Search Documents

By John R. Holliday, William Marcum

Apogee Coal Company, DBA Arch of West Virginia, faced the challenge of drilling and blasting over one million cubic yards of high temperature overburden at its Ruffner surface operation near Logan, West Virginia. The overburden was removed above the Upper Five Block seam that was previously deep mined, abandoned, and later engulfed by fire. Borehole temperatures were measured above 700” F.

Jan 1, 1996

By Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Ahmet Varol, Ertugrul Kaya, Turgay Ozat

This paper presents analysis of environmental effects induced by cautious blasting during the construction of the Istanbul Subway 4 Levent - Ayazaga Darulsafaka Metro Tunnel Project carried out by the contractor, located at Northern Istanbul in Turkey. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S6-7-8 shafts of this tunnel route, ground vibration components were measured carefully by using five vibration monitors during the construction of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighboring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 107 records belong to 51 shots were analyzed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for these tunnel excavations and suggested for the test sites in order to estimate particle velocity of the ground vibrations. As a result of the studies, some practical charts are created in order to minimize the psychological effects of the shots, and simplify the authorities of shots’ job. And last but not least, make sure that the shots will be done in a controlled way.

Jan 1, 2011

By Steve Dillingham

PHYSICAL BLAST DATA Pattern Description All measurements related to the description of the physical blast pattern must be made with the mind-set that it has to tell a powerful factual story enabling a future accurate reconstruction of the event. A case has never been lost because too much factual information was available to assist investigators. An accurate physical description of the pattern must be provided based on the blaster’s observations of the pattern actually loaded. The blaster must measure the pattern size, depth, face heights, etc., recording only accurate results. All too often, a blaster records simple pattern sizes and information relayed to him or her from the driller, or from a phone call into the office the night before for powder pre-load inventory purposes. If a pattern was actually measured on the job site by the blaster to be 8.5 x 9.5’, it may, in fact, originally have been ordered at 9’x9’, 8’x9’, or 9’x l0’. In a claim situation, particularly flyrock, recording a “generalization” of what was loaded could result in an interpretation of a blaster’s negligence due to “not knowing or caring” what the actual pattern was, and not loading appropriately for conditions. It is important to remember that other documentation exists such as a drill log from a contract driller or mine records that may provide a different interpretation of the loaded pattern.

Jan 1, 2002

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Mattos J. L. C

Drilling and blasting with explosives in mining operations near communities require careful planning to mitigate socio-environmental impacts. Ground vibration, noise emission, flyrock, and dust dispersion are factors that may trigger conflicts with local populations. However, large-scale operations demand high productivity and intense material handling, making it essential to balance operational performance with impact control. The adoption of best practices, combined with advanced monitoring and mitigation technologies, enables sustainable mining even in proximity to inhabited areas. This study proposes the use of double and triple-deck blasting techniques with large-diameter boreholes (12 ¼” – 311 mm), addressing the sizing of charges and decks, as well as measures aimed at reducing noise perceived by nearby communities. The approach seeks to maintain the use of large drilling rigs already present in the operation, avoiding costs related to premature equipment replacement or expensive alternatives, while minimizing environmental and social impacts and promoting a more balanced and responsible mining model.

Jan 26, 2026

By Angel Rafael Fernandez, Yahya Khader Al-Harbi, Benjamin Cebrian Romo, Antonio Morato Medina

The kingdom of Saudi Arabia has set the goal to diversify their economy from oil into different fields including mining. As the vast Arabian Peninsula is explored, orebodies of Aluminium, Copper, Gold and Phosphates are found in high grades and tonnages. Hard rock is present in most of the projects and require high quality blasting in regard to ore dilution, wall control and fragmentation. Maaden Gold has currently 4 open pit mining operations 1 new opening and 2 underground. More projects are coming online in the next few months and years. A new generation of mining engineers need to apply drilling and blasting techniques that compete with modern and efficient open pit and underground mines.

Feb 6, 2023

By Thomas E. Ricketts

Occidental Oil Shale, Inc. constructed two commercial-sized modified in situ (MIS) retorts, Retorts 7 and 8, at its Logan Wash Oil Shale Mine in February and April 1981, respectively. One of the primary objectives of this two-retort program was to examine large-scale blasting reproducibility for commercial-sized retorts. The blast design used 545 blastholes and 550,000 pounds of explosive in ANFO equivalent per retort. Each retort was blasted using millisecond delay blasting caps tied into a single round. The blasts resulted in rubble beds very close to one another and to predicted results obtained using newly developed limited void blasting technology. The heights of the remaining void rooms over the beds after blasting were within 0.3 feet of one another. This excellent reproducibility is brought into true perspective when compared to the scale of the rubble beds which were 230 feet high with volumes of over six million cubic feet each.

Jan 1, 1984

By Denise de La Corte Bacci

The Brazilian Regulation NBR 9653 is a guide intended to evaluate mine and quarry blasting effects in urban areas. The first version, written in 1986 by the Committee of the Brazilian Associate of Technical Norms, is currently being revised. Current regulations specify a maximum PPV limit of 15 mm/s (0.59 in/s) without consideration of frequency or type of structures being protected. The present regulation is still a draft and it is not validated. Several different agencies and institutions have participated in the Committee such as the Environmental Agency from the State of São Paulo (CETESB), University of São Paulo (POLI-USP), University of Rio Grande do Sul (UFRGS), National Department of Mineral Resources (DNPM), Aggregate Industry (ANEPAC and SINDIPEDRAS), besides a number of industry representatives, explosives manufactures and independent consultants. The present regulation proposes to modify the limits of particle velocity and introduces new definitions and criteria for evaluation of vibrations, as well recommendations to address blast vibration complaints.

Jan 1, 2005

By Sami Kara, Yunseok Park, Seung-Joong Lee, Namsun Hwang, Michael Laing

This study conducts a comparative analysis of construction efficiency. In the first part we compared electronic and non-electric initiation systems, focusing on tunnel contour holes. Field blasting operations were executed across a variety of delays to identify the optimal delay time. This delay for the in-situ rock mass was determined through regression analysis of blasting vibration in contour holes and for overbreak/underbreak. The blasting results with the electronic initiation system using the obtained optimal delay, applied to contour holes, were compared with the results of the non-electric initiation system. The overbreak and underbreak decreased by an average of 2.7 cm and 5.8 cm respectively, by using the electronic initiation system. Moreover, the vibration reduction rate in contour holes region was reduced by 11.9% based on the blasting vibration estimation equation proposed by the Ministry of Land, Infrastructure, and Transport (MOLIT). Underground construction projects have become increasing popular as cities grow in both size and density. This growth severely limits the amount of useable space for new project on the surface, resulting in the decision to build them underground. This new policy however brings into focus the challenge of managing and reducing blasting related vibration due to the proximity of these projects to sensitive structures, utilities and foundations often present in urban environments. For this purpose, we have been required to manage the vibration by reducing the quantity of explosives used per round. Inspired by surface blasting techniques, we applied a decking mode to address and work around this challenge. We present in this paper the first attempt to blast a tunnel face using a decking method and reduce the charging per hole from 6 kg to 3 kg per hole and keep the same advance rate for this tunnel. The results are presented in the third part of this paper. In the second part we present the results of the decking mode in shaft. The use of the electronic initiation system in tunnel construction provides the users an effective tool to improve the overbreak/underbreak and keep the vibration at a low level with a large gain on the overall project schedule and budget. This what we want to demonstrate in this paper.

Jan 21, 2025

By Jihan Farhan Lubis, Putu Chandra Darmansyah

Ground vibration caused by blasting has become a common concern, especially when blasting is conducted near buildings or structures. Uncontrolled vibrations can potentially damage nearby infrastructure if appropriate control measures are not implemented. PT Tambang Semen SUKABUMI, a limestone mining company, is planning to carry out blasting activities near a crusher building located approximately 80 meters away. This building is classified as a Class 5 structure, with a maximum allowable Peak Particle Velocity (PPV) of 40 mm/s, in accordance with the Indonesian national standard SNI 7571:2023. To ensure compliance with this limit, a Signature Holes Analysis (SHA) was conducted using the Hanwha HEBS II electronic detonator initiation system. This analysis measured ground vibration from single-hole blasts, with the average vibration from three SHA holes recorded at 49 mm/s. A site constant analysis using the scaled distance formula yielded a multiple R value of 0.87. However, the ANOVA table showed a significance-F value of 0.24, which is greater than 0.05 indicating that the regression model used for prediction was not statistically significant. Using the SHA data and assuming a maximum of 30 blast holes, a recommended delay timing of 22 × 15 milliseconds was selected. This produced a predicted PPV of 17.25 mm/s. The comparison between predicted and actual PPV values demonstrates that the delay configuration derived from Signature Hole Analysis provides reliable results. The observed deviations range from -16% to +29%, with an average deviation of only 8%, indicating a high level of accuracy and consistency. Using the actual blast data, three model prediction were applied for predicting the most accurate prediction that close to the actual value. The SHA method, utilizing actual single-hole vibration measurements and optimized delay timing, provided the lowest average deviation of ±8% and the smallest absolute error (2.45 mm/s) from actual measurements, demonstrating high reliability for sites with sufficient signature data. Meanwhile, the log-log regression model yielded the highest coefficient of determination (R² = 0.751) and the smallest prediction deviation (3%) when standard deviation margins were considered, making it highly effective for predictive modeling.

Jan 26, 2026

By M S. Stern, R Aguila

To control direct blasting costs many open pit mines dewater and line wet blastholes before loading them with ANFO or Heavy ANFO blends of explosives. The plastic lay-flat tubing used for these liners can be punctured during loading and allow water to partly dissolve and desensitise the explosive column which reduces blasting performance.

Jan 1, 1997

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

By Stephen Mansfield

In open-pit mining operations, the drill and blast processes have a significant impact on the downstream operational performance of crushing and grinding of ores and recovery of metal. The blast pattern parameters, combined with the material properties, defines the run of mine fragmentation, which in turn drives the subsequent energy requirements for further processing and mill throughput. A common parameter used to describe a single hole or collection of holes is powder factor, the ratio of explosives to the quantity of material blasted. One often-neglected aspect of calculating powder factor is the explosives contained within the length of hole drilled into the top of the bench from the previous bench, known as subdrill. Explosives in the subdrill directly affect the bench below and thus do not contribute significantly to the results of the upper bench, even though they are traditionally included in the powder factor calculation. This paper presents geospatial data modelling methods that link individual holes from an upper bench to the bench below. This enables a new method for the calculation of powder factor, whereby the explosives in the subdrill from the bench above are included in the powder factor calculation of the bench below. This method allows for a clearer understanding of the impact of subdrill on fragmentation, and how variations in blast designs in the upper bench, i.e. hole diameter, burden, spacing, subdrill length, explosive type, primer position, etc., and accuracy of implementation, i.e. actual hole depths and explosive mass per hole, affect the powder factor and blasting results in lower benches.

Feb 6, 2023

By Jorge Cárdenas, Alejandro Luna

In mining simulation for fragmentation results prediction is of utmost importance to study feasibility, ensure safety, and estimate the correct use of resources in drilling an explosive to meet requirements and avoid excessive usage. One critical case is fragmentation prediction, developed through models. Developing a fragmentation model in a mining unit aims to control blasting results to align theoretical and real data and improve correlation. Therefore, it is essential to collect post-blast fragmentation data, organize it, and systematically process it to develop a suitable model that meets variable requirements. Using a robust system of equations, this model should generate the required results with minimal variability between simulation and actual results. Additionally, this model must be adaptive to reduce this variability. Studying the most known and used models in mining resulted in our work correlating Cunningham 2006, Swebrec, and CZM models. Thus, the Simfrag model was created, presenting a robust foundation and combining the most notable advantages of the aforementioned models.

Jan 21, 2025

By James Rowland, Marcia Harris, Richard Mainiero

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NO x ). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed.

Jan 1, 2007

By Ron Gilbert

Every day, demand increases with over all population; supply must follow. People must have more food, shelter, and mobility. Raw materials must be mined. Roads, trenches and foundations support the quality of life.

Jan 1, 1996

By Soseol Kim

A high-performance Emulsion-based booster explosives has been developed that can be used as a booster for bulk explosives. Currently, Pentolite booster, which is mainly used as a booster for bulk explosives, has a high risk of accidents due to the sensitivity of its raw materials PETN and TNT, and has a low melting point, making it impossible to use it in high-temperature ground. The Emulsion-based booster was developed to maximize the Velocity of Detonation (VOD) while elimination the shortcomings of the Pentolite booster. The VOD of the Emulsion-based booster is about 6,500m/s, so it can maximize the performance of the bulk explosive. In addition, it can be used in high-temperature ground and does not cause accidental detonation due to the external environment. In this article, the performance of the Emulsion booster was verifies through comparative test blasting of the developed Emulsion-based booster and Pentolite booster.

Feb 6, 2023

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Julijan Bratun, Joze Kortnik

Production of technical stone is an important economic branch in Slovenia. In 2009, we had 95 dolomite quarries, 27 limestone and 6 silicates quarries, according to the Ministry of Economic Affairs. Together they produced nearly 15 million tons of aggregates. The production in quarries is mostly performed with drilling and blasting method and only a minor part with other method like mechanical mining method.

Jan 1, 2011

By R W. Thomas

"This paper explores the possibilities of generating radical improvements in the drihing costs andproductivity of blastholes through the efforts of integrated teams as opposed to traditionalcustomer/vendor relationships."

Jan 1, 1996