Search Documents

Coal preparation plants usually operate with water in a closed circuit mode. In this practice, large quantities of water is continuously being recycled. To compensate the natural losses, only small quantity of fresh make up water is added into the circuit. As a result, a gradual build up of residual concentrations of flotation reagents (frothers, collectors, coagulates etc.) take place in the water and the concentration levels of the contaminants increase. Besides, the recycled water accumulates higher amounts of total dissolved components (1600 ppm) and hardness (740 ppm) than the fresh water. Nearly 80 ? 85% of the process water used in a coal preparation plant is utilized in treating the coal fines in flotation circuit. The presence of certain alkali earth metal ions (e.g., Ca++, Mg++) may adversely affect the flotation performance as they precipitate sparingly soluble hydroxyl complexes on the coal surface and change its surface charge. These studies showed that the use of recycled water in flotation has a significant effect on the selectivity and kinetics of the flotation process because, the dissolved compounds, both inorganic and organic, alter the chemistry radically. By treating the recycled water through a softening process, the concentrations of alkali earth metals and hardness were reduced significantly. The concentration of alkali earth metals and hardness were reduced to 10 ppm and 35 ppm respectively in the softened recycle water. From the selectivity studies, it has been observed that the flotation yield and recoveries increased by four to seven units by softening the recycled water. The kinetic studies indicated that the clean coal particles followed first-order kinetics. The kinetic parameters namely, flotation rate constant (k) and maximum recoveries (R8) of flotation, were found higher with softened recycle water than the recycled water. This reduces the residence time in the flotation cell and thereby, increases its productivity. Keywords: coal flotation, hardness of water, water chemistry, softening process, selectivity, kinetics, flotation rate constant and maximum recovery

Sep 1, 2012

By Mike Daniel, Eric Wang

"Several new large copper and gold concentrators have been built and commissioned around the world in the past five to eight years. The success of the ramp-up from these very large concentrators has varied. CITIC SMCC Process Technology was engaged to assist some of these mines by gaining a better understanding of the factors that influence throughput capacity. As such, site-specific throughput forecast models that are influenced by SAG mill performance were developed. The forecast models are easy to interpret and modify and can greatly assist the mine management to make predictions and informed decisions for a range of site improvements. The models investigate the influence of SAG mill performance with respect to ore competency, derived from SMC Test® via the measured DWi model parameter. In some cases the benefits of blasting and from fine tuning milling operations are already incorporated into the "site-specific" forecast models. The methodology follows rigorous plant data analysis that is analogous to a "Mine-to-Mill®" optimisation project. The CITIC-SMCC model validation includes extensive data collection, which includes drill core analysis, ore characterisation and comprehensive comminution circuit operational data to assess the limitations within the comminution circuit within the operating mine. The results and models may be used to define the operating base lines of the processing areas and identify improvement opportunities upstream and downstream of the comminution circuit. The predictive capability of the models use logged production data and has enabled the user to differentiate between alternative circuit configuration options and identify optimum operating conditions. This approach minimises the ongoing requirement for costly plant surveys. The improvement strategy for each site, included the ongoing measurement of grindability, rock strength and via the Bond and SMC Test® respectively. Some commentary as to what other practitioners do with input data and their models is also presented as this highlights some of their shortcomings relative to the CITIC-SMCC methods."

Jan 1, 2014

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By Y. Q. Yang

Jig is a kind of conventional and old gravity concentration equipment, which is mainly used in the preconcentration of medium particle fractions of low-grade nonferrous metal ore. In the past ten years, studies on jigs have made a great progress on separation of coarse and fine particle fractions. At the same time, pneumatic jigs have been widely used in processing of nonferrous metal ore. In this paper, pilot test study and commercial operation for several kinds of jigs used in Dachang con-centrator has been introduced. Dachang mining area of GuangXi province is rich in mineral resources, where many minerals exhibit various complex properties. Many elements such as Sn, Pb, Sb, Zn, S, As, Cu, In, Ag, Gd, Ag, Ga, etc, were found in the run-of-mine ore (ROM). At present, Dachang concentrator produces tin concentrate, lead-antimony concentrate and zinc concentrate. Other valuable elements get enriched and recovered in above concentrates. Dachang Mine with a mining operation history more than sixty years will end its mission on the rich ore resource exploitation. At present, low grade ores are porcessed in the concentrator, and the concentrator begins to run at a loss upon processing the low-grade and refractory ore. Heavy medium cyclones were used in the concentrator for processing 20-4mm fraction, Gongge jigs for 4-2mm fraction, and cone concentrator combined with spiral concentrator to discard the tailings of -2mm fractions. In order to minimize overgrinding, table flotation was used to recover some liberated cassiterites in a complex processing technology. Therefore, the concentrator is difficult to manage. Many years studies have shown that heavy medium cyclones and spiral concentra-tors can be replaced by sawtooth shaped wave jigs to discard 50% tailings to improve the grade of feed. And the feed was divided into rich one and poor one to minimize overgrinding of valuable cassiterites with different grinding mills. In this case, the recovery of the valuable minerals can get improved and the flowsheet was simplified. Moreover, the concentrator begins to make profit with reduction of cost. At the same time, pollution in the concentrator gets reduced and the working condition gets improved too. Sawtooth shaped wave jig was used in Changpo concentrator for replacement of cone separators and spiral concentrators to discard the tailings of -4mm fraction, and the yield of discarded tailings got improved from 30% to 50%. Grades of tin, lead and zinc in the tailings are lowered from 0.15%, 0.12%, 0.7% to 0.06%, 0.05%, 0.4% respectively, with a loss reduction of tin, lead and zinc from11%, 9%, 10% to 7.5%, 6%, 5% respectively, corresponding to the increasement of recovery of tin, lead, zinc from 52%, 50%, 55% to 56%, 56%, 62% respectively. Cost of the concentrator for processing one-ton ROM was therefore dropped from RMB155.28 to RMB119.74. Changpo concentrator lost RMB2.5 million in 2003, but it made a profit of RMB0.92 million in 2006 after the innovations. Batac jig was used in Tongkeng concentrator to discard the coarse tailings at 20-4mm, with a discarded yield of 35%, and the grades of valuable minerals got improved with a recovery above 95% for tin, lead-antimony and zinc.

Jan 1, 2014

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By P. S. Dash

With implementation of stringent environmental regulations, ultra clean coal technology development programs have gained significant importance worldwide. As far as Indian scenario is concerned, most of the coals present in India are of drift origin and low grade, containing high mineral matter varying from 15% to greater than 50%. The inorganic or ash constituents of Indian coals are finely disseminated through the organic or carbonaceous constituents so, that commonly used physical beneficiation techniques are of only limited value in affecting separation. Chemical processes involve addition of chemicals, which react with the mineral matter and allow its easy removal. The present study envisages the effect of aqueous alkali leaching followed by acid washing on the removal of mineral matter from two different captive coals of Tata Steel at elevated temperature and pressure. The experiments are conducted at desired conditions using a bench scale pressure reactor set up having proper data acquisition and control system. The research study revealed, that it is possible to reduce the ash content up to 70% by this method. The alkali content of the product clean coal does not increase whereas the silica and alumina content reduces by nearly 58% and 62% respectively. Significant reduction in the phosphorus content is observed after the acid treatment. The crucible swelling number of the feed coal improves after the treatment. The mechanism of demineralisation was evaluated by analyzing the coal samples before and after the alkali and acid treatment using scanning electron microscope (SEM). Because of the acidic nature of the silicates and aluminates, they dissolve into the NaOH solution and form sodalite. Sodalite is partially soluble in the alkali solution. The hydrates formed during alkali treatment are partially removed due to acid wash. This study in overall provides an insight into possible alternative methods of beneficiation for removal of ash from high ash Indian coals.

Sep 1, 2012

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

In the present work, the flotation behaviours of zircon, rutile and ilmenite using sodium oleate as collector in absence and presence of depressants were thoroughly investigated. The maximum in the flotation recovery of any of the above minerals falls within similar pH ranges. A range of inorganic and polymer depressants were examined in order to improve the separation of zircon from rutile and ilmenite. Optimum values of conditioning pH and depressant concentration to achieve maximum recovery and best selective floatability of zircon were obtained. Selective flotation of zircon from Ti-bearing minerals was anticipated from single mineral experiments under different pH values, depressant and collector conditions.

Jan 1, 2014

By Carlos G. Rudolp, Julio C. Videla, Mario Zuleta

"The present paper summarises the results of gravity pneumatic concentration of a borax ore with 17.5 % B2O3. The sample was extracted from the Tincalayu ore deposit located in the Salta Province of Argentina.The applied methodology was based on a former study (Zuleta, 1985). It consisted of sample characterization by means of physical and mineralogical determinations, chemical analyses as well as pneumatic table concentration tests. In this, a simplified concentrating flowsheet was utilized.A concentrate with 30.6 % B2O3 and 74.7 % recovery was obtained. The recovery was 8.8 % less than previously reported and that was of 30.6 % B2O3 with 87 % recovery. Nevertheless, the simplified flow sheet presented processes only two granulometric fractions, - 6.4 mm + 0.3 mm and - 0.3 mm, compared to the three granulometric fractions used in the previous study: - 6.4 mm + 1.4 mm; - 1.4 mm + 0.3 mm and . 0.3 mm. This would simplify industrial implementation."

Jan 1, 2003

By Jacob Masliyah, Zhenghe Xu, Lujie Yan

"Understanding adsorption mechanism of polymeric organic process modifierssuch as carboxymethyl cellulose (CMC) on talc hasbeen a major challenge due to anisotropic nature of talc basal planes and edge surfaces. The main objective of this study is to investigate the adsorption of CMC on the basal planes and edge surfaces of talc.Smooth basal plane and edge surfaces of talc were prepared successfully by simple cleavage and sophisticated ultramicrotome cutting method, respectively. The prepared surfaces were characterized by atomic force microscope (AFM) imaging to be sufficiently smooth for colloidal probe force measurements using AFM. Anisotropic surface charge characteristics were determined,with the basal planes to carry a permanent negative surface charge and edge surfaces featuring a pH-dependent charge characteristic. The adsorption of CMC on talc basal plane and edge surfaces at pH 9 in KClaqueous solutions of various ionic strengths wasinvestigated by in situ AFM imaging technique. Themorphology of adsorbed CMC on talc basal planes and edge surfaces was found to be significantly different, due to different binding mechanisms involved. Interaction of CMC with the talc basal plane was found to bedominated by hydrophobic interactions while its binding with the talc edge surface was mainly through chemical complexation and hydrogen bond. The amount of CMC adsorbed on both talc basal planes and edge surfaces increased with increasing ionic strengthof solutions. The methodology developed in our study opens the door to probe polymer adsorption on anisotropic phyllosilicate surfaces, which can help us better understand the mechanism of polymer adsorption on specific mineral faces."

Jan 1, 2014

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By S. K. Chaudhuri

With a growing emphasis on maximizing the value by rapidly deploying it across their assets, mining firms are eager to identify any issues that may hinder such efforts and to refine their approaches to overcome them. As such a CDE vision can be considered realized when the following components are addressed and functioning as intended - People: the right resources working together and efficiently to achieve shared goals, Process: well-defined workflows mapped out for key value processes, Technology: availability of the correct tools and applications to increase efficiency in work execution and Locations: regional locations/ sites that need to be linked for collaboration and information exchange. For the above vision, an approach that considers the degree of interaction between the roles in metallurgy operations, mineral resource planning, mine engineering, plant operations, logistics and infrastructure, and which accounts for the current technology states across these groups to determine sub-processes where the impact of a CDE will be the most is critical. In effect, CDE is more about transforming an organization?s operational philosophy than a technology driven project. This paper examines the definition and components of a CDE in a mining context. Real-time operations co-ordination, maintenance interventions, production analysis and optimization processes are examined along with current state technologies and manual processes as candidates which are likely to result in most benefits from collaborative work processes. Finally, the paper examines technologies that can be used to further enable a collaborative working environment.

Sep 1, 2012

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure, for use in the prediction of flotation circuit performance, far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, data collected from an industrial flotation circuit is used to derive the parameters associated with two different types of flotation models. Simulations performed using these models demonstrate the need to differentiate between cell and feed properties. A model that does not differentiate between these two properties fails to successfully predict the metallurgical performance of a flotation circuit after a disturbance."

Jan 1, 2003

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using Sodium Dodecylsulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).By comparing the coprecipitant type and concentration studies it could be concluded that As5+ removal in the presence of Fe3+ (160 mg.L-1) alone, or a Fe3+ (80 mg.L-1) and Al3+ (40 mg.L-1) mixture, is equivalently effective (99,9%) and greater than in the presence of Al3+ (80 mg.L-1) alone (97,7%).Through SEM/EDS analyses, it was possible to observe that both morphology and composition of the precipitate produced in the solution and retained in the foam depend on the physico-chemical conditions of the system, that is, on the species present in the solution."

Jan 1, 2003

By I Brum

Brazil and Colombia have large reserves of coal, those reserves in Brazil are located predominantly in the south and Colombia the main reserves are located in the north. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently, these countries are developing projects and partnerships aiming to qualify this mineral resource, adding quality to the final product of the processing plants. In this scenario the processing of Brazilian and Colombian coal in flotation columns appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of column flotation for a specific Brazilian coal and a specific Colombian coal. The material used in this study consists of fine coal from Brazil (Copelmi) and Colombia (Cerrejon). The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The two coals were floated using a negative bias in a 5 cm diameter conventional flotation column of 5 m high. Flotation parameter investigated included air velocity in the range 0.6 to 1.5 cm/s. For all runs, a constant negative bias of -0.25 cm/s and a pulp concentration of 8% w/w were used. For Cerrejón coal, 300 g/ton of frother and 907 g/ton of collector was used, whereas for Copelmi coal, 600 g/ton of frother and 1815 g/ton of collector was employed. The frother was a commercial Aerofroth 65 (AF65), whereas the collector was Kerosene. For the Colombian coal, in general, yield, organic recovery, ash recovery and water recovery decreased with the increasing air rate. However, for Brazilian coal the air rate had no significant effect. For Colombian coal, the highest yield (60% w/w) and organic recovery (69% w/w) were obtained at the lowest air rate (0,6 cm/s). Keywords: negative bias, column flotation, coal

Sep 1, 2012

By Xiaojing Li, Yueyuan Zhou, Shengyao Ma

The paper presented the acnalysis of field intensity of rare-earth permanent magnet with high BH product and the research of magnet configuration with narrow pole pitch on open magnet surface, both using ANSYS. The possibility to separate micro-disseminated feebly magnetic minerals by improving the field intensity and the capture line distribution rate on open magnet surface were verified. The research on the method to pile up magnets to increase peak value of field intensity on the open magnet to 1.0T was done through correlation analysis between shape and dimensions of magnetic material and field intensity. And the research on technology method to improve capture line distribution rate in the separating field to 1.25×105/m2 was done through optimization design of magnet configuration of the open magnet with narrow pole pitch. Laboratory tests were performed with hematite sample from ore dressing plant such as Hainan mine, Qidong iron ore, etc. The separation results acquired were at the same level as using the electromagnetic separator, verifying the possibility to separate micro-disseminated feebly magnetic minerals with open magnet. The research suggested a new idea about the development of magnetic separator with high efficiency and low costs to separate feebly magnetic minerals and non-magnetic gangues.

Jan 1, 2014

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By V. V. Trusova, Shiyrav Gandandorzh, K. V. Fedotov, V. A. Domracheva

"In Russia, 1.1 million tons of mercury-containing waste are stored. The amount of mercury in soils and heaps of industrial enterprises is estimated at 3000 tons; in dumps, concentration tailings, sludge dumps of the gold mining industry up to 6000 tons have been accumulated. Mining is one of the main sources of mercury emissions in the natural environment that poses a real threat to the natural environment. At present, the process of amalgamation is prohibited and not applied in gold extraction. The application of amalgam technology in gold mining led to the accumulation of highly toxic products in the form of gold-bearing amalgam and metallic mercury, with a mercury content of dozens and even hundreds of times greater than the maximum permissible concentration for soil (1). Therefore, mercury-containing tailings constitute an ecological hazard to the environment. According to published data, at waste storage sites of industrial enterprises, up to 50 tons of mercury enter soil annually, and up to 3.5 tons pollute the air. At the same time, mercury-containing waste due to the reduction of the country's mineral resources is an additional source of mercury. Therefore, it is necessary to recycle mercury-containing waste. INTRODUCTION Paperobjective: demercurization of technogenic raw materials (amalgamation tails, discharge outlets of tailing dumps) to be recycled. Under natural conditions, the mercury usually migrates in the form of three most common compounds: elementary mercury (Hg); mercuric mercury ion (Hg+2); methylmercuryion (Hg (CH3) +. Chemical compounds Hg (II) are found in natural conditions much more often than Hg (I).The authors propose to conduct demercurization of technogenic raw materials (mercurial tailings) in two stages. At the first stage, the mercury in the form of small balls, the finest particles (drip mercury) can be extracted by applying the gravitational method. We propose a method for centrifugal processing of crushed waste in the apparatus of Itomak company, Novosibirsk, as the basis of the technological process for mercury recycling. The extraction of metallic mercury out of mercury-containing waste into commercial products, according to the technological characteristics of the Itomak apparatus, reaches 86.0% (2, 3). At the second stage, the extraction of mercury out of technogenic raw materials is performed applying a sorption method and using carbon sorbents based on fossil coals. Hard coal of the Kuznetsk Basin has been already used for industrial production of active carbons (carbon sorbents) of the KAD-iodine type, which is one of the prerequisites that determine the choice to use it for the aims of this study."

Jan 1, 2018