Search Documents

By D. Harris, S. Murugesan, G. Ye, G. Oprea, J. Rigby, T. Troczynski

The spinel-added and in-situ spinel bonded castables have been developed and widely used in steel industry. It is challenging to develop magnesia-based castables for the non-ferrous industry because the temperatures in industrial furnaces are significantly lower than those in the steel industry and therefore the binding systems of these castables must have the capability to develop a ceramic matrix below 1300°C. It is also challenging to develop a good binding system without addition of fume silica, because the hydration of magnesia may take place during installation, curing and firing of the castables. This work presents the experimental results on developing magnesia-based cement-free, silica fume-free refractory castables using hydratable alumina as the hydraulic binder and a spinel phase as the final ceramic binder. In order to activate the sintering and have a ceramic matrix well developed at the relatively low required temperatures, ultrafine aluminas, chromia, magnesium-aluminate spinel and aluminum titanate powders were used as components of the binding system.

Jan 1, 2004

By S. Parada, P. T. Jones, M. Guo, S. Smets, E. Boydens

The corrosion behaviour of a pitch-bonded MgO-C refractory in contact with a vacuum oxygen decarburisation slag with high Al2O3 content (12-17 wt%) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterisation of the corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature, corrosion time and the Al2O3 content in the slag is discussed. The degradation mechanisms include slag infiltration, direct MgO dissolution from the refractories into the penetrated slag, erosion of magnesia grains at elevated temperatures, removal of carbon through the MgO-C reaction, and finally, oxidation of refractory carbon by reducible slag components. Both a porous MgO layer and a dense (Mg)(A1,Cr)2O4 spinel at the slag/brick interface were observed. Their formation mechanisms and industrial relevance are discussed.

Jan 1, 2004

An optimization process is described that can be systematically applied by mine planners to produce life-of-mine schedules aligned with their strategic targets, while maximizing the net present value of the mining operation. The software tool employed uses heuristics and an evolutionary algorithm to generate life-of-mine schedules of production and development activities. Generating such schedules is typically a very difficult task due to the large number of operational constraints that must be respected, and the vast number of alternative schedules; as a result the value of the mining operation can be compromised. With an expansion at Newmont?s Leeville mine in Nevada, the mine planners were given the task of producing feasible life-of-mine schedules with significantly increased production rates. Their initial efforts indicated that it would be a considerable challenge to generate such schedules in a timely manner. By systematically applying the proposed optimization process, the mine planners were able to generate optimized life-of-mine schedules with the desired production rate.

Aug 1, 2013

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson?s ratio, P-wave, Swave velocity, point load test index, crushing and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with low strength detonating cord, to combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

May 1, 2003

By Daniel Gendron, Luc Morin

"Concentrate sampling is a growing concern in the world's mining and smelting industry. The main modes of transportation for concentrate to the smelter are by truck or rail car in a bulk form, thereby limiting access to sample extraction equipment. In many cases, concentrate is shipped to a smelter by several suppliers therefore requiring individual manipulation of different customer samples in a safe and reliable manner. The Heath & Sherwood Bulk Product Sampler offers this feature as well as an economical and effortless way of obtaining samples in rail cars or truck boxes.In 1994, Noranda Metallurgie in Rouyn-Noranda, Québec purchased a self contained Bulk Product Sampler to extract samples directly from inside rail cars before unloading the concentrate. After testing and comparing the results with the conventional sampling method, the bulk product sampler proved to be a practical and advantageous solution for concentrate sampling both for the customer and smelter. Since its installation at the Horne smelter in Rouyn-Noranda, the Bulk Product Sampler has been steadily used on rail cars which contain concentrates from around the world."

Jan 1, 1996

By Mario A. Morin

Over the years, several sources have stressed the need to better integrate the underground mine design and planning processes. The belief is that with better integration, better designs and plans will result - designs that are ?optimized?. Some researchers have focused their efforts on data integration, others have looked at closing the loop between production control & monitoring with mine planning & scheduling. In spite of all these efforts, fully integrated applications combining geological modeling, stope design and geomechanics, mine planning and scheduling, rock extraction and material handling system design, mine support systems, economic analysis with production control do not yet exist for the underground hard rock mining industry. There are several likely explanations - some economic, some technical. It is certain that the design and planning processes are interrelated and interdependent and thus are extremely complex to describe and understand. The mining engineer has an appreciation of the complexities involved - but how does he convey this knowledge to a programming team responsible for developing an integrated design & planning system. This paper will focus on software engineering methods, and other possible approaches, to describe and manage the complexities inherent in the underground mine design and planning process and the development of an integrated computerized system.

May 1, 2001

By A. Jeffkins

Visibility is restricted when operating load haul dump vehicles resulting in a number of serious accidents in the Ontario Mining Industry. One of the leading causes of these accidents is the inability of the equipment operator to see clearly people, objects or hazards around the machine. Previous line of sight testing by the research team found specific machine characteristics were responsible for blind spots and impaired visibility. In order to identify feasible design modifications a computer simulation program, Classic JACK 3.1, was utilized. Program features include human factors analysis, which allows evaluation of line of sight and operator posture in order to decrease risk of musculoskeletal injury. Research within the virtual computer environment consisted of a Visibility Audit and a Target Audit in order to quantitatively determine how certain components of the LHD design affected the line of sight around the vehicle. Results indicate that modifying the LHD light brackets, engine profile, cab posts and other components will enhance visibility. The addition of cameras located on the front and rear of the vehicle were able to enhance the operator?s sight lines to previously obstructed areas. Modifications to seat height and the operators orientation both improved sightlines and decreased risk factors associated with back and neck musculoskeletal disorders.

May 1, 2003

By Patrick R. Stephenson

The Australasian Code for Reporting of Mineral Resources and Ore Reserves (the ?JORC Code?) has been operating successfully for 14 years, and has an ancestry dating back over 30 years. Together with complementary developments in stock exchange listing rules, the Code has brought about substantially improved standards of public reporting by Australasian mining and exploration companies. The Code is regarded as a world leader in its field, and has been used as a basis for the development of resource/reserve reporting standards in other countries. The reasons for its success are varied, foremost amongst them being its adoption in full by the Australian and New Zealand Stock Exchanges, and the ability and willingness of mining industry organisations to bring Competent Persons to account when necessary. The latest revision of the JORC Code was undertaken in 2002/03, based in part on releases of upgraded reporting standards in Canada, United Kingdom/Western Europe and South Africa, and the 2003 edition is expected to be released mid-year. Two of the more significant changes are: the introduction of a requirement for a Competent Person to be responsible for the documentation upon which Exploration Results are reported; and inclusion in the definition of a Competent Person of a reference to ?Recognised Overseas Professional Organisations?, being overseas professional organisations to which Competent Persons may belong for the purpose of preparing documentation for the submission of reports to the Australian Stock Exchange.

May 1, 2003

By Chan-ho Park

As the building has recently become bigger, higher, and freeform, a technology called BIM(Building Information Modeling), which is a key technology that integrates construction and IT(Information Technology), has been rapidly introduced and expanded. Because BIM technology offers various benefits, countries that introduced BIM early has been actively promoted. However, misperceptions of BIM are prevalent in countries such as South Korea that have adopted it relatively late, with lack of awareness of its fundamental purposes. Under these circumstances, transparent and quantitative performance assessment needs to be executed in order to eliminate the misperceptions, and to explain and revitalize the BIM introduction. These quantitative performance measure KPI (Key Performance Indicators) to be measured should be prioritized. As derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, Uses the BSC to seek a balance between short-term financial goals, values and the value of long-term goals. Uses the BSC(Balanced Scorecards) to derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, seeking a balance between the value of short-term financial objectives and the value of long-term objectives. Through this, the KPI (Key Performance Indicators) which is used for measuring the effect of the BIM will be generated and also the method that can determine whether the generated KPI figures are objectively inter-connected will be suggested as well.

Aug 1, 2013

By Christopher H. Clement

The International Commission on Radiological Protection (ICRP) is an independent, international organization that advances for the public benefit the science of radiological protection, in particular by providing recommendations and guidance on all aspects of protection against ionizing radiation. This presentation touches on aspects of The 2007 Recommendations of the ICRP, a fundamental document that lays out the system of radiological protection for all exposure situations and types, and focuses on other recent publications relevant to the uranium industry. Of particular relevance are the 2009 ICRP Statement on Radon and the accompanying report on lung cancer risk from radon.

Aug 1, 2010

By Y. A. Grinin, M. A. Liamina, V. A. Shumskij, Y. I. Sannikov, M. V. Radashin

"A brief history of the development of the Kivcet flash smelting process is presented. The broad scope of the process with an ability to treat high grade lead sulphide concentrates, as well as oxidized lead-zinc residues, is emphasized. Fine coal in the charge serves two purposes, one as auxiliary fuel and the other as a pre-reductant for ferric iron in residues. Current Kivcet operations incorporate a layer of coke or “coke checker” at the surface of the slag in the reaction shaft that acts as a reducing agent for flame products or slag that flow through it. Details of this invention, are given. IntroductionFor many years, the sinter-blast furnace lead smelting process has been the main internationally accepted method used for the production of primary lead metal. In recent times, this process has been unable to meet legislated environmental restrictions and it became clear in the mid-1960s that a new and cleaner process would have to be developed. The present level of Kivcet performance was developed in three main stages:1. flash smelting natural sulphide lead raw materials with the attached electric furnace for production of lead bullion and crude zinc;2. natural raw material smelting with lead and zinc separation in a “coke filter” or “coke checker” at the surface of the slag in the reaction shaft to produce lead bullion and ZnO-bearing slag that can be fed to conventional slag fuming; and3. processing of oxidized lead-bearing raw materials, such as low grade zinc plant residues, with the production of lead bullion and ZnO-bearing slag periodically directed to slag fuming."

Jan 1, 1998

By Jef M. van der Zel

The idea of veneering rich yellow gold alloys with a low-melting, high expansion porcelain, has been a driving force for metal-ceramic research in dentistry. Since 1990, with the advent of the Carrara System (1), a low firing temperature veneering ceramic allowed the use of gold alloys with a lower content of platinum and palladium than the traditional gold-platinum ceramic alloys and thus a richer yellow color. The earlier high gold-platinum ceramic alloys contained at least 12 percent platinum group metals to allow for dimensional stability when firing the relatively high melting traditional ceramics. This amount of platinum group metals gave the alloys a greyish tinge which made them unattractively steel colored and difficult to present as ?high gold alloys?. In the 90?s the new generation universal low-melting, high expansion gold alloys gained market share at a steady rate, starting in Germany, and have now for a great part replaced the traditional gold-platinum alloys (Fig. 1). The first alloys contained 75 wt-% gold and up to 9 wt-% platinum or palladium. They provided a metal-ceramic system in which a gold alloy having an aesthetic yellow colour is fired on with a dental porcelain tailored thereto. The tailoring is meant in respect of compatible coefficients of thermal expansion, and compatible melting or softening points of metal and porcelain. The major concerns in the beginning were with thermal stability during firing, the thermal expansion coefficient of the alloy against the porcelain (compatibility) and the yellow color. In a later stage, alloys with gold contents in the range of 50-60 wt-% gold were developed in analogy with the pale yellow gold-reduced alloys that were formerly used for crown & bridge work and the white gold-reduced alloys used for metal veneering where gold was substituted in part by palladium.

Oct 1, 2003

By G. Yan

The gas diffusion layer (GDL) is one of the most critical components of the proton exchange membrane fuel cell (PEMFC) in achieving good performance. The GDL serves as a current collector, transport media for fuel and oxidant to the catalyst layers, a support for the catalyst layer and a medium for water management. In this paper, we will discuss the modeling and experimental measurement of the reactant distribution in the GDL and to the catalyst layer. This will be done for some new and advanced engineered GDLs. Novel optical technique which correlates measured data with reactant distribution are used. This technique combined with modeling allows optimal design of engineered GDLs.

Jan 1, 2005

In this paper, the use of electrochemical AC impedance spectroscopy (EIS) for in-situ diagnosis of high temperature PEM fuel cells is described. EIS was performed on single cell hardware, built in-house, using a fuel cell test station modified to operate up to 120°C and 30 psig. Electrode kinetics, membrane resistance, porous-layer and mass transport impedance of MEAs, assembled in-house, were measured at various current densities for the purpose of validating the test station and cell hardware, and for optimizing MEA and flow-field designs. The effect of temperature and humidity on the various impedances was investigated. Impedances obtained at lower and higher temperatures were compared to obtain insight into the issue of water management in operating fuel cells.

Jan 1, 2005

By John Oxenford

There are currently two operators producing oil from the surface-mineable portions of Alberta?s oil sands (Syncrude Canada Ltd. and Suncor Inc.) and two other companies are proposing to enter the industry (Albian Sands in 2002 and True North in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of recoverable TiO2 and approximately 80 000 tonnes per year of recoverable zircon. This represents approximately 6% of the world?s TiO 2 consumption and approximately 9% of the world?s zircon production. With the commissioning of plants by Albian Sands and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in Alberta?s oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widelyheld suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers: 1) The bitumen coating on the sand grains; 2) Secondary mineralization such as pyrite, siderite and calcite 3) A high proportion of aluminosilicates (approximately 25%) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier. The pyrite can be removed by flotation. And the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

May 1, 2001

By Tom Setterfield

Monster Copper Resources ?Junior focused solely on IOCG deposits ?Founded by ex-WMC geoscientists ?Properties in Brazil, Wernecke Breccias (Yukon), Central Mineral Belt and Nova Scotia Nova Scotia ?JV with Wallbridge Mining Company ?Ongoing Story ?Presented as a case study in generation and implementation of IOCG exploration program

Apr 1, 2005

By Douglas Lay

Attention has been drawn in the publications of the Department of Mines to the view that veins of two different ages occur in the Cariboo district, namely, those of Jura-Cretaceous age and those of pre" Mississippian age. It has been further pointed out that while there is doubtless a wide distribution of veins of pre-Mississippian age in and about the Barkerville and Stanley areas, and in the vicinity of Round Top mountain and Yank's peak, there is no such wide distribution of veins carrying gold values of commercial significance. Veins of the latter type discovered to date occur almost exclusively within one or other of two comparatively narrow zones, both trending northwest and southeast, the one extending from Island mountain co Round Top mountain, and the other from a point somewhat north of Stanley co Yank's peak. In addition, there is some evidence of a third zone trending northwest from Spanish mountain, at or near the contact of the pre-Cambrian and Mesozoic rocks. In short, all the evidence from prospecting and lode-mining operations to date indicates that values are mainly restricted co zones having marked directional distribution. Moreover, it can be demonstrated that the placer deposits resulting from the erosion of the pre-Mississippian veins have a similar directional distribution, allowance being made for modifications due to glaciation. The observations offered in this paper are of the nature of a generalization which seeks to explain certain anomalies both in the vein-mineralization and in the -important auriferous-pyrite replacement deposits in limestone which have recently been discovered. For the sake of brevity, the Island Mountain-Round Top Mountain zone will be referred to as Zone No. 1, and the Stanley-Yank's Peak zone as Zone No. 2.

Jan 1, 1936

By Lou Covello

Bow Valley Industries Limited i conducting an on-going exploration program for gold in Archean, turbidite-hosted iron formations near the Lupin mine on Contwoyto Lake, orthwe t Territorie . Exploration philosophy and practice are modelled on the Lupin deposit where 70% of the gold occurs within laminated pyrrhotitechert. sulphide facie iron formation. Thi i intimately associated with barren to low-grade silicate facie iron formation which i enclosed by predominantly argillaceou meta ediment . This type of mineralization i amenable to exploration through an integrated program of geological and geophy ical surveying, consisting of the following: i) Geological urvey both regional and local to outline area of turbidites and a ociated iron formation. Structural and tratigraphic trends documented during this phase are useful in determining eventual grid configurations. Grids are then mapped and ampled at 1:2000 cale. ii) Magnetometer and gradiometer urvey at the ame scale define strongly magnetic diabase dyke and erratically magnetic portions of iron formation. iii) VLF-EM survey are u eful in outlining conductive trend invariably as ociated with sulphidic or graphitic phase of iron formation. iv) Geological updating and ampling of iron fom1ation based on the geophysical su rveys. This is necessary for the production of a final geologic map and a an adjunct to drill target election. In problematic instances self-potential urveys have documented the pre ence of non-conductive sulphide accumulations, and horizontal loop EM surveys have been used to determine conductor geometry and quality. Target selection is based on a synthesis of the information from all of the above surveys with the results of no single survey being critical to drill decisions. The program is designed to provide first-pass, detailed , cost-effective ground coverage of large areas of highly prospective geology.

Jan 1, 1986

By A. Gillis, J. Keyes

"This is a prelirr1inary report on automatic control at East Malartic Gold Mines.After installation of the cyclones in the East Malartic grinding circuit, the interest was aroused in the automatic control system for the circuit. Investigations were made as to the possibilities of such an installation. This resulted in a preliminary survey of the circuit by Milltronics Ltd and an analysis of the circuit by Mines Branch personnel. A study of the investigation and analysis indicated that a cost reduction and improved efficiency could be expected by the installation of an automatic control system in the grinding circuit. It was also indicated tl1at such installation should pay for itself within a year. This was the point that sold management on such installation. The need of three operators was expected to be eliminated .The installation was to consist of a central control panel, microphoncs on each mill, regulation of feed rate, pneumatic valves for addition of solt1tions, density control of the cyclone overflow, which is a grinding circuit product, rod mill feed box plugging detector and a conveyer weightometer for tonnage indication and control.As well as the elimination of one man per sl1ift, other benefits which were to be received but unable to estimate were: 1) More tonnage per clay by operation of the mills at the proper capacities. 2) Lower grinding costs. Less under-loading should result in less steel wear and lower pumping cost. In the condition of overloading, a coarser grind is obtained resulting in greater impeller and liner wear. The overloading and underloading showed up on the n1icropl1oncs. 3) An improvement in the recovery as a result of less over-load. The tailings loss from a coarser grind are not as frequent."

Jan 1, 1965

By Tim Bekhuys

Equator Principles ? Applies to projects > $10 million ? Voluntary agreement between 58+ EPFIs ? Categorized projects based on environmental risk, consequences ? Requirements for EA, EMP, use of safeguard policies, consultation ? IFC Performance Standards on Social and Environmental Sustainability ? Apply if the project is in a low or lower-middle income country ? Low-middle income countries defined by the World Bank Development Indicators Database

May 1, 2008