Search Documents

By John E. Hamak

The identified helium resources of the United States were estimated by the U.S. Bureau of Mines at 617 Bcf, as of December 31, 1992. This includes 285 Bef of demonstrated reserves, 85 Bcf of demonstrated marginal reserves, and 37 Bcf of demonstrated sub-economic resources. The identified resources also include 166 Bcf of helium in inferred reserves and inferred marginal reserves and 44 Bcf in inferred sub-economic resources. The identified helium resources contained on Federal lands are approximately 172 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. Undiscovered helium resources in the United States are estimated at a most likely volume of 104 Bef, with a maximum volume of 249 Bcf and a minimum volume of 41 Bef. Also reported are 51 Bcf of helium in nonconventional and low-helium-content natural gases. Extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1992 was 3.3 Bcf. Some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1995

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7510 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. Oil and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1963

By Robert E. Wood

The temperature dependency of the low-density viscosity coefficients, ?°T, of helium and of nitrogen, 100° to 1,000° K, is correlated with empirical equations, and the temperature and composition dependencies of the low-density viscosity coefficients, ?°T, of helium-nitrogen mixtures are correlated with the Chapman-Enskog expressions by using the Lennard-Jones (6:12) potential function. The residual viscosity, ?T,P - ?°T (the difference between the viscosity of a compressed gas and the dilute gas at a given temperature), was found to be a function of the thermal pressure coefficient, (?P/?T)V, and two parameters, a and 1, which are characteristic of gas composition. The equation ?T, P = ?°T + a [(?P/?T)V]ß represented 1,340 higher pressure experimental viscosity values with a mean absolute deviation of 0.86 percent, and this equation was used to compute viscosities of the gaseous helium-nitrogen system for a range of temperatures and pressures including those encountered in Bureau of Mines helium purification processes and in a crude-helium conservation gas reservoir. Tabular viscosities for helium, nitrogen, and 13 helium-nitrogen mixtures are presented for 110 temperatures, 133° to 740' K, and 49 pressures in the range 1 to 240 atmospheres. The accuracy of the tabulated viscosities varies because correlation parameters were obtained from experimental data of unequal reliability. It is estimated that uncertainties in the computed viscosity values are ±5 percent for the region 325° to 740° K, ±2 percent for the region 183° to 325° K, and ±5 percent for temperatures below 183° K. The latter uncertainty may rise to y10 percent as critical conditions are approached.

Jan 1, 1970

By R. D. Rosenkranz

The Bureau of Mines has investigated the availability of copper from 272 deposits in market economy countries. The deposits studied have demonstrated resources totaling 413 million metric tons of contained copper and account for more than 90 pct of the reserve base for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau performed geologic, engineering, and economic evaluations in order to determine the copper production potential of each deposit. At the 1981 copper market price of $0.85/lb, the deposits studied could economically produce an estimated 88 million metric tons of copper (allowing for profit computed at a 15-pct rate of return), primarily from mines operating at the time of the study (1981). At this price, producing mines in market economy countries could economically produce only 2.1 million metric tons of refined copper per year. However, actual 1981 production was 6.2 million metric tons, indicating that many mines continued to operate even though they were unable to cover all production costs. For U.S. producing mines, the estimated average cost of production per pound (including profit at a 15-pct rate of return) was $0.15 higher than the average cost in other market economy countries.

Jan 1, 1983

By J. R. Ruark

Because of the importance of oil-shale reserves the Bureau or Mines resumed research investigations in this field beginning in 1944. The Bureau early decided to build a Large-scale demonstration plant to accomplish the dual purpose of obtaining design data and to produce crude shale oil for refining studies. Two 40-ton-Capacity batch N-T-U (Nevada-Texas-Utah) retorts were completed for this purpose in 1947. After a preliminary operation, the plant was used to investigate process variables of air rate, recycle gas rate, and shale particle size and crude. Correlations obtained from these variables are presented in this report. Researchers concluded that recycle gas was not necessary for efficient operation of the process. Short comings of the batch method of processing the oil shale are pointed out in the report. Several periods of prolonged production operations were carried out. During these periods, the retorts were operated to produce as much crude oil per day as possible. The lifetime operation of the N-T-U retorts was divides into three periods, namely, preliminary operation, process variable study, and production operation. During the preliminary operation, 187 runs were made with a total of 7,596 tons of raw shale used to produce 3,688 barrels of crude shale oil. During the process variable study, 179 runs were made with a consumption of 7,494 tons of raw shale and a production of 4,218 barrels of crude shale oil. The production operation consisted of 554 runs in which 22,457 tons of raw shale was used to produce 12,359 barrels of crude shale ail. The overall total for the lifetime operation of the retorts consisted of 920 runs with a total consumption of 37,547 tons of raw shale and a production if 20,265 barrels of crude shale oil.

Jan 1, 1956

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By A. Visnapuu

The Bureau of Mines, as a part of its goal to minimize occupational hazards associated with mining and mineral processing operations, has developed and field tested a compact exhaust air muffler for mechanized, jumbo-mounted pneumatic rock drills. The muffler is constructed of 1/8-inch sheet steel and has nominal dimensions of 1-3/4 by 9 by 13 inches. A directed air passage, flexible neoprene baffles, and an expandable slit-type outlet are incorporated to reduce drill exhaust air noise and eliminate muffler icing. Field tests in actual mining operations showed a l5-dbA reduction in exhaust noise and an 8-to 12-dbA reduction in overall drilling noise with no icing problems or decrease in drill performance. Data are presented on muffler construction, laboratory, and field test results.

Jan 1, 1979

By Arnold O. Tanner

The domestic mining industry gained more strength in 1988 as the healthy comeback that became evident in 1987 continued and grew for many commodities. The increasing and more stable commodity prices, still predominantly in the metals sector, reinforced both the new ways of conducting business and the use of technological advancements in successfully lowering operating costs during the last 4 to 6 years. Some commodities and companies still struggled to survive, but increases in productivity and profits were becoming more common.

Jan 1, 1990

By G. W. Jones

The Bureau of Mines has advocated the use of stenches as warning agents in metal mines and in gas-distribution systems since 1920 A considerable amount of research has been conducted on ethyl mercaptan and other compounds to determine their effectiveness when used for this purpose.4/5/6/7/8/9/10/11/12/13/ Miners are warned of danger by a stench injected, in measured quantity, into a compressed-air line through which it is rapidly carried to the working faces, where it escapes from the compressed-air equipment and imparts a characteristic odor to the air. This method is not applicable to mines where only a limited number of com-pressed-air lines are used, as for example, many coal mines; the ventilation currents available in these mines may be too slow for warning purposes.14/

Jan 1, 1954

By W. J. Fene

The lowest number of fatalities from coal-mine explosions in the United States in any year since records have been kept was the total of 8 in 1949 and again in 1950. Even incomplete records as far back as 1870 reveal a larger annual loss of life from explosions. From 1890 to 1948 the lowest annual loss was 32 in 1946. A smaller total of 15 fatalities was reported in 1952. Figure 1 shows the total yearly loss of life from explosions in all coal mines since 1880. Those in anthracite mines alone are shown by the shaded area. The erratic variation of the chart line shows the difficulties that have confronted the industry in the struggle to control and eliminate mine explosions. Potential hazards have existed in marry mines without realization that only a small change in conditions could initiate a disaster. Many disasters causing great loss of life occurred in mines that had been regularly operated without incident for long periods. Although the number of coal-mine explosions causing great lose of life has been kept down in recent years, the exceptions still make the record anything but satis¬factory. There have been almost no widespread explosions for several years, but in a few instances many lives were lost from afterdamp. Although the violence and spread of mine explosions may be controlled, the loss of life may be heavy if many of the men happen to be in the path of the smoke and gases. For these reasons, the strictest controls must be maintained to eliminate all factors that might combine to cause even a small ignition of gas or dust.

Jan 1, 1953

By Robert E. Manning

The Federal Coal Mine Health and Safety Act of 1969 has placed stringent limitations on the noise levels in which employees may work. This act can result in both increased labor costs because of noise-exposure time limitations and in high capital costs for modification of present equipment, and the design of new equipment, to comply with the law. The development of new noise-control systems is thus of immediate interest to industry. A current Research program at U. S. Steel is aimed at developing methods of controlling both the exhaust-air noise and the mechanical noise of a Stoper drill, a pneumatic percussive tool used for roof-bolting purposes in coal mines which has an approximate air consumption of 100 cubic feet per minute. This program is being performed under a contract between USS Engineers and Consultants, Inc. and the Pittsburgh Mining and Safety Research Center of the U. S. Bureau of Mines. In previous work at U. S. Steel, kidney-shaped mufflers were designed that wrap around the air leg of the drill for control of the exhaust noise. These mufflers were designed with the aid of a digital computer program that predicts the acoustic performance of mufflers.

Jan 1, 1975

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By H. Winkelmann

The author, who himself has worked inn the field with various types of torsion balances, expresses in the article his experience with the recently marketed Haff-Torsion-Balance. The advantages of practical work with Haff?s s torsion balance as compared with other types are mentioned. In spite of low weight and corresponding small dimensions (Model M = 23.5 kg., Model Al = 11.5 kg.) the sensitiveness is not less than that in the largest instruments. It is at 1.10-9, which is proved by calculations. A comparison with the corresponding values of other types of torsion balances (Eötvös, Askania, Gepege) is given. The mechanical features of the instrument are briefly described, and the balance is illustrated by a, cross section of it. -- W. Ayvazoglou. DETERMINATION OF THE ELEMENTS OF THE MAGNETIC AND GRAVITATIONAL FIELDS INDUCED BY AN INFINITELY LONG HOMOGENEOUS CYLINDER By G. A. Gamburzeff Gerlands Beiträge zur Geophysik, Band 19, Heft 2/3 Leipzig, 1928, pp. 210-230. The present work is a. contribution to the quastion of the reason for the magnetic and gravitational anomalies in the government of Kursk (Russia).

Jan 1, 1929

By R. H. Nicholas

Shuttle cars have undeniably proved their worth as a means of transporting coal underground; however, several factors have arisen in connection with their possible improvement. This report .discusses the effect of shuttle cars that employ rough-tread and smooth-tread tires on mine roadbed, the amount of dust thrown into suspension by the use of such tire treads, and the service rendered by each type of tire. Involved, also, in this study are observations on the use of different amounts of calcium chloride on the haulageways.

Jan 1, 1949

By D. R. Tweeton

The U.S. Bureau of Mines has developed tomographic computer programs for geophysical applications and is distributing them as part of a Bureau plan to facilitate the transfer of technology to potential users. These programs were developed for predicting and monitoring the flow pattern of leach solution during in situ mining. The Bureau has also applied them to assessing high-wall blast damage and examining the integrity of mine-related geological structures. This report describes the curved ray program BOMCMTR (Bureau of Mines curved ray tomographic reconstruction), tells how to run it, and gives examples with synthetic and field data. BOMCRATR provides optional mathematical constraints to counteract the nonuniqueness of tomographic reconstructions with crosshole data. These constraints include limiting the maximum and minimum velocities, fixing the velocity at any point to any value, and establishing layers in which velocity does not vary with horizontal position. The user can test for nonuniqueness by varying the initial velocity pattern, The program can perform either curved or straight ray analysis. Ray paths are calculated analytically in triangular pixels, which is faster than incremental numerical approximations,

Jan 1, 2010

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By W. E. Robinson

Oil-shale kerogen was processed into oil and oil products before the first oil well was completed by Drake in 1859. However, because of economic and other advantages, natural petroleum has been the principal source of liquid fuels and lubricants since 1859 and is a convenient root of many [organic] chemicals in common use today. In recent years the difference has narrowed between the cost of producing liquid fuels from well petroleum and other sources. This narrowing of cost difference has resulted both from the increased cost of finding new sources of petroleum in the United States and the experimental demonstration of lowered costs for synthetic liquid fuels by the Federal Bureau of Mines and by industry. Available petroleum resources of this country are being reduced and eventually may be inadequate to meet the demand. Alternate means of assuring an adequate supply of liquid fuels for this country include the development of processes for utilizing other carbonaceous materials such as oil shale and coal.

Jan 1, 1960

By John L. Morning

Although faced with a slowdown in the world economy, continued inflation, and rising costs, the mining industry exceeded its 1974 raw mineral production value of $55.1 billion by 13%. The increase was due to value increases in the production of fuels and nonmetals; metals reported a decrease in value. Of 23 metals produced, 14 showed value increases; of 44 non-metals produced, 26 reported value in-creases. Because of increasing costs and depletion of high-grade reserves, the mining industry continued to rely on new technologies to maintain its profit margins. In the surface mining sector, the development of new tools and equipment played a large part in increasing production and maintaining this goal. Some of the types of equipment developed were instrumentation for control of pit slope stability, shovel power transmissions, electric wheel trucks, and single-flight conveyor systems.

Jan 1, 1977

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973