Search Documents

By L. M. Lopez, J. A. Sanchidrian

This work investigates the performance of some of the measurement techniques used in vibrations from blasting monitoring. Two tri-axial geophones with cases of different size, shape and mass were tested in a shaker table. The geophone cases were mounted in three different ways on a granite slab fixed to the plate of the shaker: freely placed, sandbagged, and anchored. A known horizontal periodic motion of constant amplitude, and frequency from 16 to 200 Hz, was applied to the slab. Two amplitude levels of 5 and 20 mm/s (0.2 and 0.79 in/s) were applied when the sensors were sandbagged or anchored and only 5 mm/s when no holding force was applied. The transmissibility of vibrations from the rock to the longitudinal geophone as function of the frequency (i.e. ratio of response of the geophone to the slab motion) has been obtained for each measuring condition tested. The transmissibility is considered a composition of the transmissibility of the rock-to-sensor coupling and the transmissibility of the sensor’s mechanics and electronics. The transmissibility of the coupling is obtained normalizing the total transmissibility with the transmissibility of the seismographs, obtained by a suitable test to which a coupling transmissibility of 1 is assigned. Geophone-to-rock coupling is a resonant phenomenon that may alter the amplitude of the measured waveforms by a factor of 1.2 to less than 0.6. The most accurate and precise measurements are obtained with geophones anchored to rock. On the contrary, freely placed or sandbagged sensors are non-predictable planting conditions that lead to high amplification or damping in most of the frequency band analyzed. It is also shown that existing acceleration criteria to select coupling methods do not necessary lead to good quality (accurate and precise) vibration data.

Jan 1, 2014

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025

By C. K. McKenzie

Presents outline of flyrock model and a field procedure to validate predictions of maximum projection distance. Field results are presented from 13 field tests with two different hole diameters.

Feb 1, 2020

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By Muhammad Yamani, Marsell Riviera, Herry Saputra, Rizky Amin

Drill and Blast processes in hot and reactive ground conditions are a severe challenge in mining, especially in the blasting process. Our main objective is safety issues without compromising the blasting outcome. Safety concerns include unexpected detonation, product damage, and misfire. However, apart from the issue of blasting safety, it is also crucial to maintain good results such as fragmentation, loader productivity, and ore dilution control. Therefore, we use a different product selection method to produce a safe and efficient blast. Pit Araren is one of the pits of the Tokatindung Gold Mine Project in North Sulawesi Province, Indonesia, classified as hot and reactive ground conditions that range from elevation of 25mRL temperature could reach to 98⁰C (208,4⁰F) based on actual measurement. The previous practice for blast holes with temperatures above 70⁰C (158⁰F) loaded with the primer that was specifically designed for hot and reactive ground conditions consisting of detonating cord and packages emulsion that specifically formulated to inhibit exothermic reaction then tied in with a combination of non-electric surface delay detonator and detonating cord initiator (short length non-electric surface delay detonator housed in plastic connector).

Feb 6, 2023

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling.

Feb 1, 2020

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By S S. Kahlon

India is a large and growth market for explosives and accessories, which has dramatically changed from complete import dependence to self sufficiency, and now has an exportable surplus. The largest single user is coal mining which is continuing to show a healthy growth with opencast mining becoming increasingly dominant. The explosives industry has kept pace with mining and today all the well renowned explosives technologies of the world are available in the country. While slurry explosives are popular in large diameter, NG based explosives continue to be preferrred in small diameter usage. Emulsion explosives have had a good market response. ANFO usage is limited due to local reasons. As the mine size is increasing, the demand for bulk-on-site explosives is growing. Prices of explosives and accessories are cheap compared to international levels. The user industry is mainly Government owned mines whose profitability is not satisfactory. Explosives industry is over licensed in terms of manufacturing capacity, which is likely to put pressure on the viability of some of the explosives manufacturing units. Scope exists for optimization of blasting parameters through the use of computerized blasting models. The explosives industry is faced with new challenges and opportunities.

Jan 1, 1987

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

Investigating blast vibrations typically utilises scaling and attenuation models for prediction of vibration amplitude over a range of charge weights and distances. A number of generalised relationships have been established from many years of far-field data analysis, where small changes in charge weight and ray-path distance are less critical. Under far-field conditions, small variations in local geology or geometry do not significantly affect the vibration scaling behaviour over an expected range of data. In the near to intermediate-field (less than 5 times the explosive charge length), small variations in wavepath and rock mass conditions between a blast and a monitoring point can greatly affect the outcome of vibration modelling. This case is especially true for underground blasting in sublevel open stoping, where the paths of blast-induced vibrations regularly encounter voids and preconditioned ground.

Jan 1, 2010

By Bethany Witter, Dyno Nobel

In the past decades, a technological explosion has caused generational shifts. First, millennials experienced a technological shift to computers and cellphones. Next, Generation Z experienced a shift to smart phones and social media. These two generations are immersed in technology and are accustomed to constant connectivity. How do the extractive and construction industries gain the interest of younger generations and integrate them into the industry?

Feb 1, 2020

By Bethany Witter

In the past decades, a technological explosion has caused generational shifts. First, millennials experienced a technological shift to computers and cellphones. Next, Generation Z experienced a shift to smart phones and social media. These two generations are immersed in technology and are accustomed to constant connectivity. How do the extractive and construction industries gain the interest of younger generations and integrate them into the industry? The Virginia Tech Student Chapter of the International Society of Explosives Engineers handled this same issue with its recruitment efforts and event planning from 2017-2019. The first critical component of integrating Generation Z college students into the extractive industries is clear and frequent communication via email. Next, Generation Z often values the motivation behind work when choosing a career, so advertising technological advancements, benefits, and ways people can contribute to improving the industry also helps attract young generations. Similarly, advertising opportunities for people to work outside with their hands, travel, and secure stable careers can attract students. At Virginia Tech, the most effective way to attract and maintain the interest of students in extractive industries is to put the students in the field. Field trips to mines and factories experienced the most stable attendance and highest survey reviews of all other chapter events. Guest presentations from industry professionals were often well attended, but attendance tapered off as the academic year progressed and students grew busier. Periodic trips throughout the year maintained student engagement and often supplemented their curriculum. The student chapter was relatively successful in attracting students, but it struggled to maintain attendance levels in the latter portion of the academic year. In the future, the industry can increase its recruitment of Generation Z and Millennials into the workforce by working more closely with university programs to provide resources and opportunities for hands-on experiences for students.

By Jonathan D. Aubertin

The unique nature of rock salt blasting is compared to traditional hard rock practices. Rock salt geomechanical nature is discussed in the context of rock blasting events. A cratering mechanism prevalent in soft rocks is presented and exemplified through a series of single hole blast tests performed in salt deposits.

Feb 1, 2020

By Wesley L. Bender, James E. Murray

Pre-blast surveys are often conducted solely to document existing structural conditions and uncover potential problem areas. This paper presents a case history where the pre-blast survey was also used as a vehicle to initiate a public relations program with the occupants of a large apartment complex adjacent to a major excavation site. The public relations program, in conjunction with good blasting practices, succeeded in keeping complaints to a minimum. The presentation includes an overview of the project, details of the public relations program, some of the blasting methods that were utilized and a recap of the complaints received.

Jan 1, 1988

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Blenda Lopes, Rodolfo Matias, Vagner Paixão, Vinicius Leão VALE, Edivarde Sousa

Seismography is an extremely important subject in the context of rock blasting, especially in the current scenario, which involves the need for increased controls due to the growth of urban areas near open-pit mining operations. Worldwide, communities are becoming increasingly aware of the environmental and social impacts associated with mining activities. Therefore, maintaining good relationships with these stakeholders is essential to preserve the social license to operate and to comply with current legislation. This situation is exemplified in an open-pit iron mine near the capital of Minas Gerais, Brazil, where the community is located less than 40 meters from the pit boundaries. Blasting activities within the mining area occur at distances less than 500 meters from the nearest community, making continuous seismograph monitoring necessary to ensure that operational conditions are maintained without compromising exploitation efficiency. The threshold for peak particle velocity, according to Brazilian Standard 9653:2018 by ABNT, is 15 mm/s at frequencies around 4 Hz. However, even though the peak particle velocity commonly registered was inferior to 3 mm/s, there were still complaints from nearby residents regarding human discomfort. To further reduce vibration levels, a study was conducted to implement a new blast design, considering factors such as reducing bench height, altering the hole delays, maintaining the maximum charge per delay, and adjusting the drilling pattern without negatively affecting rock fragmentation quality. Following the implementation of the revised blasting parameters, seismographic measurements in the region decreased to below 0.6 mm/s. This significant reduction in ground vibrations contributed to minimizing community disturbances and fostering a more positive relationship between the company and its surrounding residents.

Jan 26, 2026

By D. Scott Scovira, Rick Webber

The Iron Ore Company of Canada [IOC] is a global leader in Arctic mining applications, and the blasting crew have something to be very proud of. On Wednesday 21 Dec 2005 at 3:28 PM the largest single bench blast in the company history was detonated. The successful firing of this 5.0 million tonne [5.5 million ton] blast surpassed the previous company record of 3.8 million tonnes [4.18 million ton].

Jan 1, 2008

By Pierre DePasquale, Ricardo Chavez

Lowering of quarry energy consumption participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry. Within this global quarry project, blast design, as the first link in the chain, has to be optimized in order to satisfy requirements of downstream operations. The authors have been developing and implementing an operational methodology using continuous field measurements and field adaptation methods for blast design. It drives the drilling and blasting work, aiming at a more energy efficient and environmentally friendly operation. Based upon actual local conditions (rock-mass assessment, face geometry, borehole deviations, etc.), blast patterns are optimized through a specific hole-by-hole blast design software. It provides a better and more consistent energy distribution, to achieve a better rock fragmentation, while avoiding explosive overconsumption. The software also calculates total energy inputs and the drilling and blasting contribution to Greenhouse Effect. Coupled with methodical fieldwork and variable density explosives, it has been leading to a real reduction in energy costs and greenhouse gas emissions. As the project is now reaching its final stage, demonstrations were conducted in various quarries around Europe. Several simulations were carried out and compared to the site data, in order to propose enhancements for the different phases (extraction, loading, hauling, crushing and transport) while bearing in mind the environmental impact of the quarry. This blasting methodology allows to assess the carbon footprint of drilling and blasting in conjunction with the downstream operations, thus to evaluate the global carbon footprint of quarrying. Copyright ©

Jan 1, 2015