Search Documents

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

By A. Lemay, G. Morin, C. Desmeules

"Incorporated in 1976, Sidbec Normines was mandated to exploit a deposit of specular hematite at Fire Lake. A combined effort of three companies, Sidbec, which holds 50. 1 % of the actions, British Steel Corporation another 41.67 % and finally Quebec Cartier Mining, a subsiduary of U.S. Steel Corporation, with still another 8.23 %.The deposit is located 60 miles north of the town of Gagnon. The extracted ore is crushed, in a giratory crusher, to-8 11 chunks, and from there, it is transported, by rail, to a concentrator at Lac Jeannine.A concentrate containing 65.5 % Fe and 5.5 % Sio2 is produced, using conventional methods like autogeneous mil ls and spirals. The concentrate is then transported by rail to the Port Cartier installations.The installations in Port Cartier include a secondary concentrator, a pellet plant, and stockpiling facilities for pellets and concentrate. The pellet plant has two product lines in paralel, producing a total designed tonnage of 6 millions tons of iron ore pellets, of which 3mi11ions tons are used in direct reduction furnaces.The secondary concentrator is designed to remove a portion of the silica contained in the ore, usually less than 2 % Si02 should remain from the original 5.5 % Si02 in order to produce iron ore pellets which are well suited for use in direct reduction and electric furnaces."

Jan 1, 1981

By A. K. Debnath

Mining being a site specific activity, land becomes the prime requirement for starting, successful execution and closure of any mining project. Many important mining projects are not progressing satisfactorily just because land is not easily available or environmental/social issues are not addressed properly. This is especially true in the case of open-pit mining, which requires large areas for mining, dumping of waste and additional land for other mine facilities. Mine closure & post mining land use exercises, though funded generously, may not achieve their objectives owing to uneven land profile after mineral extraction is over. One of the prominent solutions to these issues is application of steep angle conveyors in large open pit mines that will result in more space for internal waste dumping and enhanced slope stability of the dump. Additionally, such applications will result in economic extraction of mineral in deep open pits. Land reclamation exercise may start concurrently during early years of mine development as mineral evacuation is limited to a specific part of the mine. Surface mining facilities can also be advanced along with the pit by using modular/portable structures. The paper presented here attempts to address specific land related issues by developing suitable schemes and plans that can be practically implemented in open pit mines using advanced technology i.e. steep angle conveyors.

Aug 1, 2013

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By L Thompson, R C. West, T S. Kho

In 1978, the Outotec direct to blister flash (DBF) smelting process was commercialized with the commissioning of the Glogow 2 smelting facility in Poland. Since then four further DBF facilities have been constructed, two at Olympic Dam, one in Zambia and most recently one at Glogow 1 in Poland. The DBF smelting process differs considerably from conventional smelting process in both chemistry and unit operations, presenting opportunities for flowsheet capital and operating cost savings particularly when the concentrate copper grade is high. WorleyParsons has amassed considerable expertise in the Direct to Blister process and in this paper the process is compared to the modern two stage Double Flash process. The processes are modeled, and the key operating parameters, consumables and production metrics are directly compared. Subsequent flowsheets, key equipment lists and capital costs are also presented for comparison and discussion. The results show the range of concentrates which are most economically treated by the DBF process relative to those best treated in conventional processes along with those concentrates which could be treated by either process. INTRODUCTION The Outotec Direct to Blister (DBF) process was developed and installed at Glogow in 1978 (Czernecki et al., 2006). Currently there are a total of five DBFs built on three sites: Glogow No.2, Olympic Dam No.1, Olympic Dam No.2, KCM Zambia and Glogow No.1, being the most recently constructed. The DBF process was the first flash furnace process to produce blister copper and paved the way for the subsequent development of the flash converter and other continuous converting processes. Today four flash converters are in operation taking the total number of flash furnaces producing blister copper to eight. In all DBF operations it is the unique ore and concentrate composition which made selection of the DBF process the most attractive. In all cases, the concentrate is relatively high in copper but low in iron because chalcopyrite is not the major constituent. When considering smelting options for high copper, low iron concentrates a key question is then often asked, “At what point does it become economic to switch from two stage smelting and converting process to the DBF process?”

Jan 1, 2019

By T. C. WEBB

In New Brunswick, significant potash deposits are intimately associated with rocks of the Lower Carboniferous Windsor Group. To date, two deposits high in sylvinite, up to 20 m thick, have been confirmed at depths between 490 and 1,035 m below surface near Plumweseep and Salt Springs. These areas are currently under development by the Potash Company of America and the Denison-Potacan Potash Company respectively. A third area, near Lower Millstream, is also known to contain potash-bearing evaporites and is now being explored by BP Exploration Canada Ltd. All three areas are situated in the western half of the Moncion Subbasin and are within 25 km of Sussex. Numerous similarities in stratigraphy, thickness, mineralogy and structure suggest that deposition of evaporites throughout much of southern New Brunswick was contemporaneous and extended over a considerable area. Future opportunities for potash exploration in the province thus seem excellent. A number of large unexplored areas remain in the Moncion and Cumberland Subbasins and in parts

Jan 1, 1984

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By J. K. Van Beek

The Deep Underground Science and Engineering Laboratory (DUSEL) is a scientific facility that will be placed in the deeper reaches of the Homestake mine, Lead, SD. Our team of geologists and engineers is carrying out the first scientific project awarded to the site ? Towards a Transparent Earth. Taking advantage of the thousands of open exploratory and sand-line holes, we are installing the beginnings of a seismic observatory. Each installed station consists of a 3-D accelerometer package and a 1 nanoradian 2-D tilt meter. In order to allow for a variety of monitoring and characterization studies, the array instruments are sensitive over the frequency bandwidth of 0.2 - 1 KHz. Three, three component accelerometer stations are currently installed ? in a 140 m deep bore beneath the slurry pump house, and in 12 m deep bores on the 2000-foot level, 800 and 400 m from the Ross shaft. There is a tilt-meter installed at each 2000 level station. These installations are in 150 mm diameter sand-holes. From the currently installed tilt sensors we are investigating solid earth deformation as a response to tidal potential. The accelerometers are being used to locate and characterize events associated with mine dewatering and rehabilitation.

May 1, 2009

A Joint Venture between Hope Bay Gold Corporation and Miramar Mining Corporation recently acquired the Hope Bay project in Nunavut, which represents the first discovery of a major new Archean greenstone gold belt in Canada since the discovery of Hemlo in 1982 and the Yellowknife belt in 1938. Located some 685 km North of Yellowknife, the Hope Bay Belt is geologically comparable to the other major gold producing regions of Canada. The initial discovery of gold mineralization in 1992 led BHP to acquire virtually all of the Hope Bay belt. Over the subsequent 6 years, BHP expended C$85 million on exploration, including 180,000 meters of drilling, 2.3km of underground workings and a 27,000 tonne bulk sample, as well as extensive environmental and economic studies. Hope Bay Gold and Miramar acquired the Hope Bay property in December 1999 for a cost of C$27 million, considerably less than the C$85 million spent by BHP in exploring the property. They both hold 50% of the project, and share expenses equally. Hope Bay Gold is the manager of all exploration phases and Miramar will manage feasibility, construction and operations. The Hope Bay Joint Venture controls 1,117 sq. km., covering virtually the entire 80 km long Hope Bay and adjacent Elu greenstone belts. We believe that Hope Bay is one of the best-undeveloped gold projects in Canada. Work to date has defined a global resource in excess of three million ounces of gold in three principal deposits, each of which is open to extension along strike and to depth. A C$17 million work program for year 2000 focused on advancing a significant portion of the gold resource to a measured and indicated category. This will provide the basis for initiation of a feasibility study in 2001. The 2000 drill program was one of the largest undertaken in Canada last year, and is a clear indication of our confidence that Hope Bay will develop into a major gold producing district. The majority of the potential mineable areas known to date lie within 350m of surface and would be accessed through a combination of open pit and declines. Currently, development of a 1,800 to 2,000 tpd gold mine producing in excess of 300,000 ounces of gold per year at cash costs below $US200 per ounce is envisioned. In addition, the exploration potential on the 80 km gold belt at Hope Bay is clearly tremendous.

May 1, 2001

By D. Cruden

DISCODAT is a system of computer programs written for CANMET, Canadian Department of Energy, Mines and resources, to be used in analyzing geological data for rock slope design. The programs were written in Fortran IV for an IBM 360/67 computer. A program conditions field data from field forms for storage in a line file. Data may be selectively retrieved from the line file by a general retrieval program which uses a variety of relational operators. The retrieved data may be displayed as structural diagrams or histograms produced on a line printer or in a number of maps produced on a drum plotter. There is a logical sequence which leads to the characterization of those elements of the subfabrics of a rock mass which may be kinematically active. Structural domains within the rock mass can also be outlined by a procedure described as areal analysis. Costs for a complete analysis are usually substantially less than $l/discontinuity.

Jan 1, 1978

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By R. W. Brock

This subject is too broad and comprehensive to be dealt with adequately and authoritatively in this paper. It calls for the knowledge and experience of many men, but the results from such collaborative effort would be of great value, particularly if similar reports of the principal mining districts of the world were made on a standardized basis so that conditions everywhere might be directly and accurately compared. In considering conditions affecting mining in British Columbia, unfavourable as well as favourable factors must be taken into account. The unfavourable are apt to loom large and to be exaggerated rather than minimized; for it is human nature to see the blackness of the cloud rather than the silver lining; to think that one's own undertaking is beset with peculiar difficulties, and to attribute lack of greater success to out-side causes rather than to personal shortcomings. It should be recognized, however, that there is no country where the conditions for mining are ideal. The ideal mining country is the product of imagination, invested with every favourable condition found anywhere, but with none of the unfavourable conditions that are always present in reality. So if British Columbia has some handicaps to the industry, it is in good company. What is important is that the advantages compensate for the disadvantages, that the balance will compare favorably with that of competing states, for mining, like every other industry is competitive, and the cost of one's product must have a definite relationship to its price in the world's market.

Jan 1, 1924

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

This study examined the effects of pH and sulphate concentration on the surface charge and stability of alumina and pyrite dispersions. The relationship between these properties was investigated using measurements of electrophoretic mobility and settling velocity. The maximum aggregation for both minerals was observed near the iso-electric point (iep) where the force of repulsion is at a minimum. Aggregation decreased at pH values away from the iep, where an increased surface charge causes electrostatic repulsion between particles. Zeta potential data revealed that sulphate ions were adsorbed only on positively charged surfaces for both minerals. Adsorption of sulphates on the alumina surface increased aggregation by reducing the surface charge from >+25 mV to close to zero. These results indicate an electrostatic bonding of sulphate ions to alumina surface. Preliminary results on the interaction of pyrite and sulphate ions indicate a similar response.

Jan 1, 2004

By W. R. Bacon

"MAGNETITE HAS BEEN found in many .parts of the coastal area of British Columbia, but the more important deposits are on Vancouver Island and Texada Island. The locations of these deposits are shown on Figure 1.Interest in the magnetite deposits dates back to the 1870s, when land was acquired on the southwest coast of Texada Island by the Puget Sound Iron Company. This ground included the Prescott, Paxton, and Lake deposits. During the years 1885 to 1903, and 1908, 28,898 tons of magnetite ore was shipped to the company's blast-furnace plant at Irondale, Washington, U.S.A. This production was almost entirely from the Prescott open-pits.In the years following the Texada Island discoveries, other magnetite deposits were found in the coastal area, and various plans were proposed to utilize the local ores in the establishment of a steel industry in the Pacific Northwest. None was carried to fruition but, in 1951, open-pit mining was begun at Iron Hill, Vancouver Island, to furnish iron concentrates for steel mills in Japan. In 1952 mining of the Texada deposits was resumed to supply the same market. Production figures for these recent operations are as follows:"

Jan 1, 1949

By D. G. Sinclair

IN surveying the changes that have taken place in the mining industry of Ontario in the past ten years, the striking growth of the gold mining industry first attracts attention. In 1925 there were only twelve regularly producing gold mines in the Province, six of which were located in the Porcupine area, four at Kirkland Lake, and one each at Larder Lake and Boston Creek. In contrast with this, the year that has just closed (1935) has seen production on a steady basis from forty mines, with what may be termed spasmodic production from twelve other properties. This so-called spasmodic production is, however, responsible for the recovery of gold to an estimated value of between $75,000 and $100,000 during the year. Further illustrating the expansion in the gold mining group is the activity in the exploration and development of properties. In 1925, mining operations were conducted at 29 properties which had not reached production, while in 1935 work of this nature was carried on at 87 such properties. It is of interest to note that of the six properties listed as producers in Porcupine ten years ago, five are still producing at rates considerably in excess of the tonnages handled at that time. In fact, the estimated tonnage treated at these mines in 1935 exceeds the 1925 tonnage by approximately half a million tons. In Kirkland Lake, the figures are still more striking. The four mines in production in that camp in 1925 milled 346,584 tons, producing bullion to the value of $5,132,128, while in 1935 these same mines treated approximately 1,643,000 tons, with a recovery of roughly $29,300,000. While Porcupine and Kirkland Lake remain the great gold-producing camps of the Province, the growing importance of the newer areas is readily appreciated when we consider that in 1935 the mills of these areas treated over 1,000,000 tons of ore for a production in excess of $7,500,000. Pro-duction from these newer districts first became of importance in 1930 with the commencement of recovery at the Howey mine, in Red Lake, and the Minto, in Michipicoten. Since 1930, eighteen new gold mills have gone into production in the Red Lake, Little Long Lac-Beardmore, Pickle Crow, Sturgeon Lake, Michipicoten, Sudbury, and Matachewan areas. In respect to silver mining, the period under review has seen a considerable slackening of activity, due to a generally unstable and depreciated price for the product and to the exhaustion of ore reserves in the mines.

Jan 1, 1936

By E. Nurminen

Thermal transport properties of copper flash smelting flue dust have been investigated. Such values of the dust are needed to correctly model the process and to optimize its heat recovery performance. Dust accretions on heat recovery boiler walls may have a significant influence on the boilers heat transfer efficiency. Measurements of the thermal transport properties have been made for industrial flue dust and for pure sulphate components. The measurements have been conducted at temperatures up to 400 °C and the effect of porosity on these properties has also been investigated. The results indicate that the flue dust and the sulphate components are effective thermal insulators and the dust build-up on the boiler walls is likely to greatly decrease the heat transfer efficiency of the boiler.

Jan 1, 2007