Search Documents

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By C. A. Acuña

Extensive literature exists on the motion of single bubbles and the behaviour of swarms of bubbles. This contribution describes work to track and reveal the motion of individual bubbles in a swarm. The technique is based on high speed cinematography and tracking of multiple moving objects. Image processing algorithms were implemented in Matlab to isolate and measure geometric proper-ties of the bubbles in image sequences recorded at 2 ms interval; and these properties were compiled into a data structure. To track a bubble, the geometric properties and a matching criterion were applied on consecutive pictures to identify the bubble. The bubble trajectory was reconstructed from the data structure for the matched objects. The methodology is briefly described. The new technique was tested for bubbles produced at slot-type spargers (i.e., approximately 2-D swarms) in the presence of two frother types ('strong' and 'weak'). Two observations are discussed: a) that bubble motion in a swarm describes a velocity-size relationship dictated by the dominant bubble size class; and b) that surfactant type influences bubble rise velocity for bubbles in the range 0.1 mm to 4 mm. The latter suggests surface viscosity rather than surface immobilization determines bubble rise velocity.

Jan 1, 2014

By G. Voiloshnikov, A. Bogudlova

"The deleterious effect of carbonaceous matter during cyanidation of gold ores (so called preg-robbing) has been recognized for many years. Based on this, a new method using flotation to reduce the content of carbonaceous matter was developed. Low-sulfide gold-bearing ore with carbonaceous matter of 0.14% from a Russian deposit was processed. The purpose of these tests was to compare two flow sheet options. Option I comprised removal of carbonaceous product prior to sulfide flotation. Option II comprised removal of carbonaceous matter from flotation concentrate. It was found that the content of carbonaceous material can be reduced in sulfide gold-bearing concentrate prior to leaching. High gold recovery was observed during the separation of carbonaceous material prior to sulfide flotation using Option I. Due to lower reagent consumption the costs for reagents were decreased using Option II. The results have shown the effectiveness of a new method. Patent No. 2783808 was obtained for removal of carbonaceous material prior to sulfide flotation. This information will be used to design a large processing plant flow sheet in Russia."

Jan 1, 2014

By R. Venugopal

The paper reviews the development of Mineral Engineering education and training programmes in India. It highlights the major academic programmes and describes the evolution of the curriculum and design of courses in response to the changing requirements of India?s mineral and coal industries. An outline of the efforts needed to sustain and further improve the existing programmes is also provided. Keywords: manpower, mineral engineering

Sep 1, 2012

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By Raquel Franco de Souza Lima, Isao Matsuoka

"Microflotation studies and abstraction experiments were conducted with synthetic oxide spinels relating to chromite (MgCr2O4, FeCr2O4, FeFe2O4 and FeAl2O4), using sodium oleate as collector. An attempt was done to correlate this data with the speciation of oleate in the bulk solution and at the interface solid-water, to explain the floatability curves. The microflotation tests were conducted using a microflotation cell. The abstraction of sodium oleate was measured at 25°C, with one gram of synthetic spinel and the abstraction time was 30 minutes. After centrifuging, the residual oleate concentration in the supernatant was measured by using the spectrophotometric method described by Mizuniwa et al. (1977), that covers the range from 1.5 to 9 ppm. To cover the range from 0.2 to 1.5 ppm, the residual oleate concentration was measured using the spectrophotometric method described by Gregory (1966). The amount of oleate abstracted was calculated from the difference between initial and residual (equilibrium) concentrations.Figure 1 shows the floatability of FeCr2O4, FeAl2O4, FeFe2O4, MgCr2O4 as a function of pH and sodium oleate concentration of 1 x 10-5 M. The IEP of each sample is indicated in the figure by a vertical line in the horizontal axis. The chromium-bearing spinels FeCr2O4 and MgCr2O4 show the lowest isoelectric points (IEP), around pH 6, while in the case of FeFe2O4 and FeAl2O4, the isoelectric points lie at pH 6.5 and 7.3, respectively. It is seen that the flotation-pH curve for FeFe2O4 has a peak at the pH of the IEP, while flotation peak for FeCr2O4 appears at pH below the IEP and that of MgCr2O4 does at pH above the PZC. On the other hand, FeAl2O4 is floated at pH range between about 4 and 7,3 (IEP). This suggests that the pH value at which the maximum flotation occurs is dependent on the sort of spinel to be floated, though it appears in the vicinity of the respective IEP."

Jan 1, 2003

It is well known that the crushing and grinding steps in the mineral processing of ores represent a substantial proportion of total energy, cost and carbon emission in mining. For instance a recent study calculated that 36% of the energy consumed by gold and copper producing mines in Australia was attributable to comminution (Ballantyne et al, 2012). Understanding this component of a business is essential in a world seeking to lower production costs, improve earnings and reduce its carbon footprint. The issue commands the attention and support of industry leaders in the mining sector, government, equipment manufacture, engineering design and research organizations. Furthermore, several researchers have often stated that globally, comminution processes consume between 3-4% of the world?s electrical energy production (Daniel and Lewis-Gray, 2011). In 2009-10, Australia?s Federal Government Energy Efficiency Opportunity (EEO) participants in the mining sector used 336.5 PJ, representing approximately 6 percent of Australia's total energy use. It is evident that the current practices of breaking rocks in tumbling mills are relatively inefficient (Fuerstenau and Abouzeid, 2002). Research and improved engineering design has established that a range of improved blasting, crushing and grinding techniques and flow sheets may lower project costs and carbon footprint. These include relatively simple process flow sheet strategies such as gangue rejection or pre-concentration prior to size reduction, a better combination of grinding technologies (both current and new systems), and selection of coarser grind sizes where ore and waste mineralogy allow. Yet, despite this systematic and detailed research, the industry remains somewhat reluctant to implement these strategies. CEEC (Coalition for Eco-Efficient Comminution) was established in 2011 to support knowledge sharing and change in an area of high-energy consumption for the global mineral industry. CEEC is a not-for-profit industry company, funded by grants from world wide industry companies, whose mission is to accelerate knowledge and technology transfer in the field of energy-efficient comminution. The key benefit to the mining sector arising from CEEC?s activities will be an increase in the rate at which more energy-efficient comminution data sets, processes, and technologies are developed, demonstrated, shared and applied. This will contribute directly to the industry?s target of reducing operating costs and carbon emissions. CEEC International Ltd and JKTech Pty Ltd teamed together to facilitate the inaugural CEEC Workshop, in June 2012. The purpose of the workshop was to produce a roadmap to provide guidelines for how (1) operations can achieve best EEC practice in the short to medium term, in collaboration with vendors, engineering companies and other service providers, and (2) what R&D is needed to achieve paradigm change in EEC in the medium to long term, e.g. 75% reduction in comminution energy in 10 years.

Sep 1, 2012

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

This paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.

Jan 1, 2003

By N. Dhawan

In the last decades, High Pressure Grinding Roll (HPGR) has gained significant importance in hard rock processing due to numerous metallurgical benefits such as energy savings, particle weakening, preferential damage of coarse particles, and preferential comminution-liberation. There are a limited numbers of lab-scale HPGR units throughout the world. The laboratory-scale HPGR machine at the University of Utah is first-ever lab-scale machine designed by late Dr Klaus Schönert, the inventor of HPGR. This HPGR is constructed with two counter-rotating hardened tool steel rolls, each 200 mm in diameter and 100 mm in width. The HPGR unit is equipped with eight sensors and a robust control system, which serves as an ideal system for fundamental studies and lab-scale testing. In HPGR operation, throughput, energy and product size distribution are intricately linked to specific grinding pressure, roll gap and rolls speed. The nip angle existing during the operation determines the volume of feed material above the rolls that is pulled into rolls without slip. In this paper, scale-up factors and some of the existing models have been reviewed. A number of experiments have been carried out with limestone and a slag material. The influence of operating variables and their complex relationship has been studied.

Sep 1, 2012

By Ye Junjian

The feed ore is the concentrate of low intensity magnetic separation of pyrite tailings, containing TFe47.47%, S19.41% and SiOpyrrhotite. The exploratory tests showed that using a process of flotation followed by magnetic separation could respectively obtain a sulphur concentrate of S 31.08% with a recovery of 82.89%, and an iron concentrate of TFe 59.97% and S 9.52%with a recovery of 30.93%. The reason of iron concentrates with high sulphur grade was that the sulphur grade of flotation tailings was 7.03%. So enhanced flotation for pyrrhotite was investigated in this research. Results show that when the natural pH of ore pulp varied from 5.5 to 6.0, a reagent combination of FS, LH, and BJ displayed the optimum flotation performance for pyrrhotite. After comparisons made on different flotation processing, the previous flotation flow of ?one roughing, one cleaning, one scavenging system and middling reprocessing?, was found, among others, to have the best flotation effect, as the grade and recovery of sulphur concentrate were 31.08% and 82.89%, respectively, and sulphur content of the flotation tailings was 7.03%. The above results indicated it was difficult to raise further the effect of flotation desulphurization. The authors therefore suggested that oxidizing roast should be adopted following the magnetic process for the purpose of further desulphurization. Besides, flue gas containing SO2 8.25%. And the valuable minerals are magnetite and 2 generated from roasting could be reused for sulphuric acid production. Keywords: pyrrhotite, enhanced flotation, desulphurization

Sep 1, 2012

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By M. Lak, M. Asghari, M. Saghaeian, R. Hejazi, A. Haratian

"Magnetic separation techniques are used extensively in mineral processing operations. Magnetic separators are robust and relatively easy to operate. As the ore get hard and low grade, fine grinding must be required mostly to allow for a high degree of mineral liberation. These processes encounter the magnetic separation process difficulty due to a significant change in the separation behavior of particles. This study investigates the effectiveness of a novel proven wet magnetic separator for the beneficiation of Lebedinsky (Russia) iron ore achieved through developing pole arrangement and tank design. Basis on the results of multiphasic simulation of a medium intensity magnetic separator (MIMS) and dense media tank using Magnetic Design Software, a new model of the MIMS separator was developed. The main of the new MIMS separator was focused on improving separation and the decreasing the number of separators in cobber stage of the plant. The new MIMS separator was tested into a pilot plant on the received samples from Lebedinsky iron ore plant. In addition to the basis on the results of the modeling, promising results of test work and previous experiences, it was claimed the unit capacity of new separator is 33.33% more than the existing separator that could decrease the number of separators. In addition, the significant energy saving in the same operational condition could be obtained without any important adverse effect on the final concentrate quality.INTRODUCTION Magnetic separation is a long-established method for the purification and removal of substances from fluids (Augusto et al., 1999; Buck et al., 2015; Hoffmann et al., 2002; Lauda et al., 2016; Lindner et al., 2010; Podoynitsyn et al., 2016; Rashidi et al., 2016), mainly in mining processing industries ranging from steel production to coal desulfurization as commercial technology (Andres, 1994; Augusto, 2002; Svoboda, 1987). High gradient magnetic separation as an effective method for recovering of weak and fine magnetic particles separation has undergone dramatic developments, and has also achieved extensive application during this time (Svoboda and Jujita, 1987). Magnetic separation operations can be categorized into high intensity as electrical (up to 20,000 gauss), Medium intensity (2000-5000 gauss) and low intensity (less than 2000 gauss) techniques. Magnetic separators offer a simple, clean and economic way to sort magnetizable ores and minerals. After pulverization, the material is run through an inhomogeneous magnetic field, where particles of different susceptibility experience different magnetic forces. The force increases with susceptibility, magnetic field and field gradient (Jongst et al., 1984).In magnetic separation, the difference in the susceptibilities of the various particulate materials is used to separate the material flow into two or more products (Wasmuth and Unkelbach, 1991). The magnetic force acting on a particle can be calculated using the following equation:"

Jan 1, 2018

By J. R. Cui

The production of electric and electronic equipment (EEE) is one of the fastest growing areas. This development has resulted in an increase of waste electric and electronic equipment (WEEE). In view of the environmental problems involved in the management of WEEE, many counties and organizations have drafted national legislation to improve the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. Recycling of WEEE is an important subject not only from the point of waste treatment but also from the recovery of valuable materials. Consumer electronic equipment (brown goods), such as television sets (TV), radio sets, and video recorders, are most common. However, recent work on recycling of waste electric and electronic equipment (WEEE) primarily focused on personal computer and printed circuit boards scraps. Based on a detailed characterization study of consumer electronic scraps, recycling of TV scraps oriented to recovery of metals is highlighted by utilizing air table separation, eddy current separation, and optical (metal) sorting process. The result indicates that a high recovery of copper could be obtained by utilizing an effective gravity separation process. The separation results reveal that air table separation is an effective technology to recover metals from consumer electronic scraps. By using a DGS table, approximately 90% of non-ferrous metals were recovered in the heavy product with a purity of 40%. Printed circuit boards and cables in TV scrap cause metals loss due to the fact that metals in printed circuit boards and cables are not liberated from plastics and ceramic materials. The study shows that eddy current separation and optical (metal) sorting process provide alternatives for recovery of metals from shredded TV scraps.

Jan 1, 2014

By A. V. Kozub, D. O. Sharkovsky, R. I. Ismagilov

"Due to complex mineral composition and fine ingrained nature concentration of iron ores deposited in Mikhailovskoye mine field requires application of wet magnetic separation to produce 65–66% Fetotal and 8.2–8.6 %SiO2, concentrate with 90–94% of material being –0.044micron grain size. Higher specific consumption of ROM, increase of production costs with concurrent reduction of output - those are inevitable side effects of desired concentrate grade improvement. Large-scale complex analysis and surveys have been carried out aimed at concentrate grade improvement with concurrent output increase. Classification of feed in hydraulic cyclones (hereinafter referred to as hydrocyclones) has been the bottleneck for improvement of processing throughput and concentrate output. Hydrocyclone classification efficiency is 50-60% and further improvement is practically impossible. Actual circulating load may achieve as much as 500-600% while the optimal rate is 200-250%. Application of wet fine screening has been considered to improve iron ore concentrate grade. Objective of this work is to design processing flow diagram for unoxidized ferruginous quartzites with implementation of wet fine screening. Large-scale tests have been run in Crushing and Concentrating Plant with application of wet fine screening stage. These tests included application of wet fine screening in 2 and 3 stages of classification to separate desired grain sized material; replacement of hydrocyclone classification with fine screening; application of fine screening as additional stages to concentration process and screening of final concentrate. Testing Methods. EXPERIMENTS AS WELL AS THEORETICAL RESEARCH HAVE BEEN APPLIED FOR THE PURPOSES OF THIS WORK; INCLUDING MAGNETIC, GRAIN-SIZE AND CHEMICAL ANALYSIS OF CONCENTRATION PRODUCTS. MODERN ANALYTICAL DATABASE HAS BEEN APPLIED TO STUDY WET FINE SCREENING FEATURES, MINERAL AND PHYSICAL COMPOSITION OF CONCENTRATION PRODUCTS. Work Results: - analysis of wet fine screening application for iron ore concentration. - technological solutions enabling to improve slurry classification of fine ingrained low magnetic iron ore have been developed. - effective process flow diagram including fine screening has been designed based on the feasible and reasonable arrangement solutions."

Jan 1, 2018

By Ana Elisa Casas Botero

The Rhodococcus opacus microorganism was evaluated as a biocollector for flotation of barite. The electrophoretic behaviour of the mineral, before and after R. opacus interaction, was evaluated and showed that the cells adhesion shifted the mineral zeta potential curves. Adhesion tests were suggested a high affinity of the bacteria for barite. The experiments of the adsorption rate of the R. opacus on the mineral surface showed fast kinetics, achieving a maxim of cell adsorption after 5 minutes. Adsorption isotherm curves for barite could be categorized as Langmurian (L) type II. The best bioflotability results for barite achieved values around 75% for a R. opacus concentration of a R. opacus concentration of 250 ppm in the pH around 5.0. The studies were compared with the flotation of barite using a traditional collector. The bioflotation experiments were discussed considering the obtained adhesion tests. The results were supported by the Thermodynamic approach for selected pH values. The fundamental flotation studies showed the paramount potential that R. opacus presents as a biocollector and its possible application in the mineral flotation industry.

Jan 1, 2014

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By V. A. Chanturiya

The application of High-Power Nanosecond Electromagnetic Pulses (HPEMP) irradiation in dressing of resistant gold- containing ores appears attractive as this technique provides for a significant increase in precious metal recovery (30-80% for gold and 20-50% for silver), therewith helping reduce both energy consumption and the cost of products. The prospects for applying pulsed power technologies in the mineral processing in order to increase the contrast between the flotation properties of raw minerals dictate the need to perform special studies of the effect of HPEMP on the structural state, phase composition, and physical and chemical properties of surfaces of sulfide minerals as the main carriers of precious metals. This study deals with plausible mechanisms of the micro- and nanophases formation on the surfaces of sulfide minerals under the effect of high-power nanosecond electromagnetic pulses (HPEMP) with high electric field strength ~107 V/m. This paper discusses reasons for the changing of flotation behavior of natural pyrite and arsenopyrite during the pulsed-power treatment. It was concluded that HPEMP treatment may be regarded as a tool to change the surface composition and sorption ability of collector (xanthate) onto mineral surface, and, therefore, it allows to control the hydrophobic-hydrophilic surface balance. Single mineral flotation tests have been shown the significant increasing of the pyrite recovery while the arsenopyrite was depressed. The results of gold containing pyrite (pyrrhotite)-arsenopyrite ore flotation in batch approve the decreasing of arsenic recovery in sulfide concentrate. Keywords: pyrite, arsenopyrite, high power nanosecond pulses, activation, selective flotation

Sep 1, 2012

By I. Dymov

"The extractive metallurgy of precious metal ores involves gravity concentration, flotation and cyanide leaching. Pre-oxidation, such as roasting, autoclaving, bacterial oxidation and other techniques, is required for processing refractory ores. Selection of the process is mainly driven by the grade, reserve and mineralogy of the target elements. The concentrations of precious metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. The objective of geometallurgy and process mineralogy is to reduce and minimize the technical risk in project evaluation, process selection, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical characterization and metallurgical testwork. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes, while mineralogy is one of the major predictive and trouble-shooting tools for many new mineral projects and operating mines. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy and highlights the importance of both disciplines in process selection and plant optimization with applicable case studies. INTRODUCTION Precious metals, including gold, silver and platinum group elements (PGE) occur in various geological settings and ore types. The concentrations of these metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. Process selection is most important in any precious metals project and is mainly driven by the grade, reserve and mineralogy of the target elements. Free-milling ores, such as Kupol in Russia, Hemlo in Canada, Grasburg in Indonesia, UG-2 in South Africa, Lac des Iles in Canada, and Noril’sk in Russia, can be processed using flotation or cyanidation with or without gravity. B2Gold Corp, a Canadian gold company, just started a number of new and under construction free-milling gold operations such as Fekola mill in Mali, Mastbati mine in Philippins and Otjikoto mine in Nambia. However, refractory ores (particularly gold ores), such as the Carlin and Goldstrike mines in the USA, Giant in Canada, Pueblo Viejo in Dominican Republic, Porgera and Lihire in PNG, Kittilla in Finland, Fairview in South Africa and Shuiyindong in China, must be processed using pre-oxidation prior to cyanide leaching. In some mildly refractory gold ores, such as Kumtor mine in Kyrgyzstan and KCGM in Australia, ultrafine grinding is required to liberate fine-grained gold particles. For some gold ores containing both free-milling and refractory components (such as Cripple Creek mine in Colorado, USA), two or more recovery processes may be required. The variability of grade, metal deportment, ore hardness and other parameters is one of the risks that encountered in development and operation of many precious metals projects. To minimize and reduce the technical risk caused by ore variability, geometallurgy and process mineralogy have been used by mining companies in the last two decades to measure and quantify the spatial variability of the deposits that are being developed. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy, it highlights the importance of both disciplines in process selection and plant optimizat"

Jan 1, 2018