Search Documents

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008

By Wang Lushuang

This thesis is devoted to the research of the interaction between pile and foundation soil by boundary element method (BEM for short). The interaction is simulated by the interaction between two different elastic mediums. The foundation soil is simulated by the two-dimensional elastic half-plane, and the pile by the two-dimensional elastic finite plane. Therefore, the calculating models made by the paper's author would come more closed to the actual conditions. The elastic behaviour of the interaction between pile and soil, and the whole course of pile ultimate load are analysed in the thesis, and the relevant applied computer programs "BEME", "BEMPA" are designed by the paper's author. The bearing power of single pile can be worked out by the program "BEMPA", it has compared with staic loading tests of pile, and the results are in conformity to actual conditions. So it can be drawn that the BEM for studying on interaction between pile and foundation soil made in the thesis is more simple, more precise and more practical in actual project.

Jan 1, 1991

By Mai Yuanjian

The stabilization effect in large excavation slope with vacuum wellpoints system during construction of a dry dock located in Guangzhou is introduced in this paper. In-situ observations indicate that the effect of wellpoints for decreasing seepage in slope is remarkable even though the muddy sitty clay in it has poor permeability and the slope can remain its stability well. Meanwhile, a non-linear partial defferential equation has been set up to the whole unsteady seepage process as water level in the foundation pit excavated under water goes down to the bottom and so does the seepage in slope due to dewater by vacuum wellpoints system at the same time. And the finite-defference method has been used to solve the equation mentioned above, which differes from conventional wqy where the equation will be linearized firstly. Since the water heads in slope with wellpoints dewatering are more variable, it is necessary to keep non-linear. The calculation results are in good accordance with observation. Vacuum wellpoinnts for slope stabilization in this work is successful.

Jan 1, 1991

By Kimberly Martin

The EFFC/DFI Carbon Calculator provides the deep foundations industry the opportunity to be a leader when it comes to carbon reduction. This tool was created 10 years ago in an extensive effort by the European Federation of Foundation Contractors (EFFC), DFI, member organizations and Carbone 4, a consultant with ex- perience in life cycle assessment. The tool was born out of the fact that governments and clients were asking for embodied carbon information for foundation systems, and that in- dividual companies were building their own calculators to meet these requests. To help all member organ- izations achieve compliance, and to have a sector-specific tool that is certified to the prevailing standards, EFFC and DFI agreed to partner to create the carbon calculator, which is: Excel based and, therefore, easy to learn and use Updated on a regular schedule Certified to ISO 14067, GHG Protocol and PAS 2050 Free and available for anyone to use Even though this tool is free and easy to use, most projects in the industry do not have a carbon calculation performed. The case to use the calculator is more obvious for members in places like Europe where there are stricter reporting standards and government work can be driven by sustainability over cost. In North America this is not the case, yet. Without directives from clients and governments, what can compel the industry to start regularly using this tool and care about the carbon emissions of projects during design and construction?

Nov 1, 2022

By William Siegel

Kleinfelder provided foundation analysis and design for an expansion to a cement plant in Florence, Colorado. The expansion was a conversion from a horizontal wet process to a vertical dry process, and resulted in the construction of a number of structures with heavy foundation loads. [ ] The field investigation identified old fill and saturated sands and gravels above a shale/limestone bedrock environment. Based upon the anticipated loading, drilled piers socketed into bedrock were recommended. The structures were constructed in accordance with the design recommendations.

Jan 1, 2007

By Helen Ahnberg

The scope of the present paper is limited to report the experimental evidence and not for describing the analytical assumptions. However, the idea behind the experimental program is that the deterioration may be caused by the leaching of Ca from the treated soil to surrounding soil or water driven by the difference in the Ca ion concentration. As a consequence of Ca leaching, it may be natural to expect the expansion of micro void space within the treated soil. In a saturated condition, the water inflow into the treated soil may accompany the leaching phenomenon. We measured the water content within the treated soil. But there is not much difference in water content within the soil.

Feb 10, 2003

By V. T. Ganpule

The effect of Sulphate and Chloride is well understood by the engineers. Most of the codes stipulate permissible limits for sulphate and chloride content in groundwater. Relatively few reference are available about the effect of organic acids on pile concrete. While executing a pile foundation work around Bombay, the authors came across the peculiar phenomenon. The routine testing of water has indicated that water is non-aggressive; however, on exposing the piles, the piles were found to be highly detonated. The testing of water on the guidelines followed by engineers associated with flow through pipes revealed that water is corrosive as per the Ryznar index concept. The present papers discussess the significance of Ryznar index in under water concreting.

Jan 1, 1996

By Wang Huichang

A tentative mathod for predicting load-settlement relationship and bearing capacity of single piles based directly on the results measured by cone penetrometer with local friction sleeve is presented. It is possible that the load-settlement curves can be constructed by means of CPT and the problem of both the bearing capacity and the settlement behaviour of single piles can be considered jointly. The proposed load-transfer functions are continuous, positive monotonic and nonlinear. a concept of weight mean point resistance 2D above and 4D underneath the pile base to determine the unit ultimate base resistance of piles is presented. The predicted results of seven jacked piles in loess are in good agreement with the load test data.

Jan 1, 1991

By Jeffrey A. Gebhard

As part of the design and construction of the new St. Anthony Falls I-35W Bridge, a full-scale load test was conducted on a 6 1/2-foot diameter drilled shaft in the St. Peter Sandstone. This load test helped identify shaft-rock interaction properties, including end bearing and multiple zones of differing shaft resistance for design of the drilled shafts beneath the three piers adjacent the river. The load test was designed by Load Test, Inc., Braun Intertec and the design team of Figg Bridge Engineers/TKDA and constructed by Design Build Consortium of Flatiron/Manson. Oversight was provided by the Minnesota Department of Transportation. Based on these test results, the drilled shafts supporting the St. Anthony Falls I-35W Bridge were designed to reduce risk and maximize economy for the people of the State of Minnesota.

Jan 1, 2009

By D. Vanni

Constructing new infrastructure in urban areas increasingly entails the use of sophisticated techniques for soil improvement in order to minimize surface disturbances in adjacent areas and damage to existing structures. In Naples, at the new Piazza Garibaldi subway station, TREVI built a 45 m deep shaft using a hydromill, and utilized soil freezing for the excavation of the four station's tunnels, fifty meter long, located approximately 30 meters below the water table. An innovative use of directional drilling was specially developed by TREVI to successfully complete this challenging job.

Jan 1, 2006

By David C. Kraft

Atlas Systems, Inc. (ASI) resistance type piers were used to underpin a 100 year old historic structure at Fort Monroe, Virginia. This 3-story structure with basement was underpinned with 155 steel tubular push piers (4" OD) that were hydraulically installed to depths ranging between 90 and 110 ft. and to installing forces in excess of 60,000 lb. Project requirements included lowering the basement floor by 1-1/2 ft. and constructing new footings and adding stem walls to connect to the existing masonry walls. Additionally, the underpinning piers were temporary which required the development of a decoupling system to permit the transfer of the building loads from the underpinning piers to the new footings. The structural loads at the foundation level required a c. to c. pier spacing of 3.75 ft. in order to meet project requirements of a minimum Factor of Safety of 3.0 on the pier load capacity. Project requirements included a load test on the selected underpinning pier (ASI - AP2 4000.219) in order to establish installation depths for seating the piers to 60,000 lb. The project was successful in supporting the full load of the structure during the construction phase. Considerable savings in time and cost were achieved as well as avoiding any vibrations or noise during installation of the piers.

Jan 1, 2002

By Stephen T. Bloomer

The application of a direct current electrical potential between a metallic pile and a fine grained soil results in an almost instantaneous change in the magnitude of the forces acting on the pile. During installation, with the pile connected as a cathode, the driving force needed can be reduced dramatically. Reversal of the polarity results in an increase in ultimate bearing capacity. The cause of the aforementioned phenomenon has been investigated and found to be two-fold; ie the electro-osmotic transport of pore-water and the electro-chemical hardening of the clay in close proximity to the pile. In the case of the former effect, the pore-water is transported towards the cathodic pile resulting in a temporary, reversible change in the engineering properties of the clay surrounding the pile. This effect is represented by a change in Skempton's Adhesion Factor (a). A total of one hundred and forty eight model tests was undertaken to study the change in the a valve using different types of metallic pile. The tests revealed changes in bearing capacity related to embedded length, skin-friction, end bearing and electro-osmotic gradient. It was shown in skin-friction-only tests that variations in soils strength across the soil profile caused by the electro-osmosis caused resultant changes in bearing capacity. This work is being carried out with the collaboration of Hercules Piling, a subsidiary of Stent Foundation Ltd.

Jan 1, 1996

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By Michel Bustamante

The original Cistercian Lure abbey situated in eastern France and built in the second half of the 16th century, has become nowadays an administrative building. Because it has been founded on poor ground conditions and inadequate foundation scheme, the abbey has suffered severe structural distortion. In 1992 an inspection revealed new extensive damages which led to a general refection together with a foundation underpinning. Micropiling was the selected method. Movements recorded over a period of 6 years after underpinning completion are presented.

Jan 1, 2002

By Jesús E. Gómez

A recent bridge underpinning project provided a unique opportunity to obtain information on the load-deflection response of 260 hollow-core bar micropiles. All production micropiles were proof-tested to a maximum load of 125 percent of the design load. In addition, four verification tests were performed on sacrificial micropiles to at least two and a half times the design loads. This paper presents the results of the verification and proof tests performed for this project, and provides recommended values for design of hollow core bar micropiles in soils similar to those encountered. This work shows that hollow core bar micropiles provide a significant unit bond capacity in both granular and fine soils, which may be greater than that typically expected in pressure-grouted (Type B) micropiles. The hollow core bar system allows faster installation rates in the soil types encountered than other traditional micropile techniques, and can be installed with relatively simple quality control procedures.

Jan 1, 2007

"Premissas BásicasCaracterísticas do concreto centrifugado(Spun concrete characteristics)Aplicação em obras de engenharia de fundações(Application engineering works foundations)Logística de fabricação e transporte(Manufacturing logistics and transportation)Emendas x uso de aplicação(Amendments x use application)Geologia brasileira, da região costeira a presença de grandes bolsões de argila mole(Brazilian geology, coastal region the presence of large pockets of soft clay)Influencia do sistema de cravação(Influence of driving system)Transferência da Energia Aplicada(Applied Energy Transfer)Estacas longas(long piles)Controles executivos (diagrama de golpes, nega, repique elástico, ensaios de carregamentodinâmico, provas de carga).(Executive Controls (blows diagram, sets, elastic rebound, dynamic load tests, load tests).)ECD – aplicação da metodologia do DIETECD - application of the methodology DIETBrazil has a highly variable geology all along its coast that directly influence the choose of foundation type, being too employed the use of reinforced spun concrete piles initially ranged in diameter from 60 to 80 cm. Over the past 10 years with the advent of investment in marine works projects began to demand a new range of piles with diameters greater than 100 cm and in the absence of amendments.On land is also very remarkable the presence of regions with large layers of soft clay, in prime areas that have been explored. A classic example is the Barra da Tijuca in Rio de Janeiro that has suffered from the housing boom growing toward these regions. In these regions it has been very common driven lengths of about 40.0 meters, which basically go through thick layers of soft material or unconsolidated and they will find strength in depth with residual soil layers or even the bedrock.The spun concrete has great qualities for application in deep cuttings resulting from the production process, which gives a redistribution of fresh concrete mass collaborating with the particle size distribution effective loss of water that is thrown to the center stake being subsequently discarded. Consequently this contributes to a reduction in the factor a/c that is directly connected to increase strength.The fact that there is a sort of concrete helps to reduce voids in the mixture, which increases the durability characteristics. This condition made it possible to employ the spin technique on poles, which are directly linked to aggressive media in large urban centers.Another very attractive feature is that the centrifuge process can work with concrete with the lowest percentage of mortar and more gravel. This concrete mix directly contributes to increasing the specific modulus of elasticity, thus allowing a greater capacity to absorb the energy of the blows transferred with less deformation.Despite the great potential of land application of prefabricated spun concrete stakes there are only three factories and its limitation is the cost of transporting manufactured for the various regions, since all transportation is done by road.For its transportation is carried out exclusively by trucks, this limits the size of cuttings being produced commonly in length from 11.0 to 12.0 meters in length and smaller compositions. For use in long piles of works is resorted to amendments in the form of metal rings, concreted near the ends of the stakes, with the transfer through steel bars in CA-50 welded to the ring. Usually run in steel ASTM A-36. Later in the work these rings are welded with coated electrode.In the case of maritime stakes are very used to drowned splicing technique, which basically consists during the spin process leave one end with the armor of the apparent stake and work together two elements and make specific, with superior resistance to the prefabricated stake.This study in addition to briefly introduce the process of manufacturing, design and logistics presents a detailed study of applicat"

Jan 1, 2015

By K. Rama Sarma

Piles are frequently subjected to lateral forces and moments in addition to vertical forces and hence the piles have to be designed for both lateral loads as well as vertical loads. In the design of such pile foundations, two criterias must be satisfied. First an adequate factor of safety against ultimate failure and second, as acceptable deflection at working loads. In this study the work has been carriedout to study the lateral deflection pattern of the pile. The solutions to the problem primarily depend on soil modulus. Equations for computing the values of slope, deflection and coefficients for many types of soil conditions have been developed for static loading for long piles. As analysis part is not available for the above methods for the values of depth coefficients in the tables. It is required to go for linear interpolation which is not valid and highly unreliable. In this present method, coefficients can be obtained for any value of depth coefficient (z) with simple calculation. The present method is very concise and allows one to ana­lyse any type of pile with varying depth coefficient (z) even without the availability of any practical data regarding applied lateral load (P1) and moment (M1).

Jan 1, 1996

By Mohammad T. Izadi

Piles are, often, used for transferring load from the super structure through soft consolidating strata onto relatively stiff uncompressible soils. Downward movement of the soft soil strata develops negative skin friction and dragload around the pile shaft, with time. Traditionally the induced dragload is considered in determining the pile bearing capacity. On the other hand, field measurements on instrumented piles show that negative skin friction is reduced by the magnitude of applied live load. A method for calculating the pile bearing capacity, driven through soft consolidating strata is presented. In this method, two allowable load-bearing capacities are calculated for each pile, live load plus dead load and dead load. The proposed method, substantially, increases the allowable load bearing capacity of piles compared to calculated values by the traditional methods.

Jan 1, 2001

By David White

When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100? of water are well known, let alone in the open waters of the South China Sea. In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130? long, 72? diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE?s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.

By David White

"When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100’ of water are well known, let alone in the open waters of the South China Sea.In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130’ long, 72’ diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE’s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.INTRODUCTIONThe challenges of driving individual steel sheets in deep water are well known, let alone in the open waters of the South China Sea. Often the challenges of construction are overcome with engineering or equipment. The challenges of China’s Hong Kong-Zhuhai-Macau Bridge, on the drawing board since 1983, were to overcome both. The challenges of overcoming the skepticism of the Chinese Engineering community would be another story.The finished project will comprise three cablestayed span bridges and a 4.15 mile immersed tube tunnel linking Hong Kong on an eastern span to the China mainland cities of Zhuhai and Macau via two western spans."

Jan 1, 2017