Search Documents

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By M. Fiset, D. Belley

"In a country with a cold climate like Canada, the cost of replacing worn parts of snowplow equipment such as blades, is enormous. A great number of these blades, with different mechanical properties, are available, but few studies have been made to facilitate their selection according to the optimum ratio of wear resistance to cost. To attain this objective, laboratory tests have been developed to correlate test results with those obtained from various road service conditions. The test materials, 1080steel in different states, 1090steel and D2 tool steel were chosen to cover a large range of hardness as well as different microstructures. Comparison of the wear resistance of the test materials relative to a standard revealed, in general, a good correlation between the results of laboratory cement wheel tests and those from the road tests. Scanning electron microscope wear scars of laboratory and road test specimens were compared to determine if similar removal material mechanisms were active. IntroductionThe correlation between wear tests in service and those performed with the aid of laboratory equipment is of considerable interest. As a matter of fact, when correlation exists, it allows one to evaluate the performance of a material more easily and at a lesser cost.Several authors have been interested in simulating various wear circumstances, especially abrasive wear. In particular, the simulation of wear on implements working the soil, has been tried by several researchers. The test using the rubber wheel seems to be the one giving the best correlation if the soil is rather sandy and its moisture content is low.However, little work has been done concerning wear on the plates, skids and blades attached to trucks used for levelling and snowplowing; such equipment being used to keep roads clear in northern countries. Now each year, companies introduce new steels by claiming that the y are superior in performance to their predecessor s and invariably they demand a higher cost. The study presented here was undertaken with the goal of making a more judicious choice of these steels by simulating their behaviour in the laboratory. Moreover, the examination of abraded surfaces in situ and in the laboratory have also allowed us to compare the respective wear mechanisms."

Jan 1, 1988

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By Douglas A. Sloan

"Recently, a number of major mining companies seemed unable to find a president from within the industry, and were searching outside the industry. From this, one could conclude that managers within the industry are either not being prepared or are not preparing themselves for presidential responsibility. Opinions were sought from a number of senior executives, to attempt to define the skills a prospective president should acquire and what actions a company could take or that a prospective president could take to acquire these skills.This paper contains summaries of the opinions obtained, along with the author's comments. The paper also describes the actions some companies are taking and the actions that an aspiring president can take to prepare himself for corporate management.IntroductionA manager is promoted up the management ladder when the manager's superiors believe that he is capable of handling a more senior position. Normally, the manager acquires this credibility by outstanding performance in his current management post, whether it be in a junior management (supervisory) or in a vice-presidential capacity.In most instances, the skills required for promotion can be acquired in the current position or, at worst, the abilities exhibited in a candidate's current role will convince his superiors that the necessary expertise for the more senior position can be acquired on-the-job. This is particularly the case when the new skills are felt to be an extrapolation of the old skills.However, in the case of appointment to presidential rank, there appears to be a need for new expertise which often is not acquired in normal management progression or, at least, boards of directors of some mining companies seem to believe this to be the case. The objective of this paper is to attempt to define the new skills that should be acquired by a manager who aspires to be the president, and to describe what actions might be taken by him to acquire them."

Jan 1, 1982

Some examples of the results of research projects, conducted in the KOMAG Institute of Mining Technology are presented. Special attention is paid to mining machines and equipment, and improving work safety and comfort of miners in underground workings. From numerous scientific and technical achievements of the KOMAG Institute within the last 2 years, a few design solutions have been selected for a presentation. Some results of European projects on innovative solutions are described as well, highlighting KOMAG?s role in the national and international research area.

Aug 1, 2013

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada's current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today's commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By Ted J. Smith, Stephen E. Kesler

"Zonation patterns are welt developed in the mafic metavolcanic rocks that host epigenetic quartz-carbonate-gold vein mineralization at the Hollinger-McIntyre deposit. Carbonate alteration assemblages are strongly zoned about mineralization. Proceeding inward from background greenschist facies rocks to alteration envelopes enclosing individual veins, the following assemblages are observed:Assemblage I-quartz-albite-chlorite-epidote-actinolite-(calcite)Assemblage II-quartz-albite-chlorite-calcite-epidoteAssemblage III-quartz-ankerite-sericite-(chlorite-calcite)Assemblage IV-quartz-albite-ankerite-sericiteLithogeochemical zoning is equally well developed as variations in whole-rock abundances ofAs, Au, Ba, Rb, and Sb. As and Ba form the most useful zonation patterns, outlining individual ore zones as well as broader trends of mineralization.Gas chromatographic analyses of fluid inclusions in the quartz-carbonate veins indicate that the mineralizing fluid was an H20-C02 mixture. Locally, CH4-rich fluid inclusions are associated with graphitic and/or carbonaceous wallrocks. Fluid inclusions in ore-bearing veins have higher CO2 contents than those in non-ore veins. Extensive sampling and analyses of veins from the area surrounding the deposit reveals a well developed zonation of CO2 contents about the main zone of mineralization. Low CO2 levels (1-2 mole%) in veins are peripheral to the deposit and increase to over 12 mole% in mineralized zones.The observed zoning of the carbonate alteration assemblages is a result of the addition of CO2 to the wallrock, which is consistent with the zoning of CO2 in the fluid inclusions.The zoning patterns delineated in this study are useful in exploration both on a deposit scale and on the scale of individual ore zones."

Jan 1, 1985

By M. A. EI Zeky, A. E. El-Nikbaily, M. A. Shahin

"Possible mechanisms of microsilica dust formation and factors affecting its quantity have been discussed. General mathematical models to predict the dust quantity based on electrical and coke consumptions, and flue gas temperature as functions of silicon recovery in the process and silicon content of the alloy have been established. It has also been shown that the flue gas temperature can be used as an additional process control parameter. Comments are made on the effect of the dust formation on the whole process economics and it is pointed out that the formed microsilica dust is a valuable by-product and not an industrial waste. INTRODUCTIONFerrosilicon is produced in electric arc furnaces with submerged electrodes. The charge mixture consist s mainly of quartzite, coke as the reducing agent and iron chips. The products are ferro silicon and carbon monoxide, various other volatile materials, water vapour and silicon monoxide gas. Carbon monoxide and silicon monoxide oxidize at the charge surface when mixed with air entering through the furnace hood openings. The off-gas contains a considerable amount of dust, which is mainly very fine particles of silica formed as a result of oxidation. The emission of dust containing gases to the atmosphere causes serious pollution problems to the environment. Therefore, the control of the formation of the dust, preventing it from escaping to the atmosphere, and dealing with this very fine dust collected from the flue gases represent important technological and economical parameters in the ferrosilicon production industry.This paper is concerned with the relations between the quantity of formed micro silica dust, as a function of both silicon recovery and silicon content in the alloy, and various other technological parameters; and their possible effects on the energy consumption and economics of the whole process."

Jan 1, 1989

By C. Diaz, S. W. Marcuson, K. I. Burgess

Deep roasting in fluid bed roasters is the first unit operation in Inco&apos;s "roast-reduction smelting" process for the treatment of nickel sulphide concentrates. The roaster product, a low sulphur calcine, is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte which is then converted to low (<1%) iron matte in Peirce-Smith converters. Due to the deep roasting, a minimal amount of sulphur dioxide is evolved in the smelting and converting stages. Sulphur is eliminated from the concentrate almost exclusively in the roasters in a single, continuous, strong, gas stream suitable for treatment in an acid plant. This paper discusses the commercial scale testing of deep fluid bed roasting of nickel concentrate at Inco&apos;s Thompson Smelter as part of two commercial scale campaigns on roast reduction smelting conducted in 1981-1982. Slurry feeding, practised during the second campaign, permitted excellent control of the air/concentrate ratio in the roaster and, in turn, good control of sulphur elimination (about 80% of input). Smooth autogenous operation with high oxygen efficiencies (about 95%) was promoted by operating at bed temperatures of830°C to 850°C with calcine recycle. High throughputs and the desired metallurgy were achieved. The extensive testwork conducted during the two experimental RRS campaigns demonstrated thot deep fluid bed roasting of nickel concentrate at high oxygen efficiency is a technically viable operation.

Jan 1, 1994

By E. I. Vargha-Butler

The determination of surface tensions and contact angles of coal particles is of great interest for coal beneficiation processes such as froth flotation and oil agglomeration and for the inclusion of coal particles into oil droplets as a means of enriching the fuel. Methods for contact-angle measurements on small irregularly shaped solid particles have not been available in the past. Therefore, we recently developed a novel technique to determine contact angles and surf ace tensions of coal particles. Two types of bituminous and one type of subbituminous coal particles have been tested. The technique used is called the freezing-front technique and it considers the behaviour of the test particles (in the range of 20-250 pm) at the solidification front of carefully selected, well-defined solidifying melts (matrix materials) such as thymol, biphenyl, naphthalene, salol and 2-phenyl phenol.The results show that the technique works well, providing quantitative and detailed information on the wettability of coal particles. The sensitivity of the method is so high that a difference in contact angle of approximately 4 degrees between the smaller and the larger particles is clearly registered.

Dec 1, 1981

By M. Maldonado, P. Olivares

"A submersible sensor for real-time gas holdup measurement in the collection zone of industrial flotation machines is introduced. The working principle is based on the generation and measurement of a pulp flow using a gas-exclusion cell immersed in the aerated slurry. The gas exclusion cell consists of a variable-area open vertical tube designed to be filled only with pulp by preventing gas bubbles entrance. The higher density of the fluid column within the cell generates a downward flow of pulp; the rate of this flow is proportional to the gas holdup outside the cell. The gas holdup measurement is achieved by tracking the velocity of the pulp flow leaving the gas-exclusion cell, using a magnetic flowmeter. Construction details of a prototype and its testing in two- and three-phases are discussed.INTRODUCTIONFlotation process optimization consists of finding and maintaining operating conditions that maximize flotation performance measured in terms of recovery and grade. The selective separation of mineral particles proceeds in two interactive zones where different and simultaneous phenomena take place: in the collection zone, the valuable particles are separated by collection on the surface of bubbles, while in the froth zone, the bubble-particle aggregates are gathered, drained to remove entrained particles, and taken into the concentrate stream. The cell overall performance, which can be determined from proper stream sampling, is a function of the recoveries in the individual zones. These zone recoveries cannot be independently measured nor calculated from operating variables. Progress in the assessment of these recoveries has been slow because on-line and reliable sensors to measure properties of the drastically different dispersions existing in both zones are not available.In the case of the collection zone, it has been demonstrated that the recovery of hydrophobic particles on the surface of bubbles, considered as a process with first-order kinetics, correlates with the bubble surface area flux (Finch et al., 2000; Hernandez, et al., 2003; Lopez-Saucedo et al., 2012). Bubble surface area flux (bubble area generated per unit time and cell cross-sectional area), is a variable affected by gas flow rate, bubble size distribution, and frother type and concentration. Gas holdup (volumetric fraction of gas dispersed in the slurry) is also affected by the same variables, and as such, carries information on the interacting variables that define the performance of the process. Therefore, a correlation between gas holdup and bubble surface area flux was expected and demonstrated (Finch et al, 2000), and since gas holdup is easier to measure as no bubble size is required, it has the potential to be the basis of a cell control and optimization strategy if a continuous sensor is available."

Jan 1, 2016

By Don McColman

"Tires, although not always the largest single cost item in open-pit mining operations, will place in the top three, along with explosives and fuel. How this high-cost supply is controlled is dependent upon on an efficient tire program. The success of this program is, in turn, dependent upon the people who are directly associated with tires and their use, namely: the mine&apos;s tire personnel, the tire sales representatives and a technician for the rubber company. The technician will relay his observations and information received from the mine personnel back to the manufacturer with recommendations to overcome current problems .Haulage truck tire life and costs in a hard rock open-pit mine are governed and controlled by four important factors:I) Field control.2) Operating within manufacturer&apos;s guidelines.3) Different tire purchasing methods.4) Scrap piles.Field ControlPerhaps the most influential people involved in this program are those who live with the tire through every hour of its lifespan: the truck driver, the shovel operator, the dozer operator, the grader operator and the shift boss. Of these, the truck driver has the most control, in that he can drive over or around rock s as these situations arise. The loading area, the edge of the haul road and the dump account for most of the tire injuries.This is why shovel, dozer and grader operators must appreciate their influence on haulage tire life. Spillage cleanup must be ongoing and is not being done adequately if any of these operators are idle. The shift boss that drives by a rock on the road without removing it or calling for a cleanup has little recourse with the truck driver who runs over it-he has sanctioned the driver&apos;s actions by his own neglect."

Jan 1, 1986

By E. Wright

"INTRODUCTIONThe Ruttan Mine is located twenty-two km east of Leaf Rapids in northwestern Manitoba. The copper-zinc exhalative massive sulphide deposit is comprised of a series of individual and interconnected en echelon lenses which strike east 20 degrees north and dip south 70 degrees. The mine has been owned and operated by the Hudson Bay Mining & Smelting Company since July 1987. Sherritt Gordon Mines Limited began mining the orebody in 1973 from an open pit, but production has been entirely from underground since 1980. HistoryDuring the progression from open pit to underground mining, it was recognized that manual methods of ore reserve calculation were inadequate for responding to changing metal prices and evaluating alternative mine plans. The mine planning system that was developed is described in the paper, ""Computerization of Ore Reserves and Mine Planning Functions at Ruttan Mine"", presented by B.C.W. Haystead at the 1984CIM Annual General Meeting. At that time, programs for core logging, diamond drill hole plotting, grade interpolation, ore outline digitizing, and reporting had been developed by the Systems Department for use on Sherritt&apos;s UNIVAC 1100 mainframe computer. Telecommunications linked terminals at the Ruttan coreshack and office to the UNIVAC in Fort Saskatchewan, Alberta. The same mine planning system was also used at a second property.Operation of the mine planning system was expensive, and it was evident that increased use required a costly upgrading of the UNIVAC in order to maintain an acceptable service level to all users. The system was re-evaluated,&apos; and it was concluded that: core logging was not easily adaptable to a new property, nor flexible enough for exploration; plotting, grade interpolation, and digitizing required considerable manual effort; and that the UNIVAC operating system was difficult to learn.It was recommended that a study should determine if: core logging could be redesigned and/or implemented on a microcomputer; interactive graphics be used to reduce the effort for functions requiring visual interpretation; and the creation of input processors would assist users in setting up parameters for guiding the programs."

Jan 1, 1989

By J. B. Evans

"NORMALLY the duties of the exploration engineer and geologist cover the initial, and possibly, the most important phase of mining property evaluation; that phase being the presentation of an opinion of the property's ore reserve potential in terms of tonnage and grade. The prime objective of this pa-per is to outline one method of bridging the wide gap that lies between a know ledge of a property' s tonnage and grade potential and an appreciation of the value of that property in dollars and cents.THE PRESENTATION OF PROPERTY EVALUATIONThe engineer engaged on a mining property evaluation, regardless of whether he be an independent consultant, or a company employee, has as his goal, the presentation of his appreciation of the property's potential value or worth within terms of reference acceptable to his principal.To furnish a complete evaluation report, the evaluator must firstly study all aspects pertaining to the particular property under consideration, then present his appreciation of the property's worth in some tangible form. The ultimate presentation is one giving a Present Value of the pro pert y in terms of monetary exchange. Such an idealistic presentation is not always possible; typical preventives being -insufficient reliable information, limited time, Jack of ability and absence of definite direction."

Jan 1, 1960

By Ji Wang

Reflective in-seam wave detection has the advantages of a far detection range and wide applicability. It has been successfully used in detection of many abnormal geological structures in work-faces, such as faults and collapse columns. However, a reflective in-seam wave is a dispersion wave. It has weak energy and is always covered by the direct in-seam wave. In the past, underground seismic explorations were not able to image the opposite roadway using reflective in-seam waves. To solve this problem, we propose a new method of reflective in-seam wave imaging based on adaptive dispersion filtering. This method processes the reflective in-seam wave using a filter with the parameter of transmission distance. The degree of similarity of the filtered and the explosion signal is used to estimate the transmission distance and image the reflective objects. We test and verify this method using real underground seismic data. This research is helpful for the detection of coal mine goafs and abandoned roadways in work-faces or in front of tunneling ends.

Aug 1, 2013

By Bern Klein, A. Tugba Cebeci, Libin Tong

"Sensor based sorting faces two main challenges related to limited capacity/throughput and the ability of sensors to accurately discriminate based on estimated grades. This paper is aimed at improving sensor discrimination. Sensors have the ability to measure more than a single response. X-ray fluorescence (XRF) can detect and provide concentration information about a range of elements. Similarly, electromagnetic sensors (EMs) can generate magnetic susceptibility and conductivity responses over a range of frequency levels. The sensors thereby provide a response signature rather than a simply a single response that is a proxy for a metal grade. Furthermore, integrating sensor responses can improve the discrimination of metal bearing rock from waste. A study was conducted on a gold ore to assess sortability using XRF and EM sensors. A multi-variable regression approach was used to develop models that included a range of responses. Correlations improved significantly when compared to single response correlations. The approach showed that both positive and negative correlations contributed to the improved correlations. Stepwise regression simplified the models and showed that 2nd order interaction effects can be important. The approach also showed that combining different responses can improve discrimination accuracy. An important outcome of the study was that an ore that had been consider not to be sortable was determined to be sortable through the application of an approach that used the sensor responses in a more intelligent manner.INTRODUCTIONMining is aimed at recovering valuable minerals from their host rocks. Many methods are used to recover valuable minerals, and finding efficient and cost-effective ways is the key in research and production. . Ore sorting technology is fitting this definition. It not only discards waste rocks away from the concentrator but also recovers metal bearing ore particles that could be lost to the waste dump. The benefits of ore sorting include increased energy efficiency and reduced water and reagent usage in the downstream operations (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013)."

Jan 1, 2016

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments.A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including reasonable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects."

Jan 1, 1990

By I. Filzwieser, S. Konetschnik, A. Filzwieser, A. Anzinger

Production in copper electrorefining tankhouses mainly depend on two factors: The deposition area, which is a result of the amount of installed cells and cathodes, as well as the current density - the amperage per square meter of deposition area. The present paper shows, that the most economical way of achieving a certain production is to maximize current density by using the METTOP-BRX-Technology - as building and infrastructure can be kept more compact. This industrial proven technology applies a parallel electrolyte flow in each electrolysis cell. In 2011, the first fully industrial applications started up: At the secondary smelter Montanwerke Brixlegg AG, 156 cells are equipped with the METTOP-BRX-Technology; this allows a current density of 390 A/m². Xiangguang Copper Co., Ltd. - a primary smelter and refinery - operates its new tankhouse (720 cells) at 420 A/m²; this stands for an production increase of 50% compared to the same sized ISA tankhouse which is limited to 280 A/m². The first part of the present paper gives a cost comparison between a conventional copper electrorefining tankhouse and a high current density tankhouse when assuming a Greenfield project. The second part describes the cost savings when installing the METTOP-BRXTechnology in an already operating tankhouse.

Jan 1, 2014

By Feng Tianran, Lu Shijie, Shen Zhengchang, Han Zhibin, Tan Ming

"As a kind of non-metallic material, high-purify quartz sand has been widely used in many fields. Flotation is a popular way to process quartz sand. But it is in difficult position for flotation to get high-purify quartz product due to large amount of coarse particles contained in the feed. In this paper, a design principle of special flotation cell for high-purify quartz sand has been put forward base on ore property analysis and laboratory test, and the pilot scale special flotation cell has been developed to meet the requirement of the quartz sand flotation process. The special flotation cell for high-purify quartz sand is featured by middle positioned impeller, false bottom and draft tube, which could decrease the rising distance of mineralized bubble and strengthen the circulation capacity of the lower part of the flotation cell. Hydrodynamic study indicates that high air dispersion degree and strong lower slurry circulation could be produced by pilot scale special flotation cell, which is helpful to create a suitable hydrodynamic environment for quartz sand processing.INTRODUCTIONNatural quartz is a non-metallic mineral, which is widely used as raw material in multiple industry process (Shifu, 2006). High purity quartz, especially containing more than 99.9% silicon dioxide, is characterized by high temperature resistance, small thermal expansion coefficient, highly insulating and so on. The demand of high purity quartz has been rising along with social and economic development, now high purity quartz is widely used in the field of photovoltaic industry, electronic information, communications and aerospace industry.Quartz is a kind of main rocking-forming minerals in the nature. There are seven genetic types, such as natural crystal, quartz sandstone, quartzite, vein quartz, konilite, natural siliceous sand, granite quartz (Baolei, Shuilin, & Dianchao, 2012). The natural crystal is primarily used as raw material to refine high purity quartz, but it is not available for two reasons. On the one hand, the natural crystal is extremely expensive and poor in resources reserves, which can not satisfy the need of large-scale industrial production. On the other hand, the chemical component of natural crystal is instability, it may lead to low stable product performance in large industrial applications, and it is also difficult to achieve raw materials standardization. Therefore, there are a lot of studies to search for other technological methods to obtain high purity quartz from other genetic quartz types."

Jan 1, 2016