Search Documents

By François Robert

The rate of new mineral discoveries in Canada has been declining in the last two decades. In response to the challenge and to stagnating investments in mining-related R&D, twenty Industry partners, supported by PDAC and Natural Resources Canada, established in 2010 the Exploration Innovation Consortium (EIC). This Consortium seeks to promote the discovery of new resources in Canada through coordination and sponsorship of industry-focused innovative and collaborative research and technology development, as well as training and education in mineral exploration. The two main themes of the integrated R&D program focus on exploration targeting in Deep and Mature Environments and in Remote and Covered Terranes.

May 1, 2011

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By T. J. Fee

Introduction The International Nickel Company have been pioneers in mine rescue work in Ontario. Following the fire in the Hollinger mine in the spring of 1928, the Company purchased ten self-contained oxygen breathing outfits, ten all-service gas masks, an oxygen high-pressure pump, life line, inhalator, ten cap-lamps with batteries, and a complete stock of spare and accessory parts. An instructor from the U.S. Bureau of Mines, Pittsburgh, came to the Creighton mine for one week and trained twenty men in the use and limitations of all equipment. Monthly training courses were commenced in the fall, and have continued to the present time. Of the original twenty men trained, ten are still on the Creighton mine rescue teams. In the meantime, and as an aftermath of the Hollinger fire, the Work-men's Compensation Board of Ontario and the Ontario Department of Mines established a central mine rescue station at Timmins. This was completed in the spring of 1930. It was then decided, in view of the great expansion in mine development in the Sudbury district, to build and equip a similar station to serve all the mines there, namely, Creighton, Frood, Garson, Falconbridge, Sudbury Basin, and Errington. An extensive survey was made and a central location selected opposite the Frood mine. The International Nickel Company donated a site, and the station was completed in the fall of 1930. The station is a two-storey brick building, 27 ft. by 47 ft., with a large garage adjoining it. The ground floor is used for equipment and for training the crews. On the second floor are living quarters for the superintendent and his family. The garage houses a closed truck, in which all necessary equipment can be taken to any desired point for training purposes or for actual mine rescue work, if and when necessary. The garage is also used as a gas room, where the men are trained in an irrespirable atmosphere. A gas-tight observation window between it and the training room enables the superintendent to see and direct the men undergoing training, weight exercisers and other devices being used.

Jan 1, 1935

By Hugh S. Spence

This paper deals with an occurrence of radium ore near Wilberforce, Haliburton county, Ontario, upon which development work has recently been undertaken and which seems more likely to prove of commercial grade than any other deposit' of radioactive minerals hitherto found in Canada. This occurrence is sometimes called the Richardson property, after Mr. W. M. Richardson, the discoverer, and will be so referred to in the present paper. Occurrences of radioactive minerals are not uncommon in eastern Canada, and a number are recorded in the literature. The earliest of such references is probably that in Geology of Canada, 1863, where is mentioned an occurrence of uraninite at Mamainse, on the east shore of lake Superior. The mineral was first described by J. L. Leconte, in 1847, under the name of coracite, and was said to occur in a two-inch vein at the contact of trap and syenite. Search for this locality in recent years has proved unsuccessful. Obalski, in 1894, mentions (1) the occurrence of uraninite at a mica mine near Murray Bay, Que. In 1903, Obalski records (2) tests made on this uraninite by Rutherford and the Curies and the determination in it of the then newly-discovered element radium. In 1901, he mentions (3) the occurrence of uraninite at the Villeneuve mica mine, on the Lievre river, and of samarskite at the Maisonneuve mica mine, in Berthier county.

Jan 1, 1930

By B. Arlyuk

The complex system has been developed for long-term assessment of world prices and sale volume of primary aluminium when using the analytical model of the market and market supply forecasts as well as economy development in the Western countries characterized by the industrial production indices as correct data of Western World aluminium consumption are absent, The important part of this system is the model developed for forecasting the degree of capacities utilization of smelters and refineries depending on the price level, The model contains a statistic part corresponding to the capacities distribution by the production cost, and a dynamic part determining the deviation from the static depending on the price variation dynamics, The developed complex system has been identified by the actual data of the world prices of smelter grade alumina and primary aluminium, conservation and reactivation of refineries and smelters in the Western countries within the period from 1992 to 2003. The system was used for primary aluminium and alumina price forecasts till 2020.

Jan 1, 2004

By D. S. Flett

"The current state-of-the-art of chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is reviewed. General considerations regarding the various flowsheet steps are examined and options discussed. Then, individual flowsheets are presented and discussed. Finally, the forward prospects for chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is considered and conclusions drawn concerning the likely application of this technology in the future. IntroductionHydrometallurgical processes for treating sulphide concentrates, in general, have received considerable attention over the last three decades or more. Many flowsheets have been developed, many pilot-plant studies have been undertaken and several processes are now successfully operating. For example, direct ammoniacal pressure leaching has been used by Sherritt Gordon Mines since the 1950s to extract nickel from pentlandite concentrates, the roast-leach-electrowin route is widely used to recover zinc from sphalerite concentrates and direct sulphuric acid pressure leaching of sphalerite concentrates has been successfully commercialized. Also, Duval Corporation operated a direct cupric/ferric chloride leaching process (Schweitzer and Livingston, 1982) with electrowinning to recover copper from chalcopyrite concentrates, this process (now closed) being the only chloride process which has been commercialized for a sulphide flotation concentrate. Despite these developments, it has long been considered, particularly for copper sulphide concentrates, that direct hydrometallurgical processes are in the main unlikely to be able to compete successfully with smelting for large-scale operations of simple high-grade single metal concentrates. As long as such concentrates can be produced commercially, smelting is likely to remain the principal processing route (Flett, 1981). This view is being challenged nowadays through pressure leaching developments made by Dynatec and CESL in Canada and the recent start-up of the Western Metals Gunpowder plant at Mt. Gordon in Queensland (Flett, 2000). Complex sulphide ores offer even greater opportunities because of the ability to produce a bulk sulphide concentrate from the complex sulphide ore with considerably higher metal recovery than is often possible from the production of individual metal sulphide concentrates from differential flotation. Interest continues to focus on hydrometallurgical solutions to these processing problems, particularly with regard to chloride hydrometallurgy. This paper, therefore, reviews current state-of-theart with respect to chloride hydrometallurgy"

Jan 1, 2002

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"Abstract — The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units. © 2012 Canadian Institute of Mining, Metallurgy and Petroleum. All rights reserved."

Jan 1, 2012

By A. Ignatieff

"A practical picture of the effects of stress and of the structural environment in an extraction area in a bedded deposit is described, and the main factors of ground control where principles of rock mechanics can be applied are discussed. Reference is made to early work in Europe, where systematic rock mechanics studies started in coal mines, as well as to the early work in the Canadian coal mines.During the past two decades, considerable theoretical and experimental knowledge, pursued both in the laboratory and in the field, has accumulated throughout the world, but the state of the science still does not permit application of substantiated theory such as is found in the design of above-ground structures, largely because of the complexity of the rocks. The mining engineer, as oppm1ed to the civil engineer, is constantly faced by exposures of new ground that is often subject to unpredictable discontinuities. However, the rationale already developed by rock mechanics principles and experimentation provides concepts and information that may be useful in selecting mining layouts. These concepts and existing measuring techniques can also assist ground control as mining progresses.Many of the bedded deposits, much as coals and evaporites, have pronounced deformation properties, and there are limitations in making stress measurements within short distances of mine openings or extraction areas. On the other hand, the measurement of movement of the hanging wall (roof) and footwall (floor) of roadways and extraction faces, as well as the sides of pillars, provides a most useful tool in assessing ground stability.This paper is to be regarded as a brief progress report with particular reference to Canadian applications of rock mechanics to bedded deposits."

Jan 1, 1968

By H. Oterdoom, S. Pilger, T. P. Bui, J. Rotarius

"Most FeNi furnaces used to rely on post-combustion and off-gas cooling inside the furnace to eliminate the produced CO gas, and control the off gas temperature. As furnace load, capacity, and thus gas volumes increased over the years, this led to increased instabilities that can cause problems in controlling the operation. Some of the large capacity furnaces nowadays work with partial or full combustion outside the furnace, more similar to the steel industry. Forced combustion with or without enriched air and other additions can support in controlling post-combustion, stabilizing and even reducing off gas amounts, and affecting composition. This paper presents some of the possibilities and advantages of having a specially designed post-combustion system for the FeNi laterite industry, but that could also be applied to other processes as well.Large Scale Furnaces In the FeNi industry, the Rotary Kiln Electric Furnace (RKEF) process is still going strong in spite of continuous hope that hydrometallurgical processes will one day make the RKEF plant obsolete. Within the pyrometallurgical plants there is a continuous trend for larger scale furnaces. The development for a number of furnaces that were started before 1985 and increased capacity by “natural growth” is given in Figure 1. Natural growth refers to the development of the plants that after having mastered a certain level of operation, were ready for a higher load that could be installed either with a new furnace on the same site, or during a revamp. The advantages of natural growth are numerous, for example: •,Deep knowledge of the ore and its’ behavior, no need for testing, and little risk of surprises. •,Mining, laboratory, equipment, etc. is all proven technology for the conditions on site. •,Starting a furnace with increased capacity is a re-start, not a green-field commissioning. •,Typically, when increasing the production capacity of an existing plant, not the entire plant is commissioned for the first time, but only a part. In the FeNi laterite industry for example, the kilns may already have had the capacity to provide enough material."

Jan 1, 2017

By John Canterford

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15,000 t/a magnesium alloy production facility in Nanjing, China, Site construction commenced in February 2005 with installation of all major components completed by the end of October 2005, Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005, Since that time ramp-up to the name plate capacity has been undertaken, This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By Sami Hindstrom, Travis Orser, John Starkey

"A great deal of effort has been expended in the last 11 years by the authors and others to identify the correct power required to grind ore in a SAG mill, by developing ore hardness variability functions for the ore body to be mined. This paper describes the next step in the SAG design process, which is choosing a SAG mill to accomplish the required specified design performance.At the test work stage, each ore hardness data point is a unique and discreet bit of information that represents the energy required to grind the ore represented by that sample at optimum SAG conditions. When the design criteria are set, it is now considered necessary that the required power draw in the mill chosen be provided at optimum conditions as well.Based on actual 3-ft diameter pilot plant results, we can now show that the grinding efficiency and throughput drop when the optimum load limit is exceeded. Future work is expected to show a similar reduction in efficiency when exceeding optimum speed. Providing specified power by exceeding these optimum conditions is not adequate and leads to a lower cost but underperforming SAG mill.It is possible in some cases to modify a SAG circuit to force it to perform better, but this often takes time, much effort and costly modifications. In most cases the capital spent on a properly sized SAG mill may prevent production losses that would be many times greater over the extended start up period. This is the direct result of choosing the proper SAG mill at the start.INTRODUCTIONThe sequential steps required for the design of any grinding circuit, have changed dramatically in the last seven years. Previously, it was considered necessary to do six foot diameter SAG mill pilot plant tests on representative samples of minus six inch ore (F80), in order to understand design requirements. It can now be shown that this method is costly and not likely to produce the desired result because it is difficult to recover six-inch material from deep within a new mine. The representative nature of the sample is often compromised when the sample is selected."

Jan 1, 2003

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By Y. Gordon

ABSTRACT A methodology based on a two-stage approach was developed for process technology selection. The first stage includes evaluation of available technologies, followed by shortlisting the best technologies based on mass and energy balance modelling, financial analysis, and risk analysis. The second stage involves detailed analysis using refined input data, mass and energy balance modelling, and capital and operating cost estimation, as well as a more detailed financial analysis. A case study covering the selection of ironmaking technologies for a company in the Russian Federation is presented to illustrate the critical elements of the methodology and the analysis process.

Jan 1, 2014

By H. C. Gunning

In spite of the fact that mining has been more or less active in the northern part of Vancouver island since the late 'nineties', there seems to be a remarkable lack of information regarding the nature and development of the region. Recently the operations at the Old Sport mine of the Coast Copper Company, Limited, and spectacular copper discoveries in the vicinity of Nimpkish lake, have directed the attention of the mining fraternity to the district. The writer spent the summer of 1929 making a reconnaissance examination of the general geology and mining properties of the area between Quatsino sound and Nimpkish lake, and he feels that a short paper describing the nature and mining possibilities of the region should be of interest at this time. A more detailed account of the ?geology and of the mining properties will be published in the forth- coming Summary Report of the Geological Survey. A short paper dealing with the Nimpkish Lake district was presented at the Annual Meeting of the British Columbia Division, held recently in Vancouver.

Jan 1, 1930

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability. The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employes to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed."

Jan 1, 2002

By M. L. McAllister, M. Veiga

The mineral industry has seen many significant changes in the past decade. Increasingly, it has responded to unanticipated pressures and demands with a variety of voluntary initiatives. Yet there is still much to do. Mining now takes place in a different context than was the case in the past. Socio-economic, political and environmental considerations must now be integrated into traditional mining systems. This process of integration needs to involve industry, governments, academics, communities and other stakeholders to design a new approach to mining, one that can be fostered through interdisciplinary links and holistic strategies. This paper considers the meaning of sustainability in the context of the Canadian mining industry and explores the need for a broader vision for the mining industry. The role of technology is then analyzed and related to an initiative recently taken by Canadian universities to develop a national network for interdisciplinary research into sustainable mining, CaSM.

Jan 1, 1999

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d'Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack 'of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By Michel Rodrigue, Sylvain Duchesne, Louis Racine

"LocationThe Louvicourt mine is located 20 km east of Val d'Or in Abitibi, in the northwest part of the province of Quebec. The mine is located on Highway 117 connecting Val d'Or to Montreal and very close to the main railway networkHistoryFive successive exploration attempts by Aur Resources resulted in the discovery of the large Louvicourt orebody in June 1989. Construction of the surface and underground infrastructures commenced in the spring of 1991. Milling operations commenced in July 1994. The entire project cost CDN$290 million, almost CDN$20 million less than initially estimated. The concentrator infrastructure cost CDN$64 million.Louvicourt mine is owned in partnership by Novicourt Inc. (45%), Teck Corporation (25%), and Aur Resources Inc., the administrator (30%).Brief DescriptionLouvicourt mine is the largest producer of base metals (Cu and Zn) in Abitibi-Temiscamingue. Its average daily production is nearly 4300 t of ore, for an annual production of 200 000 t of copper concentrate (28% Cu) and 33 000 t of zinc concentrate (57% Zn). After only a few weeks of operation, it had attained its objectives for the most part, and operations continue to be improved."

Jan 1, 2000