Search Documents

By Hiren J. Shah

Across much of New York City, the geology of glacially deposited soils follows a common sequence. Outwash sands generally overlie varved silts and clays, which lie above a basal till deposit underlain by the bedrock. Pile foundations at projects with such typical stratigraphy generally develop their axial capacities by extending below the fine-grained deposits into the till or the bedrock. Contrastingly, at a project site on the Brooklyn waterfront, high capacity piles were efficiently and economically installed by driving them into the relatively shallow glacial drift and till deposits which lay above thick fine-grained compressible glacial lake deposits. An unusual aspect about the foundation design at the Brooklyn project site is that, relatively short and high capacity piles were driven into the shallow glacial drift and till deposits, overlying the thick fine-grained glacial lake deposits. In order for this unusual foundation scheme to be feasible and economical, the piles needed to achieve their driving criteria in the upper strata. Consolidation settlements in the lower stiff and over-consolidated glacial lake deposits below the pile tips had to be relatively small. The paper discusses the unusual stratigraphy in this area of Brooklyn in greater detail with geologic profiles and engineering characteristics of the glacial strata. It also discusses the design aspects of the pile foundations, settlement estimates, a pile drive test program during design, results of the static load test program during construction, and production pile installation results.

Jan 1, 2008

By Colin Curtis

The City of Manchester is hosting the 2002 Commonwealth Games. A world class Stadium with a 38,000 capacity was commissioned for a site located close to the City Centre. The Stadium location is in an area that was derelict and in need of regeneration and it is envisaged that the Stadium will be the spur for this. The industrial and residential history of the site has left a legacy of buried foundations together with chemically contaminated soils. This Made Ground deposit overlies Glacial Deposits which in turn overlie bedrocks of the Central Manchester Coalfield. Coal mining has taken place from at least 1761 leaving several worked seams and shafts. In order to support the stadium, 1159 conventional augured piles of 600 to 1200mm diameters were used. This paper will deal primarily with the piling operations and testing, but will also discuss the coal seam treatment with respect to piling. A substantial trial pile test programme was carried out together with 11 static load tests on contract piles. The results of the pile tests will be discussed and conclusions drawn.

Jan 1, 2002

By Abid Adekunte

"Whilst safety is considered to be of high priority in every aspect of engineering projects, it is equally important for designers and contractors to be continually aware of their obligations to the immediate environment and the society as a whole. These include responsibilities to minimise the amount of nonrenewable natural resources and energy used on projects, to reduce carbon foot prints on projects, to minimise the quantity of wastes produced on projects, to minimise the level of pollution on construction sites and to reuse materials and waste products whenever and wherever possible.In other words, professional engineering practice needs to be accompanied by an underlying fundamental objective to improve, restore and sustain the environment. However, achieving this objective requires continuous collaborative interaction and effective communication between the different specialists involved on every project from the early stages. In addition, developing a well-thought-out economical solution is key to achieving the sustainability aspect of the above objective.This paper focuses on the design, construction and management of a recently completed large multi-level basement scheme in Central London, with greater emphasis on collaborative approaches taken by the design engineers, commercial managers, construction managers and site operatives to deliver the most reasonably economical and sustainable solutions to the client. Solutions were based on combinations of general and specialist engineering knowledge, with due considerations for health & safety, sustainability, cost, practicality, time and community requirements.INTRODUCTIONUnderground structures have become vital components of urban life worldwide e.g. tunnels serve many water, wastewater, highway and railway schemes, basements have been incorporated into many urban commercial, institutional and residential developments, while many public underground car parks have been built to deal with the incessant problem of insufficient surface parking spaces in busy urban centres.The safe design, construction and maintenance of underground structures have been well-mastered by the deep foundation industry over the years. However, just like many other areas of engineering, aside the need to satisfy safety requirements, underground construction practice is now faced with a new set of requirements; the demand for more sustainable and cost-effective solutions, with reduced environmental and societal impacts. Designers and managers of underground construction schemes are now compelled to minimise the use of natural resources and energy, to minimise the amount of waste produced, to minimise the level of environmental pollution, noise and disruption to traffic and normal societal life at ground level around underground construction sites. In addition, the recycling of site wastes and reuse of materials have now become important aspects of underground space development. Considerable effort is being put into promoting sustainable development across the industry."

Jan 1, 2017

By Daniel W. Mageau, Larry W. Applegate, Aaron K. McCain

"An innovative method of ground freezing was successfully tested to create a “dry” excavation condition for a new building foundation at a site in downtown, Miami, Florida. The subsurface conditions in Miami generally consist of very porous, weak limestone and sand with groundwater near the surface. Water flow through these materials can be very high. Dewatering is extremely restricted in Miami so deep below-grade structures are rare and expensive. A new, innovative method to allow deep excavations in dry conditions without dewatering involves the creation of a thick, temporary, frozen soil plug below the planned excavation depth across the entire site to cut off vertical groundwater flow during construction. Frozen soil is impermeable and very strong and has long been used for temporary structural and water-tight shored walls. Using the same proven principals, frozen soil plugs are very effective at cutting off water from the bottom of the excavation as well as resisting upward buoyant forces. This new freezing method can be used for fairly deep excavations in new building construction supported on deep foundations. The building piles act as temporary anchors for the frozen plug to resist very high upward buoyant pressures until the permanent structural slab is completed.IntroductionUnlike other Cities, below grade basements are rare in Miami. The few basement foundations constructed have utilized a cumbersome and expensive method of excavation and shoring involving underwater excavation, tremie slabs, and commercial divers. The key issue for underground construction in this area of the country is the vertical flow of groundwater through the base of the excavation. To deal with this issue in the past, the contractor first installed all of the building piles and the perimeter shoring walls. Then, interior sheet pile walls are installed to create small manageable excavation pits. Each pit is then excavated through standing water “in-the-blind” and around the buildings support piles. The final excavation, interior struts, and inspection is performed by commercial divers. Finally a thick foundation tremie slab is poured under water. This method could be successful but proved to be time consuming and expensive. In addition, some building piles were occasionally damaged during the under-water construction process."

Jan 1, 2015

By John Dunn, Matt Hawley, Kashif Butt, Nicholas Gura

"This paper presents the results of a static load testing program completed on helical pile foundations for the replacement of high voltage transmission line tower structures. The foundations were part of the Northeast Grid Reliability Project (NGRP) for the Public Service Electric & Gas Company (PSE&G) near Newark, New Jersey. Structure foundations “anchor bolts down” was a design build contract model with the superstructure as bid-build.The soil stratigraphy along the alignment generally consisted of fill over about 10 ft of organic deposits underlain by up to 260 ft of normally consolidated glacial lake clays and silts. Additional project challenges included working under/adjacent the existing live high voltage lines, narrow site access due to environmental permits, foundations in a tidally influenced area, and pile projections in the order of 10 feet to meet the 10 year flood level requirements.The helical piles were constructed of 12.75 inch diameter open ended pipe piles with 36 to 40 inch diameter helices. A total of seven static load tests (compression and tension) were completed on 60 ft and 90 ft long piles, using both welded and mechanical pile splices. To evaluate pile-soil setup in the sensitive fine grained soil and determine representative longer term installation torque factors (Kt) for the production piles, the static load tests were performed 7 to 49 days after pile installation.Helical piles were found to be the most cost effective foundation alternative for this project. The required length of helical piles was less than other alternatives for similar allowable axial capacity. Helical piles with mechanical splices were installed for the varying structure foundations including tangent and heavy deadend, to a deadend monopole. Installation of 448 production piles (34,320 linear ft) was completed in three months. The installation timeline was critical to meeting the semi-annual PSEG outage for switching the old and new structures. Helical piles employing a mechanical splice resulted in an efficient and effective foundation solution for the conditions encountered on the project."

Jan 1, 2017

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

By Max Gwynn, Tony Suckling

"The new Wembley Stadium is the most spectacular soccer stadium in the world, built to the highest specifications, using the latest technology and offering visitors an unrivalled match-day experience. Wembley Stadium is the home of English soccer, dating back to 1918 when the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Empire Stadium, as it was originally known, was completed in 1924 in just 300 days and cost £750,000 ($1.4m). It was finally closed in 2000.The new Wembley Stadium, which opened in 2006, features fully covered seats for 90,000 fans and a striking arch that sits above the northern half of the stadium. With a span of 315 m (1040 ft), the 133-m (440-ft) tall arch is the longest single-span roof structure in the world. It supports the entire weight of the northern roof and 60% of the weight of the southern retractable roof. This means there is no need for columns within the stadium and ensures unobstructed views.Multiplex Constructions (UK) Ltd. employed Stent Foundations Limited to construct the £10m ($19m) foundations package for the new stadium. The scope of works for the foundation package included the design and construction of all foundations, including all main works piling, temporary works piles for the arch and roof, and tower crane piles. The scope also included trial piling and pile testing, setting out and removal of spoil.Piles were constructed by using bored cast-in-place techniques with both hydraulic and traditional crane-mounted rigs. Stent also installed sheet-piled walls at three locations to the site’s northern boundary. In addition to the main contract works, Stent constructed a £2m ($3.8m) contiguous bored-pile retaining wall within the demolition and earthworks package (Figure 1). This work was carried out as a subcontractor to Griffith McGee."

Jan 1, 2008

By Dario Libano, Franz-Werner Gerressen

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. Of course they can also be used as deep groundwater barriers. This paper will focus on the construction work in an urban area like Sao Paulo. The Line 5 of Metro Sao Paulo is one of four network expansion projects undertaken at the same time. The projects will cover various areas of the city. The Line 5 on São Paulo’s south-side will be extended 7.1mi (11.5km) to serve 770,000 riders per day, stretching a total of 12.4mi (19.9km) along 17 stations. The extension line will facilitate access to the city’s central section and the commercial and hospital districts located along the line. The Brooklin Station, subject of this paper, had to be carried out in a special five shaft shape design, shaft diameter 131ft (40m) each, without using ground anchors. A focus will be taken on the special requirements of the installation of the arrows as well as on the specialties of installation for the shaft shaped layout. Therefore, it was required to install a 3.3ft (1,000mm) diaphragm wall using a specific layout especially in the connecting sections of the shafts, the so called arrows, to provide a bearing area for the struts. Maximum wall depth was about 121ft (37m); the total volume was about 20,060 cubic yard (15,337m³). The paper will describe the construction method and the sequence of activities required for the construction of this diaphragm wall using a combination of hydraulic grab and trench cutter system.INTRODUCTIONThe Line 5 Extension, in the city of Sao Paulo/Brazil, is currently the most important investment in public transport by Sao Paulo state’s government. It will connect the south part of the city to the city center, crossing through four other major METRO lines and stations, all currently in operation. The extension includes a new parking yard for the trains and 11 new stations. The Brooklin Station is one of the new stations and has a unique geometry of five secant shafts. The station should open and operate in 2016.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One of them was to contain the contamination plumes in the neighborhood and the other for temporary support to enable the excavation of the shafts. The final retaining wall design was reviewed and changed to a concrete structural diaphragm wall. The reason of design change was as well the reduction of construction time of the shafts by half to meet the schedule as to avoid dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a trench cutter (hydromill) was used in such a situation in Brazil. The cutter increased the quality of the joints by overcutting, and decreased the probability of having seepage into the shafts. The cutter created a seepage barrier and avoided movement of contamination."

Jan 1, 2017

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Dennis Wrixon

It was a little bit exceeded. The decision was the uniform settlement is measured at each one corner and the highest one corner is the important one. And in addition there is a differential settlement of 2.1 mm allowed. So we reached about 7.8 or 7.9 mm with the highest corner and in addition 2.1 so it was a little too much. But behind there is a very difficult calculation of the authorities where all of the displacements are combined together and there are of course some more factors of safety in these settlements.

Feb 10, 2003

By Michael J. Marasa

"Geotechnical engineering and construction primarily relies on the subsurface characteristics of the particular site; however, obtaining both accurate and precise information on those features is challenging due to the numerous factors involved in testing procedures used to analyze varying site geology. This includes a detailed and thorough geotechnical investigation to understand the site conditions, allowing the implementation of the most practical and economical solution.This paper presents a case history of the installation of wick drains and construction of aggregate piers on the site of a large facility to be constructed in Memphis, Tennessee. Throughout intensive subsurface investigations, highly variable soils were encountered, requiring settlement control and increased bearing capacity. This paper will discuss the design and installation of the systems constructed, and procedures and execution of the work to ensure design specifications were achieved.BackgroundA 1.4 million square foot expansion directly adjacent to an existing 1.1 million square foot distribution facility in Memphis, Tennessee was planned to serve as a centralized facility for increased production. The first phase of construction included an 858,000 square foot warehouse and parking lot for approximately 400 trucks to the north of the existing structure. The anticipated column load for the warehouse was 125 kips; slab design bearing pressures ranged from 200 to 500 pounds per square foot (psf) and elevations ranged from EL. 264 to 282. Parking lot elevations ranged from EL. 264 to 290, requiring a design life of 10 years with an estimated 100 in- and out-bound trucks daily and maximum weight of 80 kips per truck. The second phase of construction took place east of the existing structure, and included a 794,000 square foot multi-level warehouse, a 100,000 square foot office, and additional employee parking. The anticipated column load for the second warehouse was 225 kips and slab design bearing pressures ranged from 200 to 500 psf. Elevations ranged from EL. 267 to 282. Anticipated column loads from the office were 25 125 kips, with slab design bearing pressures ranging from 100 to 200 psf. Due to the varying elevations within each planned footprint, up to 18 feet of new fill was required to match the existing structure’s finished floor elevation (FFE) at EL. 282."

Jan 1, 2017

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By David R. Sutfin, Joseph Lodde

110 N. Carpenter is new commercial building located in the West Loop neighborhood of Chicago, Illinois. The new home to the McDonalds Corporation work headquarters, accelerated project delivery methods were essential to meet the scheduling demands for this project along with other projects slated to start in the region. As such top-down construction methods were utilized to allow for above and below grade construction to proceed in parallel in lieu of more conventional bottom-up construction methods, thus compressing the project schedule. To achieve this plan, perimeter secant pile walls were constructed in conjunction with interior columns/drilled shafts and a shear wall core constructed from inside a temporary cofferdam. The use of secant pile walls allowed for efficient accommodation of a variety of loading conditions including: exterior curtain walls loads, perimeter column loads, tower crane foundation loads, and in-plane shear loads. Furthermore, this system allowed for efficient and fluid operation of equipment on site in order to accommodate the 90-day window allotted for initial foundation construction. INTRODUCTION 110 N. Carpenter is a recently-constructed 9-story commercial building located on the old Harpo Studios property in the West Loop neighborhood of Chicago, IL. The construction of this 55,750m2 (600,000 ft2) structure is significant to the continued commercial development of Chicago as nearly 46,450m2 (500,000 ft2) of the building houses the new world headquarters for the McDonald’s Corporation, which had moved from Chicago to the suburb of Oak Brook in 1971. McDonald’s recommitment to this urban environment is not only a reinvention of the long-established fast food giant but the anchor for a broader redevelopment of the West Loop neighborhood. Since the opening of this building was seen by the developer, the City of Chicago and others as a key to future local projects, innovative solutions were required to showcase forward-thinking design as well as expedite the construction process. The final result of the design/planning process is a structure consisting of nine levels of above-grade commercial space and two levels of below-grade parking, providing approximately 300 parking spaces. The above-grade structure consists of a reinforced concrete flat plate system, including two-way slabs, columns, and two core/shear wall systems for lateral support. With an average depth of 7m (23ft), the below-grade structure consists of interior components similar to the above-grade structure (structural slabs, columns, shear walls) but includes a perimeter secant pile wall that was designed to support lateral earth pressures; vertical forces from the exterior curtain walls, perimeter columns, and the construction tower cranes; and in-plane lateral forces to reduce the demand on and quantity of interior shear walls. The use of a secant pile wall is a key component to the project because it accommodated the use of top-down construction methods to accelerate the construction schedule.

Jan 1, 2019

By Vivian M. Troughton, Clifford J. Wren, Tony P. Suckling

"Secant pile walls are used for the construction of deep basement walls and earth retaining structures. Risk associated with secant pile walls is commonly perceived as being the safety of site personnel and the public during piling operations, or safety used in design. It is recognized that both of these are of paramount importance, but additional risks associated with the construction methods must also be considered to complete the risk management profile for any project. For the particular case of secant pile walls, if Clients take a ""back seat"" they may be unaware of the total risk package they are procuring. The authors argue that the piling contractor should be involved at the earliest stage giving input into the overall risk management process. Such early involvement within the professional team will maximise cost benefits to the Client and minimise the delays and cost increases sometimes associated with these works. A consistent methodology for identifying and then managing all the risks associated with secant pile walls is proposed. An example is used to demonstrate how this methodology should be employed. INTRODUCTIONThis paper discusses the value of a complete and integrated risk management process for structures with basements formed using a secant pile wall.The risk associated with any secant pile wall can be consicfered as comprising four components;1. Safety of people on site2. Safety of design or design methodology3. Construction risks4. Commercial risksAny risk management system needs to fully consider and integrate each of these four components to maximise the likelihood of a successful outcome for the basement.This paper concentrates on the construction risks for secant pile walls, as these are not often understood by the Client (in this paper the term ""Client"" also includes the main contractor, principal contractor, Engineer, Planning Supervisor, quantity surveyor and cost consultant)."

Jan 1, 2005

By Peter Smith

One New Change is a landmark retail / commercial development in the City of London. Integral to the structure is the three double storey basement from which the building is serviced. The building construction involved a ?top down? (up down) construction technique to give programme benefits. In addition, the planning authority stipulated that 10% of the energy demand had to be met by Renewable technology. Cementation Skanska has not only delivered the foundation package - comprising secant piling and foundation bearing piles including Cemloc® plunged columns - but, alongside subcontractor Geothermal International, also installed a 1.7MW ground source heating and cooling system using Energy Piles® and open?loop wells to provide the renewable energy. The works were successfully installed and completed within a tight programme, and within the logistical constraints imposed by an inner-city location, concurrent demolition works and multi contractor involvement in the basement construction.

Jan 1, 2010

By Huw Williams

"Power companies are always looking to increase the carrying capacity of existing transmission lines, and the preferred method is to string heavier capacity conductor lines. However this results in higher wind loading and the potential for towers overturning, if the existing foundations do not have the tensile capacity. On older lines, there is often a lack of information on construction type and dimensions and in practice the as-built foundation can differ considerably from design drawings, due to unforeseen ground conditions along the line route, and no record of the resulting change in design being made.Following successful trials in New Zealand, integrity testing with Frequency Response and impedance profiling techniques is now being used in the region to check concrete foundation properties in-situ and are enabling power companies to get the most out of their assets. INTRODUCTIONIn most regions of the globe, the US included, there is generally a requirement to upgrade transmission line capacities, to cope with increasing power consumption. Problems with under capacity only come to light for the public when blackouts occur, even in developed countries.A large number of transmission line towers are designed with a certain capacity redundancy and will be able to carry greater loads than originally designed for. Power companies are therefore looking for ways to assess their assets and to minimize the costs of upgrade work.Re-assessment of tower foundation capacities using design drawings may not be valid , as constructed foundations may differ considerably from design drawings, to accommodate local difficulties and in some instanced, particularly with earlier lines, there is no information whatsoever. This complicates efforts to determine the capacity of foundations considerably."

Jan 1, 2005

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. One can anticipate that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Complex conditions in terms of space limitations, especially for inner city job sites, require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Furthermore, one focus will be given to the QA/QC topics of the production process. Real time installation control, data transfer and reporting systems become more and more important. Therefore, the paper will describe the construction method and the sequence of activities required for the construction of diaphragm wall systems. It will describe also the main equipment that will be needed to execute these works under various conditions. In addition to the general description of the system and the required equipment, the paper will show some site examples for infrastructure projects with their specific solutions when working under space restrictions.

Nov 1, 2022