Search Documents

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned & name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled except the deep holes drilled to test geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Anthony Edey

This report describes work performed and results obtained for the technical and economic feasibility study of oil production by mining methods. The characteristics of oil fields which would make them amenable to mining techniques were identified. An inventory of known U.S. oil fields that offer this potential was collated. This was further divided into fields having potential for underground and surface mining systems development. Several candidate fields that fit particular underground and surface mining system types were then selected. Conceptual mining systems were designed for the selected fields. Five underground and four surface methods were chosen. Costs of oil production were estimated for these selections. The impact of oil mining an the environment was also considered.

Jan 1, 1978

By Oliver Bowles

"The town of Monson in Piscutaquis County, Maine is the, center of an important site industry. Monson slate has a nation-wide reputation, particularly for electrical switch boards, and the deposits have been worked for the manufacture of such products for many years. Open-pit quarrying is the method most commonly employed in obtaining slate. Underground methods have been used in the Peaon Bottom district near Delta, Pennsylvania, but the quarries that were thus operated are now abandoned. Underground methods have been used more extensively in foreign countries, the most famous example being the slate mines at Angers in France, where an over-head stoping method has been employed successfully for many it is only under special conditions that underground methods can be successfully used. If the deposit is wide and relatively thin, or if the material is too unsound to constitute a safe roof, open-pit methods must be used, for slate is too low-priced a commodity to justify the heavy expense of any timbering methods. It is only where the deposit is relatively narrow, of great depth, and sufficiently sound to afford a strong roof that ordinary mining may be employed.The best slate beds in two of the three quarries operated at Monson are no worked by underground methods. The chief bed worked by the Portland Monson Slate Co. is 10 feet thick, stands vertical and strikes N. 63º F. The slaty cleavage is vertical and crosses the strike of the beds at an angle of 5 to 10°. The grain or second direction of splitting is vertical and perpendicular to the cleavage. In addition to the 10-foot bed, to 2-foot beds and one 5-foot bed are available but are not now utilized. In the Monson Maine Slate Co. quarry (the old Pond quarry),a greater number of beds available, but at present quarrying is confined to a single bed about 9 feet thick which dips 30º S.E. and strikes N. 47ºF. The slaty cleavage is vertical and strides N. 45º F., while the grain strikes N. 45-50º W. and is also vertical."

Nov 1, 1920

By M. M. Fine

A process for simultaneously reducing and indurating iron are pellets was developed by Bureau of Mines laboratory research and confirmed on a continuous pilot plant basis. Moist iron are concentrate was balled, mixed with solid reductant, and heated at about 1,100° to 1,150° C. On a small scale, a variety of concentrates and fuels were utilized successfully. The pilot rotary kiln tests were limited to natural magnetite, synthetic magnetite, lignite, and anthracite. In both cases, partially reduced pellets with excellent physical properties were regularly produced with average analyses of at least 80 percent total iron and 60 percent or more metallic iron. These and other prereduced pellets were smelted in the Bureau's experimental blast furnace facility, Bruceton, Pa. With prereduced spheres comprising 85 percent of the burden, the coke rate was approximately half that with standard oxide pellets and production of hot metal was increased by 75 percent. Economic appraisal of the cost of making hot metal indicates that reduced pellets could be more profitable than any other iron raw material in both investment capital and daily cost of operation.

Jan 1, 1970

By D. R. Wilburn

The Bureau of Mines investigated the potential availability of magnesium from 45 properties in market economy countries (MEC's). The 38 significant deposits evaluated have demonstrated resources of approximately 29 billion short tons (st) magnesium-bearing material containing 416 million short tons (MMst) magnesium oxide (MgO). Using data it gathered, the Bureau determined the magnesium production potential for each property including a 15-pct rate of return on invested capital. Total and annual availability assessments for the next 30 yr were completed for magnesium (Mg) metal, deadburned MgO, and caustic calcined MgO. At a January 1984 market price of $1.34/Ib Mg metal, the properties evaluated could economically produce an estimated 13 MMst Mg metal. At a market price of $400/st nonmetal magnesium product, these properties could economically produce 109 MMst deadburned MgO and 43 MMst caustic MgO. These properties could produce approximately 301,000 st Mg metal, 3.0 MMst deadburned MgO, and 430,000 st caustic MgO annually at current full production levels and 1984 market prices until at least the year 2000. Total 1984 MEC production assessed in this study was 153,000 st Mg metal and 4.3 MMst nonmetallic MgO products.

Jan 1, 1986

By Warren E. Morrison

This study was prepared in response to the need for a series of data that reflect the basic flow pattern of energy resources in the United States. To effectively measure and analyze energy,2 it is necessary to prepare balances that reflect both production and consumption, and the various forms energy resources take at different stages of utilization. Before energy can be measured it must also be put into a common unit. In this study the common unit used is the British Thermal Unit (Btu). The ideal point to survey energy is at the stage of final ultimate use, representing the useful work derived from the interaction of energy inputs and the prime mover. Unfortunately this concept of efficient or useful work from energy output cannot readily be measured in the aggregate. With the present available official data, energy measurement can be carried to the point of calculation of net inputs of energy3 into the economy at various stages of utilization. However, preparation of energy balances, on a net basis is hampered by the fact that this can only be done for years when the censuses of Mineral Industries and Manufactures are taken, usually at 5-year interval.

Jan 1, 1964

By Warren E. Morrison

This study was prepared in response to the need for a series of data that reflect the basic flow pattern of energy resources in the United States. To effectively measure and analyze energy,2 it is necessary to prepare balances that reflect both production and consumption, and the various forms energy resources take at different stages of utilization. Before energy can be measured it must also be put into a common unit. In this study the common unit us d is the British Thermal Unit (Btu). The ideal point to survey energy is at the stage of final ultimate use, representing the useful work derived from the interaction of energy inputs and the prime mover. Unfortunately this concept of efficient or useful work from energy output cannot readily be measured in the aggregate. With the present available official data, energy measurement can be carried to the point of calculation of net inputs of energy3 into the economy at various stages of utilization. However, preparation of energy balances, on a net basis is hampered by the fact that this can only be done for years when the censuses of Mineral Industries and Manufactures are taken, usually at 5-year intervals.

Jan 1, 1964

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace- time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200- foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By Merwin H. Howes

Gnome shaft, situated about 24 miles southeast of Carlsbad, N. Mex., was designed and sunk by the U.S. Atomic Energy Commission for conducting a peace-time experimental nuclear explosion in the thick salt beds of the Permian Salado formation. Excavation was started July 1, 1960, and completed July 26, 1961. The 10-foot diameter shaft, lined with concrete through the rock section, was sunk 1,216 feet. A drift was driven approximately 1,140 feet on the 1,200-foot level terminating in a shot chamber. On completion of 100 feet of shaft, by means of a truck-mounted crane, facilities were installed for conventional sinking. About 709 feet of rock and 506 feet of salt were encountered in the shaft. Salt beds at this place are reported to be over 1,200 feet thick. The overlying rock section varies greatly in composition and thickness of beds and contains a 28-foot bed of water-bearing dolomite. The aquifer was sealed to facilitate shaft sinking and to prevent water-seepage damage in the salt section of the shaft. Sealing was accomplished by grout injection through holes drilled into the aquifer and by grouting behind the concrete liner.

Jan 1, 1963

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles 'wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

This publication summarizes, for potential contractors and all other interested parties, the research and development of in-house and contract projects programmed by the Bureau of Mines for fiscal year 1983 (October 1, 1982-September 30, 1983) under its Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1982

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). ? Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Jan 1, 2008

Coal mining in Indiana is limited to the south-western portion of the state, with coal currently being recovered in 19 counties. The coal-producing area of the state covers approximately 6,500 square miles. Although most of the coal in Indiana is recovered by surface mining methods, a small percentage is recovered through underground mining. To date, 40 percent of the known coal reserves have been removed. Indiana has about 33 billion tons of identified coal reserves, of which approximately 17 billion tons are recoverable using current technology. Of this recoverable coal, about 15 billion tons are recoverable by underground mining and 2 billion tons are recoverable by surface mining methods. The State of Indiana has regulated the environmental impacts of coal mining since 1941. Indiana was the second state in the nation to pass legislation requiring mined land reclamation. Its SMCRA regulatory program was approved July 29,1982, and its Abandoned Mine Land Program was approved July 29, 1982.

Jan 1, 1992

By Clinton C. Knox

The Townsite mine, consisting of 40 acres in the town of Cardin, Okla., is in the center of a highly productive part of the Picher-Cardin district of the Tri-State zinc and lead field. Previous to the time of the work done by the Bureau of Mines, the property had been partly explored by churn drilling, and an area-of about 8 acres in the southwestern corner had been exploited by underground workings. The Bureau of Mines investigation had as its object the more intensive development of the northern part of the property where previous drilling had indicated a possible ore deposit of commercial grade. Churn drilling by the Bureau began in September 1942 and continued to February 1943. Twenty holes totaling 4,827 feet of bore were completed. Utilizing the information gained from these drill holes, the Weidman Mining Co., lessee of the tract, sank a shaft and proceeded to the exploitation of the indicated ore bodies.

Jan 1, 1949

By Lon A. Williams

This report, authorized under Contract Number H0220065, Amendment Number Six, documents the results of an investigation of lighting system modifications and designs for working place illumination in high and low coal entries of underground coal mines. The portable and machine mounted system designs, both modified and prototype, represent a continuation of work performed under Contract Number H0111403, Amendment Number One. See the Final Technical Report dated May 26, 1972 for detailed information concerning this prior Contract. All modified and prototype systems met the performance requirements of Bureau of Mines Specification 2G, as proved by test. In addition, the systems met the requirement for illumination, as specified in the Contract and in the proposed standards which were generated in response to Public Law 91-173.

Jan 1, 1976