Search Documents

By P. Hubert, J. P. Ildefonse, F. Qafssaoui, J. Poirier

Corrosion tests by corrosive alumina-lime slags were carried out on commercial high alumina bricks used in steel ladle linings and model refractories (with different raw materials : bauxite, andalusite, and different microstructures). Using (SEM) scanning electron microscope and (EDS) energy dispersive spectroscopy, microstructures of slag-corroded refractory interfaces were studied in detail. The monomineral and glassy phases, the composition of reaction products and chemical profiles were determined. A thermochemical analysis based on phase equilibrium diagrams has permitted to estimate the proportion and the composition of the high temperature intergranular liquid phase. These data were compared to the experimental microanalysis results. The viscosity of the high temperature liquids were calculated according to Urbain 's model and the relationship between the viscosity and the penetration of liquid phases were discussed. These theorical and experimental results were used to understand the complex phenomena of slag penetration and corrosion of andalusite and bauxite refractories at high temperature and to propose new ways of improvements for the formulation of high alumina refractories.

Jan 1, 2004

By R. G. L. McCready, R. O. van Everdingen, M. Kalin, R. van Everdingen

"This paper is based on data generated between October, 1986 and October, 1989, during the implementation of an Ecological Engineering close-out for a zinc mine in Northern Ontario, where 690000 tonnes of tailings contain 41.1% pyrite and 4.1% pyrrhotite. The objective was to determine rates of sulphide oxidation and iron precipitation in the tailings. Those rates are relevant for the assessment of the long-term effectiveness of biological systems employed in the removal of heavy metals from contaminated drainage issuing from tailings.Data were collected on the topography and stratigraphy of the tailings basin, subsurface temperatures and groundwater levels, and chemical analyses were made of water samples collected from a number of piezometers. The thickness of unsaturated tailings varied widely between individual piezometer locations; annual maxima ranged from 0.67 m to 3.55 m, and annual minima from 0 to 2.68 m. Sulphate concentrations ranged from 36 mg/L to 20180 mg/L; iron concentrations from 0.36 mg/L to 9938 mg/L; and zinc concentrations from 0.33 mg/L to 1123 mg/L.The geochemistry of the piezometer samples suggests that some of the initial Fe content, resulting from metal sulphide oxidation, is subsequently precipitated in the tailings pile and, possibly, in the underlying unconsolidated sediments, probably in the form of iron-hydroxide and Na-jarosite. Other metals such as Zn may be co-precipitated with Fe. The discharge of a portion of these metals to the environment would be delayed by this process. Some of the initial sulphate may also be lost from solution, probably by precipitation of gypsum; approximate saturation degrees for gypsum ranged from -3.27 to +0.47. The precipitated minerals will somewhat decrease the porosity and permeability of the tailings.Sulphide-oxidation rates, calculated using the analytical results and the estimated amount of annual recharge at the tailings site, average 0.0057 mol/kg/yr. Calculated iron-precipitation rates average 0.000386 mol/kg/yr. It is concluded that the characteristics of seepage from mining wastes may change with time, reflecting the solubilization of precipitated secondary minerals."

Jan 1, 1992

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Numerous schemes have been proposed in the past to evaluate the shear strength of rock discontinuities based on in situ and laboratory testing. Due to scale effects, in situ testing is the most reliable way to assess the shear strength parameters. However, practical reasons often impede this kind of testing. This is unfortunate because advances in theoretical rock mechanics are still dependant on qualitative experimental works. This paper presents a mobile high capacity shear apparatus developed for in situ direct shear testing of discontinuities along with testing methodology. The apparatus has the advantage of being simple, although of high capacity, and can be moved to different site locations for other tests. The in situ test was performed on a natural rock outcrop of schist with subvertical schistosity. A concrete block 50 x 50 cm with a base layer of high strength mortar was cast on the rock surface. Prior to the test, the concrete block was lifted and repositioned to have an unbonded joint but with interlocking asperities. The shear load was applied perpendicularly to the schistosity direction. The test was conducted in a constant normal load (CNL) condition. Both normal and shear loads were applied manually. The instrumentation consisted of two load cells for shear and normal loading, eight displacement laser extensometers for shear, normal, and lateral displacements and fourteen acoustic emission sensors for monitoring evolution of asperities’ degradation during the test. The friction angle obtained is 72° for the peak and 58° for the residual. The high values of friction angle indicates that first-order roughness and good interlocking of the joint surfaces can result in high shear strength parameter values in a rock generally regarded to have low values.

Jan 1, 2015

By David Lewin

The journey toward cleaner coal-fired power generation is driven by technological improvements, more stringent regulations around greenhouse gas and other air emissions, and the potential of one of Canada?s most abundant resources. Within this context, EPCOR is leading efforts to commercialize gasification technology to produce electricity with near-zero emissions. By turning coal, oxygen, and water into synthesis gas through a gasification process ? and then capturing CO2 ? it is possible to dramatically reduce greenhouse gas and smog-related emissions. EPCOR is conducting front-end engineering and design work on an Integrated Gasification Combined Cycle technology (IGCC) utility-scale plant ? in conjunction with the Canadian Clean Power Coalition ? at its Genesee site, west of Edmonton. EPCOR, the Alberta Energy Research Institute, and Natural Resources Canada have each contributed $11 million to the $33 million project. A critical element of the project features the capture of CO2, which would be piped underground for long-term sequestration, or for use in enhanced oil recovery (EOR). The combination of IGCC and CO2 sequestration, at this scale, has not been used anywhere else in the world.

May 1, 2008

By J. M. Skeaff

"The main solution, ore and residue pulp streams in the Rio Algom Quirke I uranium mill at Elliot Lake have been sampled and analyzed for radium-226. Analysis of the ore and leached residues indicates that Ra-226 dissolves and precipitates within the first pachuca tank. A maximum of approximately 0.2% of the Ra-226 in the ore remains in solution during leaching.IntroductionConcern over the acid drainage and radionuclide dissolution problems associated with uranium tailings disposal sites in Canada has prompted investigation into methods for improving current uranium processing practice.Present commercial practice usually involves leaching of the uranium ore with sulphuric acid, ion-exchange separation of the uranyl sulphate complex from the leach liquor and"" precipitation of the uranium as yellowcake. Daughter products of U-238, such as Th-230, Pb-21O and Ra-226 remain with the tailings and undergo long-term dissolution.Table I summarizes the probable behaviour of the radionuclides during milling. The concern here is with Ra-226, because it will deposit in the bones if ingested and is ""thus considered a serious health hazard(1), Similarly, Po-218 and Bi-214, which are daughter products of Rn-222, can be retained in the lungs and are considered to be the principal sources of radiation dosage(2) arising from the inhalation of Rn-222. Previous investigations(3-9l indicate or imply that Ra-226 undergoes redistribution during milling. However, detailed published information on the behaviour of Ra-226 in the uranium milling process appears to be lacking. A knowledge of the behaviour of Ra-226 in uranium mills, particularly during leaching, could lead to improved methods for its control.This paper reports the occurrence of Ra-226 in the Rio Algom mill. The main objectives of the study were to determine (1) the distribution of Ra-226 within the solids, (2) at what point, and how rapidly, redistribution occurs and (3) whether there are high concentrations of Ra-226 in solution."

Jan 1, 1981

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By Arnold R. Miller

Overview ? Vehicle Projects LLC (prime contractor) and the Fuelcell Propulsion Institute have developed the world?s first fuelcell locomotive. ? Principal applications are underground mining and tunneling. ? Because fuelcell vehicles solve the problem of underground emissions, mining is expected to be their first commercially viable market. ? The first year of a three-year project to develop a fuelcell mine loader is funded and underway.

May 1, 2002

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By Changmiao Liu, Dong Dong

"Magnesite is a major mineral resource in China, whose output and export are massive and quite important to the world. Flotation performances of eight anionic collectors on magnesite were studied to find the proper ones. Micro-flotation results indicated that collectors of HOl, SDBS and AEP had outstanding flotation performances on magnesite, with the recovery ratio all reaching above 90% in a wide range of alkaline pulp. Solution chemistry calculation, Zeta potential and FTIR measurements were employed to reveal the interaction mechanism between anionic collectors and magnesite surfaces. Solution chemistry analysis indicated that the main active components of HOl, SDBS and AEP were anions and association complex anions in alkaline pulp. Magnesite surface was negatively charged in the alkaline pulp. The active sites on magnesite surface were mainly the components of MgOH-, Mg (OH)2, and MgCO3 when the pulp pH was over 8. Anionic components of HOl, SDBS and AEP reacted with Mg in magnesite surface to make the insoluble anionic salts. And the chemical adsorption was confirmed by the FTIR measurement evidences.INTRODUCTIONAs an important industrial mineral, magnesite has been widely applied in metallurgy, building materials, chemical industry, agro-pasturage and other fields (Hu et al., 2006). It is a major mineral resource in China with abundant reserves. Its output and export are massive and quite important to the world. Liaoning province is rich in magnesite, whose reserves and production both come first in China. So far the proven reserves have reached 2.91 billion tons, accounting for more than 90% of total reserves in China, and more than 25% in the world (Li et al., 2012).Magnesite ores in Liaoning province mainly contain crystalline magnesite, and the gangue minerals of quartz, dolomite, talc, tremolite, chlorite and carbonaceous materials. Some ores also contain a little pyrite, chalcopyrite, hematite and apatite. Most of the ores must be preprocessed to separate the useful parts from the large amount of gangue minerals, so that their value and industrial application can be enlarged and promoted.Flotation is commonly used to process the magnesite ores, and the conventional flotation methods include anionic and cationic flotation. In the former, gangue minerals of silicates were separated by using amine type cationic collectors. After the impurity minerals were removed, high qualified magnesite concentration could be gained. For the cationic flotation method, it had some drawbacks of lower recovery ratio and poor performance in the lower temperature pulp (Li et al., 1995)."

Jan 1, 2016

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By F. P. Hassani, J. F. Boily, A. M. O. Mohamed, M. Hossein

The optimal geochemical parameters required to form ellringite in a lime-remediated site have been investigated with the use of thermodynamic modelling. The speciation of sulphate and 10 metals analyzed in samples of a mine tailing from northern Quebec was calculated with a computer model. The model also includes calcium, which would result from the addition of lime to the system. Two speciation calculations were done. The first one is a hypothetical speciation before the onset of precipitation and was used to devise the stability fields of minerals susceptible of forming in high pHs. The stability fields were determined by building activity ratio diagrams with sulphate, aluminum and calcium species concentrations for pHs ranging from 4 to 14. The investigation was carried out for a 25°C solution with an ionic strength less than 0.12. Thermodynamics predict that an optimal stability field for ettringite in the mine tailing samples containing 10-3 mol/L SO4-2,10-2 mol/L of AI(OH)4 requires at least 10-2mol/L of Ca+2 and a pH larger than 11.6. The sulphate contents of the mine tailing samples, however, limit the precipitation of ettringite and monosulphate could be an end-precipitate. The second speciation is in equilibrium with precipitates and provides information on the speciation of the residual metals. If ellringite could be precipitated as a stable form, it could serve as a sorptive agent for residual metals, and, due to its binding properties, consolidate tailings.

Jan 1, 1995

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

"Line Creek Resources Ltd. produces three million clean tonnes per year of metallurgical and thermal coals for the international market. The mining operation, which is located in the mountains of southeastern British Columbia, produces coal from four pits by conventional truck and shovel methods.The South Pit, which has been in operation since J982, has a benched highwall 490 m in height. Shallow dipping coal seams at the base of the syncline formation will be exposed in the highwall over the next four years of pit life. The first of these seams, which will measure 500 m in final highwall length, was exposed in J994. An auger, powered by a 1250 hp engine capable of cutting 2.2 m diameter holes, was brought on site in J994 and has proven to be a successful means of recovering coal from the J3 m thick seam.This paper covers the background to the selection of an auger mining method to recover highwall reserves together with the geotechnical and methane considerations for this approach.IntroductionLine Creek Resources Ltd., a wholly owned subsidiary of Manalta Coal Ltd., owns and operates the Line Creek mine. The operation which consists of four active pits, a processing plant, and rail loadout is located in the southeastern coal fields of British Columbia. Figure 1 shows the general area.The coal bearing sequence at the mine is preserved on the east and west limbs of a major syncline. Up to twelve mineable coal seams, ranging in thickness from 2 m to 15 m are contained in the formation. Within the pits the seams are stratigraphically consistent and structurally undisturbed, except for small-scale thrust faults that create multiple repeats of the seams."

Jan 1, 1995

By R. B. Roberts, A. L. Mular

A simple way to determine the IEP of oxide minerals is described. The method is shown to apply for fine powders of Fe203 and ZnO. The IEP lies at pH 6.95 for Fe203 and at pH 9.08 for ZnO.

Jan 1, 1966

By W. Petruk

"D. Doyle How large is the beam to which you referred? Are we considering Watts, Griffis the probe of a 1 micron sized particle?& McOuatReply Yes. The beam would be about 1 micron. We could enlarge or reduce it depending on the current in-put.D. Doyle Then chemically bound material we might not see. If you are restricted to 1 micron then you would not be able to separate things smaller than this. Is this not so?Reply We won't be able to analyse it but we will see it as the scanning electron microscope has a resolution down to about 0.1 microns. We should be able to get the general composition of such a grain plus its surrounding grains. We feel we can then make a reasonable estimate if it were as small as 0.1 microns. An accurate analysis would be achieved with grains of 3 and 4 microns.D. Doyle Would this have an application in the hydrocarbon field?Reply The lowest atomic number would be sodium. We wouldn't be able to go below that atomic number. Anything with sodiumor a larger atomic number would enable us to analyse the carbon.M. Fairwether Do you have any policy relating to priorities. For instance areCominco companies going to be limited in the amout of samples permitted to give everyone a chance because quite frankly our company, and I'm sure all base metals companies can hardly wait for the installation of this equipment. I can forsee two years back-log of work in the first month.Reply Quite frankly, I haven't looked at this. At the present time the work is under the START program but I suppose we will have to look at possible changes. Anything under the START program has first line priority.B. Thorndycraft Will the briquetting of samples be automated as well? Pinson MiningReply No, not at this point. Our polish section laboratory is first-class and can turn out 18 polish sections a day which is more thar we can handle.B. Thorndycraft With the capability of this machine to operate in a hands-off manner perhaps it could start to look for the 5 micron gold particle in tailings?Reply I have such a program using a wave-length spectrometer rather than the energy dispersive. The wave-length spectometer is about 10 times as sensitive and would scan the section much faster. A one inch diameter polished section would be scanned in about 7 hours for anything 1 micron or larger."

Jan 1, 1984

By R. D. Brown

Ever since British Columbia started the ball rolling in 1974 with the introduction of its now-defunct Mineral Royalties Act, all Canada's resource-based provinces have significantly altered their mining tax systems. The last resource-based province to abandon its pre -1974 mining tax structure is New Brunswick, which introduced a new mining tax regime in the summer of 1977 to take effect from April 1 1977. The new structure, which represents the outcome of considerable study and discussions with industry representatives, contains some intriguing concepts which make Nero Brunswick's new mining tax system unique among the Canadian provinces.

Jan 1, 1977

By R. J. Grant, D. W. Scott, M. A. Cooper, E. R. Shannon

"The Brunswick No.12 site concentrator processes 10,500 tonnes per day of a complex lead, zinc, copper and silver ore producing four concentrates by differential flotation. Research over the years has led to increased understanding about the mineralogical and flotation characteristics of the ore. A pilot plant study conducted at Lakefield Research, primarily designed to investigate the technical feasibility of semi-autogenous grinding, provided an opportunity to test recent theories about grind size,, reagent schedule and flowsheet configuration.A fundamental approach was taken with each of the unit processes involved in grinding and flotation. Basic operating and metallurgical criteria were established in each area and a step-by-step implementation program initiated in the plant.Significant improvements in metallurgical and financial performance have been realized through the application of basic grinding and flotation principles using conventional milling equipment and without major capital expenditure. Current operating practice is detailed and metallurgical advancements cited.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mines near Bathurst, New Brunswick. Brunswick is a publicly traded company with majority ownership held by Noranda Minerals (63%). In addition to the No. 12 underground mine, the company operates a lead smelter and phosphate fertilizer plant in Belledune, N.B. and maintains a 25% interest in a joint venture with Noranda Minerals' Heath Steele mine near Newcastle, N.B. Through the four operations, a total of 2000 people are directly employed with fixed assets totalling Cdn$187 million (BM&S, 1991)."

Jan 1, 1993

By A. T. GRIFFIS, R. J. GRIFFIS

A large magnesite-talc body is locared in Delora Township, 11 km sourh-southeasr of Timmins, Onrario. The deposit occurs in part of an Archean greensrone belt dominated by volcanic and sedimenrary rocks and large bodies of ultramafic intrusions. The magnesite-talc zane is abour 1800 m long, has a maximum width of 300 m and has been drilled ro 120 m below surface. Chemical analyses of rhe main carbonate zane average 20 ro 28% soluble MgO (magnesia), 5 ro 6% rota/ iron oxide and less rhan 0.1 % CaO (lime). Mineralogically, the zane consists of approximately 54% magnesite, 28% rate, /5% quartz and 3% hematire. Perrographic srudies suggest that rhe various assemblages of magnesite, rate, quartz and serpentine were derived from a parenr serpenrinire (after dunire). An early carbonitization stage, which produced a high-magnesite, low-talc assemblage, preceded a farer decarbonitizarion stage, which formed rhe main magnesite-talc assemblage. Despite a favourably low calcium oxide content of rhe magnesite-talc rock, considerable iron in the magnesire /at rice has limited the quality of the beneficiared product: rhe besr flotation concentrate to dare yields 92 to 94% dead-burned MgO. Experimen- I L t r i i c:~:.•-4- -------- ? -_;> ,•----1---- ta/ work continues on finding a process whereby high-purity magnesia can be produced on a commercial scale.

Jan 1, 1984

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973