Search Documents

By L. Mercier, A. El-Hsaeri, L. Amaratunga

Laboratory scale studies of the development and application of high capacity heavy metal ion adsorbents with uniform nanoscale porosity (denoted MP-HMS, mercaptopropyl - hexagonal mesoporous structure) to extract gold from solutions is described. The adsorbents are selective towards gold ions. The adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 330-mg gold per gram adsorbent (up to 30% of their weight). Gold uptake by the adsorbent was found to increase dramatically with solution agitation. The adsorbent was found to be extremely effective in adsorbing gold ions from ultra- low concentrations, like those found in mine effluents. Experimental studies indicated that MP-HMS maximum adsorption of gold (99.9%) occurred under all solution concentrations. Another promising attribute of these materials is their favorable adsorption kinetics. The contact time required for 80% adsorption of gold was found to be less than 60 seconds. The efficiency of these nanoporous materials for the recovery of gold from mining effluent is evaluated and their prospect for application in the mining industry discussed. The process thus has the prospect of becoming an efficient and environmental friendly method to recover gold from aqueous solutions, such as gold mill effluents.

Jan 1, 2004

By S. Itoh, T. Nagasaka, J. Ono

With respect to the recycling of used lead-batteries, a pure lead is required to prepare a lead-calcium alloy electrode for a new maintenance-free battery. The pure lead can be obtained by means of electrolytic and/or pyrometallurgical refining. In the lead electrorefming, antimony is concentrated in anode slime. From the viewpoint of the recycling and recovery of metal values from used lead-batteries, especially from anode slime, oxidation experiments were conducted for pure liquid antimony in the temperature range between 973 and 1373 K to elucidate the oxidation kinetics and mechanism. Furthermore, since lead anode slime generally consists of antimony, lead and bismuth, experiments have been also carried out using antimony-lead-bismuth alloy. The equation relating to the mass transfer characteristics in the gas phase was then applied to analyze the oxidation kinetics. As a result, it was found that the anode slime treatment, that is, an oxidation of antimony concentrated in anode slime followed by vaporization as antimony oxide Sb406, should be operated with higher oxygen partial pressure and sufficient amount of gas flow rate at lower temperature around 1073 K. The feasibility of the oxidation treatment for anode slime has been also discussed.

Jan 1, 2004

By Par G. Jönsson, Joachim von Scheele, D. S. Sarma, Mukul Goyal

Dust from flue gas cleaning systems at iron and steel production is frequently considered as a waste problem, but it is actually a potential raw material source. By using a technology like the oxyfuel based OXYFINES technique, it can be melted into a suitable form. The product from this processing, however, needs to meet the requirements of a recyclable raw material, here particularly a top-charged blast furnace feed. The present work has been focused on characterization of the product produced from these dusts by OXYFINES technology. The investigation has been carried out on samples of processed dusts from a European integrated steel mill. It was done by means of chemical analysis, density measurement, light optical microscopy, X-ray diffraction, scanning electron microscopy combined with energy dispersive spectroscopy, and micro indention hardness measurement. Special attention was paid to the presence of zinc, an element that might be harmful while recycling the material (e.g., in a blast furnace). The results show that the product contains four different regions with different morphologies and properties in the material, which are discussed in detail. The overall conclusion is that by processing the dusts in this way, a raw material suitable for recycling in a blast furnace can be obtained.

Jan 1, 2004

By Franc R. Joubin, Donald H. James

"THE PROPERTY of Rexspar Uranium and Metals Mining Co. Limited is situated within 3 miles of Birch Island, British Columbia, a village on the C.N.R. main line 80 miles north of Kamloops. The claims extend up the south slope of the North Thompson River valley.Prospecting in the area dates back many years. Fluorite was reported in 1918, lead showings in 1926, and bog manganese in 1929. Diamond drilling in 1942-43 indicated more than a million tons of material containing 20 per cent fluorite and 15 per cent celestite in what is known as the 'fluorite zone'. Marketing and beneficiation difficulties have delayed further development of this deposit.Systematic checking of specimens and drill core by the B.C. Department of Mines and the Geological Survey of Canada revealed low radio-activity in the fluorite zone material. Subsequent prospecting with Geiger counters revealed zones of higher radioactivity a few hundred feet distant from the fluorite zone. The property at this stage came under the development direction of Technical Mine Consultants Limited, who undertook a program of diamond drilling. Of the several radioactive zones located, two have so far rewarded development and appear to constitute low-grade uranium orebodies. These are referred to as the ""Black Diamond"" or ""BD"", and the ""A"" zones -see section. Open-pit mining of the thick, dip-slope orebodies appears possible.General GeologyWalker (1) describes the local rocks as metamorphosed sediments cut by granodioritic intrusives and by greens tone. At the property the sequence is:GreenstoneUnconformity or intrusive contact Trachytic member -tuffs, breccia, flows. Argillite -black, thin, not always present. Schist -thin-bedded sericitic quartzite and siltstone with some calcareous layers."

Jan 1, 1949

By W. Dan Hausel

"Abstract-Hundreds of diamonds have been found in the United States. The majority of the discoveries occurred during the 19th century as a by-product of placer gold mining. Most of these early diamond finds have no known source, and in many cases are situated in areas unfavorable for diamond exploration based on current models that require kimberlite or lamproite to be emplaced in a stable Archean craton or Proterozoic craton margin.Diamonds have also been recovered in situ from lamproite at Murfreesburo, Arkansas, from kimberlite in the Lake Ellen region of Michigan, and in several kimberlites in the Colorado-Wyoming State Line district. Unverified reports also suggest that diamonds may have been recovered from other related intrusions at a number of localities in the United States."

Jan 1, 1995

By LeRoy A. Thorssen

The use of lightweight aggregate as a constituent of concrete is not a recent development. Pumice was used by the early Romans, in pozzolana cement concretes, in the construction of many of their works. However, the recent development of manufactured lightweight aggregates, such as the expanded shales, vermiculite and perlite, has created a possible use for a whole new group of Portland cement concretes. Concrete can now be produced with unit weights ranging from 30 to 150 pounds per cubic foot and with various insulating, fireproofing, acoustical and structural properties. The tonnage of such materials being used has increased considerably in each of the past ten years, and can be expected to increase for the next several years as availability of the aggregates becomes more widespread and the properties of such concretes become more thoroughly investigated and more generally known. LIGHTWEIGHT aggregates of many types have become avail-able to the construction industry in most localities on this continent

Jan 1, 1963

By Geoffrey C. Streeton

A continual objective of mine operations is to reduce ground control costs without compromising the overall safety or performance of the installed ground support. Any change in the ground support regime must not result in a less secure or safe workplace. The due diligence required to implement a change in rockbolting practice is extensive, particularly when the new bolting system has not been used at any other mining operation. Factors such as yield, shear strength and embedment strength must all be investigated to gain an understanding of how the rockbolt can be expected to perform. This paper also discusses the substantial cost reductions and efficiency gains which can be achieved through the introduction of the Jumbolt rockbolt.

May 1, 2001

By E. V. Manlapig, U. Erol, V. Ross, K. Tshimanga

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By W. Dan Hausel

"Hundreds of diamonds have been found in the United States. The majority of the discoveries occurred during the 19th century as a by-product of placer gold mining. Most of these early diamond finds have no known source, and in many cases are situated in areas unfavorable for diamond exploration based on current models that require kimberlite or lamproite to be emplaced in a stable Archean craton or Proterozoic craton margin.Diamonds have also been recovered in situ from lamproite at Murfreesburo, Arkansas, from kimberlite in the Lake Ellen region of Michigan, and in several kimberlites in the Colorado–Wyoming State Line district. Unverifed reports also suggest that diamonds may have been recovered from other related intrusions at a number of localities in the United States.IntroductionTo date, diamonds have been recovered in situ from kimberlite in the Colorado–Wyoming State Line district and from a kimberlite in Michigan. Additionally, diamonds have been recovered from lamproites in Arkansas. Diamonds have also been reported from kimberlite in Kansas, and from peridotite in New York and Maryland. However, these latter reports have not been verified."

Jan 1, 1995

Mining Association of Canada ! Represent base and precious metal, diamond and oil sands producers as well as nonferrous metal smelting and refining ! Member companies account for the vast majority of Canada?s mineral and metal production ! Mining is a major economic sector in Canada ! 13% of total exports ($47 billion) ! Employment near 400,000 ! 4% of GDP The Kyoto Protocol ! November 18, 2004 -- Russia deposited its instrument of ratification with the United Nations ! The Kyoto Protocol entered into force on February 16, 2005 ! The Kyoto Protocol is now an international and legally binding agreement to reduce GHG emissions world wide ! Canadian GHG target = 6 percent below 1990 ! First Commitment period 2008-2012

Apr 1, 2005

By G. E. Rodger, R. Jugoon

"SUMMARYSamples of Aunor gold precipitates which varied widely in gold content were fluxed to produce a bisilicate slag with various oxidizers and combinations of oxidizers. On the basis of some preliminary tests a flux composition was chosen which appeared to show the most promise.The different components of this flux were then incorporated into a matrix for a 23 factorial design experiment to determine what were the most important variables and what changes should be made to the flux composition to optimize the resultant total bullion fineness.The results of the 23 factorial design experiment showed that the flux composition as calculated was very close to an optimum as only very minor changes were required to give bullion in excess of 995 fine.INTRODUCTIONEarly in 1969 the results from the Aunor Gold Mines refinery showed that wide variations existed both in precipitate grade and in total bullion fineness. An analysis of this data showed that as the precipitate grade increased, the gold bullion fineness also increased (see appendix 1). Therefore, to improve the refinery results test work was initiated to: 1) improve the precipitate grade and 2) to determine, with the help of statistics, a flux composition which would be able to handle wide variations in precipitate grade and give a total bullion fineness in excess of 950 fine."

Jan 1, 1970

By Russell Spry

THE cyanide plant of the Cariboo Gold Quartz Mining Company, Limited, at Wells, B.C:, in the Barkerville section of the Cariboo mining division, was erected during the latter part of 1932 and placed in operation in January, 1933. The initial capacity of the plant was about 50 tons daily. This was increased to 100 tons at the end of 1934 and stepped-up to 150 tons in September, 1935. It is expected that further plant extensions, for milling a total of 200 tons daily, will be required during the early part of 1936. Recent additions to the mill have been so planned as to permit ready expansion to 275 tons daily when underground development warrants the milling of this tonnage. It is the purpose of this paper to outline briefly the steps taken to bring the plant to its present capacity and to comment on possibilities for further plant expansion. The gold in Cariboo Gold Quartz ore occurs as free gold in the quartz and on pyrite surfaces. Some of it is very finely divided, specks l/10,000 inch having been observed microscopically, according to Dr. G. Hanson. In addition to pyrite, which comprises probably 15 to 20 per cent of the mill feed, galena and sphalerite are present, with small amounts of arseno-pyrite and chalcopyrite. Sulphobismuthites-chiviatite, galenobismutite, cosalite, etc.-occur more or less frequently in certain sections of the mine. Following tests on Cariboo ore by the Mines Branch, Department of Mines, at Ottawa, treatment of the ore by straigh t cyanidation was recommended and a 50-ton plant employing continuous counter-current decantation was erected. This plant was built as a pilot mill, the intention being to erect a larger mill after metallurgical treatment had proved successful over an extended period. This original installation, however, has been enlarged and retained as an operating unit, additional equipment being added to it as capacity increases have been required.

Jan 1, 1936

By D. L. Johnston

"The avenues and degree of participation by aboriginals in the Canadian minerals industry have changed significantly during the thirty years of the author's career in that industry.The typical 1950s cycle of mineral industry involvement of a local non-Europeanized aboriginal was as an individual employee. The employment relationship would begin with the best of intentions by both parties of permanence and terminate when the pioneering employee was unable to reconcile the attendance behaviour required by the employer and the social-sharing behaviour demanded by family and friends.Cominco Ltd. has been a mine operator and developer in the North since the 1920s. Cominco's early experiences with employment of non-Europeanized natives at the Con Mine in Yellowknife, Northwest Territories from 1938 to 1986 was a negative experience from both the employee and employer ends. A series of classic failures in employment of individual aboriginals was a large part of the history. A few Metis or natives from other areas were the permanent aboriginal employees at Con (2010). Racial prejudice was overt on the street in Yellowknife and, it can be assumed, in the workplace, as well.The history of aboriginal employment at the Pine Point, Northwest Territories operation (1964 to 1988) was somewhat better but also frustrating. The mine was equidistant (80 km) from the Dene communities of the Hay River Indian Reserve and Fort Resolution, both on Great Slave Lake. Despite a large aboriginal presence and many well-intentioned efforts, employment of aboriginals at Pine Point never got much beyond ten per cent. These would have been half local and half northern prairie aboriginals. One continuing success story was the railcar loading and covering crew led by Ed McKay, a local aboriginal. This predominantly aboriginal crew did its own recruiting and several are on Cominco pension."

Jan 1, 1995

By R. C. Wallace

In the early explorations of the Northwest, the search for minerals played a not inconsiderable part. The first episode had its disillusioning sequel. Sir Martin Frobisher, in 1576, sailed up that bay in Baffin land now known as Frobisher bay, thinking that he had the coast of Asia on his right hand. He brought back from this expedition a piece of 'black earth' from Hall island, from which an alchemist by coaxing nature, or his own conscience, obtained gold. A second expedition of three ships was fitted out in 1577, and a third of fifteen ships in 1578. The ships were loaded with this 'black earth', which on subsequent investigation was found to be worthless, and interest in minerals for the time being ceased. In 1612 Hall and Baffin went in search of a gold mine near the Arctic circle on the west coast of Greenland, reported to be worked by the Danes. They found old workings, but no ore. To come nearer the Hudson Bay area, it is noteworthy that the charter granted by Charles II to the Hudson Bay Company in 1670, as a result of the explorations of Radisson and Groseillers, was given "-in consideration for their having at their own cost and charges undertaken an expedition to Hudson bay in the northeast parts of America, for the discovery of a new passage to the South sea, and for the finding of some trade for furs, minerals and other considerable commodities, and of their already having made by their undertakings such discoveries as did encourage them to proceed farther in pursuance of the said design, by means whereof there might probably arise great advantage to the King and his Kingdom - ".

Jan 1, 1925

By Alan Bauer

IN RECENT PAST YEARS, the mining industry has expanded rapidly and mining engineers have not been generated in sufficient numbers to sustain this growth. Canada has not been alone with this problem, which has resulted in considerable soul-searching as to what the solution might be. Because of the unfavourable economics of running small departments such as mining, metallurgy, ceramic engineering, etc., one approach in some cases has been to put these departments together to form a department of mineral science which now has a broader base structure. Another solution has been the "conversion kit" program which has been conducted both at universities and in industry. At universities, such programs have consisted of converting graduates of other engineering disciplines into mining engineers. In some of the large mining corporations, extensive training programs have been used with the same aim.

Jan 1, 1972

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

Innovation ? In economics a change must increase overall value, customer value, or producer value. ? Innovations are intended to make someone better off, and the succession of many innovations adds growth to the whole economy. ? Innovation may refer to both radical and incremental changes to either products, processes or services.

Feb 1, 2008

By A. Cadieux, J. -B. Pineault, C. Allaire

The temperature measurement of the molten metal in the aluminum transformation process is of prime importance. This is particularly the case for aluminum treatment furnaces, such as holding and melting furnaces. Such reverberatory type of furnaces involve a thermal gradient across the metal line which limits the life of conventional thermocouple protective ceramic shields, due to the action of locally induced thermal stresses. This paper presents a novel thermocouple assembly using a composite refractory protective shield allowing long term resistance to such above conditions. Example of results obtained from various tests in aluminum holding furnaces are presented. The results confirm the superiority of the novel thermocouple assembly, as compared to conventional thermocouple units.

Jan 1, 2004

By T. Cutard, H. Marzagui, E. Ouedraogo, M. Roosefid, M. Prompt, C. Deteuf

The present work is achieved in the framework of a French national program on modeling and experimental characterization of the thermo-mechanical properties of refractory materials (PROMETHEREF). This research program is aimed to establish fair models and experimental database and to make it available to industrial partners for numerical simulation of industrial structures made of these materials. The present paper focuses on two silica-alumina refractory castables, an andalusite based one and a bauxite based one. We will present the first rheological characterization results achieved at room on normal and preheated samples of these two refractory castables. Refractory castables are characterized with the help of four points bending tests, compression tests and tensile tests.

Jan 1, 2004

By A. D. Akerman, D. D. Young, G. R. Baiden

The development and maintenance of underground roadways are increasingly important aspects of the modern mining process. With the trend toward automation and track-less mining, roadbeds capable of with standing increased wheel loading have proven necessary to maintain high vehicle speed and reduced maintenance costs. Concrete has been used successfully on some roadways in order to obtain the required characteristics. However, this solution usually involves unacceptable expense. The objective of the Road Router project was to create a drift floor profiling machine capable of cutting a smooth surface out of the existing rock floor of development drifts and ramps. This surface would provide a durable, high strength, low rolling resistance roadbed that would allow for reduced operating cycle times and lower maintenance costs of scoops and haulage trucks. The Road Router has the potential to offer an alternative to concrete with substantial cost savings.

Jan 1, 1997