for choosing applicable control measures. While a standard method exists from a regulatory point of view for the sampling of coal mine atmospheres for determining (i) respirable dust concentrations and (ii) the amount of quartz in the samples, there is no generally accepted standard method for quartz analysis in bulk samples of coal and host rocks. Generally, the bulk sample is reduced to a powder for producing quartz analysis samples. Extensive controls arc necessary to ensure representativeness of the analysis samples when these are very minute fractions of the bulk samples. Since the amount of analysis sample is not limited, alternative methods for quartz analysis may also be tried. It is, however, necessary to adopt a procedure which will satisfy several statistical requirements to guarantee representativeness of the quartz analysis samples.In this paper, the important factors in the preparation of quartz analysis samples from the host rocks and bulk samples are discussed. The method developed to prepare the analysis samples is outlined. The results of application of the procedures are presented. The procedure developed for quartz analysis sample preparation is based on sound statistical foundations. The procedure has been validated for reproducibility and homogeneity.The current methods used for quartz analysis in powders are the P-7 infrared spectrometry and quantitative X-Ray Diffraction (XRD). Both have similar restrictions concerning the sample characteristics and operational problems, which arc intrinsic to radiation beams, device geometry, mechanics and controls of the radiation behavior. Although improvements can be made in the spectrometers and diffractometers, some of the most important steps are the procedures for analysis sample preparation from bulk samples and for calibration of the instruments. The sample preparation process is often referred to as one of grinding and sizing the bulk sample to generate the powder for the scanning devices. The particle sizes are referred to and their influence emphasized but the representativeness of the sample is assumed. Assuring sample representativeness during the sample preparation procedures is critical.For the sampling of airborne respirable dust in coal mines, the collection devices, the collection procedures and the analysis procedures are defined. This is not true for bulk samples where weights must be reduced thousands of times to generate the analysis samples for the scanning devices. The specifications to be developed may include bulk sample amount, sample reduction procedures, sample particle size distribution and sample amounts. However, the common problem of insufficient sample amount which is often encountered with mine airborne dust samples need not exist for bulk samples. Further, the same bulk sample can yield analysis samples for several experiments. The latter, of course, requires sample homogeneity.Three concepts are important in the selection of any procedure for sample preparation and analysis. These arc accuracy, reproducibility and representativeness. The adopted procedure has to guarantee a homogeneous sample representative of the population, a defined level of accuracy and reproducibility. Important statistical concepts are embedded in these requirements, particularly with respect to estimation and dispersion errors. Accuracy and reproducibility are totally different though not independent concepts. Estimation is related to accuracy and the true value. Dispersion is related to reproducibility and is measured by the classical statistical standard deviation of the distribution of a series of measurements or analysis performed over the same lot or analysis sample. The dispersion variance (or dispersion error) does not tell a"

Mar 1, 1992

By William H. Schiffbauer, Ph. D. Mowrey

Proximity warning devices can improve workplace safety by alerting workers when they are in a hazardous area near moving equipment. Industrial work sites often present extreme challenges to safety-based proximity warning devices. Many commercially available types of proximity warning sensors and systems can be rendered useless when covered with mud, ice, snow, ore, rock, and other material. The list includes radar, ultrasonic, capacitive, and visual types of sensors and systems. Addressing these shortcomings, NIOSH personnel have developed a patented active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) which employs lowfrequency, low-power magnetic fields which are quite impervious to severe environmental conditions. A shapeable wire loop antenna which provides the marker of dangerous work areas, has been mounted on a continuous mining machine and was mounted inside 1.3-cm thick angle iron. This loop antenna was exposed to more than six months of active underground coal production, which included being covered by and scraped over with tons of rock, sprayed by a continuous stream of water, and immersed in thick mud. After six months the loop antenna showed signs of wear, but was still capable of performing its intended function. The HASARD system is now being applied to other industrial applications and is showing much promise, especially in harsh environments. This paper details the system, describes the tests that have been done, and mentions other areas where it can benefit the safety of industrial workers.

By Charles E. McCarthy

Part 1 of this report is concerned with the electric-furnace production of calcium aluminate and iron alloy from a variety of siliceous ferruginous ores of aluminum. The furnacing research was directed, first, to determine the extent of the field in the CaO-Al2O3-SiO2 system, in which calcium aluminates with the optimum leaching characteristics are obtained; second, to produce suitable quantities of these aluminate mixtures for pilot-plant leaching tests; third, to investigate the physical chemistry of the reduction reactions during furnacing; and, fourth, to study the economics of the process. The third and fourth steps were not completed. Part 2 comprises another phase of the work and will appear as a second Report of Investigations. It deals with the extraction of metallurgical-grade alumina from the calcium aluminate slag produced in the electric furnace and includes the following steps: leaching, desilicating, precipitating, dewatering, filtering, and washing of the aluminum hydrate. No claim is made that the data are complete, nor has the chronological order of obtaining data been followed. Rather, it is emphasized that additional work is necessary if the full possibilities of the process are to be evaluated. and made available.

Jan 1, 1949

By J. Hyvarinen, A. D. Look

"INTRODUCTION AND SUMMARYElectricity is used extensively in open-pit metal mines to provide illumination, heat, and power to operate hauling and loading equipment, drills, pumps, signal systems, and other machinery. Good installation and maintenance of equipment and power, circuits, are essential to minimize the hazards of shock, burns, and fire.In the 13 years from 1931 to 1943, 20 fatal and 82 nonfatal injuries resulted from the use of electricity in open-pit mines in the United States ; 4/ these figures represent about, 10 percent of all fatalities and 1 percent of the nonfatal injuries. The ratio of fatal to nonfatal injuries from electricity in such mines was very high during this period; the figures show one fatality to every five accidents from this cause.Electricity may cause personal injury through abnormalities in equipment, such as short-circuit, accidental ground, overload, and poor contact; however, each year some fatal electrical accidents are due to persons touching uninsulated ""live wires."" These contact injuries are the result of careless body movements of persons in the vicinity of 'wires at places not normally frequented, or of accidental contact with live circuits when handling metal objects. Electrical hazards can be minimized by the enclosure or elevation of current-carrying parts; ample working space around equipment, adequate insulation, locking switches in the open or closed position under certain conditions, identifying and warning devices, protective grounding, insulating flooring, platforms, or rubber gloves, and proper inspection and maintenance."

Apr 1, 1949

By I. F. Avery

The productive capacity of natural-gasoline and cycling plants in the United States on January 1, 1958, was 48.8 million gallons per day, according to the Bureau of Mines biennial survey. This represented an increase of 2.4 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 7.5 million gallons per day. The major increase in operating capacity occurred in Texas and New Mexico. In New Mexico, capacity increased 43 percent. The total number of plants decreased from 600 on January 1, 1956, to 584 on January 1, 1958. The number of operating plants decreased from 571 to 558. Five new plants were completed in Colorado, increasing the number of operating plants from 7 to 12.

Jan 1, 1958

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By R. V. Ramani, R. Bhaskar

"The National Academy of Sciences (1) recognized the importance of studying the spatial and temporal characteristics of respirable coal mine dust atmospheres. In this paper, the progress to date of a research project on dust transportation and deposition in mine airways is presented. A mathematical model is proposed for studying the transport of dust. A source representative of dust generation in underground coal mining is defined. The influence and applicability of surface roughness, dispersivities, coagulation and reentrainment to vine dust flow arc examined. A convective-diffusion model is proposed for the transport and deposition of dust in mine airways. Using the model, the spatial and temporal characteristics can be evaluated in terms of dust concentrations in the mine atmospheres.INTRODUCTIONThe prediction of the behavior of fine particles Is Important in many fields of science and engi¬neering including physics, chemistry, mining, mineral processing, and atmospheric science. In mining from the health point of view, fine coal dust is associated with the appearance of pneumoconiosis in miners exposed to the dust. Also, in addition to being a nuisance factor obscuring visibility and general mobility of miners, it can lead to sudden catastrophic incidences of explosions. This paper outlines the progress to date of a research project on dust transportation and deposition in mine airways. A mathematical model is proposed for studying the transport of dust for the various mechanisms. The dust dispersion is defined in terms of a dispersion term determined from experimental data by Skubunov (23). Coagulation is considered as one of the mechanisms that can lead to changes in the particle size distribution. Reentrainment as a possible secondary source of dust was examined during model development but was not included in the final model."

Jan 1, 1988

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

In 2007, a total of 14,871 mining operations reported employment data to the Mine Safety and Health Administration (MSHA).1 Almost half (48.4%) were sand and gravel mines, followed by stone mines (31.2%), coal mines (13.7%), nonmetal mines (4.9%), and metal mines (1.9%).

Aug 1, 2009

By M. Howard Berliner

In August 1943 the Bureau of Mines completed seven churn-drill holes in an area of old mine workings near Linden, Wis., formerly known as the Argall mine. The work was undertaken as part of a general investigation by the Bureau of the zinc and lead producing area of southwestern Wisconsin at a time when special effort was being made to increase the production of metals necessary for war. The area was selected for investigation on the basis of its favorable geologic structure, past history, and apparent mineralization.

Jan 1, 1948

By M. Hertzberg

The Bureau of Mines measured the energy requirements for the spark ig-nition in air of Pittsburgh seam bituminous coal dust, lycopodium spores, and polyethylene powder with a 1.2-L furnace and 8-L and 20-L chambers. Thermal autoignition temperatures of the same dusts were mea-sured in the 1.2-L furnace. Electrical ignition requirements are given in terms of both effective spark gap energies, [ ] and stored circuit energies, 1/2 CE2. The measured order of electrical ignitability for the three dusts is consistent with the data of other researchers; however, the absolute values are systematically higher, probably because of higher flow and turbulence levels in the chambers used and lower electrical efficiency in the circuit used here. The temperature dependence of the lean limit of flammability for lyco-podium was measured wi th the 1.2-L sys tem, and those measurements con--firm the applicability of the modified Burgess-Wheeler law to a dust. Due to experimental complexities, the minimum ignition energies for dusts may not reflect intrinsic flammability behavior. However, some valuable information may be obtained from the relative ignition energies of various dusts at ambient and elevated temperatures. In addition, the concept of minimum electrical ignition energies for homogeneous gas mixtures is reevaluated theoretically.

Jan 1, 1985

By Paul H. Mutschler

The Bureau of Mines sponsored a study of the impact of changing technology on the demand for metallurgical coal and coke to 1985. Individual technologies were analyzed to determine what effect each had on the demand for and the consequent consumption of metallurgical coal and coke in the steel industry. The domestic steel industry demand for metallurgical coal and coke for the production of hot metal will probably increase through 1985. Formcoke if implemented on a worldwide basis could begin to supplant the U.S. export market for metallurgical coal. The major technologies that have contributed to the decline in demand for metallurgical coke per ton of hot metal are (1) the increased usage coupled with higher iron content of agglomerates, (2) modification of blast furnace practices such as high top pressures and blast temperatures, and (3) increases in the injection of supplemental fuels. The projected demand for metallurgical coal and coke under current technology for 1985 are 109.4 and 76.0 million tons, respectively. With future technology implemented, the demand for metallurgical coal and coke will be 82.0 and 56.9 million tons, respectively. The projected domestic demand for metallurgical coke could further decrease by as much as 15 to 20 million tons by 1985 if formcoking proves technologically and economically feasible.

Jan 1, 1975

By W. D. Riley

The U.S. Department of the Interior, Bureau of Mines, has been conducting minerals recovery research in support of the nation&apos;s geothermal program since 1974. The Bureau&apos;s program of laboratory and field studies has focused on determining the materials of construction for geothermal resource recovery plants and an the recovery of mineral values from the geobrines. An analytical program has been conducted at the Avondale Research Center to determine the chemical constituents of some high- and low-salinity geobrines found in the Imperial, Valley of California. Data are reported for the early stages of brine production of femur geothermal wells--the low-salinity, medium-enthalpy brines from the East Mesa Known Geothermal Resource Area (KGRA), Mesa 6-1 and 6-2, and the high-salinity, high-enthalpy brine from the Salton Sea KGRA, Magmamax 1 and Woolsey 1. The reported results indicate the importance of the operating and engineering history, the operating parameters during sampling, and the method of sampling in order to evaluate the chemical analyses.

Jan 1, 1980

By Clarence O. Babcock

This report describes the results of Bureau of Mines laboratory and preliminary field tests on a rock bolt of helical shape. The flexible construction allows the bolt to maintain a more stable load level than is possible with a straight bolt. Bolt load changes resulting from anchor slippage, blasting shock, or changes in mine geometry with mining advance are minimized. Preliminary field tests were performed at the Kaiser Steel York Canyon mine where the load changes of straight and helical bolts were measured using a vibrating-wire load gage. The field tests were performed to establish the viability of the concept of a helical bolt. The practical usefulness in terms of performance and economics remains to be shown. The change in bolt load for the flexible bolts was one-third that for the straight bolts. There were no malfunctions of the gage, and the bolts maintained a more uniform load than the straight bolts used as controls.

Jan 1, 1978

By Gwendolyn D. Hood

The U.S. Bureau of Mines developed a dewatering technique for treating wastewater that was tested on waste slurry from a commercial tile company in Alabama. Raw wastewater samples were pretreated with 10 Ib calcium chloride and 10 lb Wyoming bentonite per 1,000 gal of slurry. After pretreatment, polyethylene oxide (PEO) at dosages varying from 0.05 to 0.20 lb per 1,000 gal was mixed with the waste slurry, forming strong, tough floes that were separated from the clarified water using a trammel. The flocculated slurry was dewatered to a consistency that could be handled for subsequent disposal in a landfill. The clarified water quality was equivalent to that of the company&apos;s present treatment system.

Jan 1, 2010

By T. A. Sullivan

The Bureau of Mines investigated modified sulfur concretes as one part of a program for utilizing sulfur in construction materials. The use of modified sulfur was studied as a means of preventing the stressing action in the concretes caused by the allotropic transformation of sulfur on solidification. Unmodified sulfur concretes have been prepared that have compression, flexural, and tensile strengths equivalent or better than Portland concretes. However, most of these concretes have been vulnerable to deterioration by weathering, temperature fluctuations, and freeze-thaw cycling. The sulfur was modified by reaction with dicyclopentadiene or dipentene before use as an aggregate binder. Sulfur concretes and modified sulfur concretes were pre-pared from acidic and basic type aggregates. Physical properties of the optimum mixtures were determined and compared with each other and with Portland cement concretes. The best results were obtained by reacting sulfur with 5 pct dicyclopentadiene to prepare modified sulfur concretes. Field testing of the concretes are in progress. Present results show that modified sulfur concretes are superior to unmodified sulfur concretes and equal or better than Portland concretes in compressive, flexural, and tensile strengths. Long-term aging characteristics of both modified and unmodified sulfur concretes are being determined.

Jan 1, 1976

By Brinton C. Brown

This paper describes the methods and equipment developed at the Bureau&apos;s Experimental Oil-Shale mine near Rifle, Colo., for placing men in position to scale loose rock from the walls, pillars, and roofs of high stopes or rooms. The equipment developed at Rifle has application not only in oil-shale mining but in most of the country&apos;s underground limestone mines and in the exploitation of other mineral deposits mined in high stopes by room-and-pillar methods. Equipment in use at Rifle includes: 1. A boom-type scaling rig with a self-leveling platform constructed on a small "cat"-mounted crane. Men working from the platform on this machine can efficiently scale mine walls and roofs 27 feet above the floor. 2. A conventional fork-lift truck modified to provide a remotely controlled working platform from which men can scale to heights 27 feet above the mine floor. The platform on this unit is larger than on the boom-type rig and allows the men to inspect larger areas of the mine wall from a single setting of the machine. 3. A third rig, consisting essentially of a platform mounted on a tele-scoping tower, designed and built to elevate men 65 feet above the mine floor. Versatility of this machine permits men to work from the platform at heights of 5 to 65 feet. In the operating position, the unit requires a minimum clearance of 25 feet. In the nonoperating position the tower of the machine folds to an over-all height of 15 feet 10 inches to permit travel through haulageways. 4. An industrial gun, lightweight scaling bars, and mechanical scalers, which have been tried for removing loose rock from the mine walls with varying degrees of success.

Jan 1, 1950