Search Documents

By Albert L. Toenges, Theodore R. Jolley

"INTRODUCTION The construction of frame houses (fig. 1) in recent years instead of the conventional sod hut (igloo) (fig. 2) by the Eskimos in the villages along the Arctic Ocean has increased the demand for fuel in these villages. The frame houses, which are not insulated against extreme cold and are difficult to heat, are equipped with Goal stoves. The well-insulated sod huts were heated comfortably with whale-oil stoves. In some years whaling is Door, consequently there is a demand for solid fuel.The Eskimo villages usually are on the sand spits at the mouths of rivers and points of land near the best fishing and hunting grounds. These narrow necks of land usually are sand bars that are not underlain with coal, and coal must be transported to the villages. Lack of development of coal deposits in the Arctic has made it necessary to import coal from the States, generally from 'Washington, to supply these villages. This coal is imported by boat and is received once a year. Its cost is, high, and development of coal deposits in the Arctic to supply these native villages should result in a considerable saving to the Government-operated schools and hospitals as well as to the natives.Early traders attempted to establish coaling stations in the Arctic, and the Eskimos generally know where the coal deposits are situated. A. reconnaissance of a number of deposits in the Arctic was made in the summer of 1946 by engineers of the Coal Division, Fuels and Explosives Branch, Bureau of Mines, and this report describes the areas investigated and suggests plans for the development of some of these deposits."

Dec 1, 1947

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.5

Jan 1, 1963

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By W. H. Tomlinson

This publication presents the basic text for a 20-hour accident-prevention training course developed for supervisors by the Federal Bureau of Mines. During the past 2 years, the course has been used by the Bureau in teaching more than 300 groups of coal-mine supervisors-men whose responsibility is twofold: To manage in production and maintenance phases of coal mining and to guide their men along paths of safety. This is a handbook for teaching teachers. In this handbook will be found references to safety practices followed by companies that consistently have low accident records. These companies credit their outstanding performance to the adoption and faithful observance of accident prevention by supervisors and workers alike on a wholesome, cooperative basis. Teaching safety to workers involves both on-the-job and classroom-type instruction. If such training is to be permanently effective, it must be reinforced consistently on the job by the immediate supervisor of the worker. This publication is intended to provide such a supervisor with the motivation to provide such follow-up and shows how he can accomplish it effectively.

Jan 1, 1962

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By Willard L. Hunter

The research described in this Bureau of Minus report was conducted to improve the chromium-iron ratio of offgrade chromite. Two methods were used: (1) Iron was selectively reduced from chromite by carbothermic reduction in an electric-arc furnace, and (2) a mixture of carbon, chromite, and sometimes fluorspar was chlorinated to remove a substantial part of the iron. Chromite concentrate from the Mouat deposit in Montana and from northern California was used in the test work. Chromium-bearing slag and chromite that had been beneficiated by a roast-leach process were each smelted to produce high-carbon ferrochromium. Iron was selectively reduced in a laboratory-scale., electric-arc furnace. Carbon additions to the smelting charges varied from 40 to 100 percent of the stoichiometric requirement, and slag basicities were varied from 0.4 to 1.0 chromium-iron ratios of more than 4:1 were obtained with 89 percent recovery of chromium in a chromium-bearing slag.

Jan 1, 1962

By M. P. Hardy

Copper-Nickel ores in northeastern Minnesota could establish a new industry in a region where underground mining has not been active. This study reviews geotechnical data relevant to the selection and design of underground mines in this region and by numerical structural analysis evaluates the importance of some geotechnical parameters to mine method selection. Because of the rapid development of computer modeling many new techniques have become available for modeling rock mass behavior in recent years. An overview of these methods is presented and their applicability to mine design reviewed. Methods included in this summary were the differential continuum models, such as finite Pint and finite difference, integral continuum models, such as boundary element, displacement discontinuity and boundary integral equation methods, and discontinuum methods such as the distinct block model. The displacement discontinuity method was used to evaluate the influence of geotechnical parameters on some aspects of mine design. Three problems; room stability, pillar stability on a weak inclined contact and sill pillar thickness influence on sill pillar stability, were analyzed to evaluate the relative importance of insitu stress field and joint properties on design. It was concluded that for stability analysis the initial horizontal stress is of most importance in all aspects of design. The position, orientation, persistence and strength of joints is also of primary concern. In a more general sense, however, it was concluded that detailed geotechnical parameters have much less influence on mine method selection than more general factors such as rock quality, initial stress state, orebody shape and economics.

Jan 1, 1978

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By Russell R. McLellan

Under the Heavy Metals Program, investigations were conducted at the old Badger dill placer mini in Nevada County California to collect data and information regarding drilling and sampling methods and deposit characteristics. The studies contributed to a team effort by five Bureau of Mines research groups to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California. This report describes the techniques used and the results obtained in the sampling and drilling stage of deposit delineation studies that were conducted by the Denver Mine Systems Engineering Group. Sampling included the collection and processing of 400 tons of largo and small volume samples from drill holes, underground workings, surface pits, and blast hole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicate that the bulk of the gold is within 40 foot of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of three types of truck-mounted drills including rotary, bucket and vibratory, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel.

Jan 1, 2012

By Agnes Y. Lee

As part of the U.S. Bureau of Mines program to improve base metal leach systems, pressure leaching of galena (PbS) concentrates in fluosilicic acid (H2SiF6) solution was investigated. Lead extraction was 93 pct when PbS was pressure leached in H2SiF6 at 95° C with 2OO-psig O2 pressure for 40 min, using ferric nitrate [Fe(N03)3] as a catalyst. The effects of several catalysts, O2 pressure, time, and acid concentration on leaching were determined. The purified leach solution was electrowon to recover high-purity Pb metal. The H2SiF6 used in leaching and electrowinning can be recycled continuously. A flow diagram was proposed based on this investigation. Elemental sulfur (SO) was recovered from the leach residue by solvent extraction. A method was also developed for treating the flnal residue to segregate the important byproduct elements such as Ag, Cu, and Zn and enable their recovery by standard commercial processes.

Jan 1, 1990

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962

In July 1982 the Committee on Underground Coal Mine Safety completed its study of safety in U.S. underground coal mines; the results of the study were published in the National Research Council report entitled Toward Safer Underground Coal Mines. One of the findings of this study was: THERE IS A STRONG CORRELATION BETWEEN MINE SIZE AND FATAL INJURIES. THE FATALITY RATE IN MINES WITH 50 OR FEWER EMPLOYEES IS NEARLY THREE TIMES THAT OF LARGE MINES (WITH OVER 250 EMPLOYEES), AND ABOUT TWICE THAT OF INTERMEDIATE-SIZED MINES (WITH 51-250 EMPLOYEES). Although the Committee explored possible reasons for the higher fatality rate in the smaller mines, it was not able to explain this phenomenon fully. Therefore the Bureau of mines requested that the Committee undertake a supplementary study of fatalities in small underground coal mines. The Committee met in the fall of 1982, discussed the problem, developed an approach to it, approved a program of statistical analyses, and authorized a panel of four committee members to explore the problem in greater depth. The panel, in turn, reviewed the results of the statistical analyses and met with the president of the National Independent Coal Operators Association and with several owners of small underground coal mines for a detailed discussion of the unique problems of small mines. Panel members examined 66 individual fatality reports prepared by Mine Safety and Health Administration (MSHA) inspectors who investigated fatal accidents that occurred in small underground coal mines in 1979 and 1980. This report is the result of those studies, analyses, and deliberations. The first draft was prepared by the panel, but the report has been reviewed and approved by the entire Committee.

Jan 1, 2011

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Robert D. Perry

This report describes methods of reclaiming abandoned or inactive tailings ponds and dams. The investigated sites were selected tailings deposits adjacent to metal mines in the southwestern United States and the Pacific Northwest. The basic data developed for each site consisted of the following: a review of existing literature: a site visit that included sampling of the tailings and surrounding materials; laboratory and engineering studies; and development of reclamation plans. Laboratory tests determined the gold and silver content of each tailings deposit and the chemistry of the tailings and surrounding materials. Reclamation plans that include approximate costs were developed for five tailings deposit sites. These ranged in size from 52,000 to 103,000,000 tons. Our conclusions on the remining potential of each site are based on the tailings assay and other technical data. This study concludes that remining as a reclamation tool is feasible at certain sites. Included in this report is a remining program as part of the overall reclamation plan for two sites. Our preliminary results indicate that remining as a reclamation tool is feasible for only one of them.

Jan 1, 1981

By Bradley V. Johnson

This publication summarizes the in-house and contract research and development projects conducted since 1974 by the Bureau of Mines for the control of noise and vibrations from surface mine blasting.

Jan 1, 1982