Search Documents

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By Richard L. Rains

In 1984 and 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 162,887-acre Mormon Mountains Wilderness Study Area (NV-050-161) in order to evaluate its identified mineral resources. The study area is located in Lincoln County, NV, about 60 miles northeast of Las Vegas. The study area had no mines or mining claims in 1985, and no mineral resources were identified within the study area, or at the Whitmore mine or Iron Blossom prospect near the study area. The alluvial fans around the southern boundary are staked with about 450 placer claims. Chemical analyses of samples indicate that some limestone in the study area is suitable for manufacturing cement or for agricultural purposes but the limestone is distant from markets and therefore not economic in the foreseeable future. The study area is blanketed with oil and gas leases, but no known productive horizons were identified.

Jan 1, 1986

By John E. Pahlman

The Bureau of Mines has conducted research on a dual leaching method that offers the potential for the economic recovery of the silver, as well as of the manganese, contained in some domestic manganiferous silver deposits. The method consists of an initial leach of manganese with aqueous sulfur dioxide (S02) followed first by a neutralization rinse, and then by a second leach with cyanide solution for the extraction of silver. Refractory silver in these ores was either (1) intimately associated with the manganese, (2) chemically resistant to cyanide leaching, or (3) rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when minus 2.5-plus 1.3-cm ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct of the silver and 65 to 96 pet of the manganese were attained in laboratory column-leach tests using the dual leaching method on equivalent-sized ore pieces from seven domestic deposits.

Jan 1, 1987

By Paul Hatmaker

Diatomite is the name now generally given to a mineral substance composed of the tiny , skeletal remains of diatoms , which are microscopic , flowerless , water plants related to the algae ... This residuum is essentially hydrous amorphous silica. Common names for diatomite are : Diatomaceous earth , tripolite , kieselguhr , and infusorial earth . Strictly speaking , however , the latter material is not diatomite , as it is composed of the fossil remains of infusoria , which usually do not occur with the diatomaceae . Other synonyms for diatomite are : Diatomaceous silica , kieselmehl , bergmehl , diatomeenpeelite , polirschiefer , moler , molera , molererde , de smid earth , fossil flour , mountain flour , farine fossil , white peat , radiolarian earth , chalk rock, ceyssatite , randanite , and tellurine ; also various diatomite products of individual companies are known by their own trade names . Diatomite should not be confused with fuller's earth , for the two are separate and distinct substances . Bentonite , pumice , and tripoli , have also been used erroneously to designate diatomite . Tripolite , however , is a true diatomite formerly mined near Tripoli ..

Feb 1, 1931

By C. W. Sill

[In the original Norris and Fay method for determining selenium, selenious acid is reduced by an excess of standard thicsulfate in accordance with the following reaction: H2Se03 + 4Na2S203 + 4HC1 = Na2SeS406 + Na2S406 + 4NaC1 + X20. (1) The excess thiosutfate is then back-titrated with standard iodine solution. The disadvantages of ouch a method are obvious. On an unknown sample, the quantity of thiosutfate required would be difficult to determine; a definite excess is required, but large back titrations would be undesirable. Inasmuch as thiosulfate is decomposed by acid, considerable error may be introduced in this method, the amount depending on the acidity, temperature, concentration of excess thiosulfate, duration of contact between thiosulfate and acid, and other factors, In a critical study of the Norris and Fay method, Coleman and McCrosky3/ show that the method is accurate to less than .1 part per thousand if the excess of this sulfate Is not greater than 5 ml. of 0.1 N solution (in 1.0 ml. of 0.x4 N sulfuric acid) whether the titration is made at 0° or 20°C. A greater excess produced unsatisfactory values at either temperature. Coleman and McCrosky regulated the excess thiosulfate by adding 5-ml. portions of thiosulfate solution followed by the addition of 1 to 3 drops of 2.5 percent potassium iodide in the presence of starch. If a starch-iodine blue color formed locally around the drops of potassium Iodide, the reduction of selenious acid was not complete. On stirring the solution, the local blue color fades and another 5-ml. portion of thiosulfate is added. When addition of potassium iodide fails to produce a local blue color, reduction of selenious acid is complete, and the excess thiosulfate is then back-titrated with standard Iodine solution. The number of equivalents involved in the reduction of selenious acid by either thiosulfate or iodide is the same, and therefore no correction need be made for the potassium iodide. This procedure is much better than the original Norris-Fay titration, but acidity and time would stilt be rather critical factors subject to variation with individual technique. Also, the method still requires the lose of two standard solutions, a rather undesirable factor from the standpoint of routine application.]

Jan 1, 1954

By A. Wahab Khair, N. P. Reddy

"INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982).One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Morgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cytotoxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le Roux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly. Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield, 1984) while Dodgson, et. al., (1971) concluded that high exposures to minerals such as illite, kaolinite and mica will retard the progress of CWP. Size and shape characteristics are believed to be important in the relationship between mineral particles and health effects (Shedd, Virta and Wylie, 1982)."

Mar 1, 1989

By G. W. Jones

[A survey of the literature relating to ignition temperatures of acetylene-air and acetylene-oxygen mixtures reveals rather wide disagreement in the reported results. In some instances the ignition temperatures of acetylene-air mixtures were reported to be lower then those of acetylene-oxygen mixtures, which is contrary to experience with other combustibles. To clear up some of the reported discrepancies, the authors have investigated the ignition temperatures of acetylene both in air and oxygen, and their results are presented in this report.]

Jan 1, 1941

By M. R. Peterson

The U.S. Bureau of Mines investigated column flotation for recovery of a high-grade fluorite (CaF2) concentrate and byproduct concentrates from the Fish Creek fluorite deposit in Eureka County, NY. The recovery scheme consisted of (1) grinding the ore to minus 48 mesh, (2) fluorite rougher and cleaner flotation, (3) desliming the rougher fluorite flotation tailings at 20 Jjm, (4) mica flotation, and (5) silicate rougher flotation. Acid-grade fluorspar, mica, free silica (Si02) sand, and low-grade beryl (Be3Al2S~018) concentrate were produced in a 100 lb/h continuous column flotation unit (CCFU). The highest results achieved were %.6-pct CaF2 recovery in a fIrst cleaner concentrate containing 99.7 pct CaF2. Beryl recovery was as high as 92 pct at a grade of 5.3 pct BeO. The silica sand, which assayed 98 pct Si02, was recovered as the rougher beryl flotation tailings. Collector reagent consumption was reduced 45 pct for fluorite and 58 pet for silicate flotation in comparison with bench-scale conventional flotation. All products were signillcantly improved in both grade and recovery over conventional flotation results, and the recovery scheme was simplifIed by removal of several stages of flotation in the fluorite and silicate flotation steps.

Jan 1, 1990

By Richard L. D?Arcy

This paper describing the mining practice and methods at the United Verde Extension mine, Jerome, Ariz., is one of a series of papers in preparation by the Bureau of Mines presenting the mining methods used in various mining districts of the United States. The United Verde Extension mine is a massive, high-grade deposit of copper sulphide containing some gold and silver and is mined almost exclusively by the conventional square-set method with some local modifications. About 450 men are employed underground and 1200 tons of direct smelting ore is produced per day. Figure 1 is a surface map of the Jerome district.

Jan 1, 1930

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961

By F. N. Kissell, C. H. Elder, C. M. McCulloch

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By Warren D. Longwill

All known resources within the four proposed RARE II additions to the Yolla Bolly-Middle Eel Wilderness in northwestern California occur in the Gig Butte-Shinbone study area (fig. 1). No mineral resources are Figure 1.--NEAR HERE. known in the East Fork, Murphy blade, or Wilderness Contiguous units. About 2,400 tons (2,177 t) of subeconomic manganese resources averaging 9.5 percent manganese have been estimated at the Blue Jay Mine in the Big Butte-Shinbone unit. In addition about 9,700 tons (8,793 t) of subeconomic chromium-nickel-cobalt resources in thin laterite soil at the Grubstake Prospect contain about 1.27 percent chromium oxide, 0.45 percent nickel, and 0.03 percent cobalt. Adjacent Ultramafic rock outcrops have pods averaging 2.5 percent chromium oxide (Cr203); one pod contains about 40 tons (36 t) of indicated subeconomic resources.

Jan 1, 1981

By Sathit Tandanand

Horizontal displacements and ground strains induced by mine subsidence are significant information needed for calculating damage and developing precautions against subsidence effects on surface structures. To devise a simple method for determining the surface horizonal displacements and strains simultaneously with the subsidence prediction, the U.S. Bureau of Mines examined the significance of the tilt number, which is the proportionality constant in the relationship between the horizontal displacement and the slope of the subsidence profile. The ratio of the tilt number to the critical radius of the subsidence trough is identical to the ratio of the maximum possible horizontal displacement to the full subsidence, which is found to be constant in most European coalfields. If this ratio is known for a particular minesite in the United States, then horizontal displacement and ground strains can be readily obtained from the primary subsidence data.

Jan 1, 2010

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944

By Carl N. Anderson

This paper, which is one of a group presented by the United States Bureau of Mines covering mining practice in different districts, deals in particular with the methods employed in mining the horizontal type of zinc-lead orebodies of the West Baxter area of the Tri-State zinc and lead district. These orebodies, locally termed "sheet-ground" bodies, with their relatively low working faces and low tenor of zinc and lead, require changes in the mining practice which is used in the balance of the district. In addition to the general mining methods, this paper also describes the system of hand sorting employed prior to the direct milling of the ore. The Hartley mine is situated mile west of Baxter Springs, Kans., as indicated in Figure 1. Its general outline and the location of the shafts with respect to the milling plant are shown in Figure 2.

Jan 1, 1932

By Norman A. Pace

This paper is one of a series being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included, if available. In addition to describing equipment and methods used} the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with operation of the Camak quarry and plant of the Weston-Brooker Co. The quarry and plant are near Cedar Rock, north of State Highway No. 80 and east of Middle Creek in Warren County, Ga., and about 40 miles west of Augusta. Rail access is by a spur line of the Georgia Railroad from Camak, 5 miles southwest. The main office of the company is at Cayce, S. C.

Jan 1, 1959

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous coal, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plants; and stone quarries and their related plants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by categories: Metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (anthracite, bituminous coal including lignite, coke, petroleum and natural gas, native asphalt and related bitumens, and peat). Injury and employment data were collected from coal producers on the regular mandatory basis as required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Similar data for 1962 from metal, nonmetal (except well and brine operations), stone, and sand and gravel producers were collected by a. mandatory reporting system under the provisions of the Act of September 26, 1961, Public Law 87-300 (75 Stat. 649). Before 1962, these nonfuel producers reported voluntarily to the Bureau of Mines. Producers of all other minerals (fuel and nonfuel) reported the requested injury and employment data voluntarily to the Bureau for 1962, the same as in preceding years.

Jan 1, 1963

By ALBERT C. DURHAM

In anthracite mining , pumping is a problem of major importance , and water must be handled and rehandled in almost every mine whether the mine is in operation or idle . The motor - driven centrifugal pump is the most commonly used type of unit for the large pumping installations, and experience has . proved that fully automatic control has certain advantages over manual control . Some of these advantages are greater safety for maintenance personnel , continuous protection against faulty operation , which could cause damage to the Lumping apparatus , and lower pump -room operating costs .

Aug 1, 1948