Search Documents

By Ryan W. Ulansky

This paper presents the conceptual design of a magnetically-levitated skip for use in an underground mine. A skip is used to move rock from an underground mine to its surface processing facility. Conventionally the skip is raised and lowered by cables, similar to an elevator. In a magnetically-levitated skip, the cable is replaced with a linear induction or synchronous motor to provide propulsion and levitation. Removal of the cables in a magnetically-levitated skip provides many advantages over a conventional system including the ability: to negotiate corners, to travel vertically in the shaft as well as horizontally to the mining face, and to move a very large volume of material using multiple skips in a small shaft. A magnetically-levitated skip is a safer, more environmentally-friendly, productive alternative to conventional skipping. It has the further advantage to decrease haulage distances for underground vehicles.

May 1, 2002

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011

By J. R. Goode

"Coarse ore sorting is here defined as the physical separation of a mixture of coarse (+3/8 inch) ore particles into two or more separate groups of total value greater than that of the unsorted ore. An ore will probably be sortable if the geology of the orebody and the mining practices employed meet conditions outlined in this paper.The paper points out how sorting can substantially reduce tonnage variable operating costs because sorting can double the mill head grade of amenable ores by rejecting waste rock from the mine output. The effect of sorting on ore reserves is outlined. It is also suggested that sorting is a low cost alternative to conventional expansion.The mode of operation of the Ore Sorters Kadel 13 Photometric and MK VI A Radiometric sorters is detailed. The report concludes with detailed descriptions of the photometric sorting plant operated by the Doornfontein Gold Mining Company is South Africa and the Radiometric Sorting Plant presently under construction at the Schwartzwalder mine of Cotter Corporation in Colorado."

Jan 1, 1975

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre's (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

By Dina M. Aloi

In today?s evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to ?engage? communities without a clear understanding of ?how? to do this or to what end. This move, away from compliance, develops more of a focus on ?Community? Social Responsibility and sustainability. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of ?engaging? communities in mining project design and development leads to a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be ?engaged? in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this ?engagement? and manage this risk will be discussed.

May 1, 2007

By Roxanne Scott

Outline ? Overview of Community Investment in the Mining Sector ? Emerging Good Practice: ?Strategic Integrated Community Investment? ? Assessing Local Context: ? Institutional Assessment ? Partnership Assessment Approaches to Community Investment Isolation: No proactive engagement in community development Ad hoc philanthropy: small infrastructure, sponsorships, donations Strategic philanthropy: Community proposes options for development Company decides what to do and carries it out, e.g. building schools, health posts, roads Strategic integrated community investment: ? Aligned with government/community development goals and priorities ? Communities and government involved in decisions and execution ? Focused on training and capacity building ? Partnerships ? Continuation in absence of company support Measured returns on investment

May 1, 2010

By V. I. Lakshmanan

Process Research ORTECH Inc. (PRO), with its in-depth knowledge on cobalt behaviour in nickel matte smelters and its novel mixed chloride hydrometallurgical processing, is developing a hybrid process to enhance cobalt recovery. PRO’s experimental data is compared with plant information on cobalt behaviour in smelters. In final stages of iron rejection in the converters, the thermodynamics of the matte-slag system dictates the undesirable transfer of the cobalt to the final converter slags. This results in much lower cobalt recovery in the product Copper/Nickel matte (<60%) in present copper and nickel smelters. This information is used to transfer cobalt into desired quantity of converter slag. The enriched cobalt slag is subjected to PRO mixed chloride process to recover nickel, and cobalt as high value salts of importance in lithium ion batteries. From a typical converter slag containing 3.5% Ni, 1.5% Co, and 1.0% Cu, PRO leach process extracts 98 % Ni, and 98 % Co, and 99% Cu. Application of this process to enhance cobalt recovery in typical Copper/Nickel smelters is presented. In addition, this will also enhance the Copper and Nickel recovery. Both these aspects are of interest to the Copper, Nickel, and cobalt producers. INTRODUCTION In pyrometallurgical extraction of copper and nickel from sulphide ores cobalt often occurs with copper and nickel. The requirement of cobalt is increasing due to its need in lithium ion cells used in electric vehicles. Therefore its efficient and economical extraction in a form suitable for use in lithium batteries is of great interest at present. In the pyrometallurgical processing of copper and nickel sulphide concentrates the concentrate is smelted to produce a furnace matte, which is then sent for converting to remove the iron to produce iron free (~1% Fe) matte for further processing to copper or nickel matte. The copper/nickel matte is processed for metals recovery by hydrometallurgical or vapo-metallurgical or oxidation – reduction routes to make market products. As shown in Figures 1 and 2 the slags are produced in the smelting step and in the converting steps. The metal losses in smelting are controlled by the oxygen pressure in that step and slag production which is controlled by concentrate grade. The slag produced in the converting step which is carried out at a higher oxygen pressure contains higher level of metals is often returned to the smelting step to increase value metals recovery.

Jan 1, 2019

By A S. Leitch

This paper is based on the accident prevention pro-gram carried out in the coal mines of Alberta. It defines the role of the Alberta Mines Branch and of The Work-men&apos;s Compensation Board, and relates how a safety pro-gram was initiated. The formation of the Alberta Class 1 Mining Safety Council is also described. The responsibilities of both management and the individual worker are then outlined, and the main features of a successful accident prevention program are delineated. T HE purpose of this paper is not to repeat generalities and platitudes about industrial safety, but rather to relate the experience of Alberta coal mines during the past number of years in their efforts to keep accidents to a minimum. It has been learned from experience that many basic principles are as sound today as they were 20 years ago. How-ever the complexities of modern mining methods and the modern man or miner have created problems that did not exist then.

Jan 1, 1964

By Gordon F. Scott

This paper considers a recently completed hoist project for IAMGOLD. Called the Westwood project, this mine utilises some of the largest drum hoists supplied to the North American Market in recent times. This project is an example of where many of the design features discussed the associated paper, (Robotham, 2011) were incorporated. Director of sales and marketing, Gordon Scott has worked at DavyMarkham for over 30 years in a variety of roles starting as a mechanical design engineer, moving to project management before joining the sales department. Gordon has an honours degree in mechanical engineering from Leeds University.

May 1, 2011

By Paul Armstrong

THE first discovery of lead and zinc ore on Calumet island was made in 1893 by John Lawn, who then staked a portion of the property now owned by Calumet Mines, Limited. His discovery was developed by James and Calvin Russell, who are said to have shipped a few tons of sorted ore, averaging 39 per cent zinc, 13 per cent lead, and 11 oz. silver per ton. In 1898, the property was being operated by the Grand Calumet Mining Company, who mined and shipped, for treatment in a Belgian smelter, 1,100 tons of ore averaging 32 per cent zinc, 9 per cent lead, and an unreported content of gold and silver. After some indecisive exploration by an American syndicate in 1907, the property lay idle until1910, when the Calumet Metals Company-later reorganized as the Calumet Zinc and Lead Company-re-commenced exploration. After sinking an 85-foot shaft-the McDonald shaft-and doing a few hundred feet of drifting and cross-cutting, this Company, in 1912, erected a 150-ton daily capacity gravity-concentration plant, in which some 800 tons of ore, mined from the McDonald shaft and Bowie pit, were milled. Owing to very disappointing mill recoveries, the property was shut clown and-after several years of idleness-in? 1916 the mill and mining plant were destroyed by fire and the Company went into bankruptcy. In 1918, an unknown operator shipped to an Omaha, Nebraska, smelter 22 tons of ore, probably sorted from the dumps of the Ste. Anne shaft and Galena pits, averaging 44 percent lead, and 0.26 oz. gold and 61 oz. silver per ton. The British Metals Corporation (Canada), Limited, in 1926, optioned the property. They unwatered the McDonald shaft and, after doing an additional 300 feet of cross-cutting and drifting on the 85-ft. level, estimated there were some 33,000 tons of ore between this level and the surface. Surface exploration, including trenching, on other showings on the property gave discouraging results and the option was dropped.

Jan 1, 1941

By W. A. Ahrens, J. H. McNamara, J. G. Franek

"An economical, pollution-free process has been developed for the hydrometallurgical extraction of copper from sulphide ores. The extracted copper, in the form of cuprous chloride (CuC/), is converted by reduction to copper metal. The metal is melted and fire -refined into wire bars which meet the standards of electrolytic tough pitch (ETP) copper wirebars. IntroductionThe successful development of the Cyprus Copper Process has been an evolutionary series of events covering a time span of some nine years. The original process, based on an electrolytic membrane cell principle , was abandoned in 1975 because of technical, economic and pollution problems. During the past four years, the pilot plant has been reconstructed based on a new flowsheet and operated successfully in several campaigns, some for as long as four months. The pilot-plant hydro section operates at a 225-lblhr copper rate. In October 1977, a feasibility study was completed by Jacobs Engineering, Pasadena, California. The study showed favourable economic and technical feasibility. Jacob&apos;s studies in 1978-79 revealed favourable comparative economics with other known pyrohydro processes and favourable economies of scale.The Cyprus Copper Process converts copper concentrates of varying composition into copper metal, which has been proven to be equivalent in every way to electrolytic tough pitch copper, suitable for electrical applications. This is accomplished at capital and operating costs which are estimated to be lower than those associated with any other known currently applicable technology. Also, the total energy requirement is equal to or less than any other known process and the process is essentially pollution free."

Jan 1, 1980

By M. Sturzenegger

This paper documents a field survey using long-range terrestrial digital photogrammetry at the Palabora open-pit mine, South Africa, for multi-scale characterization of rock mass discontinuities. Stereomodels covering the entire mine were generated based on photographs taken from a distance of 1600m across the pit, using a series of f=20-400mm lenses. Details on the methodology used and its accuracy are discussed. Preliminary results on discontinuity orientation, persistence and intensity are presented, highlighting the effect of observation scale. The potential uses of long-range terrestrial digital photogrammetry in open-pit mine and large natural rock slope environments is emphasized. The use of an f=400mm lens from distances larger than 1.5km may represent an important step forward in the geotechnical characterization of inaccessible remote rock faces.

May 1, 2009

By Rodney R. Koch

The phys ica l properties of gold should faci li tate its detection. However, the average concentration of gold in the ea rth's cru st precl udes the ability of geophys ical methods to detect the metal directly. In order to effectively pursue geophys ical detection and location of gold mineralization there must also be geological input - i.e. a model. This will lead to the selection of the appropriate geophy ical techn ique(s) in the fo llow-up programs. Interpretation of the fie ld survey data is of con iderable importance in expl oration geophys ics. Analytical techniques such as cont inuation, fi ltering, and spectral analys is, are now routinely empl oyed in the analys is of survey data to aid the interpretation process. The uccessful application of geophysical methods and the use processing techniques is demonstrated by two recent Saskatchewan discoveries. The first, the Star Lake 21 Zone, with reserves of 230,000 tons grading bener than 17.14 git Au associated with a disseminated sulphide quartz-bearing shear zone yielded geophysical anomalies that were distinctive, obvious, and would have lead directly to its discovery. The econd , the Laurel Lake Prospect, with ore grade intersections of 28.0I git Au and 52 .46 git Ag· over 5.49 m, resulted in numerous geophysical anomalies. However, none of these anomalies demonstrated association with the mineralization until processed results indicated that structural features crosscuning regional trends were important cont rol mechanisms for the mineral ization.

Jan 1, 1986

By R. W. Lawrence, J. B. Austin, P. B. Marchant, J. T. Chapman

"Biohydrometallurgy is the use of microbiological reactions to assist in the extraction of metals. Bioleaching offers an innovative alternative for the treatment of refractory gold-bearing sulphides (1). One particular cost advantage of bioleaching is the potential to enhance gold extraction after only partial sulphide oxidation. The apparent selective sulphide oxidation is more prevalent where the refractory gold is associated with arsenic and antimony (2). Oxidation of the pyrite minerals and arsenopyrite at different oxidation rates can result in high gold extractions at relatively low levels of sulphide oxidation due to preferential, or selective, oxidation of the arsenic mineral. Arsenic extraction rates in a bioleach process typically exceed the iron extraction rate. Therefore, in concentrates in which the precious metals are principally associated with arsenic minerals, liberation of the precious metals may be possible with high recoveries and less than complete sulphide oxidation. The capital and operating cost advantages of partial sulphide oxidation are inherently obvious and are briefly illustrated herein.Ultra fine milling (UFM) is another alternative for enhancing gold extraction from refractory sulphides. Some refractory gold is simply particle size sensitive and UFM can improve gold extraction without the need for costly sulphide oxidation (3). Fine grinding technology for enhanced gold recovery developed by Metprotech, South Africa, is currently producing 2 - 4 micron ground product using a single pass, stirred ball mill. Proper application engineering has ensured that plug flow occurs through the mill. Plug flow from the feed inlet at the bottom of the reactor ensures that short circuiting of feed does not occur and as a result, the mill product does not require classification.A combination of UFM as a pretreatment for bioleaching could provide a mechanism for enhanced selective sulphide biooxidation and/or increased overall gold extraction following biooxidation due to improved particle liberation ( 4). The effect of UFM on biooxidation costs will be discussed. Only sulphide concentrates are considered herein for application of UFM in combination with biooxidation."

Jan 1, 1990

By P. D. R. Maltby

"With the narrow vein structure of Nova Scotia gold deposits, selective mining is rarely possible and mill heads will be too low (below 0.10 oz per ton of gold) to support a conventional mill of up to 1000 ton per day capacity at present gold prices. The recent operation of a small 100 t.p.d. mill at Cochrane Hill using fine grinding - leaching - filtration supported this assertion. Milling costs exceeded $25.00/ton of feed mainly due to high capital, labour and maintenance costs.Accordingly, since 1981, efforts have been directed towards the development of a cheap gold extraction process in terms of both capital and operating costs. The main criteria is to produce gold below US $200 per oz including all administration, mining and process stages. This paper describes such a process development for Cochrane Hill. LOCATION AND HISTORY OF THE PROPERTYThe Cochrane Hill property is located about 8 miles North of Sherbrooke, N.S. on highway No. 7. Sherbrooke is about 180 miles east of Halifax. Gold was originally discovered at Cochrane Hill in the 1860's. Early work consisted of trenching. In the 1930's a small shaft was sunk to about 80 feet and some tonnage treated using a stamp mill with gravity concentration of gold.Northumberland Mines Ltd. acquired a 70% interest in the property in 1977. Subsequent drilling indicated a potential zone of gold mineralization with a drill-indicated tonnage of one million tons having a grade of 0.07 ounces per ton of gold (all high assays cut to 1 oz) down to a depth of 300 feet recoverable by open pit mining methods. In broad terms, the goldbearing zone is about 50 feet wide and 800 feet long and dips at about 70°."

Jan 1, 1984

By W. E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential."

Jan 1, 2002

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985

By Hua-Zhong Yu

Gold is one of the most widely used substrate materials for self-assembly. Self-assembled monolayers (SAMs) prepared from alkanethiols and their derivatives on gold are the most reliable and well-studied systems to date, which have attracted much attention because of interest in two-dimensional molecular assemblies, and of their potential applications in molecular devices, sensors, and functionalized interfaces. Gold electrodes are also very important in microelectronics and electroanalytical chemistry. This work reports the characterization of a new type of gold substrates for self-assembly. The gold substrates are constructed from recordable compact disks (R-CDs) with simple and straightforward wet-chemical treatment, and can be made at desired sizes and shapes that satisfy different experimental needs. In particular, an easy, inexpensive, and reproducible method to prepare self-assembled monolayers (SAMs) on CD-R gold substrates after removing the protective polymer films with concentrated nitric acid was described.

Oct 1, 2003

By Daniel D. M. Adams

Over the last 100 years industry in general has been trying to advance the ability to maintain systems through management processes. Mining has looked to utilize onboard data systems in our mobile mining fleets to compliment these processes. Combining the two concepts build the concept that Rio Tinto refers to as asset health. These programs can generate a cost shift between $20,000 and $100,000 per piece of equipment annually. Even with the documented savings many operations struggle to justify the systems, why?

May 1, 2011

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985