Search Documents

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By D. A. Ponniah

The installation of a pile is considered analogous to the expansion of a cylindrical cavity of a diameter equal to that of the pile. Using Vesic's theory of the expansion of cavities the effect of soil properties on pile installation loads, radial pore and total pressures are evaluated. The theoretical results are compared with load and pressure measurements made in field trials in a stiff clayey glacial till in the U.K.

Jan 1, 1987

By T. Matsui

Many existing bridge abutments on the soft ground laterally move and their many damage examples have been reported. An essential cause for the troubles of the lateral movements may be the lack of examinations for the lateral earth pressure acting on its foundation piles. In the present paper, actual movement condition of existing bridge abutments is first summarized, and then the author establishes a practical and systematical design method for bridge abutment foundation piles, including the examination for the passive pile.

Jan 1, 2010

By H. Mori

Construction of cast-in-place piles with enlarged bases has become popular in the cities in Japan facing to the sea coast, where the subground soil is soft alluvium deposited to depths often exceeding 30 m. The groundwater table is a few meters below the ground surface. Skin friction of piles may become negative due to ground subsidence or reduced due to liquefaction of loose sand during an earthquake. To support highrise buildings, depths of bearing strata to which piles are embedded often exceed 50 m. Due to such geotechnical conditions, methods and equipment to build cast-in-place concrete piles mainly built by the reverse circulation method have been developed since the 1970s. In the first half of this paper, the authors review the cur-rent practise of building cast-in-place piles with enlarged bases. Then they introduce the TFP system developed in recent years, and discuss about the procedures to control and monitor enlarging of bases.

Jan 1, 1989

By Armin W. Stuedlein, Seth C. Reddy

In this study, factors affecting the reliability of augered cast-in-place (ACIP) piles under axial compression at the serviceability limit state are addressed using a simple probabilistic hyperbolic model and a database of load tests on ACIP piles in cohesion less soils. The aleatory and model uncertainty in a selected load-displacement model is statistically characterized, and is used to simulate representative random samples from the bivariate random vector of model parameters. A first-order reliability method (FORM) was used to determine the effect of sample size on the stability and uncertainty of the reliability index. Sample sizes greater than about 40 provided relatively consistent estimates of the reliability index; however, its uncertainty continued to decrease with increasing sample sizes. Additionally, the effect of slenderness ratio on the reliability of the serviceability limit state design was characterized and found to exhibit a significant effect on the probability of exceeding a specified displacement.

Jan 1, 2013

By Cen Guoji

The foundation of bored pouring concrete pile have been adopted in the bridge engineering of China since early in the sixties. They demonstrated tremendous technical advantage and achieved notable economic benefit. With improvement of bridge technique including construction technique work equipment, design theory, examination in quality and applicable range etc, the pile diameter became bigger and the foundation changed from shallow to deep-water. This paper examples Jiujiang Bridge of Guangdong in China, which is single-tower cable-staged bridge, total length of 1675m, and expouds adopted successfully the foundation of variable section large bored pile (upper part d=3m, central part d=2. 4m and lower part d=2m) on the conditions of complicated technique that the load is tremendous (it require specially to resist 12000 kN ship impact) and the piles have free length 30m. The paper will be to describle design project and construction practice of pile foundation with variable section, and to compare schemes of equal section pile and pile in sinking-well.

Jan 1, 1991

By Nathan Iverson, Allie Brady

Located on rolling bluffs on the Zumbro River's south fork in Southeast Minnesota, Rochester is the state's third largest city and is the home and birthplace of the renowned Mayo Clinic, a nonprofit academic medical center focused on integrated health care, education and research. Mayo Clinic employs more than 4,500 physicians and scientists with another 58,000 administrative and allied health staff across three major campuses: Rochester, Minnesota; Jacksonville, Florida; and Phoenix/Scottsdale, Arizona. Originally developed as a stagecoach stop, Rochester has become a national destination for medical care, drawing more than two million visitors annually to Mayo's Minnesota location. Since January 2022, Veit & Company has been working on the construction of the Mayo 1st Ave Tunnel, which comprises three tunnels (pedestrian, utility and services), and the RMC Loading Dock projects in Rochester. These adjacent projects are on the Mayo Clinic's ever-expanding campus and represent its continued dedication to improvement and advancement as a leading medical service provider in the industry.

Jan 1, 2023

By Willie M. NeSmith

The use of drilled (screwed) displacement piles is an emerging sector of the United States deep foundation industry. During installation of these systems, a Ko to Kp environment is created in the materials surrounding the pile immediately prior to casting, and this condition results in increased shaft and toe resistance in soils where displacement leads to densification. Current continuous flight auger and drilled shaft design methodologies in the United States assume a Ko to Ka condition in the vicinity of the pile, and are thus an inappropriate starting point for static capacity analysis of drilled displacement piles. This paper examines constructability issues, and the sensitivity of performance to installation, and offers an empirical design methodology for drilled displacement piles. The proposed design process has been based on evaluation of 40 load tests, primarily in granular materials, and in a variety of geologic settings, and includes modification for soil types within the coarse-grained range.

Jan 1, 2002

By Alan G. MacKinnon

The current piling practices in the U. S. have, to a great degree, been influenced by our founding fathers. When our constitution was written by the delegates from the original thirteen colonies, it was a document of compromise. Generally, the individual states retained their sovereign power over those duties that they had historically performed. The concept of States Rights has been tested throughout our history and has been preserved as of today. An example of the extent of this protection is occurring in the State of Ohio where I currently live. Each of the 50 states receives funds for highway construction from the federal government, approximately in proportion to its population. Congress, when it allocates the funds, quite often attaches amendments to the funding bill to exercise their authority. The major amendment prior to the most recent increase in the speed limit to 65 mph from 55 mph was to increase the legal drinking age to 21 from 18 years old. Embodied within the bill was the provision that the Federal government deduct a percentage from the allocation of any state that did not revise its legal drinking age law from 18 to 21. In the State of Ohio, this change in the law was put to a vote of the people and it was defeated. The federal government now is deducting funds

Jan 1, 1987

By J. L. Liu

Long-term maintained load test on the bored pile group in unsaturated silty soil has been carried out. And the research on the time effects of bearing behavior of pile group has been done by the method of installing pressure cells and reinforcement stress gauges for measuring the soil reaction beneath the cap and the pile bottom as well as the shaft resistance. The test shows that, within a certain duration after loading, the soil reaction beneath the cap and the pile point resistance increase with time; but the shaft resistance decreases. The load distribution among the pile tops in the group tends to be even with time. The shaft resistance redistributes along the pile shaft with time, that is, getting less in the upper part, getting larger in the middle. The redistribution does not tend to stop till the distribution in both upper and middle part becomes to be uniform. The load-bearing conditions of soil beneath the cap of pile group and the variation in time effects with related factors also have been discussed.

Jan 1, 2010

By William F. Loftus

When high capacity diameter pipe piles are driven open-ended into the underlying bedrock, the material gathered inside the pipe often must be excavated to allow concrete to be placed within, in a clean environment. This paper discusses a method of dealing with this ?to be excavated material - the contaminated soil of the Harlem River in New York City, USA.?

Jan 1, 1996

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By Emad Farouz, Ehab S. Shatnawi, Charles Winter

The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilled-shaft diameters has motivated the development and increased use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft axial capacity, especially for shafts tipped into loose cohesionless soils. To date, there are a couple of documented design methods for estimating the axial geotechnical resistance of base-grouted shafts. However, there is no or lack of research that addresses the lateral response of such shafts. A base-grouted drilled shaft test program was carried out during the design phase of the Wisconsin I-94 Zoo Interchange reconstruction project. The test program included installing and testing one base-grouted shaft and one ungrouted shaft under both lateral and axial loading. Based on test results, it was concluded that the lateral behavior of the BG drilled shaft is significantly stiffer than conventional drilled shaft . Hypothetical method was developed to account for potential increased, however, the method should be verified with more lateral load test.

By Robert Small, Amshu Chappa, Ihab Allam

The Biosolids Digester Facilities Project (BDFP) is located in southeast San Francisco. The jobsite is bounded by active Caltrain and Union Pacific Railroad tracks on the west side and the existing Southeast Treatment Plant (SEP) on the north, south and east sides. The existing SEP was constructed in the 1950s and portions of the facility have reached their operational life. The $2 billion BDFP will replace and relocate the outdated existing solids treatment facilities with more reliable, efficient and modern technologies and facilities. In addition, the nearby Bayview and Hunters Point neighborhoods will benefit from the improved odor control. MWH/Webcor, a joint venture, as the construction manager general con- tractor (CMGC) for the project. As part of an alternate delivery method set forth in the prime contract, the CMGC was permitted to propose the use of a core trade subcontractor partner for the SFPUC's approval to provide precon- struction services. The CMGC identified three major scopes (electrical, mechanical and foundation) where a core trade partner would be able to assist

Jan 1, 2023

By R. L. Wei

The disturbing influences of pile driving on the surrounding soil mass, including the induced vibration, pore pressure and displacement of soil, were observed during the construction of pile foundations. It is shown that the effects of pile driving in saturated soft clay are tremendous and ought to be concerned attentively.

Jan 1, 2010

By X. Y. Hou

The design practice of several circular underground projects with large diameter is summarized. By taking the advantages of load-bearing of circular structure, a rational annular tensile bar support system and a new design method are proposed. Calculation for a car park shows that remarkable results are brought in by this design technique.

Jan 1, 2010

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By C. N. Baker

The design and construction of drilled piers through water bearing and caving soil conditions are discussed. The need for close cooperation between the design engineer and contractor in both the design and construction stage is outlined. Four case histories illustrating the design and construction considerations for four different problem soil and ground water profiles are presented, including the field testing and observation procedures that were utilized to confirm that the design inten. was accomplished. Requirements advisable when placing concrete under water in a cased environment and when placing concrete under slurry in an uncased environment are described.

Jan 1, 2010

By Kirty Dave

Foundations in any contract are the most uncertain parts of the contract and most of the "Construction-Contract-Disputes" are either directly related to foundations or arise as 'Side-effects of changes in promises related to foundations. Foundation Engineering is defined as ' The art of selection, designing and constructing the elements that transfer the weight of structure to the underlying Soil or Rock." (Ralph B. Perk). This art started becoming a science since 1920, when scientific efforts to determine the behaviour of sub-surface materials were made. The art and science merged to give new techniques and the science started dominating the field as more and more refinement came in techniques to predict more accurately the characteristics of the sub-surface elements. Inspite of good thorough investigations and design, the contractual promises drafted could leave some room for differences between the parties and above all the prudency expected of both the parties may fall short of the expectations raised in the contract. This may give rise to disputes which may need to be resolved as per principles of law. This paper attempts to initiate a dialogue amongst Foundations-Engineers and Contractors as to how do we minimise the differences arising out of or related to contracts concerning "Foundations".

Jan 1, 1996

By Kashyap Chaturvedula, Emad Farouz

The paper presents a discussion on the axial capacity of deep foundation elements bearing in the Yorktown formation in the southeastern region of Virginia. The fossiliferous marine soils of Tertiary age Yorktown formation typically consist of silty/clayey Sand or sandy Silt/Clay with varying amounts of shell fragments. The Yorktown formation is generally divided into Upper and Lower Yorktown layers depending on the shell content and the percent fines. Results of multiple load tests performed by Jacobs Engineering on auger cast piles as part of water and wastewater treatment plant expansion projects in southeastern region of Virginia are presented in this paper. The paper describes the subsurface investigation methods used to study the existing subsurface conditions and the design methodologies followed to estimate the axial capacity of the auger cast piles. The paper provides details regarding installation of test piles, instrumentation, load testing procedure, and interpretation of test results. The paper presents a comparison between the various methods of estimating axial capacity of auger cast piles based on the SPT-N values, the empirical methods for the Yorktown formation and the load test information. The paper distinguishes the side resistance values obtained within the upper and lower Yorktown formations. The paper compares the various design methods to the multiple load test results and recommends a design modification that is closer to the load test results.