Search Documents

By J. Bakos

Solar Hydrogen Energy Corporation (SHEC Labs) recently constructed a pilot-plant to demonstrate a Dry Fuel Hydrogen Generation System that is powered primarily by sunlight focusing-mirrors. The pilot-plant consists of: A Solar Mirror Array and Advanced Solar Concentrator and Shutter System; and two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that Solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

Jan 1, 2005

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By S. Mathieu, R. Mennillod-Blondin, P. Cousin, N. Valle, H. Bouzahzah, P. Marion

The gold deposit of the Lapa mine has a complex mineralogical gold state with coarse and fine native gold, aurostibite and submicroscopic gold within arsenopyrite. A specific mineralogical characterization of the refractory fraction was conducted combining various techniques such as optical microscopy, electron microscopy, electron microprobe and secondary ion mass spectrometry. In parallel, the mineral processing behaviour and the recovery of the refractory gold were studied by pressure oxidation and cyanide leaching. This paper presents the mineralogical methodology developed to characterize the refractory gold distribution within arsenopyrite. These results are presented and interpreted in order to plot gold recovery versus sulphide oxidation. The comparison of the metallurgical behaviour yields predicted from the mineralogical data and the one calculated from leaching tests shows a good agreement and allows mineralogical explanations of the gold metallurgical behaviour.

Jan 1, 2011

By R. A. Frith

"Belts of Yellowknife Supergroup volcanic and sedimentary strata in the Slave Structural Province are separated by granitoid complexes. The strata and most intrusive rocks are 2.7 and 2.5 Ga old, but rocks around 3.1 Ga have been recognized in some of the complexes and are believed to represent a once-extensive sialic crust. Volcanics were erupted along rifts in this crust and the rifts became sites of crustal foundering and the development of troughs that filled with turbidites of volcanic and granitoid provenance. Present margins of the granitoid complexes may be close to the original margins of deposition of volcanics, with associated mineral deposits, and close to the thickest parts of basins of sedimentation.The Hackett River volcanic belt extends 100 kilometres between Mara River and Back River and is crudely S-shaped, with a northern sector surrounding a core of granitoid basement rocks, a northeasterly facin g central sector and a southerly facing southern sector. Up to 8 kilometres of andesitic volcanics with intercalated felsi c volcanic rocks are preserved within the central sector. The f elsic rocks include thick lenses of volcaniclastics with large, quartz-eye-bearing clasts, but the known metal deposits are not associated with these. Both of the deposit areas, the Hackett River area in the northern domal sector and the 'A itch ' Lake area 40 kilometres to the south in the central sector, are near the tops of relatively thin atypical volcanic sequences above suspected basement rocks. The Yava deposit near 'A itch , Lake overlies a unit of subaerially deposited, welded, andesit ic ash flows and the Hack ett River deposits overlie highly metamorphosed volcaniclastic rocks that include suspected ignimbrites.The deposits are notably argentijerous and lead-rich. They consist of stratigraphically zoned sheet-like bodies of iron sulphides, sphalerite, galena and chalcopyrite underlain by altered rocks containing chalcopyrite stringers. The Yava deposit was formed where hydrothermal fluids exuded through the fractured floor of a flooded caldera basin. The Hackett River deposits may have been formed in a similar setting and it is not inconceivable that all the known deposits in the belt were formed in a single large caldera basin, although there is no independent evidence for the required major fault separation between the Hackett River dome and the 'Aitch' Lake area."

Jan 1, 1980

By L. Cáceres, G. Leinenweber, P. Bustamante

"Given the severe scarcity of fresh water sources in Northern Chile the use of seawater has become the only alternative to allow mining expansion. This option however poses several technological challenges as a result of the high concentration of natural salts that promote various forms of metal corrosion. Therefore the steel piping protection has been a constant challenge for design engineers responsible for solving the problems of corrosion. Known protection alternatives are varied and expensive, a few of them are rubber coatings, protection based centrifuged concrete, extra wall thickness of pipes in combination with corrosion inhibitors, extra wall thickness of pipes without using corrosion inhibitors, and the use of highly corrosion resistant steel materials.In this framework the aim was to study the corrosion kinetics of carbon steel pipe API 5L X70 under electrochemical and weight loss testing. The test conditions include a range of seawater velocities between 0.2 to 3.0 m/s.For electrochemical experiments the API 5L X70 steel specimen was a 4 mm diameter disk embedded in an 8 mm diameter Teflon rod and exposed to seawater. Duplicated coupons were placed in a standard test apparatus that was built according to the standard ASTM D 2688 – 94.The main results were: a) corrosion mechanism explained in terms of the counterparts partial processes which are the hydrogen evolution and oxygen reduction reaction; b) for the test specimen a corrosion band like feature that suggest a lateral dispersion of aggressive solutions from corrosion pits; c) a range of corrosion rates between 1 and 1.96 mm/year for flow rates between 0.2 and 3.0 m/s; and d) a convenient inhibitor dose between 20–25 mg/L for optimum inhibition efficiency to obtain a maximum value of 80% for corrosion efficiency."

Jan 1, 2016

By Wang Xianzheng

For a long period of time, the Chinese Government has been attaching great importance to and supporting the rapid development of the coal industry. Particularly since more than 30 years ago, when China introduced the Reform and Opening-up policy, the reform and development of the Chinese coal industry has witnessed world-recognized achievements. National coal production increased from 618 million tonnes in 1978 to 3.52 billion tonnes in 2011. While China?s coal production accounts for 49.5% of the world?s total, its annual production growth contributes to over 80% of global production growth. China is a country utilizing coal as its main source of energy. As the Chinese Government gives support to the rapid development of new and renewable energy sources, as well as to increased coal utilization efficiency, the ratio of coal in the primary energy consumption mix will gradually decline. However, for a long period of time to come, the total volume of coal demand will keep rising modestly. The Chinese Government has been highly committed to and actively promoting the overall, coordinated and sustainable development model, which puts people first. It has put forward a strategic task to build an ecological civilization, and highlighted its resolve to uphold the basic national policy of resource conservation and environmental protection, with a view to the pursuit of sustainable development. China will incorporate its response to climate change into the national economic and social development program, and take effective measures to lower CO2 emissions 40?45% per unit of GDP in 2020 compared to 2005. At the same time, China will increase the ratio of non-fossil fuels to 15% in the primary energy consumption mix. All of the above factors have raised requirements for the Chinese coal industry, with implications for clear directions, plans and goals for the development of the coal industry.

Aug 1, 2013

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By Heather Budney

Objectives 1. Evaluate the effectiveness of ON?s EA processes using criteria from the EA and policy sciences literature. 2. Recommend improvements to the EA processes and draw lessons from the ON case for the consideration of other jurisdictions. Evaluation Process 1. Chose criteria ? 14 primary criteria (Wood 2003) ? Subcriteria from Wood (2003) and Lasswell (1971) 2. Gathered information ? 6 key informant interviews ? Published literature, policies, legislation 3. Assessed criteria and formed Recommendations

May 1, 2008

By Bétournay. M. C.

Advantages ?Safety ?Health ?Rapid, continuous development, productivity ?Stope dilution reduction Disadvantages ?High cost and long time for equipment development ?Hard rock mining condition limitations ?Size of equipment ?Equipment set-up time, down time ?Performance does not meet financial return targets ?Drill and blast retains advantage in cost, productivity, capital investment, application flexibility ?Stress accumulation issues in deep mining, ground support and material handling issues in weaker rock

May 1, 2009

By R. I. Grauch, Michael D. Glascock, Chen Nansheng, Jr Coveney, James B. Murowchick

"Unusually rich molybdenum ores (cutoff grade = 4.10/0 Mo) hosted by Lower Cambrian black shales have been mined since 1985 near Zunyi in the province of Guizhou in China. Similar ores were once worked for Mo and Ni near Dayong in the province of Hunan. In both mining areas, mineralization occurs in Lower Cambrian black shale (Niutitang Formation and stratigraphic equivalents) as a single sulfide bed or lens with exposed thicknesses up to 15 cm and reported thicknesses up to 35 cm. In addition to high Mo values (4% to 7%), ore samples contain up to 7% Ni, 2% Zn, 2.5% As, and several hundred ppb Au and Pt-group elements, but the precious metals have never been recovered from the ores. Sporadic occurrences of Mo-Ni sulfide ore beds are found in at least five provinces stretching approximately 1600 Ian from Yunnan to Zhejiang. None of the Mo-Ni ore-bed occurrences has any obvious connection with mafic or ultramafic source rocks. Similar occurrences containing elevated values for Ni, Mo, and PGE exist in Devonian black shale in the Yukon. Future exploration for Pt, Au, Mo, and Ni deposits should consider this previously unknown type of sediment-hosted mineral deposit.Sommaire - Des minerais anormalement riches en molybdène (teneur-limite = 4.1% Mo) provenant de schistes argileux noirs du Cambrien Inferieur ont été exploites depuis 1985 près de Zunyi dans la province de Guizhou en Chine. Des minerais semblables ont déjà été traire pour Mo et Ni près de Dayong dans la province de Hunan. Dans ces deux régions minières, la minéralisation se présente dans le schiste argileux noir du Cambrien Inferieur (Formation Niutitang et équivalents stratigraphiques) sous forme de couche ou lentille unique de sulfures avec des épaisseurs exposées de plus de 15 cm et des épaisseurs rapport6es de plus de 35 cm. En plus des fortes teneurs en Mo (4%-7%), des échantillons du minerai contiennent jusqu’ à 7% de Ni, 2% de Zn, 2.5% d'As, et plusieurs centaines de ppb d'or et d'éléments du groupe du platine; toutefois, les métaux précieux n'ont jamais été récupérés des minerais. Des présences sporadiques sous forme de couches de minerai sulfure de Mo-Ni se retrouvent dans pas moins de cinq provinces s'etendant sur 1600 km de Yunnan a Zhijiang. Aucune de ces présences de minerais, sous forme de couches, ne semble associée a des roches du type mafique ou ultramafique. Des présences similaires contenant des teneurs élevées en Ni, Mo et EOP se retrouvent dans le schiste argileux noir Devonien du Yukon. L'exploration future pour des gisements de Pt, Au, Mo et Ni doit prendre en considération ce type de gisement encore inconnu précédemment."

Jan 1, 1992

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By J. Carr

This paper discusses: (1) the need for Western Canadian coal in eastern Ontario Hydro plants; (2) design parameters-unit trains, year- 'round receiving from trains, and shipping (Great Lakes season); (3) equipment chosen-dumper-indexer, outhaul conveyor, yard belt, stacker, reclaimer, surge-bin feeders, shiploader, docking system and dust control; (4) foundation and soil conditions-dumper house, yard belt, surge bin and dock-piling-runway; (5) winter conditions- thaw shed, feeder, lump breaker, beltings (oil), and dust control and disposal; and (6) operations to date.

Jan 1, 1979

By Robin Sheremeta

Fording Greenhills first acquired GPS (Global Positioning System) technology with the commissioning of a GPS-based dispatch system in December 1994. The second exposure to satellite technology came with the conversion of the conventional optical survey system to a high-resolution GPS system in June 1995. In September 1995,a GPS-based grade control system was tested on the largest shovel (Marion 301 — 58 cubic yard).In January 1996, the system was added to all of the cable shovels (2 P&H 2800s). All three applications of GPS at Greenhills are fully operational and producing positive results. This paper will focus on the practical application of GPS in a mining environment and the effect that GPS technology has had on the Greenhills Mine.

Jan 1, 1996

By W. R. Tyson

IT HAS BEEN KNOWN for many years that alloy steels can become brittle when tempered in the range of 350-600°C, or cooled slowly after heating to higher temperatures. The metallurgical literature reveals that blacksmiths were aware as early as 1883 that water quenching was necessary after heat treatment above 600°C to avoid brittleness. It has also been known for years that the problem is associated with trace impurities; a paper in the Journal of the Iron and Steel Institute of 1894 refers to the brittle, faceted fractures that occur in steels containing arsenic, phosphorus or sulphur. However, definitive investigation of the mechanism of embrittlement has been possible only within the last decade with the introduction of new experimental techniques to investigate surfaces, especially Auger electron spectroscopy. It is now possible to study in detail the chemistry of surfaces with a resolution of an atomic layer or two, and enormous progress has been made recently in studying the segregation of impurities to grain boundaries by exposing the boundaries by fracture inside the microscope. A clear picture of the processes occurring and their interpretation is now emerging, as was particularly clear at the recent 1977 ASM Materials Science Seminar on Interfacial Segregation held in Chicago in October. Recent research in this area has pointed the way for commercial exploitation of this new knowledge and experimental technology. It is the purpose of this article to trace progress in understanding temper embrittlement and to indicate other areas where control of interfacial segregation and its effects can be important in metallurgical applications.

Jan 1, 1978

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By Ian Orford, Ken L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper updates the principal author’s earlier publication, “Crushing Plant Design and Layout Considerations” (SME Mineral Processing Plant Design, Practise, and Control, 2002). It reviews the latest primary crushing and large cone crusher designs. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? The principal author’s previous paper in the year 2002 on ""Crushing Plant Design and Layout Considerations"" provided a detailed design and layout review for the design of primary and fine crushing (Secondary, Tertiary, Quaternary) mineral processing facilities. Some of the conclusions in this previous paper had predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available.The rock size reduction process, from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized into four (4) stages:• Stage 1: Mining ( Rock Breakage and Fragmentation)• Stage 2: Pre-Screening (Scalping)• Stage 3: Primary Crushing• Stage 4: Fine Crushing (Secondary, Tertiary and Quaternary; the crushers used in this stage are identified by the titles which usage has conferred on them)Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once a project's design criteria and the mine plan has been established, the actual circuit's utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stake holders in the selection of the final comminution circuit and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2016

By C. Y. Lim, H. W. Kim, M. S. Kim, J. H. Cho, Y. S. Lee

Al - 5.5 wt% Mg - 0.3 wt% Cu alloy strip was successfully fabricated by horizontal-type twinroll casting (TRC). For producing sound strips with no surface defect, the casting was conducted at various roll rotation speed, and the sound strip could be obtained at relatively low casting speed (3 rpm). The cast strip was homogenized at 450 °C for 10 hours, and then cold rolled with a reduction rate of 78%, followed by a final annealing at 450 °C for 1 hour. The annealed sheets showed good mechanical properties with approximately 330 MPa in tensile strength and 27 % in elongation, but exhibited strong anisotropy depending on the tensile directions. For the homogenized sheets, warm rolling was also conducted at 200, 300, and 400 °C. The tensile test results of the warm-rolled sheets showed that the rolling at medium temperature (300 °C) was proper to fabricate the sheets with relatively good mechanical properties and low anisotropy.

Jan 1, 2014

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008