Search Documents

By James A. Finch, Yue Hua Tan, Wei Zhang

"The paper is part of our study of the frother structure-property relationship using bubble rise velocity. Single bubble rise velocity profiles were determined in a 350 cm column for surfactants from the polypropylene glycol (PPG) family. Using velocity at 300 cm, the concentration to reach minimum velocity (CMV) is determined. The CMV is shown to decrease as alkyl chain length (n, number of carbons) increases and as the number of propylene oxide groups (m) increases. Linear correlations log CMV vs. n and m were observed. Taking literature data for critical coalescence concentration (CCC), linear log CMV vs. log CCC correlations were also noted. Mechanisms are briefly discussed, and prediction of CCC made for a commercial polypropylene glycol.INTRODUCTIONAs one of the great enabling technologies of the 20th century, froth flotation is a highly versatile method for physically separating minerals by exploiting differences in wettability (hydrophobicity). Over the last century, flotation reagents have undergone significant developments (Khoshdast and Sam, 2011). One important group of reagents is frothers which are used to reduce bubble size, slow bubble rise velocity and help stabilize froth (Klimpel and Isherwood, 1991).Frothers, originally derived from natural sources (e.g., pine oil and cresylic acid), are largely replaced today by synthetic products which provide more consistent properties. Polyglycols, based on PEO (polyethylene oxide), PPO (polypropylene oxide), or PBO (polybutylene oxide) groups, were first described by Leja and Nixon (1957) and have attracted wide use since then (Farrokhpay 2011). The chemical structure of polyglycols can be represented by a general formula: R(X)mOH, where R = H, or CnH2n+1 and X stands for EO (-C2H4O-), PO (-C3H6O-), or BO (-C4H8O-). The polypropylene glycol ethers (CnH2n+1(PO)mOH) are the most common of these reagents (Pugh, 2007) and the focus of this study.In general, the chemical structure of frother molecules comprises two parts, a non-polar hydrophobic hydrocarbon (alkyl: CnH2n+1) chain and a polar hydrophilic head. By introducing the ether -Olinkage, which acts as another polar site, the propoxy group (-OC3H6-) in the structure makes the frother readily soluble in water (Somasundaran and Wang, 2006), facilitating the industrial use of these frothers. Available as by-products, Dow Chemicals introduced as series of polyglycols, e.g., Dowfroth (DF) 200, 250, 263, and 1012, the most familiar being DF250 (CH3(PO)4OH), a polypropylene glycol methyl ether. While no longer available from Dow, these and other polyglycols are still widely used."

Jan 1, 2016

By B. Nanthakumar

The impact of stockpile oxidation on chalcopyrite was studied through collectorless and collector-induced flotation conditions. In both cases, the Cu grade-recovery performance of stockpiled ore showed relatively poor concentrate grades with respect to that of a fresh sample. However, the oxidation had a minor effect on chalcopyrite recovery itself. The poor concentrate grades resulted from dilution effect primarily by excessive flotation of pyrrhotite. Size-by-size analyses indicated that for the collectorless flotation, the recoveries in the coarse and fine particle-size regions, were higher for fresh ore than for stockpile sample. A greater impact was seen in the coarse size regions for both types of sample, compared to the collector-induced case. The Cu recoveries showed a remarkable increase in the coarse size range for both samples when a collector was used. However, the case for stockpile sample was a marginally higher compared to the fresh sample. This difference has been offset by an opposite trend that was observed between these two samples in the fine size region. It is concluded that in contrast to the case with nickel-bearing sulphides, stockpiling conditions do not show a significant adverse effect on behaviour of chalcopyrite due to its strong floatability, regardless of oxidation.

Jan 1, 2007

By Joseph Bradley

THROUGHOUT this article, minerals used in the paint industry are designated 'pigments'. They may be classified in two groups: (1) Pigments which are used in the state in which they occur in nature, requiring only mechanical preparation. (2) Pigments which require heating or chemical treatment before use, in order to obtain from them a product of the desired quality or shade of colour. They may be further classified according to colour, as follows: White Pigments .-These include calcium carbonate (chalk, marble), gypsum and alabaster, kaolin-or china-clay, and magnesia. However, the white pigments most extensively used are compounds prepared chemically from minerals containing lead, zinc, titanium, and antimony. The white pigments are of particular importance because, not only are they used by themselves, but they also serve as adjuncts to other colours for the production of special shades. Yellow Pigments.-These are mainly naturally occurring ferric hydroxides, as limonite and bog iron ore, or similar. compounds prepared artificially. Brown Pigments .-Pigments of this group are distinguished for their beauty and depth of colour, and many of them are used in the finest of paintings. Familiar names are sienna, umber, and Vandyke brown. They are for the most part ferric hydroxides, containing varying amounts of water; but the group also includes a manganese brown, which consists chiefly of a mixture of oxide and hydroxide of manganese. Red Pigments.-Chief among this group is ferric oxide, known under various trade-names, such as Canadian red, Persian red, etc., and also the much prized and somewhat rare vermilion. The pigment used is either naturally occurring hematite, de-hydrated limonite, or artificially produced red ferric oxide.

Jan 1, 1937

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By X. F. Liu, O. Buzzi, Y. Sieffert

This study falls in the context of underground coal fires (UCF) where burning coal can elevate the temperature of a rock mass in excess of thousand degrees. The objective of the research was to experimentally investigate the change in mechanical behavior of a rock when subjected to temperatures up to 900 °C. Several blocks of an Australian mudstone were collected from a mining site in New South Wales, Australia. X-ray diffraction and thermal-gravimetric analysis were conducted on powdered rock in order to determine the critical temperatures at which the main mineralogical changes occur. Then, cylindrical specimens were prepared from intact rock blocks for unconfined compression tests. These rock specimens were then treated by heating in a temperature-controlled furnace at temperatures varying from 100 °C to 900 °C. The heating process consisted of two stages: raising temperature with very slow rate of 1 °C per hour followed by a holding period of 24 hours and then a slow cooling process to room temperature. The compression tests were carried out on treated rock specimens to characterize the change in compressive strength. The macroscopical study was complemented by microstructural investigations via optical microscope, scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). Results show that the unconfined compressive strength of mudstone decreases with increasing heating temperature up to 450 °C, beyond which it increases. This can be explained by the combined effects of micro cracks and mineral thermal reactions caused by heating process.

Jan 1, 2015

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By C. Zangerl, W. Fellin, M. Holzmann, B. Hofer, S. Perzlmaier

"Four deep-seated rockslide systems were investigated and are under surveillance by TIWAG (Tyrolean hydro-electric Company) since the mid-1960s after impoundment of Gepatsch reservoir began. These rockslide systems consist of several individual sliding masses (slabs) which show variable activity from zero to a few centimetres per year. The focus in this paper will be on the findings for the transient deformation behaviour of the Hochmais slab which is part of the “Hochmais-Atemkopf” rockslide system.The rock mass has slid over moraine deposits in the last post-glacial period and was in equilibrium (or slow to extremely slow moving, respectively) until the filling of the reservoir began. During the initial reservoir filling in summer 1964 considerable movements had been observed over a length of 1000 m accompanied with an activation of the Hochmais slab. Geological investigations, additional surface and subsurface measurement showed that the sliding mass is characterized by an en bloc movement and the deformation accumulates within a several metre thick shear zone located within the moraine. In contrast to the deformation characteristics for the first impoundment process (1964 – 1966) where the magnitude of deformation occurred during impoundment, the maximum amount of deformation since 1967 occurs during the drawdown of the reservoir. Based on long term measurement it can be shown that the magnitude of deformations per year correlates with the minimum storage level in the reservoir. Other external influences such as precipitation and snowmelt have no observable impact on the deformation characteristic of the landslide. On the basis of long-term data series it was possible to determine the factors of influence and to elaborate a conceptual mechanical model which describes the transient deformation behaviour of the Hochmais slab induced by the drawdown of the reservoir. The mechanical model considers the reduction of uplift forces in the highly fractured and permeable rock slab during drawdown as well as increasing seepage forces in the less permeable moraine material."

Jan 1, 2015

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

By Y. L. Mehta

The working experience of the Zinc Smelter, Debari, Udaipur with process modifications and iron control practices is described in detail in this paper. Most of the modifications were made at different times as part of capacity enhancement campaigns that led to distinct advantages, thereby increasing both zinc production and recoveries. This smelter came into existence in 1968 with a humble beginning of producing 18,000 metric tonnes (MT) of zinc per annum, using the conventional batch hydrometallurgical roast-leach-electrowinning technology. Zinc production capacity was increased stepwise to 45,000 MT, 49,000 MT and 59,000 MT, by making suitable process modifications and adopting new technologies, particularly in the leaching section. During these modifications, the process of iron separation as Moore cake was also changed to jarosite cake production. At present, jarosite is being disposed in a secured landfill at the Zinc Smelter, Debari (ZSD) and as Jarofix at the Chanderiya Lead Zinc Smelter (CLZS). As a result of subsequent in-house performance improvement and debottlenecking campaigns, this smelter could achieve further increases in production. Zinc production for the financial year 2005-06 was 81,000 MT.

Jan 1, 2006

By Frank Lemy

This paper presents an application of digital face mapping in an underground mine. Based on photographs it was possible to construct discontinuity maps, which were used to characterise the rock mass. The results were compared favourably with values obtained through scanline and area sampling mapping for the same site. The case is made for digital mapping as a safe, fast, and efficient way to characterise rock mass structure for engineering purposes.

May 1, 2001

By J. Chao, C. Tan, N. Stubina

"Since J978, Falconbridge Limited has operated two electric furnaces at its nickel-copper smelter in Sudbury. As part of its S02 Abatement Program, the smelter has undergone many changes over the last seven years.This paper describes the impact of these changes on the operation of the furnaces. Some of the topics to be covered include: the installation of sidewall copper coolers; current operating conditions; and furnace heat and mass balances. HistoricalFalconbridge began smelting ores in the Sudbury area in 1930. The original smelter consisted of a 1.3 m by 3 m blast furnace and two 4 m by 6 m converters. The blast furnace was supplied with untreated mine are and molten slag/matte was discharged into a round settler.In 1933 the smelter began treating flotation concentrates. The concentrates were mixed with fine magnetic ore and flue dust, then sintered on down-draught Dwight Lloyd machines. This provided an agglomerate suitable for furnace burden which was charged to the blast furnace while still hot.Between 1930 and 1954 nickel production was increased by lengthening the 3 m furnace to 4.6 m, then to 6 m, and later by constructing additional furnaces. By 1958, the plant consisted of one 7.5 m blast furnace, a settler, and three 4 m by 9 m converters."

Jan 1, 1994

By R. H. Duval

"In May 1936, Pamour started producing gold by cyanidation of flotation concentrates, and in 1939 was milling about 1, 600 tons per day.Refining records dating from 1939 show two oil-fired furnaces in use, (Rockwell type 46 11 x 29 11 inside oval shell).Refining time averaged 7. 83 hours during the year 1939, indicating a complete refining shift of about 9. 33 hours. That year appears to be characteristic of the period with regard to time required and results obtained.For that year total fineness (gold + silver) of the bars averaged 940 (approx.), but it frequently dropped below this figure, sometimes far below.Furnace lining life varied widely from three to seven or more months. Sillimanite was the standard lining but Mullfrax 41 was frequently used.For many years refining practice remained practically unchanged, and in 1960 procedure still consisted essentially of mixing a flux(% Composition Borax 41, Silica 11, Soda-Ash 11, Nitre 15, Mn02 22) with cyanidation precipitate in the ratio of l. 2 to l and heating to a medium heat (yellowishred, 2000° F) with a low flame for a long time. Time required was about 10. 5 hours per refining. Results were still much as detailed above.At this time it was decided to revise refining procedure, in an effort to shorten refining time and obtain consistently good bullion fineness."

Jan 1, 1965

By Moatassem Abdallah

Buildings in the United States account for 72% of electricity consumption, 40% of energy consumption, 13% of water consumption, 39% of carbon footprint, and 30% of waste output. In order to minimize these negative environmental impacts, many public and private owners are requesting that their buildings be more sustainable and certified under the widely known programs such as leadership in energy and environmental design for existing buildings (LEED-EB). To accomplish this, buildings are increasingly integrating green building measures including energy efficient lighting, motion sensors, thermal pane glass, geothermal heat pumps, EnergyStar rated HVAC systems, photovoltaic systems, and wind turbines. This research paper presents the development of an automated decision support system (DSS) that is designed to optimize the selection of green building measures which can be used to upgrade existing buildings. The developed DSS incorporates two optimization models that are capable of (i) minimizing the total upgrade costs required to accomplish a specified LEED-EB certification level such as silver or gold; and (ii) maximizing the number of accredited LEED-EB points within a specified budget of upgrade costs. The DSS is designed to identify a set of optimal upgrade decisions that accomplishes these two optimization objectives. An application example is used to illustrate the capabilities of the DSS and to validate its result.

Aug 1, 2013

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015

By Ward E. Kilby, Bruce I. Mcclymont

"Data from the South Fork Pit Area of the Bullmoose deposit in northeastern British Columbia are used to demonstrate the usefulness of microcomputers to the on-site geologist. The technique utilizes a series of digital surf aces in the form of a network of points to define various geologic parameters such as seam positions, topography and coal quality characteristics. Manual digitizing, kriging and combinations of these techniques are used to calculate these digital surfaces, the best method depending upon the type and quality of the data in question. Digital surfaces, each modelling a specific feature when combined and manipulated with the computer form a powerful tool, the deposit model. The resultant model, containing all the surfaces, is used to examine seam and inter-seam thicknesses, deposit volumetrics, seam quality characteristics and the adequacy of sampling.IntroductionCoal deposit modelling using computer-based techniques has become routine. However, a geologist working in the field, without access to mainframe or minicomputer, ha s considerable difficulty implementing these procedures. However, microcomputers, which are portable and inexpensive can handle exploration data, perform various geological analyses, and produce deposit models virtually at the same time as the data is being collected. For the on-site geologist this means that quick access to the results of such modelling could point out inadequacies in deposit definition and trends in coal quality deserving investigation."

Jan 1, 1985

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By K. Chomyn, R. Veenstra, P. Zangeneh, Hatch Ltd., C. Van der Woude, H. Ghorbani

"The furnace is the heart of smelting operations, and therefore the performance, reliability, and campaign life of the furnace are critical considerations. Furnace refractory is exposed to high temperatures and other harsh operating conditions causing brick erosion, crushing, and cracking, typically limiting the furnace campaign life and requiring costly furnace shut-downs for refractory re-lining. Despite extensive study, the in-service thermal / mechanical stresses in these complex refractory systems are not generally well understood. Hatch has developed a thermal-mechanical finite element analysis (FEA) based furnace refractory modeling approach that allows for the quantification of refractory movements, load distribution, and thermal / mechanical stresses.Due to the complexity of the refractory system, a range of models are used to identify and assess damage mechanisms and design improvements, including: 2D models, to capture expansion and movement of individual bricks, changes to load paths, and thermal stresses; and 3D models, to include the effect of differential expansion between bricks in each course, and assess overall load distributions. The 2D and 3D analyses include the effect of nonlinear temperature-dependent properties, thermal expansion, movement of individual bricks with frictional contacts (i.e., gaps can open, bricks can slide), and brick tensile or compressive failure. Both as-built and damaged conditions can be investigated (e.g., after bath zone brick erosion), for circular and rectangular furnaces. 3D models also include papering and brick joint & interface action.Analyses using these models have shown the importance of thermal stresses, papering, and geometry / arrangement of individual bricks. Results have been used to identify and assess damage mechanisms, showing good alignment with furnace autopsy observations. By using this FEA-based approach to quantify the refractory design, the risk of damage can be significantly reduced, low-cost design changes can be identified, and the furnace campaign life can be extended.INTRODUCTIONThe furnace is the heart of smelting operations and therefore the performance, reliability, and campaign life of the furnace are critical to the success of the smelting operation. Furnaces are inherently exposed to high temperatures, often in excess of 1600°C (Holappa, 2004), and furnace operating power has progressively increased over time (Voermann, Gerritsen, Candy, Stober, & Matyas, 2004). The refractory system must withstand high temperature, high heat flux, and other harsh operating conditions. These conditions are particularly significant for the furnace hearth, and can lead to damage including brick erosion due to molten material flows, crushing due to thermal expansion loads, and cracking due to severe thermal gradients within the bricks. Refractory damage typically limits the furnace campaign life, requiring costly furnace shut-downs for refractory re-lining (repair or replacement). In some cases the refractory may lose integrity causing damage to nearby equipment and harm to personnel."

Jan 1, 2016

By Karl J. C. Harries

"9.1. INTRODUCTIONIn Chapter 5 of Volume I royalties are dealt with and several topics would appear to be duplicated in this Volume. However, Volume I may be looked upon as a general guide, whereas this Volume is a reference volume. It deals in considerable detail with specific provisions and concepts relating to royalties between private parties. This does not, however, mean that Chapter 5 can be ignored. It should be looked upon as a source of general information concerning royalties between private parties and as a negotiating aid intended to give an overview of various topics. You may well find that in its general approach it will lead you to ask a question which, hopefully, will be dealt with in this Volume .It should be remembered that royalty agreements are agreements with a particular focus, and so the concepts set forth in Chapter 1 apply to them. This chapter addresses a few considerations specific to royalties that will usually form part of an agreement rather than a stand-alone agreement.9.2. FORMAT FOR ROYALTY PROVISIONSIn many of the cases where royalties arise, they are adjunct to, or part of, other arrangements. For example, a royalty may form part or all of the consideration to be given to an owner upon purchase of his property, or it may arise if a joint venturer ceases to contribute to the venture and has his interest converted to a royalty.1 It is with such situations that this section primarily deals; if the royalty is contained in an agreement that is singularly, or primarily, concerned with creating it, then it is just a normal agreement.Commonly, by the time the right to receive the royalty arises, at least some of the other provisions of the agreement have been performed and/or become redundant. For example, in an option agreement the royalty will be a continuing obligation of the optionee, usually arising only after the option has been exercised.2 In a joint venture agreement, a royalty will often arise where the interest of a non-participating venturer has been diluted and converted to a royalty, in which case the recipient will usually become a passive party, entitled only to his royalty, and most of the rights that he enjoyed as an active venturer will cease to be effective."

Jan 1, 2003

By J. J. Brummer

"A reconnaissance geochemical survey, using the stream sediment technique, is described. The survey covered an area of about 400 square miles, in the Seal Lake area of central Labrador, underlain by basaltic flows, diabase and metadiabase sills, and sedimentary rocks. Previous work had indicated numerous small copper occurrences within the Seal Lake group of rocks. Stream sediments were tested for the readily extractable copper content and total heavy metal content. The results of the copper survey did not yield any new data on the distribution of copper mineralization. Results of the total heavy metal survey attracted attention to a remote portion of the area (Ten Mile Lake), which had hitherto been regarded as having no economic interest. The anomalous values found, suggested that zinc mineralization should occur in this region. Geological mapping indicated that the rocks exposed belonged to the Letitia Lake Group, which is older than the Seal Lake Group exposed to the east, which contains the copper mineralization of the district.Investigation of the area lead to the discovery of: (1) uneconomic lead-zinc mineralization; (2) radioactivity extending over a considerable area. Evaluation of the radioactive rocks led to the discovery of columbium-thorium mineralization in amphibolite and in diopside-actinolite schists along a contact with intrusive alkali syenite.Thus a geochemical survey, which was planned to evaluate a copper province, resulted in the discovery of lead-zinc-columbium-thorium mineralization."

Jan 1, 1960

By H. Vermette, J. Demers, R. Leclerc, P. Bergeron, P. Hudon, A. Lessard

The Arvida Smelter marked its 80th anniversary in 2006. Arvida currently operates 6 potrooms equipped with prebaked side-feeding pots producing 160 000t of aluminum per year, requiring the supply of 300 000t of alumina per year. In the past, to ensure reliable alumina supplies to the pots, especially in winter, a safety stock of alumina was kept inside the plant. The improved reliability of shipping on the Saguenay River has cut the need for such a stock. However, the stoppage of 8 Soderbergtechnology potrooms, starting in the 1980s up to 2003, generated alumina from the cleaning of pot pits, totaling 18000t and leading to the building-up of a significant alumina stock again. Concerns over working conditions, effect on potroom operations, and dust emissions prevented Arvida from tackling effectively this impressive alumina stock. Yet the increasing cost of alumina has created a strong motivation to use the stored alumina. In 2004 Arvida launched a project to recycle the stored alumina. This 4-year project aimed at clearing the alumina stock without affecting the operation of the smelter. It involved changing work organization, improving equipment and controlling the effect of the recycled alumina on the smelting process and working conditions.

Jan 1, 2006