Search Documents

By Y. Hirosaki, H. Hamashima, Y. Itoh Kato, S. Tanaka

The emulsion explosives show non- ideal detonation behavior, and its detonation velocity can be controled by selecting the size and adjusting the quantity of voids involved. To establish the technology to control the detonation characteristics of the emulsion explosives, some experiments have been carried out using resin balloons of five different sizes ranged from O.OSmm to 2.42mm in the average diameter. Detonation velocities of the emulsion explosives containing resin balloons of different size and quantity were determined for the charge diameter of 20-50mm. The detonation velocity at infinite charge diameter was compared with calculated ideal detonation velocity. The emulsion explosives containing large (0.5mm or larger) balloons showed big discrepancy between the measured and calculated detonation velocities, and the fraction of ammonium nitrate reacted in the reaction zone was estimated to be significantly low. It was shown that the reaction zone length was proportional to the size of voids involved. The critical charge diameter was determined for the emulsion explosives containing different resin balloons at the various explosive densities. It is large for the emulsion explosives containing large voids, and it was shown that the critical diameter is proportional to the distance between the void surfaces, not to the void spacing, the distance between the centers of the voids. The reaction rate of the bulk emulsion matrix seems to be the major factor that affects the critical diameter than the specific surface of voids. Good relationship between the critical diameter and the reaction zone length was observed.

Jan 1, 2000

By Miie Shields, Ed Billington

Trail blasters for the National Park Service (NPS) live and work in remote mountain terrain throughout the western states, where any support or resupply may be sporadic and ditlicult and mountain weather affects every activity. Mechanical “aids” are the pick, shovel, rock-bar, wheelbarrow, and a Pionjar or Cobra dritl. The blaster is usually faced with an extraordinary range of work, t?om delay blasts in weathered rock using driiole depths of 18” (46cm) to as little as 4” (1 Ocm), through reducing boulders and talus fields to useable tread, blasting stumps, snags and log-jams, to the explosive disintegration and casting of animal czcasses. One day he/she might provide a 500cf (14 cu meter) anchor excavation for a suspension bridge, the next day directionally fall 60” (1.5m) diameter snags in a camp area, and the following day blast a 3-foot-wide (1 meter) tread bench across a steep bedrock slope. To be effective, the blaster must design each and every blast around desired end result, crew and public safety, maximizing effective use of limited quantities of explosive, and the minimnation of environmental effects. Since almost all drillhole blasting occurs in the weathered zone of the rock, blasting is more the art than the science of judging rock density, hardness, cohesion and prefracturing, and selecting explosives, drill and delay patterns, and loading techniques responsive to those conditions. For these reasons the NPS issues its own Blaster’s License, with a basic requirement of at least 40 hours of NPS blaster training and 3 years of supervised Blaster in-Training experience. The focus of this pre-license requirement is on safety and using explosives as a precision tool, versus just “blowing things up”.

Jan 1, 2002

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By P. Ross, O. Rielo, P. Katsabanis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. The paper reviews all available experimental information, ranging from small and medium scale tests in geologic materials to small scale tests at the laboratory and synthetic materials, simulating rock. Tests have been re-analyzed and discussed in terms of the information they present and the limitation of the testing environment in representing actual conditions. New results obtained from blasting experiments in specimens made of a grout have provided a clear picture of the effect of delay on fragmentation. The grout used has a strength of 60 MPa (8700 psi), density of 2.5 g/cm3 and P-wave velocity of 4000 m/s (13100 ft/s). Each block was placed in a yoke to eliminate unwanted reflections and the desired delay was obtained using the appropriate length of detonating cord between holes or sub-millisecond electronic detonators. Delays ranged from 0.1 ms/m (0.03 ms/ft) of burden to 16 ms/m (4.9 ms/ft) of burden. Fragmentation was obtained using screen analysis of the collected fragments. Delay time has been shown to be a significant parameter affecting fragmentation and back break. Generally larger fragments and less back break was observed at short values, while fragmentation somewhat deteriorated at significant delay times, compared to what was observed at intermediate delay times. The work is now extended to include the effect of energy partition on fragmentation as well as the effect of initiation point and coupling ratio.

Jan 1, 2014

By Kirlk Yeager

"Ammonium nitrate (AN) is commonly mixed with a wide variety of additives to produce specialty formulations. Two additives commonly utilized are sodium nitrate (SN) and sodium nitrite (SNi). Application of the nitrite is primarily limited to gassing of emulsions. The nitrate, however, is incorporated in a wide variety of formulations. The effect of both these materials on the thermal stability of AN was examined. Experiments initially utilized lab-scale testing methods (sub-milligram sample size), such as differential scanning calorimetry (DSC), with scale-up to cook-off analyses (16 g) eventually applied. Labscale testing indicated that the presence of SN and SNi (both at 5 wt%) produced no harmful effects on the thermal stability of AN. The cook-off results did not agree with those from the lab-scale analyses, with both SN and SNi creating tremendous thermal destabilization of AN. These effects were seen at additive levels as low as 0.1 wt%. When SNi was employed as the additive, cook-offs became violent enough to create explosions in the testing apparatus. Although SN did not create as spectacular a destabilization, it did lower cook-off temperatures to approximately the same level as SNi. The dangerous situation created by SN andSNi seemed to be limited to cook-offs conducted in sealed vessels. If the SN/AN or SNi/AN formulations were allowed to cook-off in vented vessels, the thermal destabilization of AN did not occur. These results seemed to indicate that even “trace” amounts of what might ordinarily be viewed as benign additives could create significant destabilization of AN-based explosives under proper circumstances. Conditions created by blocked pumps, or deep boreholes could well overlap those produced in sealed cook-off vessels. In addition to showing the hazards potentially created by “benign” additives, the study also stressed that experiments designed to evaluate thermal hazards must include duplication of field variables to the fullest extent possible. "

Jan 1, 1999

By Brian Stump, Rong-Mao Zhou

A series of single-fired (simultaneously detonated) explosions were conducted in an Arizona copper mine. The explosions spanned yields from 1700 to 13600 lbs (773 to 6169 kg) and were all detonated in an approximate 100 m by 100 m area. In order to quantify the effect of the mine free-face, the individual explosions were also detonated under three different emplacement conditions including at the free-face of the mine under normal burden, twice normal burden and fully contained. The purposes of these experiments were to investigate: (1) Generation of in-mine and regional phases such as Pg, Pn, and Lg from mining explosions; (2) Quantification of the relationship between yield and seismic amplitudes; (3) Quantification of the effect of confinement; and (4) Similarities and differences between single-fired waveforms and those from delay-fired explosions. Instrumentation was deployed at near-source (100-700 m) and in mine (1-5km) distances. Empirical scaling relations for the different shots in this test series were developed in order to quantify the effects of yield and confinement.

Jan 1, 2006

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By Orica Peru, Pedro Lozada

Maintaining a continuous mining process during thunderstorms is one of the primary challenges in Peru's open-pit mines. Safety protocols necessitate the establishment of exclusion zones to minimize the risks of unplanned detonations. During such conditions, loading and hauling equipment must be relocated or, in the worst case, halted, directly affecting productivity (t/h). Implementing a wireless initiation system mitigates the risk of unplanned detonations during electrical storms by eliminating the use of electrical cables that are susceptible to electrical discharge. This study documents the implementation of this system in a copper mine located over 3,500 meters above sea level in Peru, where electrical storms between December and March necessitate modifications to blasting schedules and limit the number of drills fired per event. Through a test using wireless detonators, a key performance indicator (KPI) was established to ensure safe and continuous operation during thunderstorms. The results were significant: 20 blasts were successfully executed, firing approximately 5,000 holes and moving around 10 million tons of material, all without safety incidents or critical operational deviations, achieving zero misfires and no scheduled blast suspensions. Shovels SH001 (ore) and SH002 (waste) continued to operate together for an additional 100 hours continuously during thunderstorms, generating a potential saving of USD 3.3 million by continuously sending ore to the plant during the testing period under stormy conditions. Additionally, the blasting initiation time was reduced by 25%, eliminating two activities that involved the use of surface connection cables. This reduction led to over 150 hours of decreased personnel exposure to interactions with vehicles and environmental hazards such as dust and noise. Furthermore, the number of holes fired in a single event increased by 50%, enhancing the blast tonnage capacity and reducing equipment stops due to evacuation and reentry from two to one.

Jan 21, 2025

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

By Mark S. Stagg, David E. Siskind

The Bureau of Mines arranged to have a wood-frame test house built in the pat of an advancing surface coal nine so it could investigate the effects of repeated blasting on a residential house. Structural fatigue and damage were assessed over a 2-yr period. The house was subjected to vibrations from 587 production blasts with particle velocities that varied from 0.10 to 6.94 in/s. Later, the entire house was mechanically shaken to produce fatigue cracking. Failure strain characteristics of construction materials were evaluated as a basis for comparing strains induced by blasting and shaker loading to those induced by weather and household activities. Cosmetic or hairline cracks 0.01 to 0.10 mm wide occurred during construction of the house and also during periods when no blasts were detonated. The formation of cosmetic cracks increased from 0.3 to 1.0 cracks per week when ground motions exceeded 1.0 in/s. Human activity and changes in temperature and humidity caused strains in walls that were equivalent to those produced by ground motions up to 1.2 in/s. When the entire structure was mechanically shaken, the first wallboard tape joint crack appeared after 56,000 cycles, the equivalent of 28 yr of shaking by blast-generated ground motions of 0.5 in/s twice a day.

Jan 1, 1985

By Paul L. Matrin

This paper will discuss the recent and on-going drill and blast optimization measures at the Sparkhule Limestone Quarry, which have resulted in a 44% reduction of drill and blast unit costs per ton of broken limestone. This amounts to approximately $240,000 of drill and blast saving per year at current annual production rates of about 2.5 million tons (2.3 million tonnes) total material shot. The reduction of drill and blast costs were accomplished by a detailed and controlled in-the-mine drill/blast experimentation and cost evaluation using 8 different blast pattern designs and shots totaling approximately 267,000 tons (242,200 tonnes) of shot and mucked material. A careful review of the geology of the deposit was performed to determine the different rock classification/strengths/structural properties and to adjust blast designs to optimize fragmentation for the different rock types. Equipment loading productivity and crusher throughput performance were monitored as part of the evaluation process to assure that an optimal fragmentation of broken rock was achieved with the new blast designs. The study included the review of bulk explosive and accessory selection criteria (ammonia nitrate/fuel oil mix - ANFO, mini prills (high density ANFO), sensitized and un-sensitized emulsions at a 30% emulsion/70% ANFO blend), blast pattern design, charge diameter and the cost of drilling. Laser profiling technology was used to assure proper bench heights, stemming and sub-drill footage and front row burdens. High speed photography, video and still photos were taken of the different designed shots to assist in the evaluation of the performance of each blast. Powder density checks, size distribution, back break, detonation velocity and pressure measurements were taken. Different borehole diameters were used for the drill optimization study and drilling cost and productivities determined. A detailed cost comparison between in-house blasting and complete shot service was prepared to evaluate if shot service is a cost effective alternative to current in-house loading and blasting including a review of the new and pending United States Bureau of Alcohol, Tobacco and Fire Arms (ATF) regulations and associated owner costs/risks and potential benefit of shot service.

Jan 1, 2004

By Richard Mainiero, James H. Rowland III

For many years there have been small scale tests available for evaluating the toxic fumes production by capsensitive explosives (DOT Class 1. l), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agents in construction and mining, there is a need to determine the quantities of toxic ti,tmes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pet) tieI oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/set for the 1 to 10 pet range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4~mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding 5 and 10 pet aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

Jan 1, 2000

By Ery Wardhana, Fathur Rozaq, Jeff Averett, Nella Lubis, Carl Lager, Herry Saputra, Rudolf Sitorus, Relinda Sanistrya, Hormat Sinaga, Andhiko Maharjono

Efficient drill and blast operations are crucial for achieving optimal fragmentation, productivity, safety, and operational efficiency for the mining industry. However, conventional methods face significant challenges, including manual borehole marking and retrieval by survey teams, limited real-time data monitoring, excessive borehole collar deviation affecting blast quality, suboptimal drill productivity impacting person-hours and fuel usage, subjective judgment by drill operators on voids during drilling, and limitations in explosive charging design that do not match rock hardness. Rock hardness determination using lithological data from exploration models is often inaccurate due to the interpolation effect of wide drilling distances and depths, necessitating manual field verification using drill cuttings and historical blasting results. Furthermore, using single-density bulk emulsion throughout blast holes leads to suboptimal results due to varying rock properties. This study introduces an integrated approach that combines smart drilling technology with advanced emulsion technology to enhance drilling and blasting efficiency. The method utilizes smart drilling technology with GPS for precise borehole placement, Measure While Drilling (MWD) loggers, and real-time performance monitoring. Additionally, it integrates a smart Mobile Processing Unit (MPU) featuring a digital system and an automated gassing system (AGS). This setup allows for multiple emulsion densities within a single blast hole, customized to match the hardness index parameters determined from MWD data, addressing the challenges in drilling and blasting operations. The study evaluates the effectiveness of this innovative approach through comprehensive field trials and data analysis. While maintaining the digging rate according to production targets, key metrics such as drilling productivity, drilling accuracy, fuel consumption, powder factor, drilling and blasting cost, and fragmentation size were compared between conventional and new methods. Results showed a 56% increase in drilling accuracy, a 23% increase in penetration rate, a 19.6% increase in drilling productivity, and a 29% reduction in fuel consumption. This new method decreased the powder factor by 5.2%, impacting the drill & blast cost reduction by 2.3%. Moreover, fragmentation size improved by 12.8%, demonstrating the effectiveness of rock hardness-adjustable emulsion density in achieving better blast energy placement. In conclusion, integrating smart drilling and advanced emulsion technology significantly enhances drilling and blasting efficiency. This approach offers substantial cost savings and operational improvements, providing a strong rationale for adopting this innovative method in drilling and blasting activities.

Jan 21, 2025

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By Michael Wieland

Work-principle computations for explosions underwater or in rock reveal the way the thermodynamic characteristics of surrounding material influence the resulting shock and heave. To reach total thermodynamic equilibrium under such transitory dynamic circumstances, reactions must quickly readjust to changing circumstances, which works for molecular (military) explosives where the fuel and oxidizer type atoms are originally in close proximity. For non-molecular mixtures with their dispersed zones of oxidizer or fuel, in particle or droplet form, there are numerous unproductive collisions, increasing the wait time required to reach chemical equilibrium. Underwater test data for molecular explosives compare rather well with the shock and heave resolved from the work-principal model, while the non-molecular explosives normally used in mining tend to yield a noticeable discrepancy. Years ago, it was recognized that the underwater shock was lower than expected and the heave was higher than expected for ammonium nitrate fuel oil (ANFO), though their resultant sum for the total work was roughly what was expected. When the readjustment of thermodynamic equilibrium warrants quicker chemistry than occurs in underwater or rock shooting, the time-retarded chemistry reduces the shock and raises the heave within the surrounding material without reducing the total work, unless the reaction retardation is quite severe. This technical complication in reality is a nonequilibrium issue that is difficult to resolve with just thermodynamics, though a rational set of transformation factors is formulated herein to represent those circumstances.

Jan 1, 2008

By S. M. Geerts, M. T. Wild

In this paper the performance effects of various shaped charge liner designs will be discussed. Several different charges will be tested and the liner design will be reviewed based on the performance in testing. The first type of shaped charge to be tested is a conical charge with dual confinement. For the purpose of this paper, dual confinement is a shaped charge with two liners but containing one explosive charge. Several charges with different dual confinement designs will be tested. Variations in configuration include charges with similar angle and similar diameter. The second type is a double conical shaped charge configuration. A double shaped charge will be considered to be two complete charges formed into a single cone. The goal of the project is to determine if any of the designs increase the efficiency and/or effectiveness of the shaped charge in comparison to the standard conical shaped charge. A standard conical charge will be detonated against a witness plate to get a standard depth of penetration or a baseline. All charges will have a seven cone diameter standoff, allowing the data to be compared to the control charge. Computer modeling will be used to predict the results of the testing that will be conducted. The actual results will be compared to the computer simulation for validation.

Jan 1, 2010

By Sami Kara, Marsel Nabium

As a mining project is developed from conceptual to production phases, there exists a variety of uncertainties and difficulties that affect the operation’s designs and economic values. A notable design parameter to be taken into account is the factor of dilution. Dilution is the waste material not separated from the ore in the stages of mining and is sent to the processing plant. It is defined at the ratio of tonnage waste mined and sent for processing over the combined ore and waste tonnage milled. Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programs require interaction on a multidisciplinary level. This paper outlines recent initiatives undertaken at Polysmetal Silver Magadam Mine to reduce dilution and increase revenue. This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution. The mining companies put a lot of effort into extracting lower grade while minimizing cost. The dilution control assists with achieving this goal. In Polymetal Silver Magadam Mine we succeeded to control more than 20 blasts by keeping almost the same grade measured in the face. The results indicated that using the adequate blasting timing design can help to separate the ore from the adjacent waste in drift blasting with different ore body configuration.

By María Virginia Ramírez, Alejandro Alarcón, Alea Reyes

Reactive grounds (presence of FeS2, CuFeS2) can create hazards in a mine; misfires to premature deflagration or detonation of loaded blast holes. This occurs because some minerals can react to ANFObased explosives. Due to a high potential event that occurred in The Mine in 2013, The Mine and the Explosive Provider (“The Company”) are conducting a soil characterization of the areas containing reactive sulfides. This study was planned along with The Mine and it is being developed by a multidisciplinary team.

Jan 1, 2018