Search Documents

By A. Mainza, H. Hill, L. S. Bbosa

"Impact breakage is the most elementary size reduction mechanism in comminution devices. In comminution research, characterization of breakage is primarily concerned with the energy expended to cause it. The main challenges of this approach have been quantifying the actual energy requirements of impact breakage and developing mechanistic models to accurately describe the process. For engineering load analysis, fracture is characterized in terms of strengths such as yield stress and ultimate tensile stress, which govern the maximum loads specific materials can be subjected to before irreversible inelastic deformation and subsequently complete fracture occur. With this approach, the main challenge has been to elucidate the underlying mechanism, in the means that the load causes weaknesses in the material microstructure to act as sites for stress concentrations, leading to crack initiation, propagation and eventual failure. Studies dedicated to investigating particle fracture under impact loading have led to the development of several devices for conducting breakage characterization tests. These devices include the drop weight tester, split Hopkinson pressure bar, rotary breakage tester and the short impact load cell. All these have different particle loading and breakage methods, and thus can yield distinct information which can be compiled together to study a material and the nature of breakage. This work analyses the single impact breakage data obtained across the listed devices. A homogenous ore commonly known as blue stone is used for all breakage tests. The work is conducted using standard procedures specific to each device as closely as possible. Drop weight and rotary breakage tests were used to obtain hardness parameters based on an existing t10 breakage model, while split Hopkinson pressure bar and short impact load cell measurements provided properties based on conventional engineering load analysis. The results were used to highlight the significance of the loading geometry, impact mechanism and impulse on the extent of breakage."

Jan 1, 2018

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:- flotation tailings of crystalline graphite minerals- outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers.The most important variables affecting the leaching process, such as grain size, mineralogical species, reagent consumption, and so on, were previously studied. (Weiss, L.1985)On the basis of the present study results, the possible definition of an economically viable mineralization will be analyzed to define an auriferous district."

Jan 1, 2003

By J. J. Lui

Surfactant plays a critical role in many industrial processes such as petroleum, mining, environment and food processing, and daily life. For ionic surfactant systems, adsorption of surfactant at oil-water interface imposes a net charge to the interface. The nature and magnitude of the charges at the oil-water interface depend on charge characteristics of surfactant molecules, concentration of surfactant and solution pH. In our previous study, zeta potential measurement of hexadecane drop-lets in industrial process water was shown to be a simple, yet powerful method for identifying various types of ionic surfactants present in the aqueous system. In this paper, the site-binding model was applied to prediction of zeta potential of oil droplets in aqueous solutions containing a mixture of cationic and anionic surfactant molecules. The total number of interfacial sites for various types of surfactant involved was determined by applying the Gibbs adsorption equation to the measured interfacial tension-surfactant concentration profiles. The distribution of various types of surfactant molecules at the interfaces was evaluated by Langmuir isotherm constants. With the ionization constant of surfactant taken from the literature, the predicted zeta potentials of oil droplets in surfactant solutions from site binding model were shown in a reasonable agreement with the measured zeta potential values.

Jan 1, 2014

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By Sydney Mantsho, Toni Streczynski, Manuel Gonzalez

"In 2013, the commissioning of the MillStar Stabilisation and FloatStar Stabilisation and Optimisation controllers were completed at the Cerro Bayo Silver (Ag) mine in Patagonia, Chile. The MillStar control system has stabilised the feed to the SAG mill as well as the density at the discharge end of the SAG mill and ball mill. The FloatStar Stabilisation and Optimisation controllers have successfully stabilised and optimised the flotation circuit to ensure consistent product quality within desired specifications.The mill feed is controlled utilising the MillStar Solids Feed controller. Additionally, the solids to liquid ratio into the SAG mill was controlled utilising the Mill Inlet Ratio controller in conjunction with the Solids Feed controller. The discharge end of the milling process is a highly interactive and complex system. The use of a Robust Nonlinear Model Predicative Controller (RNMPC) was ideally suited to control this section of the process. On the Cerro Bayo milling circuit, the RNMPC was used to control the mill discharge sump level and the primary cyclone feed density to produce a more consistent feed to the flotation circuit.Three levels of the FloatStar control system were installed, for flotation stability, concentrate flow stability as well as grade optimisation. The Level Stabiliser was used to stabilise the level control on 6 flotation banks. The Flow Optimiser was commissioned on the Rougher, Scavenger and Cleaner concentrate sumps to stabilise concentrate flow from the flotation cells. The Grade Recovery Optimiser was commissioned on the Roughers section. A number of instrumentation challenges were identified which limited the overall benefit derived from the system. Once these were addressed, the performance was optimised. The overall benefit provided by the system was observed in terms of the improvements in Ag recovery."

Jan 1, 2014

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By N. Nehoroshev, P. Solozhenkin, N. Voyloshnikova, A. Pshennikov

"Molecular modeling of clusters of major bismuth minerals, Bi2S3, was carried out whereby molecular models of minerals and reagents clusters were created. Their HOMO and LUMO energy levels were calculated and using known modelling equations, the absolute hardness ?, eV and electronegativity were calculated. The charges of separate atoms of clusters and the change of properties of the minerals were determined which allowed predictions of the flotation properties of raw ores containing rare bismuth minerals. Modeled complexes containing the clusters of minerals and various collectors were constructed, consisting of atoms and bonds within clusters of minerals. Major physical and chemical parameters were determined for the complexes created, including the total and electronic energy. Based on the energy calculations, predictions of the collector efficiency were proposed. The efficiency of collector was established for various thiolic reagents, the compounds of phosphorus (III) and mixtures of reagents. Theoretical results were checked and confirmed against laboratory ore flotation tests. A gold-bismuth-magnetite ore type was studied where gold, bismuth and iron (magnetite) are of industrial interest. The ore contains 2.8 g/t Au, 1.0 g/t Ag, 0.26% Bi, 45% Fe and 1.25% As. Sulphide mineralization can be mainly found in the form of pyrrhotite, pyrite and arsenopyrite. Bismuth can be mainly found in the form of bismuthite and native bismuth. Gold is fine. A flow sheet for Zhelezny Kryazh ore treatment was proposed. This flow sheet consists of grinding to 95-98% -74 µm, sulfide flotation with two cleaner with xanthate addition, cyanidation of flotation concentrate and flotation tailings included treatment with with CaO (6 kg, 6 hours), cyanidation (8 hours) and CIL (8+24 hours). Saleable products are gold doré, bismuth and iron concentrate."

Jan 1, 2014

By Ivan Bonchev, Elisaveta Djurova, Evgeni Visariev, Viktor Stoilov

"Two types of slag cooling is used world wide - cooling in ladles and cooling in pits. The flotation comparison of the type cooling regimes was done at Aurubis Bulgaria. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag flotation plant processes blend of three parts FSF and one part converter slag. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper content in flotation concentrate is over 20 % and in flotation tail is under 0.5 %. In order to improve the copper recovery, different cooling rate of the liquid slags should be achieved. Three cooling experiments with flash smelting furnace (FSF) slag have been done: two of them in pits with different volume and one cooling experiment in metallic ladle. The ambient air temperature during the cooling tests was from -4 to +4 OC. Laboratory flotation tests in open cycle were done with an aim to compare the slags behaviors cooled at different conditions. In this paper the effect of different cooling on the flotation process will be presented. The copper recovery and distribution by sizes in the tails, copper content in the rougher concentrate, and the concentrate yield are discussed."

Jan 1, 2014

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By Mohammad Kor, David Beattie, Agnieszka Mierczynksa-Vasilev

The selectivity of polymer adsorption in mixed mineral systems is the basis for polymer depression of gangue minerals in flotation. Effective polymer depressants not only reduce gangue mineral recovery, they also have minimal effect on the recovery of the value phase, presumably through targeted adsorption on the gangue phase, and minimal uptake on the value phase. Traditionally, polymer depressant design has been guided by single mineral phase adsorption tests, with affinity and maximum adsorbed amount determined for gangue and value phases separately. However, there is a need to determine the actual extent of adsorption on the gangue phase while in the presence of the value phase. In this work, we report on the development of in situ atomic force microscopy (AFM) imaging for determination of polymer depressant coverage and morphology on mixed mineral surfaces. Our group has previously used AFM imaging on single minerals to connect adsorbed layer characteristics with bubble-particle attachment and flotation outcomes. Two sample types were used to test the methodology: (i) a mixture of two crushed/ground minerals encased in resin; and (ii) a composite mineral sample containing macroscopic regions of three different mineral phases. The samples have been used to probe the selective uptake of two modified dextrin polymers (octenyl succinate anhydride dextrin). AFM images acquired in situ (while all surfaces are immersed in the same polymer solution) of each mineral phase have revealed the natural selectivity of the polymer for the mineral surfaces. In all cases, the polymers adsorb on the all mineral surfaces present, but to a varying extent.

Jan 1, 2014

By J. K. Afidenyo

Microbial pretreatment of a double refractory gold ore was investigated using a white rot fungus, Coriolus versicolor (ATTC 20869) to improve gold extraction. A series of preliminary tests were conducted to determine the amenability of the ore to fungus degradation. Pulp density, temperature, pH and retention times were the process variables considered. Both a single. Stage and two-step processes were studied to establish process conditions. During the single stage process, the ore was contacted with the fungus culture (biotic) for 3weeks at 30°C and pH 10.0. For the two-step process, the first step involves ore contact with the culture medium (abiotic) at 45°C and pH 10.0 followed by fungal contact (biotic) at 30°C. Results indicated that carbonaceous matter is not degraded but passivated by the fungus; as preg-robbing activities dropped significantly from 18.1% to below 1.0%. The single stage process resulted in higher gold recovery than the two-step process Gold ex-traction by cyanidation of the pretreated ore was 78.9% for the single stage compared with 15.0% for the untreated ore. In the two-step process, only 73.3% gold extraction was achieved. Application of the two step process conditions to a high grade flotation concentrate, resulted in 93.3% gold ex-traction as against untreated concentrate of 30.5%. The results show that the microbial pretreatment process degraded sulfide sulfur, passivated carbonaceous matter and enhanced gold extraction from double refractory gold ore and concentrate.

Jan 1, 2014

By A. J. Lynch, D. K. Tungpalan, Y. Reja, E. C. Avelar, G. Figueroa, S. Gómez, R. Alanis, M. A. Corona-Arroyo

"Have you been on a mine site? This question was posed by Emeritus Professor Alban Lynch to Higher Degree by Research (HDR) Students from the Sustainable Minerals Institute - Julius Kruttschnitt Mineral Research Centre (SMI-JKMRC) in the Student Technical Presentations in 2015. From that question, five HDR students from SMI-JKMRC organised a placement on mine sites in Mexico. The SMI-JKMRC is well known for its tradition to provide their students with opportunities to enhance and test their skills in mineral processing plants. The Student Venture became a short internship for HDR students which had the objective of establishing collaboration with mining companies in Australia and overseas, and of providing a unique experience for the HDR students in regard to their training, professional development, networking and cultural interchange. In return for the companies’ support, the students conducted plant audits to evaluate the process performance thereby providing valuable data to the host company. The 2016 Student Venture was held at the Grupo Peñoles & Grupo Fresnillo in Mexico, in which three mine sites received five HDR students from JKMRC and one young researcher from Universidad de Guanajuato (UG). This paper describes the positive outcomes for the mining company and the students for this experience. The Venture was considered very successful, as it provided valuable training for the students as well as in depth information about the operation of the comminution and flotation circuits of the host sites for the Grupo Peñoles & Grupo Fresnillo. The experience also provided an opportunity for an exchange of knowledge between the HDR students and the site personnel from the host operations. The indication of the success of the experience for all involved was the support of the host company in future student internships."

Jan 1, 2018

By Markus A. Reuter, Yongxiang Yang, James R. Post

The packed coke bed in the lower part of an iron making blast furnace, the dead man, dissolves slowly in a pool of hot metal, which is tapped regularly. The coke particles of the dead man not only exhibit a size distribution, but also their size distribution is non-uniform throughout the dead man and as a result, the porosity of the dead man is non-uniform. This causes the flow of hot metal through the dead man to be irregular and non-uniform, bringing about channelling in the coke bed. Channelling is detrimental to the refractory lining life of the hearth of a blast furnace. Using population balance modelling and a porosity model it is possible to keep track of the local changes in size distribution and bed porosity during dissolution of coke particles. Numerical simulations show that carbon dissolution from a packed coke bed (with particles which exhibit a size distribution) increases the average porosity, decreases the mean particle size and changes the size distribution to a distribution with a smaller size range. Influence of the type of initial size distribution (mean, variance) is investigated. The calculated changes in porosity are used to dynamically adapt the flow and the mass transfer (kinetics) during calculations. This approach provides the possibility to implement dynamic porosity calculations for CFD applications, and thus simulate the results of various coke types and particle size distributions on dissolution and flow behaviour.

Jan 1, 2003

By G. Demi

The biggest chromium mineral processing plant in Albania is Bulqiza plant. It has been in operation for more than 20 years, treating low-grade chromium ores grade 20 ? 26 % Cr2O3 and producing chromium concentrates grade 48 ? 50 % Cr2O3. About 2 million tons of tailings with 13 % Cr2O3 content are stocked in a dam close to the plant. Mineral processing of low-grade chromium ores with less than 16% Cr2O3 content is unprofitable because the mining expenses are high comparing with the current market prices of chromium concentrate. Recycle and enrichment of existing tailings is profitable, because there are no underground mining expenses in this case and because that this kind of raw material does not need expenses operation of crushing and grinding. The existing plant is in operation for more than 8 years treating existing tailings as raw material. Grade of concentrate in the value 40 % Cr2O3 and Cr2O3 recovery in the value 30-35% in the plant are considered low. The main reason of low concentrate grade and recovery is high content of particles under 100 microns, the slimes, in raw material. In the paper is described the study carried out to improve enrichment of the tailings, as well as analyses of existing process, raw material and products. It is concluded that majority of lost is present in the slimes which are not separated in existing spiral separators and shaking tables. Basing in the study is composed the new flow sheet of recycling and concentration of the tailings to produce chromium concentrate grade 41 ? 42 % Cr2O3 and recovery 60 %, decreasing in this way the concentrate production cost two times. In the paper are presented the tests and results of concentration of particle size fraction under 100 microns, using gravimetric, magnetic and flotation methods, as well as equipment and machines suitable for slimes treatment and concentration.

Sep 1, 2012

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By T. Fujita

The incinerated bottom ash includes titanium oxides and a small amount of chromium oxides. Initially, 89 % of chromium was removed from ash at magnetic flux density at several stages of wet magnetic separation from 0.05 T to 6 T. The bottom ash from an industrial waste incineration process includes about 10 % of TiO2. The minerals that contain titanium are rutile and perovskite. These minerals are paramagnetic and show low magnetic susceptibility, therefore, the high magnetic field strength, created by a superconducting magnet, is necessary to capture these minerals. At the first stage of separation, a magnetic field strength of 6T was applied in order to attract the particles that contain iron oxides to the higher magnetic field region. At the second stage of separation, the magnetic capture rate of weekly magnetic particles decreased with increasing the magnetic susceptibility of the aqueous solution (i.e. the medium for dispersing the particles) in order to separate the highly magnetic materials. The para-magnetic salt such as ferric chloride was dissolved in the water to increase the magnetic susceptibility of the medium. After a two-step wet HGMS with superconducting magnet, the grade of TiO2was increased from 10 % to 28 % with a recovery of 64 %.

Jan 1, 2014

By A. Javadi

"Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Bama concentrator in Iran but with the addition i) Na2S reductant and ii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid.INTRODUCTIONOur recent studies have illustrated the formation of hydrogen peroxide (H2O2) by metal-sulphides during grinding in the presence and absence of oxygen (Javadi Nooshabadi & Hanumantha Rao, 2013a; Javadi Nooshabadi & Hanumantha Rao, 2013b; Javadi Nooshabadi & Hanumantha Rao, 2013c; Javadi Nooshabadi & Hanumantha Rao, 2014). In the absence of oxygen, it was found that pyrite surface is catalytically active and able to breakdown water molecules to form OH• free radical and thereby deriving oxygen in the formation of H2O2 from water molecules. The in-situ formation of H2O2 and its influence on sulphide flotation has not been addressed yet. The presence of strong H2O2 oxidant in the pulp liquid and its selective oxidation of pyrite would be beneficial in depressing pyrite flotation. Therefore, it is important to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp as well as to study possible ways of flexibly controlling the formation of these species through known chemical means for depressing the generation of the oxidant."

Jan 1, 2018

By M. Eraydin

Dewatering fine particles (e.g., flotation concentrates) is inefficient, energy intensive and often requires large capital and operating costs. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids and a hyperbaric centrifuge. Typically, the moistures obtained using these methods are 30% to 50% lower than those obtained using conventional methods, as demonstrated in laboratory and pilot-scale test programs. With another novel dewatering technology that has been tested in bench-scale tests, the moistures can be reduced to levels once believed to be attainable only through the use of thermal dryers. In this communication, test results obtained with these advanced dewatering technologies are presented and compared.

Jan 1, 2014