Search Documents

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By R. Duncan Gardner

This paper describing the milling practice at the concentrator of the Harmony Mines Co. is one of a series being; prepared by the Bureau of Mines on milling methods and costs in the United States. For the period February 15, 1929, to June 1, 1929, the concentrator treated 200 tons of copper ore per day containing 3.84 per cent copper and recovered 99.2 per cent of the total copper in concentrates averaging 26.61 per cent copper. Milling practice at the Harmony Mines is in most respects similar to the usual practice at the average flotation concentrator producing bulk flotation concentrates. The exceptionally high recovery is due to a number of minor conditions. These minor details will be stressed throughout this paper.

Jan 1, 1930

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By Clayton M. Rumsey

In 1984, the U.S. Bureau of Mines conducted a mineral survey of a 26,598-acre study area which includes the 23,702-acre Mt. Limbo Wilderness Study Area (NV-020-201). The study area is 65 miles northeast of Reno, NV, and is underlain mainly by Cretaceous granodiorite that comprises the Selenite Range. Tertiary basalt, rhyolite, and sedimentary rock as well as Quaternary alluvium and lake deposits are exposed near the study area boundary. Mines just north of the area in the Hooker mining district produced tungsten ore in the 1940's and 1950?s. Similar deposits are not known in the study area. Disseminated gold is in sinter about 6 miles west of the study area and at several other locations regionally.

Jan 1, 1986

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

In 2005, a total of 7,111 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA). ? Sand and gravel mines were the largest mining sector, comprising 48.5% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By Raymond G. Travis

This report describes coal-mining methods, power requirements, coal production and distribution, and coal resources of the Bull Mountain coal field in Musselshell and Yellowstone Counties, south-central Montana Investigations in the field, were conducted by Bureau of Mines engineers The report contains a short summary of the geology and geography of the field and discusses the following information secured during the field study: Method of mining practiced at each mine, including a description of each phase of the mining cycle. Coal produced and its distribution at each mine. Power requirements and the consumption of electricity per ton of coal produced by mines. Number of non employed by mines, and the production per man per shift underground and the over-all production per man employed. Estimates of future production and power requirements for the field as a whole. This information should be of benefit to any company or individual planning the development of now coal mines in the area or the expansion of present operations.

Jan 1, 1950

By M. M. Fine

The flotation work on samples from nine fluorspar properties in Crittenden and Livingston Counties, Ky., reported herewith was part of a wartime project that resulted in increasing the supply of metallurgical-grade fluorspar. The samples were tailings, dumps, and waste rock that had been rejected in previous milling operations. All were treated successfully by flotation to yield metallurgical-grade concentrates with recoveries ranging from 77.5 to 98.3 percent of the fluorite. After the laboratory testing, the results of which were available to the owners and operators of the properties, many of the tailing ponds and rock dumps were milled. The real value of this report, therefore, is to show the operators of gravity concentration plants the possibilities of re-treating waste products by flotation either at some future time or currently with the gravity

Jan 1, 1948

By D. L. Soreck

The hazards to the public posed by abandoned mine shafts are well documented. As private development encroaches on previously mined areas, the potential for fatalities and serious injuries from abandoned mine shafts increases. The U.S. Bureau of Mines has conducted research into cellular concrete as a material for sealing these openings. The current work involves testing the characteristics of cellular concrete before and after it had been pumped or dropped from different heights into a simulated mine shaft. Cellular concrete was pumped vertically up to and subsequently dropped from heights of 18 and 37 m into concrete forms. Wet density measurements were made at multiple sampling points in the test circuit. Air content determinations and uniaxial compressive strength testing were conducted. Research results showed significant loss in air content and changes in the characteristics of cellular concrete during pumping or dropping from various heights. Recommendations on effective use of cellular concrete for sealing abandoned mine shafts are made.

Jan 1, 2010

By Howard W. Kilau

The U.S. Bureau of Mines is investigating surfactants added to water sprays to enhance the control of dust during coal mining operations. The objective of the present work was to establish the general applicability of adding sulfate ion to anionic surfactant solutions in order to improve wetting action. This was pursued through laboratory wettability testing of four anionic surfactants and one nonionic surfactant in combination with various concentrations of sulfate ion. The experimental results demonstrated that the addition of sulfate ion enhanced the wetting characteristics of all the anionic surfactants when applied to hard-to-wet coals, while easy-to-wet coal showed more complex wetting behavior. Sulfate ion in the presence of nonionic surfactant enhanced wetting only slightly or not at all. Surface tension measurements of the dilute aqueous surfactant-sulfate anion solutions indicated this property was not important in coal-wetting phenomena, as long as the value was below the critical value for coal. Sulfate ion helps surfactant reduce surface tension but primarily appears to affect wetting action by altering the adsorption characteristics of surfactant on the coal surface.

Jan 1, 1990

By J. D. Davis

The Bureau of Mines Coal Carbonization Laboratory has been interested for the past 20 years in the quality of coke in connection with the selection of coals for the manufacture of coke. The principal experimental. method of carbonization, whereby 100- to 200-pound charges are carbonized in sheet-steel cylindrical retorts with recovery and determination of the properties of coke, gas, and products, was developed in cooperation with the American Gas Association,4 5 and it is known as the BM-AGA method. Results of the investigations of 90 coals included in the BM-AGA Survey of the Carbonizing Prop¬erties of American Coals have been published; 6 and, in addition to these, about 200 coals have been carbonized over limited temperature ranges. Because coke from cylindrical retorts differs in shape from that made in rectangular ovens, the BM-AGA method has been criticized, although those who developed it have always believed that it served well as a means of measuring the relative strengths of cokes from different coals. It is recognized that no laboratory-method carbonization, even on a large twit, can yield results that exactly duplicate those obtained in commercial ovens and retorts. However, with the completion and satisfactory performance of an experimental vertical slot oven of 500-pound capacity at the University of Illinois Geological Survey Laboratory,' the opportunity to directly compare BM-AGA coke with coke made by two-sided heating became available and the necessary test apparatus was installed. The Bureau of Mines slot oven, which is similar to that designed by the University of Illinois Geological Survey, has been used to carbonize 11 coals (or blends) tested by the BM-AGA method. This report compares the results obtained by the two methods.

Jan 1, 1950

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By M. C. Irani

This Bureau of Mines survey of methane emissions indicates that total daily emissions have declined from 227 MM ft3 in 1971 to 214.7 MM ft3 in 1973. The highest average daily emissions in million cubic feet per day observed in U.S. bituminous coal mines were, in decreasing order, Monongalia County, W. Va., 40.7; Marion County, W. Va., 23.1; Buchanan County, Va., 22.1; Washington County, Pa. , 12.4; Greene County, Pa. , 11.7; McDowell County, W. Va. , 11.4; Cambria County, Pa., 9.8; Jefferson County, Ala., 9.5; Wyoming County, W. Va., 6.0; Marshall County, W. Va., 4.8; and Indiana County, Pa., 4.8.

Jan 1, 1974

By Selim E. Woodworth

This paper, describing the milling practice on the Mother Lode as typified in the mill of the Argonaut Mining Co. at Jackson, Amador County, Calif., is one of a series prepared by the United States Bureau of Mines. The data herein presented and furnished through the courtesy of E. A. Stent, managing director and vice president of the Argonaut Co., covers operations from 1914 through the year 1929.

Jan 1, 1931

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

In 2006, 14,885 mining operations reported employment data to the Mine Safety and Health Administration (MSHA).1 Almost half (48.2%) were sand and gravel mines, followed by stone mines (30.7%), coal mines (14.2%), nonmetal mines (5.0%), and metal mines (1.9%).

Jan 1, 2008

By J. W. Paul

Mine foremen are employed in coal mines for two reasons: First, so that the underground work. may proceed in an orderly manner and that each employee gives attention to his duties; and second, by reason of the State law which re- quires the employment of such officials to see that the laws relating to safety are carried out. It may be seen that, with these two duties, the foreman has wide scope of authority and much responsibility. As foreman of operations he has to meet certain economic questions that contribute to the cost of producing the coal, and as the agent of the State he must also supervise and coordinate the work in such manner as to insure that the employees work under safe conditions. As the roof of coal mines is the source of the greatest hazard naturally the care of the roof must take much thought and planning on the part of the fore- man; and this circular is therefore presented to call attention to some things he may do to prevent injury to the workmen by falls of the roof material or coal. Mine foremen, in the principal coal-producing States, are certified by a State board which prescribes certain qualifications, experience, and character, attested by examination and personal endorsement. Certified foremen, therefore, are men who have had experience underground and know roof conditions and timber- ing methods. The suggestions herein are based upon observations made at many mines and collectively embrace practices that have been found to be in effect and pro- moted by experienced mine foremen:

Sep 1, 1930

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923