Search Documents

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

By Mohan R. Srivastava

- OUTLINE - apologies and explanations - a quick bit of history - the wisdom of Wikipedia - ?Matheronian geostatistics continued to convert Bre-X?s bogus grades and Busang?s barren rock into a massive phantom gold resource?? - variogram analysis for Busang - would variogram analysis (or variance analysis) have revealed the fraud? - what went right, what went wrong

May 1, 2007

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By R. L. Veenstra

This paper explores the connection between the stresses observed and the failure mechanisms present in the modelled cemented paste backfill. In order to look at this connection, the authors have used a previously developed model to conduct a sensitivity analysis of the model?s strength and permeability input parameters. The results from the sensitivity analysis were then compared to determine what causes modelled stresses and failure mechanisms to vary. Increased insight into the behaviour of the modelled paste will help clarify how paste behaves in the field.

Aug 1, 2013

By L. M. Amaratunga, G. G. Hein, D. N. Yaschyshyn

Fine tailings produced in the milling process have traditionally been disposed of in tailings ponds. Attempts have been made to use these fine tailings in backfill, however, to date the majority of backfill operations have utilized only a small percentage of fines. The remaining fines are, therefore, being sent to tailings ponds creating a waste disposal and environmental problem. This disposal practice is even more acute in the gold milling industry where fine grinding, required for value liberation, results in the production of large quantities of fine tailings, of which a large percentage cannot be used in backfill. Through Cold-Bond Tailings Agglomeration (CBTA), these fine tailings can be agglomerated into pellets which can then be used as a coarse aggregate in back-fill. This paper presents the results of using these pellets to create an Agglomerated Tailings Paste Fill (ATPF) made entirely of fine gold mill tailings and cementing binders. Through this process, supplementary imported aggregates such as sand, gravel, rock-chips are not required while still maintaining adequate back fill strength. By using this CBTA technology, fine tailings are diverted from tailings ponds and becomes utilized as a value added resource in the form of aggregates for use in paste fill.

Jan 1, 1997

By V. C. Wittchen, T. R. Yu, J. E. Croxall

"The consolidated rockfill at Kidd Creek Mines is a weakly cemented, minus 15 cm aggregate which posed problems for conventional drill/blast drifting methods. Consequently, lateral access to mineable ore adjacent to backfilled areas was gained by drifting around the fill in shattered rock.In mid-1987, Kidd Creek Mines began to investigate means of mechanically excavating drifts in backfill . The results of this investigation led to a trial program using a Dosco MK-2A Roadheader to excavate the required drifts in backfill.The roadheader was tested at Kidd Creek Mines from July to November 1988, in 28-735 X /C to be used as the top access for drilling and blasting 32-74/ ST. During this period, the roadheader excavated 54 m of a 4.3 m by 3. 7 m arched drift in backfill. Cutting rates over the period averaged 0.8 m/cutting hour as projected with a daily high of 2.0 m/cutting hour.Wood-lagged 2-piece steel arches on 1.2 m centres were chosen as ground support for the trial. Shotcrete will be tested in a roadheader drive for its potential to improve productivity by replacing the steel arches.The trial program included evaluations of point-attack picks, two sizes of cutter motor, 20 MPa (3000 psi) water-assisted cutting, cuttings-removal systems, and environmental control devices."

Jan 1, 1990

By T. Guan, G. Fu, X. Zhou, L. Deng

"Currently, tailings water is required to be recycled in minerals processing plants. When the flotation tailings water of complex copper-sulfur-tungsten polymetallic ore is reused to the flotation of copper-sulfur ore, a portion of tungsten would be lost in copper concentrate or sulfur concentrate due to the addition of the collectors used for oxidized ore which are also effective for the sulfide minerals in the process of tungsten flotation. At the same time, the technical index of copper concentrate and sulfur concentrate would be seriously affected by tailings water. Our experimental researches of many years show that the copper concentrate with a grade of 18.36% Cu at a recovery of 76.67% is obtained for the raw ore containing 0.60% Cu, 18.99% S, 0.16% WO3 in small locked cycle test using recycled water, through simple pretreatment of the tailings water from tungsten flotation and adding special regulator CW and new tungsten collector TM. The result is close to the performance without using tailings water. And, in the continuous pilot experiment which was continuously conducted for 4 days with the same technology, the following results was obtained: the copper concentrate with a grade of 21.74% Cu, the recovery was 71.55%; the sulfur concentrate with a grade of 45.16% S, the recovery was 80.10%; the tungsten concentrate with a grade of 42.63% WO3, the recovery was 54.62% relative to raw ore (the recovery relative to scheelite was 76.47%). The throughput of the continuous pilot experiment is 1.0~1.2 t/d, and the raw ore contains 0.56% Cu, 18.80% S, 0.14% WO3 on average.INTRODUCTIONMining industry is one of the most important developing fields, it supplies raw materials for industrial production as well as discharges much waste water. Tailings water is the main source of beneficiation waste water, it would result in severe environmental pollution if discharged directly. Generally, the tailings water would bring undesirable effect on flotation index after simple pretreatment by lime (Kalin, Fyson, & Wheeler, 2006). On the other hand, the treatment of tailings water through ion-exchange (Cui & Liu, 2015) before recycling is of high cost. Generally, in the flotation of Cu-S-W polymetallic ore, when the tailings water from tungsten flotation is treated simply by lime and recycled to the flotation of sulfide minerals, the flotation index of sulfide minerals decreases, and a portion of oxide mineral would be lost in the sulfide concentrate. As a result, the recycle rate of this kind of tailings water is relatively low, some of the tailings water is discharged after simple treatment and then environmental pollution is caused subsequently. One of the effective ways to improve beneficiation performance and increase the recycle rate of tailings water is to conduct research on developing recycle technology for flotation tailings water of complex copper-sulfur-tungsten polymetallic ore."

Jan 1, 2016

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By R. S. McCaffrey

In addition to its importance in agricultural production, Wisconsin is a very large manufacturing state and its rank in the metal working industries is probably first among the States of the Union per unit of population. The University of Wisconsin is a state supported institution and the Wisconsin tradition has always emphasized the relation of the University to the state and its responsibility to exercise its leader-ship where it might, in any and every way, for the development and benefit of the state and the community. The Department of Metallurgy of the University realized its responsibilities in the carrying out of the co-operative tradition and, two' years ago, an experiment was started in co-operative research between the University and certain of the industrial plants of the state. At the present time this work has so far progressed that it is no longer an experiment, and its results prove that this co-operative research may be carried on very advantageously and that, under the conditions existing in the state, the method employed has been satisfactory.

Jan 1, 1926

By T. V. Lord

Minerals containing uranium have been successfully pre-concentrated by flotation at Queen's University, Kingston. In particular, uraninite, uranothorite, euxenite, and fergusonite, have responded to flotation to yield grades of 0.2 to 6.0 .per cent U .o. with recoveries of 85 to 98 per cent, from heads analysing approximately 0.10 per cent U3Os. Of the ten or so radioactive samples examined to date, two distinct groups were recognizable, firstly, those samples in which uranium was the sole constituent of economic interest, and, secondly, those in which Columbium (with minor amount of tantalum) was present in addition to uranium. For the purpose of this paper, the results of investigation on two samples of each of the above groups have been selected as typical.

Jan 1, 1945

By Mi, Dong Liang, Jingyuan Bai, Victor Zhou, Xujun

Squirrel cage induction motors are the mostly used motors at present. Currently, the rotors of the squirrel cage induction motors are produced by aluminum die casting technique with the advantages of low cost of rotors. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size. Considering the huge quantity of motors, the die casting process is the best solution to produce copper rotor with economic cost. Because of the characteristics of copper, it is difficult to produce copper rotors by casting similar to that done in aluminum rotors. In order to improve the die casting quality of copper rotor, a new tooling structure was developed and the casting process of copper rotor was simulated and analyzed by Any-casting software. The filling process, solidification process, inner gas distribution and residual melt modulus were analyzed. It was found that the design of symmetrical runner and inner runner on both sides was helpful to reduce the impact of molten copper to the cavity surface during the filling process. The use of Slag traps array can reduce die casting defects inside the end rings. That will be helpful to improve the rotor quality. INTRODUCTION Squirrel-cage AC induction motors are most widely used in the world. In 2017, the total installed capacity of AC motors in China has reached more than 1.2 billion kW, and the annual power consumption accounts for about 60% of the total national electricity consumption. To improve the efficiency of squirrel-cage motor will be helpful to energy conservation and environment protection. There are several ways to improve efficiency of induction motors, using copper rotor is one of the most effective solutions. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size.

Jan 1, 2019

By S. S. Yuan, Q. Z. Zhu, J. F. Shao

"This paper aims at enriching a homogenization-based anisotropic damage model for hard rocks under complex loading. A new damage criterion is proposed to capture material strain softening. Within the framework of irreversible thermodynamics, we are particularly concerned with two strongly coupled dissipative mechanisms: frictional sliding and damage by microcracking, which usually take place at cracks within cohesive geomaterials under compression. Focusing on the representative elementary volume containing multiple crack families, the free enthalpy of the matrix-cracks system is obtained. Importantly, a back-stress term is involved in the local stress applied to microcracks. This back stress plays the hardening/softening role in the friction criterion which is formulated at local scale. Strain hardening owns to the accumulation of frictional shearing and dilatancy while strain softening is caused by crack growth. The multiscale damage model is used to simulate laboratory tests on the Westerly granite under true triaxial compressions. INTRODUCTIONWhen subjected to compressive loads, hard rocks present nonlinear mechanical behaviors and induced material anisotropies. In that process, two main dissipative mechanisms have been largely identified: damage by crack growth and frictional sliding along closed crack faces, which are usually strongly coupled to each other on crack scale. Theoretical investigations have shown that the damagefriction coupling analyses allow explaining a large number of experimental phenomena involved in brittle or quasi-brittle materials. Concerning constitutive modeling, the standard Eshelby’s solution-based homogenization procedure for heterogeneous materials was recently applied successfully to describing the mechanical and poromechanical behaviors of cracked frictional solids."

Jan 1, 2015

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

Due to always getting stricter environmental legislations as well as increasing land filling fees the efforts for treating residues from metallurgy are continuously increasing. In case of filter dusts from metallurgical industry, the high zinc bearing electric arc furnace (EAF) dusts or also dusts from secondary copper industry are important sources for the recovery of secondary zinc oxide. Because of low capacities for secondary zinc concentrates (like Waelz oxide) in primary zinc metallurgy, the upgrade of such concentrates to a quality that meets the requirements of high quality (technical) zinc oxide becomes more and more important. This would open the opportunity to break into new markets and use it for example directly in electrolytic galvanizing. Therefore this paper will summarize possibilities for an elimination of halogens from secondary zinc oxides. Furthermore selective volatilization trials, with a synthetic mixture according to the analysis of Waelz oxide, were carried out to remove impurities to achieve an upgraded product quality.

Jan 1, 2011

By S. Kashani Nejad, M. Bellino, K. Collins, C. Tovee, J. Godwin

Motivated by safety considerations, logistical issues, transportation cost savings, product diversification, and marketing preferences, several uranium producers are revisiting their business models and supply chain configuration and, instead of selling dried yellowcake to downstream refineries, they are moving to build in-house calcining facilities. Drying and calcining plants are relatively low-cost facilities to build and operate. The execution period of a typical yellowcake drying and calcining project is also relatively short and alternative construction methodologies, such as modularized solutions, are available. The drying and calcining technologies used for yellowcake are relatively mature, environmentally contained, and well supported by qualified vendors. The drying and calcining circuits also seamlessly integrate with upstream and downstream operations. These either produce a dried yellowcake or calcined U3O8 which are notably safer and easier to transport and market. This paper presents an overview of the recommended technology and project development considerations for yellowcake drying and calcining facilities.

Jan 1, 2020

By Jie Deng, Wenliang Xiong, Binyan Chen

"With falling rare earth metal prices, low cost beneficiation of rare earth minerals is essential. The “Flotation-Agglomeration-Magnetic” (FAM) separation process is a newly developed technology by IMUMR to economically recover rare earth elements from different types of deposits. The theory of FAM process is to selectively agglomerate rare earth particles and separate from gangue minerals by bubble flotation process. The flotation product is further upgraded by magnetic separation. The FAM process has been successfully applied in industrial production on the Dalucao rare earth ore, Sichuan, China. The average REO grade of rare earth concentrate is 65% in the latest 12 month production run, with an average recovery of 55%.INTRODUCTIONRare earth elements (REEs) include fifteen lanthanide elements coupled with two chemically similar elements (yttrium and scandium). These elements are split into two sub-groups, La to Sm are classified as light rare earth elements (LREEs) and the remaining elements including yttrium are heavy rare earth elements (HREEs) (Kumari & Panda, 2015). The demand of rare earth elements surged in recent years due to their increasing usage in diverse industrial aspects including high strength magnets, phosphors, clean energy, polishing compounds and catalysts (Goley &Scott, 2014).More than 250 REE-bearing minerals have been discovered, but many minerals are with very low concentrations of REEs, varying from 10-300 ppm (Adam &Ping, 2013). The most common rare earth minerals mined are bastnaesite, monazite, xenotime and ion-adoption REE (Chelgani & Rudolph, 2015; Kanazawa & Kamitani, 2006). Before the 1960s, most rare earth resources were extracted from monazite in the beach placer, with the exploiting of Mountain Pass in the United States and Bayan Obo mine in China, bastnaesite became the chief mineral source of rare earth resources (Klinger, 2015). These minerals are commonly separated with gangue minerals by froth flotation, gravity concentration, magnetic separation, or any combination thereof based on their specific physical characteristics (Zhou & Wang, 2014; Adam & Richard, 2014; Yang & Satur, 2015; Xia & Brian, 2015a,b)."

Jan 1, 2016

By P. A. Peach, W. H. Gross

The modern economic geologist in Canada is well equipped to apply geological, geochemical or geophysical techniques in the exploration for ore. Recently, great advances have been made in geophysics and geochemistry, and a large number of new orebodies have been discovered by these methods. An attempt is made in this paper to show that there has also been a considerable advancement in geological knowledge and that the most effective application of geophysics and geochemistry often occurs in areas already considered geologically favourable for the occurrence of ore. Ali exploration methods sooner or later suffer from diminishing returns. Therefore, as time goes on, one can expect to see the application of some of the more subtle or refined geological techniques that are presently being developed.

Jan 1, 1967

By Michael McClintock, Bern Klein

"The high pressure grinding roll (HPGR) is a relatively new comminution technology that is gaining popularity for providing energy efficient solution to hard rock mining operations. A significant barrier to increased adoption of HPGRs is the present requirement for large amounts (excess of 2 tonnes) of sample for pilot testing, which may not be possible for most early stage projects. Three methodologies have been developed at NBK Institute of Mining Engineering at the University of British Columbia that may be used for sizing design optimization of HPGR circuits. All three methodologies use a MTS pistonpress to simulate HPGR comminution. These tests are capable of providing information regarding energy consumption, energy breakage relationship, reduction ratio, and product size distributions. In a period of slow economic development, these methodologies are critical to allow the industry to cost effectively understand the operational benefits of HPGR implementation. This paper examines previous test work done at UBC, as well as the development of an HPGR and piston press database for use in sizing and budgeting of HPGR circuits.INTRODUCTIONCurrently, the mining industry faces several challenges due to falling commodity prices and escalating costs. This has applied pressure for operations and projects to reduce costs and improve project economics. In addition engineering and metallurgical budgets have shrunk as companies try to conserve cash. Improvements and optimization of milling and comminution circuits is one area project economics may be significantly improved. By considering alternative comminution technologies such as the high pressure grinding roll (HPGR), energy operating costs may be greatly lowered. Many have begun to implement HPGR crushing as an alternative to semi-autogenous grinding (SAG) mills, including KGHM and, Sierra Gorda, and Freeport Mc-MoRan’s Cerro Verde operation. However, implementing new technology for companies with little or no HPGR experience may not be practical. An operator must consider both feasibility and economics of a circuit. Currently, consideration of the HPGR requires expensive pilot scale testing for which large sample sizes are needed. In addition, few laboratories are equipped for running pilot scale HPGR test programs. Furthermore, the results of pilot HPGR testing are dependent on the quality of the sample, which cannot represent variations across a deposit. In contrast, ball mills and SAG mills can be sized using the Bond Mill Work Indexes that require a small amount of sample which enable a number of different geological blocks to be tested to allow engineers to have a complete understanding of how the comminution circuit will perform for the life of mine."

Jan 1, 2016

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By Derrin A. Auerswald, Jacolien P. Wyethe, Nanne M. \/egter

Base and precious metal refineries often produce effluent solution and slurry streams containing between 50 mg/L and several grams per liter of base metals. Metals have historically been precipitated from these streams with lime to produce effluent streams at pH values between 8 and 9. This effluent treatment process generally does not remove alkali and alkali-earth metals or halides efficiently and with more stringent environmental legislation, more sophisticated effluent treatment plants must be considered which could for example incorporate sulphate removal with ultra-filtration, or the SavminTM process, followed by reverse osmosis for the removal of halides. The flowrates of effluents are often high and if base metals can be recovered before neutralization, the revenue generated from this stream can reduce the cost to produce clean water significantly, and in the case where high concentrations are disposed of, result in a profitable operation. As an add-on to an existing the plant the recovered metal is upgraded and recycled to the plant, but the production of a saleable metal can also be considered. Technology selection for metal recovery depends on the composition and flowrate of the effluent, but could incorporate resin-in¬pulp or other ion-exchange technology; precipitation as sulphides, hydroxides or carbonates; or solvent extraction. This paper describes, as a case study, the technology selection process and uses data from Zincor. Zincor is a division of Exxaro Base Metals (Pty) Limited, a subsidiary of Exxaro Resources Limited.

Jan 1, 2011

By Shin-Kun Ryi

The world nowadays faces many challenges associated with excessive utilization of fossil, fuels, such as poor air quality and greenhouse gas emissions. Hydrogen appears to be an attractive alternative to the conventional, fossil, fuels with better energy efficiency and less environmental, impact. Pd and Pd-based alloy are the most often used membranes for hydrogen separation due to their superiority over other membranes. However, the stability of the commonly-used thin Pd-based composite membranes at high temperatures still, remains a big challenge. In this presentation, we will, report our progress on thin Pd-Ru alloy composite membrane by electroless plating high temperature applications.

Jan 1, 2010