Search Documents

This Bureau of Mines investigation addressed two primary issues of air velocity measurement in mines: the determination and use of correction factors, and the development of guidelines for the selection of a suitable site at which the measurements should be taken. Other facets of the investigation included a comparison of measurement methods and devices, and aircourse cross-sectional area measurement. The study consisted of theoretical, laboratory, and in-mine investigations. The measurement devices included in the experimental phase were vane anemometer, vortex shedding anemometer, a prototype thermoan-emometer, smoke tube, and oil of wintergreen sprayer. The measurement methods included single-point centerline, timed-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices. The study resulted in guidelines for measurement site selection that are applicable to most inmine situations. It also showed that the use of correction factors is problematic. There are many potential pit-falls and there are cogent arguments against using certain correction factors. However, generalized correction factors were developed that can be successfully applied in routine ventilation work, provided that their use is properly understood.

Jan 1, 1985

By R. E. Morgan

Two sizes of Pennsylvania anthracite were gasified in the new-type Lurgi pressure generator at the Dorsten, Germany, works of the Steinkohlengas, A. G. These tests demonstrated that Chestnut-size anthracite and a Rice-Buckwheat mixture containing 27 and 19 percent ash, respectively, could be gasified satisfactorily at an elevated pressure in a fixed bed with oxygen and steam. These coals were especially prepared to approximate a rough-cleaned coal and a washed and screened product. The operating data obtained from the two tests and materials requirements are summarized. A wide range of reactant ratios could not be tested, nor could optimum operating conditions be determined, as the generator was being used throughout the testing program, employing normal operating practices, to produce gas for the gas grid; and the most economical coal, steam, and oxygen ratios may not have been used. Comparative costs are presented of the raw materials required for producing a high-B.t.u. gas, based on the operational data obtained from these tests and, to some extent, on data extrapolated from laboratory experimentation. A flowsheet of a proposed process for producing a high-B.t.u. gas by Lurgi gasification, followed by methanation, is also included.

Jan 1, 1958

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By S. C. Termes

To help develop the basis for new fine-particle separation methods, the Bureau of Mines has investigated the use of cross-linked starches containing four chelating groups--carboxylate, iminodiacetate, dietha-nolamine, and xanthate--as flocculants for selected metal oxide and hydroxide mineral fines. It was found that those starches capable of interacting with the mineral surface by a chemisorpti,on mechanism (as indicated by zeta potential measurements) produced the highest recover-ies and'grades of the metal oxide or hydroxide when flocculated from a binary mixture with quartz. The effects of pH, dispersing agent, stirring rate, stirring time, and starch dosage on selective flocculation were studied for binary mixtures of hematite and chromite with quartz. Floc strength becomes important in achieving maximum recoveries by mechanical postflocculation separations.

Jan 1, 1985

By W. P. Diamond

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development program. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By C. P. Mishra

The Bureau of Mines investigated the availability of mercury from 22 deposits in market economy countries. The 15 significant deposits evaluated have demonstrated resources of approximately 25 million metric tons of ore containing 5.3 million flasks of mercury and account for more than 85 pct of the demonstrated resources for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau determined the mercury production potential of each deposit. At a January 1984 mercury market price of $300 per flask, the deposits evaluated could economically produce an estimated 2.5 million flasks of mercury from six mines operating at the time of this study; no mercury is available at this price from nonproducing operations. At $600 per flask, approximately 4.5 million flasks of mercury are available. For production costs up to $300 per flask, operating mines could supply mercury at the current production rate of 114,000 flasks per year until 1988, when the amount of mercury available from these deposits would decrease. This decline could be offset by the development of resources currently reported at the identified level (17 million flasks) at much higher production costs.

Jan 1, 1985

By Robert L. Frantz

This report is a part of the project "Study of the Human Factors Aspects of an Automated Continuous Mining Section". The report covers three phases: Phase I Assessment of the Impact of the Automation Technology on Mining Health and Safety. Phase II Estimation of the Cost-Effectiveness and Productivity of Automation. Phase III Prediction of the Psychological and Organizational Impacts of Automated Mining, The investigation determines that the automation of a continuous mining section will improve the health and safety of the miner, increase productivity and decrease mining costs, result in a more attractive and desirable working environment, and result in a greater rate of return on capital investment.

Jan 1, 1977

By F. D. Everett

The Federal Bureau of Mines reviewed the status of tungsten deposits of Utah in 1959. Industrial requirements of tungsten during emergencies have exceeded the domestic supply, and a knowledge of the sources of this strategic element may be helpful in the future. Tungsten occurs as the mineral scheelite in deposits that have been developed or explored on approximately 60 properties in 10 of the Great Basin ranges of Utah, none of which were being worked in 1957-59. Ores from most of the productive areas are similar in that they are contained in tactite deposits on or near the contact of calcareous and acidic intrusive rocks. The tactite ores consist predominantly of the silicate minerals garnet, epidote, and diopside and the carbonate rocks limestone or dolomite. Scheelite, where present, is disseminated irregularly in the tactite. Tungsten ores from Utah mainly have been produced from small deposits worked in World Wars I and II and the Korean campaign. The ores were either hand sorted to a grade ranging from 0.5 to 1.0 percent tungsten trioxide (W03) or were beneficiated in small mills to higher grade concentrates. The largest reserve appears to be in the area of the Notch Peak intrusive in the House Range, Millard County. A large part of the reserve in the House Range is mineralized tactite containing 0.2 to 0.3 percent W03. Research on flotation by the Bureau of Mines has indicated a method of concentrating scheelite in tactite ores that average 0.25 percent W03, with at least 85 percent recovery. The concentrate assays more than 5 percent W03 and can be processed into artificial scheelite ready for industrial use.

Jan 1, 1961

By W. F. Watts

The U.S. Bureau of Mines has conducted research on methods to reduce and to measure diesel particulate matter (DPM) aerosols in underground coal mines. One objective of this report is to present findings from an investigation of the DPM reductions obtained by an engine-mounted integrated control system consisting of a dry system (DS) and a diesel particulate filter (DPF). Another objective is to present results from the usc of a size selective personal sampler to measure DPM concentrations in an underground coal mine. Bureau laboratory tests of the integrated dry system and diesel particulate filter (DS-DPF) have shown that DPM emissions can be reduced up to 97 pet with little change in gaseous emission concentrations. The DS-DPF is undergoing certification tests conducted by the Mine Safety and Health Administration (MSHA). Subsequent to passing all safety requirements, it will be tested in an underground coal mine. A baseline survey of DPM concentrations and aerosol size distributions in a cooperating mine was completed in August 1988. A prototype DPM personal sampler was tested during this survey. Based on results from this test, an improved unit has been developed. This unit is scheduled for extensive field testing by MSHA in 1989.

Jan 1, 1989

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

By M. E. Volin

The tungsten potentialities of the Combination mine were examined by a mining engineer of the Bureau of Mines in 1947. A report based upon his personal knowledge of the mine and the results of the examination contained recommendations for further investigation. This report presents factual data from Bureau of Mines field investigations begun in August 1947 and continued until December 1948, except for a 5-month recess during the first winter. The Combinat.ion mining property of 52 patented claims and 15 patented mill sites is in the Black Pine mining district, Granite County, Mont., 11 miles northwest of Philipsburg. The altitude in the mine vicinity is approximately 6,500 feet.

Jan 1, 1952

By J. L. Buckley

A survey of previous underground mine fires revealed a number of reported fires may have been caused by malfunctioning stationary electrical equipment. Therefore, an evaluation of conventional fire protection systems was conducted to determine their usefulness in the protection of this equipment. To simplify the problem and facilitate the handling of data, the under-ground mine was divided into nine work areas. Representative combustibles and associated hazards characteristic of each area were identified. Conventionally available fire protection systems were then examined and evaluated to determine engineering and cost feasibility, effectiveness and reliability for the development of fire protection guidelines which could be used within the nine areas of interest.

Jan 1, 1976

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 78,000-acre Garns Mountain study area in southeastern Idaho. The area had been proposed for Wilderness. It is underlain by Paleozoic to Mesozoic-age sedimentary rocks about 11,000 feet thick. Rocks have been faulted, offset, and folded as part of the northerly-trending Idaho-Wyoming Overthrust Belt. Study area mineral occurrences are: phosphate in the Permian Phosphoria Formation; coal in the Cretaceous Frontier end Bear River Formations; and uranium in carbonaceous and phosphate-bearing shales and coal of these formations. Four zones of phosphate are estimated to contain about 528 mitt ion tons of rock with over 10% P205; samples of phosphate-rich rock also contained as much as 3950 ppm chromium, 3280 ppm vanadium, 23 ppm gallium, and 5540 ppm zinc. Fragments of poor-quality coal and carbonaceous shale were found in the area; coal was mined near the northeast border. Uranium content up to 0.016% U3O8 is in carbon-rich shales. Oil and gas were drilled for, with minimal success, in folded sedimentary rocks (frontier and Nugget Sandstone) in the Horseshoe anticline, near the east border. Examined workings included 12 dozer cuts, 4 trenches, 2 prospect pits, and 2 caved adits. No production is known, and no leases or claims are held for the area.

Jan 1, 1992

By Carl L. Bieniewski

U.S. molybdenum production increased fivefold from 18.2 million pounds in 1946 to 90.5 million pounds in 1966, and constituted 87.3 percent of the total free world supply in the 1946-66 period. Mining development in other free world countries in the next few years may reduce the magnitude of the U.S. position, although similar development planned for the United States may counteract some of the relative gains by those countries. In 1966 two-thirds of the reported molybdenum consumption in the United States by end uses was as an alloying element in steel. Molybdenum also has important use as an alloying element in iron and high-temperature alloys. Consumption of molybdenum metal for making fabricated parts has increased in the past few years, especially in the space and nuclear industries. Molybdenum compounds are used mainly for making pigment, catalysts, and lubricants. Based on producer reports of shipments of primary products to domestic customers, U.S. consumption of molybdenum increased from 16.5 million pounds of molybdenum in 1946 to 65.6 million pounds in 1966. U.S. molybdenum reserves are now estimated to be 5.9 billion pounds of recoverable molybdenum, an increase of 2.1 billion pounds above previous estimates. Molybdenum ores account for 71.4 percent of the reserves, copper ores for 22.3 percent and copper-molybdenum, tungsten, and uranium ores for 6.3 percent. Several methods for predicting future demand are illustrated and estimates of demand using these methods were made for 1975. Based on present capacities and announced company plans for future developments, estimates of annual production were made for 1967 through 1975 for the United States, Canada. Chile, Peru, and the free world. These data indicate that molybdenum production in 1975 for the free world is expected to be 246 million pounds with the United States producing 68.2 percent and Canada, Chile, and Peru 30.3 percent.

Jan 1, 1970

By D. Harrington

In recent years over 100,000 persons have been killed annually in the United. States by accidents; about one-fifth of these have been workers in some of our industries; about one-third have been killed by motor vehicles; about another third have mot death in home accidents, chiefly falls, burns, scalds, explosions, poisons, asphyxiations, suffocations, cuts, scratches, and so forth; and the rest have been killed in public accidents, excluding those caused by vehicles but including accidents on railroads or electric cars, drowning, and deaths by firearms and. other means. Definite statistics on nonfatal accidents are not readily available, but at least 10,000,000 fairly serious accidents probably occur in the United States annually. The latest industrial-accident statistics are obtainable from 1935 National Safety Council publications, in which annual industrial fatalities are divided about as follows (in round numbers): Agriculture, 4,500; trade and service, 4,500; construction, 3,100; transportation and public utilities, 2,900; manufacturing, 2,600; mining, quarrying, petroleum, etc., 1,900.

Jan 1, 1938

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By N. S. Dalal, X. Shi, P. M. Gannett

"Chromates are known to induce tumors (1, 2), mutations (3), and DNA damage (4-6). However, the underlying biochemical mechanism(s) is (are) not fully understood (6). Recent studies have indicated that hydroxyl (·OH) radical may play an important role (7-11). The mechanistic studies of Cr(Vl)-related ·OH radical generation in biochemical systems have shown the reaction of a Cr(V) species with hydrogen peroxide (H20 2 } through a Fenton-like mechanism to be one of the important steps (9-11): Cr(V) + H20 2 - Cr(VI) + ·OH + OH-. (1)In biological systems the Cr(V) species are generated via the reduction of Cr(VI) by a variety of components, such as microsomes (12), mitochondria (13), mitochondrial electron transfer complexes (14), and at least three flavoenzymes (glutathione reductase (GSSG-R),3 lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase) (9, 15, 16). In the case of flavoenzymes, Cr(V) formation is accompanied by the reduction of molecular oxygen ( 0 2 ) to H20 2 • The Cr(V) species then reduces H20 2 to generate •OH radicals and Cr(VI) (16).To understarid the mechanism by which Cr(V}-generated ·OH radicals cause cytotoxicity, Aiyar et al. (8) investigated the reaction of Cr(VI) and H20 2 to generate ·OH radical and its reaction with 2'-deoxyguanine (dG) to form 8-hydroxy-2'-deoxyguanine (8-0HdG}:"

Mar 1, 1992

By D. A. Reynolds, J. D. Davis

"This work was begun in l928, with the cooperation of the American, Gas Association, and the Association contributed financial aid for that year and for the 4 years following. In 1933 financial aid was discontinued, but the Advisory Committee, under the able, Chairmanship of J. S. Haug, has continued to function through the years to the present date. Mr. Haug's annual reports have been published in the Proceedings of the American Gas Association. The purpose of this paper is to bring the index of coals tested by the Bureau of Mines-American Gas Association (EM-AGA) method up to date, to discuss development of auxiliary tests, and to outiline the uses to which the methods have been put in promoting the war effort.COALS TESTEDThe test methods developed with the advice of the Advisory Committee had been applied to 66 coals up to 1942, and an index giving the serial number, origin, and analyses of these coals was published as Bureau of Mines Technical Paper 637. Since this paper was published, 20 additional coals have been tested; the source and analyses of these coals are given in table 1. The table also refers to publications that have been issued. Complete series of tests at high, medium, and low temperatures,have been made on most of these coals, and blending tests with 20 and 30 30 percent of low-volatile coals have also been made at 900°C.; however a few low- and medium-volatile coals (60, 70, 74, 79, and 80) were bested,at high temperatures only. Those coals were mined in eastern Oklahoma and western Arkansas. The test work included low- and high-temperature assay tests, petrorraphic analyses, and plasticity tests since its inception; and for the last 20 coals of the series, expansion and oxidation tests have been made where applicable."

Jun 1, 1944

By G. J. Slavens

The U.S. Bureau of Mines conducted research on preparing submicrometer titanium nitride (TiN) powder as a substitute for tungsten carbide (WC) in cutting tools and wear-resistant parts. Earlier research on a small scale was expanded to include a larger reactor. The TiN powder was produced by contacting titanium tetrachloride (TiCI4) with anhydrous ammonia (NH3) in the presence of Mg at 1,100° C. The powder was collected in an electrostatic precipitator (ESP) filled with ultra-high-purity (UHP) Ar. All collected powder was thermal vacuum distilled to remove Mg and magnesium chloride (MgCl2), leaving the purified TiN. Powder handling and purification procedures were conducted to assure low oxygen content in the powder product. Oxygen content in the distilled TiN powder product was as low as 0.40 wt pct. Nitrogen averaged near 22.0 wt pet with a high of 22.4 wt pct. The purified powder product had an average median particle diameter of 0.14 µm with a standard deviation of 0.09 µm.

Jan 1, 2010

By Thomas C. Atchison, Joseph M. Pugliese

Six explosives were compared by measuring their strain- producing abilities in limestone . Peak strain , e , varied with scaled distance , R/Ro , according to the following equation : € = Kc (R /R 。)- ". The distance exponent , n , was a constant of the rock and did not depend upon explosive . The strain intercept , Ke , increased with increasing detonation pressure of the explosive . The strain intercept also depended upon the explosive- to - rock impedance ratio . For impedance ratios from 0.53 to 1.38 , the strain intercept was approximately proportional to the medium stress , Pn , as calculated from the explosive detonation pressure , P , and the explosive - torock impedence ratio , Z , by the simple elastic theory relation : P = 2P / ( 1 + Z ) . PD However , the data indicated that , at lower values of impedance ratio , the strain intercept is relatively larger than would be expected from the simple elastic theory . The results presented provide a simple method for predicting the relative effectiveness of different explosives in breaking limestone from the detonation pressures and characteristic impedances of the explosives .

Jan 1, 1964