Search Documents

1. Scope of project In South Australia, the Western Mining Corporation operates the underground copper and uranium mine Olympic Dam. The deposits concerned are enormous (approx. 570 million tons) and have been mined since 1988. At the end of 1996, Western Mining decided to increase the capacity of Olympic Dam from 85,000 t.p.a. to 200,000 t.p.a. Planning At this point, SIEMAG-GHH Mining Division was asked to carry out a study including the planning of the entire shaft hoisting operations and calculation of the investment and operating costs involved. With the assistance of Australian partners, the study was completed within a single month. The principal points of the study were as follows: ? Planning of the hoisting machinery for 1,375 tons per hour from the surge bin below ground to the discharge bunker above ground. ? Optimisation of the hoisting operation with regard to maximum availability and safety. ? Optimisation of the time schedule to minimise the financing costs of the investment. ? Statement of the investment and operating costs. ? Comparison of the technical data, design and availability of the planned machinery with reference plants. Construction of the plant Following acceptance of the study, the decision was taken within a few weeks to implement it. SIEMAG Transplan GmbH received the order to execute the entire shaft hoisting machinery on the basis of the study submitted. The decisive factors in placing the order were: ? Convincing study, adherence to schedule ? Reference to comparable plants elsewhere ? Reference with regard to availability.

May 1, 2003

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014

By Gabka T., R. E. Gregorczyk

Work to improve employees' behavior in Głogów Copper Smelter began in 2009. It has been noted that over 90% of accidents at work are attributable to human reasons. At that time, a series of external workshops was contracted based on exercises conducted by a psychologist trainer with supervisors. Having trained about 300 employees, an observation of employee behavior at workstations was started as part of the control of risk reduction measures. As a result of the above actions, the number of accidents was reduced by half between 2009 and 2017. Currently, internal workshops for communication improvement for behavioral auditors are conducted by the employees of the Smelter. Named: "I observe, react and communicate" and aimed at further mastering the elements of the safety culture in Głogów Copper Smelter. INTRODUCTION KGHM Polska Miedz is an integrated mining and smelting copper producer based in Poland and operates on the international metal market. KGHM, with annual production of over 500 thousand tonnes of copper, holds a middle position in the world ranking of copper producers. At the same time, in Europe it is the largest producer of copper from its own ore deposits, possessing its own integrated production structure, from underground mining operations to final, top-quality product. It is also worth mentioning that KGHM Polska Miedź is one of the largest Polish exporters and, apart from copper, is a significant primary silver producer in the world. The mission of our company, consistent with its strategy, is to produce copper and silver in a safe mode for workers and the environment, with reduced environmental impact. Therefore, "Głogów" Copper Smelter operations are continuously focused on the creation of safe working conditions, and minimizing the negative effects on the environment. The company meets the requirements of an Integrated Management System comprised of the following: Quality Management System ISO 9001:2008 Environment Management System ISO 14001:2004 OHS Management System according to the requirements of BS OHSAS 18001:2007 Being a proud socially responsible company, we are aware that part of an efficient OHS system is to recognize, monitor, prevent, educate and motivate, thus continuously improve working conditions for 2500 employees of Głogów Copper Smelter &Refinery. We clearly communicate that a low accident rate is beneficial for both, staff and the company, and is of utmost importance as a part of our health policy.

Jan 1, 2019

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By Jim Wickens, Andy Cole, John Pekrul

"The roaster facility at Barrick Goldstrike Mine treats double-refractory sulfidic/carbonaceous gold ore. Prior to oxidation in the roasters, the ore is ground in two parallel dry grinding circuits utilizing 19’ Ø x 75’ double rotator mills. The design plant throughput was 12,000 dstpd. However, process improvements have significantly increased throughput rates by 25-50%. The current daily throughput record is 20,078 dstpd. Grinding circuit improvements contributing to this success include feed size reduction, ball size optimization, automatic ball charging optimization, and operating strategy changes. In addition to the changes already made, this paper discusses future optimization initiatives including on-stream particle size analysis and “real-time” ore hardness determination techniques.INTRODUCTIONBarrick Goldstrike Mines is located 29 miles Northeast of Carlin, Nevada, USA. Through 2001, the property has produced over 23 million ounces of gold making it one of the premier gold operations in the world.Prior to Barrick’s ownership, the property began producing gold from a small heap leach operation in 1975. The small-scale heap leach production continued through 1986, and in January 1987, Barrick acquired the property. Increased exploration activity by Barrick significantly increased gold reserves. In August 1988, a 4,500 dstpd mill facility was commissioned to treat high grade oxide ore. Also, heap leach operations had significantly expanded. In 1990, the mill was expanded to 6,000 dstpd, and the first autoclave was commissioned to treat refractory sulfide ore. By the end of 1996, the mill and pressure oxidation facility had expanded to 16,000 dstpd and heap leaching had ceased as oxide reserves were exhausted. In 2000, a roaster facility was commissioned to treat double-refractory sulfidic/carbonaceous ore."

Jan 1, 2003

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By D. M. Doyle, P. J. Hannon

"The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) is a subsidiary of a five-year Economic and Regional Development Agreement, signed on June 11, 1984. The objectives of the M.D.A. are to strengthen and diversify the Nova Scotian mineral industry and to coordinate federal and provincial policies and programs. The agreement outlines the activities and responsibilities of each government, including the division of the cost (60:40, federal: provincial) between governments. The agreement established a framework for joint planning to avoid overlap or duplication of programs.The M.D.A. programs are broadly divided into five sectors (Table 1 and Fig. 1): Geoscience, Minerals Technology, Development, Firm Specific and Public Information. Each sector is administered by a subcommittee composed of one federal member and one provincial member. The subcommittees report to a Management Committee. The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) Management Committee is made up of Dr. Jack Reeves from EMR and Dr. Richard Potter from the NSDME.The Geoscience subcommittee, co-chaired by Peter Giles (NSDME) and William Poole (EMR), manages the regional geologic, geochemical and geophysical studies in the province. Included in this sector are studies into mineral deposits and the basic geological relationships between mineral deposits.The Mineral Technology sector is co-chaired by the authors, Don Doyle (CANMET) and Pat Hannon (NSDME). This sector of the M.D.A. conducts studies into mineral processing, sampling, deposit byproduct commodities and project feasibility analysis."

Jan 1, 1987

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By Y. Bai, J. J. Liu, D. Q. Li, S. Z. Liu, X. T. Wang

"This paper presents the results of an industrial test using 8 t/d of Baotou concentrate (50% REO) of a clean metallurgical process, which includes: 1. Roasting with H2SO4 at low temperature (220~260 0C) in a batch roasting furnace followed by water leaching to obtain a leach liquor as feed with a yield of >95% RE and Th, recovering F as fluoride, producing a leach residue amounting to 1/3 of an equivalent high temperature residue and containing <0.03% Th and radioactivity < 3×104 Bq/kg compared to the normal high temperature residue containing 0.2-0.3% Th and 1×105 Bq/kg. 2. Separating Th with N1923 and extracting RE by P507 has been completed in mixer-settlers. Test results indicate that the ThO2 product has a purity of > 95% with a yield of 99%, and the RE has a yield of >95%, in which ThO2/REO <5×10-6, and that P507 loaded RE connect straight with separating RE using P507-HCl system. 3. Treatment and multipurpose use of "three wastes" (water, gas and solids) are discussed in some detail."

Jan 1, 2014

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

"More efficient drilling and blasting techniques have shown measurable improvements in throughput at the Barrick Goldstrike wet grinding mill.A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas participated closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of improving throughput in future years, despite the projected harder ores. Plant studies were conducted to determine if adjustments to drilling and blasting could positively influence throughput. At the Goldstrike mill the greatest opportunity from the D2M initiative is realized on the hardest ore. Grinding throughput for softer ore, <15 kWh/st, can meet or exceed the downstream pressure oxidation requirements. Grinding throughput for harder ore, >15 kWh/st, is limited by the SAG milling capacity. Better fragmentation in the D2M ore, as demonstrated by image analysis, increased throughput 5% to 10% (25 to 50 stph) compared to the standard mining methods.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of:1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots.2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy.3) Improved distribution of the explosives by decreasing pattern spacing.INTRODUCTIONThe Barrick Goldstrike Open-Pit group, along with the Process division, began experimenting with novel blasting technology and techniques to improve mill throughput in the spring of 2001. A series of tests were developed to determine if fragmentation and ultimately mill throughput could be influenced by optimizing the drilling and blasting program in known"

Jan 1, 2004

By S. Mostaghel, S. Nicol, M. Y. Solar

Once upon a time, the process engineer developing the design criteria for a new saprolite ferronickel smelter had it easy: most ores were around 2.5% Ni, with a Fe/Ni ratio of 4 to 5 and a SiO2/MgO ratio of about 1.6; to use the French word: garnierites. The ferronickel grade selected was the conventional 20 to 25% Ni and the impurity levels could be predicted from well established [C], [Cr] and [Si] vs (FeO) graphs. However the process engineer can no longer depend on statistics to design smelters: Ni grades are decreasing while the goethite contents are increasing; SiO2/MgO ratios vary from 1 to 3; and Al2O3 concentrations are reaching levels that cannot be ignored. Mechanistic models must be developed to select or predict essential parameters such as kiln and furnace reductions, ferronickel grade, slag losses, metal and slag liquidus, operating temperatures, etc. But these models must be simplified so that they can be used on a routine basis; and they must be calibrated against a wide range of commercial operations in order to yield the most realistic predictions possible. The present paper proposes one possible approach, using FactSage as a basic source of thermodynamic data. The predictions thus obtained are compared to actual performance for two well documented operations, as well as to the predictions made with other tools that might be more accessible.

Jan 1, 2014

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By C. Edwards

ABSTRACT The versatility and specificity of rare earth elements (REEs) have led to their use in an everincreasing variety of applications in new technologies; consequently, demand for REEs has increased significantly. However, separating REEs safely and effectively is a complex and expensive process. This paper presents a review of REE mineral processing technologies, providing an update on current capabilities in REE mineral processing and REE extraction from the major commercially valuable REEbearing minerals such as bastnaesite, monazite, and xenotime, as well as the ion-absorption type of REE deposits.

Jan 1, 2013

By Ingrid Hann

The Triple Bottom Line ? Economic Sustainability ? Creation of Joint Venture companies ? Planned evaluation of other kimberlites ? Social Sustainability ? Impact Benefit Agreement and Participation Agreements ? Education and training initiatives ? Environmental Sustainability ? Environmental management ? Mine closure planning

May 1, 2008

By A. A. Paoli

The selection of a mining plant for carrying on development work presents many problems distinct in themselves, and affected by various local factors. In this paper, the writer proposes outlining and discussing in some detail the chief factors governing the economic selection of such plants. This will be followed by an enumeration of the underground and surface plant required for carrying on several hypothetical exploratory and mining operations. Where it is impossible or not convenient to obtain hydro-electric power, and where wood for fuel is scarce, we now find oil engines being used. A 100 h.p. oil engine, such as would be required to operate a three-drill air compressor, consumes approximately five Imperial gallons of fuel-oil per hour at full load. On the basis of a 60 per cent load factor, this gives, for eight hours&apos; operation, a probable actual consumption of twenty-four Imperial gallons.

Jan 1, 1929

By M. Mirnezami, D. Lascelles, J. A. Finch, E. El-Ammouri

"In a previous publication, the depressant action of Mg above pH 10 on Cu-activated sphalerite was described (Lascelles et al., 2001). In the present communication, a second role, aggregation is introduced.Aggregation (i.e., the tendency of particles to cluster) is measured using settling rate and turbidity converted to an aggregation index (AI) where 0 corresponds to dispersed and 1 to aggregated. Surveys of Cu and Zn flotation stages at four concentrators showed the A1 increased significantly above pH 9. The metal ions identified in the process waters, principally Ca and Mg, were tested to determine which might be responsible. The presence of Mg was found to be the most important, 50 ppm Mg having a greater impact than 500 ppm Ca fkom pH 9 to 1 1. In one plant, poor repeatability in A1 was suspected to be related to varying Mg levels; doping with Mg significantly increased AI.In both aggregation and depression, therefore, the common feature is the impact of Mg at pH > 9. Over this pH range Mg forms a range of hydroxy species, including Mg(OH)2 precipitates. Suggested aggregation and depression mechanisms associated with these precipitates are introduced. Possible problems and opportunities arising from the findings are discussed.INTRODUCTIONProcess waters in flotation circuits contain a variety of metal ions that may introduce unwanted activation or depression. Two common metal ions are calcium and magnesium. Typical concentrations are in the range 50 ppm Mg and 500 ppm Ca (Marticorena et al., 1994, Basilio et al., 1996, Negeri et al., 1997, Nesset et al., 1998)."

Jan 1, 2002

By Laurence McGonagle

"The Highland Uranium Project (HUP) is located approximately sixty miles northeast of Casper, Wyoming and is owned and operated by Power Resources, Inc. (PRI). With an annual production of680 tonnes (1.5 million lbs) U308, HUP is one of the largest uranium producers by in-situ leach (ISL) in the western world. Uranium is currently produced from four wellfields with a total flow rate of approximately 1,135 m3/hr (5,000 gpm). The carbonate leach solutions are processed by anion ion exchange at two satellite facilities located in close proximity to the wellfields. The loaded resin is transported by truck to a central processing facility for elution of the uranium. Uranium in the pregnant eluant is precipitated and washed prior to calcining.Wastewater from the satellite facilities is treated and used for irrigation at a Land Application Facility. The wastewater generated at the central processing facility is injected into a 2,750 m (9,000 ft) deep waste disposal well.When economical mining of the orebodies is complete, restoration of the groundwater is initiated. There are currently two wellfields at HUP undergoing ground water restoration. Phase I restoration consists of removal of the carbonate leach solution from the ore body. Phase II includes treating the withdrawn fluid with reverse osmosis and reinjection of the permeate into perimeter wells.Future plans include construction of additional satellite facilities at the Gas Hills Project and other economical deposits located within 240 km (150 mi) of HUP. The capacity of the central processing facility will be increased to 1,815 tonnes (4 million lbs) U308 per year by late 1999."

Jan 1, 1998