Search Documents

By B Brown, P J. Hommert, B J. Thorne

"Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. A"" improved damage model based on microcrack growth in tension allows finite elementcalculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model."

Jan 1, 1990

By Dale S. Preece, Lee M. Taylor

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry.

Jan 1, 1990

By M. Hagfors

On the underwater testing of explosives, the measuring system consists of water filled test pond, tourmaline based pressure sensor, measuring cable and measuring unit, which supplies the DC current to the pressure sensor. Depending on the length of the measuring cable, it is always possible that some signal damping may occur in case the measurements are carried out without the signal amplifier to keep the measuring system as simple as possible. Therefore the length of the measuring cable should always be as short as possible.

Jan 1, 2006

By Rob Farnfield, William Birch, Douglas A. Anderson

In the blasting industry, even to the most safety conscious shotfirer, misfires are a constant source of concern. In the United Kingdom, there are two types of misfire, as classified by the Health & Safety Executive. Type A occurs when testing a shot before firing reveals broken continuity that cannot be rectified. However, due to the fact that a majority of quarries use non-electric initiation [i.e. shock tube] that cannot be tested, this type of misfire is very unusual.

Jan 1, 2016

By P D. Katsabanis

This chapter describes the principles for the derivation of the equations for a detonation wave. The importance of the equation of state for the detonation products is demonstrated and commonly used equations of state are discussed. Furthermore a brief introduction to the TIGER code is presented.

Jan 1, 1991

By W. J. Birch, R. Farnfield, L. Bermingham

Whilst a significant body of research has been carried into air overpressure levels that arise as a result of the use of explosives, few published studies have actually tried to relate the movement of a quarry face to the resulting air overpressure produced. The aim of this preliminary investigation was to monitor a number of quarry blasts at two different limestone quarries. The first using multiple separately initiated deck charges in a multi borehole blast, the second using single column charges in a multi borehole blast.

Jan 1, 2008

By P J. Dailey, S L. Burchell, R F. Chiappetta

In recent years, high-speed motion picture photography has become a powerful diagnostic tool and technique to study, analyze, evaluate, and aid in blast designs. Production blasting, typically lasting less than two seconds, requires an extended time base for observation and clarification of short-lived phenomena. Information obtained from high-speed photographic analysis is categorized into two main groups.

Jan 1, 1989

By Michael S. Wieland

This report focuses on the U.S. Bureau of Mines research regarding desensitization and malfunction of delay detonators and cap-sensitive explosives. Delay blasting in underground coal generates tremendous shock waves and rifting forces that fracture and heave coal. The shock waves from charge explosions radiate outward in all directions through the coal, impacting neighboring charges with later delays. The impact phenomena have debilitating effects, causing degrees of reduced charge performance ranging from misfires or weak detonations to out-of-sequence detonations. Impaired charges react poorly, fracture less coal, and produce fumes with higher toxicity. Coal-mine, underwater, and simulator tests were conducted to more thoroughly understand the shock damage mechanism. Recently the U.S. Bureau of Mines partially resolved the malfunction problem by demonstrating the feasibility of formulating a rugged explosive. This rugged cap-sensitive candidate passed the requisite tests for certifying an underground coal-mine explosive. With natural aging the formulation rapidly lost initiation sensitivity. The charge formulation had to be rebatched to finish the testing and therefore could not be certified.

Jan 1, 1992

By W B. Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire. Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1994

By A N. Gupta, C Joginadham, P Shiva Shankar

Cast boosters made with pentaerythritol tetranitrate(PETN) and trinitro toluene(TNT) give high velocities of detonation and are sensitive to initiation even under high pressures. However, the manufacture of the same involves heating of TNT to its melting temperature and mixing of dry PETN in it.

Jan 1, 1996

By Randy Wheeler

One of the more difficult topics to address concerns the effects of vibration on historic structures. Not only blast induced vibration, but also vibration from other transient and semi-continuous sources like, traffic, human activity, and environment forces. A common question might be, “What level of blast-re l a ted PPV is considered safe?” A review of some of the papers available from the ISEE Explosives Reference Database on CD ROM shows that 0.50 inch per second was often used. It was not clear on what basis this value was selected except that it represents the low frequency limit for plaster developed by the United States Bureau of Mines in RI 8507. In another case, a limit of 0.20 inch per second was mentioned, apparently simply because it was ten times less than 2.00 inches per second.

Jan 1, 2004

A simple and cost effective technique to increase fragmentation and burden velocities without making major modification to the overall blast design is with ALTERNATE VELOCITY LOADING OR BOOSTERING OF ANFO. The technique requires the placement of a cartridge or slug of explosive, having higher density and detonation velocity than ANFO, every few feet in an ANFO column. The greater the difference in density and detonation velocity of the Alternate Velocity Load to ANFO, the more pronounced are the results. Emulsions were selected as the Alternate Velocity test explosives because they detonate closer to ideal conditions than most other commercial explosives.

Jan 1, 1989

By Rob Famlield, Gavin Yuill, William Birch

The Blasting Research Group at the University of Leeds, in the United Kingdom, continues to be highly active in the area of the environmental impact of blasting. In recent years a major part of this research has been concerned with the use of linear superposition. This technique relies upon the assumption that all the holes in a blast produce identical vibration signals. Previous work at the University has shown that this assumption is not sufficiently robust to be generally applicable. This is due to a number of factors of which the key variable appears to be dynamic confinement

Jan 1, 2002

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By P D. Kasbanis, Lyall Workman

"The energy output of an explosive is typically calculated using an equation of state and computerapplications. Results are reported as weight and bulk strength, either in absolute terms or relative toANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of “available energy” associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated."

Jan 1, 1996

By Jarrod Bonsmann

"This paper presents the results of small scale testing to examine the effect of various importantparameters on the response of a vehicle due to the detonation of an explosive charge buried inthe soil below the vehicle. In particular, we were interested in examining what effect change instandoff distance, change in mass, and change in surface area would have on the loading applied.We examined the impulse delivered to the target in all cases and for the change in mass andchange in stand-off distance we examined impulse, kinetic energy, and acceleration."

Jan 1, 2012

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By Jeff Hiedeman, Clint Sestrich, Christopher Hyle

Westslope Cutthroat trout have declined in distribution and abundance across their range and currently occupy about 59% of their historic habitat. Due to hybridization with non-native species such as rainbow trout, genetically pure populations persist in only 10% of that range. A westslope cutthroat trout population with relatively high genetic purity (97%) and conservation importance persists in less than two linear stream miles in the headwaters of the South Fork Madison River in southwest Montana. The relative purity of this population has been maintained through the presence of a downstream intermittent reach. However, spring flows fill the intermittent reach, creating a connection between occupied westslope cutthroat trout habitat in the headwaters and the habitat of competing trout species downstream.

Jan 1, 2011

By Laurance A. Beck

Safety is the most important aspect of haul road design. Although other aspects of road installation enter decisions on design, the safety of persons using the road has to be foremost for the duration of haul road usage. Other aspects of mad design focus on minimizing truck cycle time and fitting haul roads to the long-term configuration of the mine/quarry or construction project. Roads are often installed at high gradients for a short-term goal, but the long-term benefits are easily shown with lower gradient haul roads which provide better cycle times and lower operating costs.

Jan 1, 1995

By V. Petr, G. G. W. Mustoe, T. G. Rozgonyi

We introduced a numerical method that is applicable for the analysis of static and dynamic deformations of elastic media. In this numerical study, each elastic body is modeled with a system of several hundred rigid particles that are joined together elastically. Maximum shear stress fields due to external loading are obtained and compared with those obtained by photoelastic experiment. Preliminary results are presented for the stresses generated in circular disk shaped bodies idealized with connected systems of particles. Extension of this simulation method to fragmentation of brittle materials is also illustrated in an example.

Jan 1, 2000