Search Documents

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, R. Pérez-Garibay, C. Jimenez-Velasco

A current problem in gold production is the presence of copper minerals which dissolve during conventional cyanidation practice. The dissolved copper causes several problems in the different stages of the process. This issue is the base for copper elimination/recovery methods such as the Sulphidization, Acidification, Recycling, and Thickening (SART) process, which is currently used in gold production plants around the world. Even though the process is well established, new challenges appear as the composition of the solution varies from ore to ore, in some circumstances affecting the performance of the SART process. This work presents a thermodynamic study and experimental tests performed to understand the role of the initial copper concentration and sulfur addition, on the efficiency of the copper removal. For a constant cyanide concentration, an increase in the initial copper concentration causes a decrease in copper removal; high sulfur/copper molar ratios favor copper removal. We demonstrated that the cuprous sulfide formed from solutions with high ionic strength, presents better sedimentation rates than solutions with less ionic strength. For solutions with low sedimentation rates, the use of some pretreatment is necessary to facilitate the sedimentation such as addition of flocculants, particle recirculation and the used ultrasonic pretreatment.

Jan 1, 2014

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By Friedrich Benthaus

"The natural and man-made realities on either side of the Atlantic are different. Therefore, a large part of the other side' s knowledge and experience cannot be transferred easily. In the following, the author will attempt to describe some of those developments in the German hard coal industry which may be of particular interest to readers on this side of the Atlantic.The area of the Federal Republic is quite small, especially if compared with a country as large as Canada. On a territory the size of the maritime provinces of New Brunswick and Nova Scotia, Germany holds coal reserves roughly corresponding to the total Canadian reserves. More than 20 billion tons of hard coal down to a depth of 1500 m, and more than 30 billion ton s of brown coal of lignite are technically and economically extractable acording to current technology.However, not only are Germany's coal resources more concentrated; the country is also densely populated, and there are dense networks of railroads and highways All components of the so-called infra-structure are available everywhere, be it electricity, any machinery or personnel. Public opinion is likely in favour of an increased utilization of coal.The coal industry is well developed through a long evolution covering centuries. As a consequence, there is an effective and intensive cooperation of numerous bodies and institutions concerned with coal mining, from government agencies including the inspectorate to suppliers, trade union s, producing companies, to jointly operated management and research organizations. In the Federal Republic, hard coal is mined in deep mines only, and lignite in general, only from open-cast pits. There is a complete organizational and geographic separation of hard and brown coal in Germany. Because the Federal Republic holds only insignificant mineral oil and very little natural gas deposits, coal is essentially the only and consequently the most valuable source of energy."

Jan 1, 1984

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

The quality of refractory bricks and castables could be determined by direct measurements of their material properties such as elastic properties, porosity, density, etc. using conventional static or non-destructive testing (NDT) dynamic techniques. Quality monitoring of refractory linings is much more challenging and complicated. The static methods require undesirable drilling and sample extractions from the furnace structure. A more desirable alternative is the use of NDT techniques for material quality estimation. The Acousto Ultrasonic-Echo (AU-E) technique is a new stress wave propagation approach for monitoring the quality of refractory linings in operating furnaces. In this paper, the conceptual methodology for the AU-E technique is described, the capabilities and limitations are expanded, and the results from two case studies are discussed.

Jan 1, 2005

By Fadi Layyous Gedeon, David Hatton, Solomon Mogashoa, Tuhin Banerjee, Faisal Aljohani

The adoption of innovative technologies in mineral processing often raises concerns about complexity and integration. However, Woodgrove’s Direct Flotation Reactor (DFR) technology at Barrick’s Jabal Sayid copper concentrator provides a different perspective. This paper outlines the smooth integration of DFR technology from piloting to full-scale commissioning, showcasing how easily the cells were brought online. Installed in a cleaner scalper role, DFR cells at Jabal Sayid upgrade re-ground rougher concentrate to final concentrate in one stage. Despite processing challenging ore, the DFR cells delivered concentrate grades that consistently exceeded expectations. The commissioning process was straightforward with minimal hurdles, highlighting the technology's user-friendly nature. This paper advocates for a shift in perceptions about new technologies in mineral processing. The success of DFR technology at Jabal Sayid demonstrates that “different” doesn’t mean “difficult.” By focusing on ease of commissioning and operational integration, innovative solutions can enhance processes, improving efficiency and productivity in the mining industry.

May 4, 2025

By W. J. Stickney

"Over-all recovery of cadmium has been increased at the plants of the Hudson Bay Mining and Smelting Co., Limited, since the construction of a slag fuming plant and baghouse where smelter flue dust is recovered. This pa-per outlines the distribution of the cadmium in plant products from the concentrator to the refining department.The leaching of cadmium-bearing precipitates from the zinc plant is also discussed. This consists of a two-stage leach; first with sulphuric acid and then with copper sulphate. Details of the leaches are outlined along with the safety measures practised in handling the hydrogen and arsine evolved.The paper describes the final preparation of electrolyte for the refining cells by purification for copper and thallium. Deposition of cadmium, using a polyacrylamide as an addition agent, is discussed.An outline is given of the melting procedures, under either sodium hydroxide or zinc chloride, and of the sub-sequent treatment of the dross to recover entrained cadmium and thallium."

Jan 1, 1966

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By Lionel C. Kilburn

"This geological engineering method is based on jour main characteristics of mineral properties, viz; location: inclusion of valuable mineralization; inclusion of geophysical and/or geochemical targets; and inclusion of geological targets. These are subdivided into a total of 19 subcategories, which are used to determine the value of the property.The nineteen subcategories are prioritized and assigned relative value factors from 1.3 to 10. Value of each mineral claim unit is determined by applying the appropriate subcategory factors to a base value of $400per 16.2 hectare unit. Property value is calculated by totalling the values of such individual claim-units.The boundary between ore grade and sub-ore grade must be estimated for each property under valuation, thereby making the method sensitive to mineral commodity prices.A clear and disciplined sequence of decisions based on personal experience forms the basis of this method. The method utilizes all factors normally used to value a mineral property.IntroductionIt is generally accepted in the exploration industry that valuation of exploration properties is a subjective rather than objective process (Roscoe, 1986; Lawrence, 1988; Lawrence, 1989; Woodcock, 1985), and that it is greatly influenced by the experience and qualifications of the person who is doing the valuation. However, the significantly low degree of objectivity in mineral property valuation at this point in time invites effort to achieve a more quantitative engineering basis.Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand , and political-economic conditions, all of which vary with time. Therefore, any valuation is valid for only that point in time when it is made. Mineral deposits can decrease as well as increase in technical value with time."

Jan 1, 1990

By Per-Lennart Nystedt

"The Boliden Lead Kaldo Plant for the treatment of lead bearing flue-dust from the Copper Smelter and the Slag Fuming Plant has been in operation at the Ronnskar Works of Boliden Metall since the middle of 1976. At the present stage, the plant can treat lead-bearing dust of different kinds and compositions. The process allows good separation of arsenic and halogens from lead.The flue dust from the Copper Smelter and the Slag Fuming Plant is very complex and, apart from lead, also contains zinc, copper, tin, bismuth, cadmium, antimony, arsenic, sulphur, silver, chlorine and fluorine. The metallurgical process has been developed by Boliden Metall and has been tested on a pilot scale at the Foundation for Metallurgical Research (MEFOS) in Lulea, Sweden.The pelletized dust is smelted in the converter, where the heat is generated by an oil oxygen burner. The second step consists of reduction with coke. A lead bullion and slag are obtained. The slag, transported in liquid form, is treated in the Slag Fuming Plant for the recovery of zinc. The third step is the elimination of arsenic from the bullion. This is achieved by treating the lead with iron (turnings or pellets). The result is a crude lead and speiss. The lead contains silver, tin, antimony and bismuth, and is suitable for the final refining stages in normal plant equipment for refined lead.For process control, we use the rapid analysis centre, which is pneumatically and electronically linked to 'all major plant sections and allows for a quick turn-around between delivery of the sample and feedback of results. All three steps in the process are performed in the same converter.Since the starting up of the plant, the original process has been subjected to some modifications. Initial problems related to equipment, maintenance and environment have been solved step by step. Examples are quoted. Recent operating particulars are presented."

Jan 1, 1980

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Ahmed Mohamed Elmahdy, Hidekazu Matsuoka, Kyushu University, Tsuyoshi Hirajima

"Selective flotation of chalcopyrite and molybdenite was studied using various surface treatment methods such as electrolysis, ozone treatment, and plasma. Oxidation via electrolysis method indicated that only chalcopyrite surface is affected by electrolysis due to conductivity difference with molybdenite. Oxidation treatments and XPS analyses indicated that chalcopyrite became hydrophilic due to deposition of oxidized iron on its surface. Various oxidizing methods also showed that chalcopyrite was selectively oxidized and this can apply selective flotation of chalcopyrite and molybdenite. The possible mechanisms are proposed in this work based on surface analyses and thermodynamic calculations.INTRODUCTIONCopper sulphide minerals often associate molybdenite (MoS2) which is one of the most important by-products (Wills, 2006). It is important to recover molybdenite perfectly not only since molybdenite is valuable mineral, but also contamination of molybdenite into copper concentrate or contamination of copper mineral into molybdenite concentrate indicates penalty for both concentrate values (Wills, 2006). Conventional separation of copper sulphide and molybdenite has been achieved with sulphide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulphide. However, this current process shows imperfect molybdenite recovery and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant. Hirajima et al., (2014) have been studied selective flotation of molybdenite and chalcopyrite (CuFeS2), which is the most important copper mineral, with plasma pre-treatment. They reported that plasma pre-treatment process followed by washing treatment can improve molybdenite floatability and depress chalcopyrite. This result is attributed to surface oxidation and selective conversion of chalcopyrite and molybdenite wettability. It may be hypothesized that another surface oxidation methods could give a similar result as plasma treatment process. To test this hypothesis, in this study, as comprehensive study of oxidation effect, various oxidation methods such as electrolysis, ozone, and plasma were investigated. Electrochemical measurements, thermodynamic calculations to predict the chemical reactions happened during the process, various surface analyses, and flotation experiments were carried out."

Jan 1, 2016

By S. C. Tadolini

"Roof bolts are the primary means of roof support in underground mines in the United States. Presently, post installation loads are measured on about 10% of the expansion anchor and combination bolts by using standard torque wrenches that Unit the accuracy of the measurements to about ±30%. No system has been available for measuring the loads generated on full-column resin grouted bolts. Mine roof bolts are long, slender, non-uniformly sized, roughly forged, and placed in a corrosive environment, creating obstacles for researchers trying to utilize ultrasonic reflection techniques to measure strain. A complete measurement system has now been developed by the U.S. Bureau of Mines, Denver Research Center. This system is being used successfully in determining loads measured on expansion anchor and combination bolting systems, examining the transfer mechanics of full-column, resin-grouted bolts, and measuring loads generated on bolts in an underground roadway support system.IntroductionMillions of roof bolts are used each year to provide structural support in underground U.S. metal, non-metal, and coal mines. Approximately 45% of the bolts used are expansion anchor, 45% are resin-assisted combination or full-column resin-grouted, and 10% are friction anchored. The effectiveness of these bolting types is dependent on a number of factors including rock density, bolt length, in situ stresses, rock properties, bolt pattern, installation tension, etc. When implementing expansion anchor and resin assisted combination bolts , installation and post-installation tension, or load, is a major determinant of support quality and subsequent behaviour of the reinforced roof. The method by which these systems carry roof loads is well understood and documented(1,2).The importance of these installation and long-term bolt tension measurements is well recognized and are required in the federal government regulations(3). A statistical sample of the bolts, lout of 4 during installation and lout of 10 inby the last open crosscut, is required to be measured using current torque wrench technology. The disadvantages of this system are the disturbance and weakening of the anchorage and limitations of accuracy to approximately ± 30%. The method by which resin-grouted bolting systems carry roof loads is much less understood, mainly because testing procedures used to evaluate point-anchor systems are not effective on resin-grouted bolts.Due to these problems, the U.S. Bureau of Mines designed a measurement technique that provided a highly accurate, low cost-per- bolt system that led to the development of ultrasonic pulse echo instrumentation. The original system was designed to measure the tension only on expansion anchor bolts. Recent developments and system modifications have permitted measurements on resin-assisted and full-column resin-grouted bolts. The use of these types of support systems has been increasing steadily in underground coal mines.The development of this instrumentation has provided laboratory and field results that help to explain the mechanics and relationships between the applied loads and the interaction between the grouted bolt system consisting of the bolt tendon, grout, and rock."

Jan 1, 1990

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By Michael S. Moats, Alex Luyima, Tomas Oliveira

Some commercial copper electrowinning facilities use Cyquest N-900 (a polyacrylamide) or HydroStar (a modified polysaccharide) to improve the density and smoothness of copper electrodeposits. However, the effects of these additives have not been studied extensively in the open literature. Thus, the electrodeposition of copper at 40 oC from a non-stirred synthetic electrowinning electrolyte (40 g/L Cu2+, 160 g/L H2SO4, and 20 mg/L Cl-) in the presence of various concentrations of either additive was evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). CV results show that neither additive has much effect on the nucleation overpotential of copper electrodeposition on stainless steel. However, Cyquest N-900 polarized the copper deposition reaction upon the return sweep. The EIS data indicates that Cyquest N-900 increases the reaction’s charge transfer resistance and creates a second low frequency loop. HydroStar had minimal effect on the electrochemical data generated by CV or EIS. Thus, the mechanism by which HydroStar affects the copper deposition reaction still needs to be determined.

Jan 1, 2014

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By R. W. Boyle, W. Dyck

"Scientists throughout the world have observed radioactive disequilibrium in the uranium decay series. Radiometric and fluorometric determinations of U in plants from the Goldfields district and in sediments and rocks from the Beaverlodge district exhibit marked radioactive disequilibrium. The eU/U ratio in plants rooted in mineralized ground shifts from greater than unity to less than unity for those rooted in background soils. A similar shift is observed in the transition from rocks to stream sediments and to lake sediments in the Beaverlodge district.Results of a Rn-Ra-U survey of lake bottoms in the Key Lake district show that anomalous hydromorphic U from U mineralization is parallelled by anomalous Rn, even though there is much less Ra in the lake-bottom sediments than one would expect from the amount of U present. IntroductionDisequilibrium in the U decay series has been studied for many years and is observed in almost all surficial environments. Rosholt (1959) measured U, 234Pa, 23O'fh, 226Ra, 222Rn, and 210Pb in a large number of U ores and outlined six types of situations to explain disequilibrium. Davy (1974) outlines the geological significance of radioactive disequilibrium situations with respect to exploration. Levinson and Coetzee (1978) discuss possible mechanisms by which separations of parent and daughter elements are affected and suggest analytical pitfalls that may be encountered in the use of radiometric techniques when disequilibrium has occurred. Generally, it is the oxyphile and easily complexed parent 238U (with its associated isotopes 235 U and 234U) that is leached from rocks and soils at a faster rate than are the daughters, 230Th, 226Ra, 2loPb, and 206Pb. This mobilized U is adsorbed on sediments in streams and lakes, or enters groundwaters, where it is eventually precipitated under reducing conditions, occasionally in oregrade concentrations. This surface leaching and"

Jan 1, 1980

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By E. Poiate, P. A. L. P. Firme, D. Roehl, M. A. Carrion, A. M. Costa

Drilling high-pressure/high-temperature wells in salt rock formations is still a challenge for the energy industry. Creep and solubility is part of the salt rock physical-chemical behaviour, which must be considered in the design of the wells. The stress redistribution caused by drilling, in addition to thermallyactivated processes, triggers creep deformation, leading to borehole closure and the imposition of loads on the casing. The drilling fluid is designed by computer modeling in order to control the creep strain rate to a limit which allows the drilling operations and the casing setting. Depending upon the composition of the drilling fluid, chemical reactions on the salt wall may occur, especially in case of water-based fluids in highly soluble salt rocks. In those cases, cavities by dissolution (washouts) can be generated and the casing column remains uncovered by the cementation and laterally unconfined along the cavity length. This scenario is propitious to the loss of integrity of the casing due to phenomena such as plastic collapse, buckling and non-uniform loading on the casing provoked by the closure of salt formation around it. The casing should remain intact during the wellbore life-time. In this work, a section of a typical well crossing salt formation composed by halite and carnallite is considered. An idealized-cylindrical washout cavity inside a highly soluble salt layer is assumed. The purpose here is to evaluate the effect of the dimensions of the cavity on the integrity of the casing. Several typical diameters and lengths of the cavity are adopted. Numerical analyses are carried out with an in-house finite-element system composed by the pre-processor MTOOL 3D®, the simulator ANVEC 3D® and the post-processor POS 3D®. Salt rocks are modeled as visco-elastic materials. Creep is simulated by the Double Mechanism Creep Law, widely employed in Brazilian salt rock mechanics research. Cement and casing (steel) are modeled as elasto-plastic materials described by the Mohr-Coulomb and the von Mises criteria, respectively. Casing integrity is evaluated with respect to vertical and horizontal displacements. Vertical displacements imposed to the casing can provoke the failure of the column by plastic collapse or by buckling. Besides that, horizontal displacements of salt due to creep closure shall lead to the undesirable contact with the casing. Failure envelopes based on displacements are generated. The results of the simulations have shown that the casing failure by plastic collapse occurs preferentially in short columns, as well as buckling occurs in long and slender columns. The occurrence of both failure modes is more frequent in large-diameter cavities. Additionally, failure caused by contact between salt and casing occurs preferentially in short-diameter cavities.

Jan 1, 2015

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005