Search Documents

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By Don Thompson

Canada’s oil sands are a controversial topic and virtually every newsmaker and layperson seems to have an opinion about this 179 billion barrel resource. The oil sands represent 97 per cent of Canada’s remaining oil reserves, but misinterpretation and misrepresentation of the facts are threatening development of a resource that generates significant employment and tax revenue for Canadians. Join Don Thompson, president of the Oil Sands Developers Group, as he dispels the top ten myths about Canada’s oil sands and presents an alternative perspective on an industry that can play a critical role in North America’s economic recovery.

Jan 1, 2010

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By Michael Drozd

"The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application.The unit operations are:a. Absorptionb. Desorption (Stripping)c. Acid Washingd. Reactivatione. Carbon Handling (carbon transportation, sizing, dewatering, etc.)Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. These parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability.Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operations in the United States have undertaken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPLCarbon Link is being used to attempt to fashion industry standards so that a common reference point can be established for activated charcoal usage."

Jan 1, 2008

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989

By Dave Bulled, Khiratt Husain

"The use of High Pressure Grinding Rolls is gaining significant interest as a replacement for SAG milling in the comminution of hard rock ores because of the potential for reduced costs in terms of energy and grinding ball consumption. Estimation of expected energy consumption for fullscale operations has conventionally involved the testing of a few fairly large samples in pilot scale HPGRs. This paper describes the development of a small-scale batch test method for determining a work index for HPGR of a large number of samples that can be used to show the variability of the ore as an integral part of a geometallurgical approach to circuit design and production forecasting.The test equipment that was developed comprises a hydraulic press with adjustable pressure operating on small batches of ore in a locked cycle test procedure. A work index measurement was determined that links the specific energy consumed in the test to the breakage achieved such that the index can be used to predict comminution energy requirements.The measurements were calibrated against laboratory scale HPGR equipment to develop a model for design and forecasting that includes crushers, HPGRs and ball mills in a complete comminution circuit.INTRODUCTIONEstimation of the expected energy consumption for full-scale HPGR operations has conventionally involved the testing of a few fairly large samples in laboratory and pilot scale machines (Danilkewich, 2006). With the financial input of five mining corporations, SGS Lakefield Research has developed a small scale test capable of providing relevant information on the variability of energy consumption and size reduction from drill core samples. It is our intention that the values measured in the test will be scaled up, through benchmark comparison with pilot sized and full sized HPGR units, to allow plant design and throughput forecast on a block by block basis of the mine plan using a new CEET program. CEET® (an acronym for Comminution Economic Evaluation Tool) is an advanced grinding design and performance predicting tool that uses energy relationships to model the performance of SAG / Ball mill circuits."

Jan 1, 2008

By C. C. Walden, A. Bruynesteyn

"Chemical and biological aspects of the formation of acidic effluents from sulfide waste materials are discussed. Test procedures to determine the acid producing potential of waste materials, as well as the characteristics of such acidic effluents, are presented. Practical applications of the test procedures are discussed with reference to predictior of environmentally unacceptable drainage and to estimation of metal recovery by dump leaching.INTRODUCTIONNatural leaching of sulfide minerals, exposed to the atmosphere, has been occurring for geological time. For centuries, man has been aware of the acid drainage originating from coal workings, copper mines and waste dumps. With the advent of the technical sciences, the processes involved in acid mine drainage production were considered to be solely chemical in nature. However, in 1947, it was shown (1) that a specific microorganism, called Thiobacillus ferrooxidans, was responsible for acid mine drainage from coal workings. It was demonstrated that under suitable conditions - this bacterium oxidized pyrite and marcosite in the coal to ferric sulfate and sulfuric acid. Numerous studies have subsequently demonstrated that - under suitable conditions - Thiobacillus ferrooxidans can attack most sulfide minerals, producing weak sulfuric acid, oxidizing ferrous to ferric iron and solubilizing other metals present (notably copper and zinc) as their sulfate salts."

Jan 1, 1980

By A. F. Banks

"Potash processing has much in common in terms of unit operations and plant operating strategy with other mineral processing plants. As it is a rather large topic the processes will be broad brushed to give you some background and then I will go into a little detail on the things we do in the Cominco plant that may be of interest to the group as a whole. In particular the centrallized computer control system and associated instrumentation and the operator training programs will be covered as well as the mill fire, something that could happen in any plant. THE ORE AND PRODUCTSThere are differences in potash ores as you would expect. It is my intention to deal with the ores processed in the Saskatoon area. These are mined from the beds in the Patience Lake Member and have a mineralogical description as follows:Sylvite (Potassium Chloride) 40%Halite (Sodium Chloride) 55%Insolubles (Slimes) 5%A number of products are made from this ore. It is characteristic of a potash plant that you put as much effort into grading and converting the sylvite to meet market requirements as you do in recovering it."

Jan 1, 1976

By Brad E. Melanson

Because mine haul trucks consume considerable quantities of fuel, they are ideal candidates for the adoption of cleaner and cheaper fuels like natural gas. Impressive fuel cost savings will be realized in regions where liquefied natural gas (LNG) has cost advantage to diesel fuel, while also providing significant reductions of air contaminants and greenhouse gases. High Pressure Direct Injection (HPDI) of natural gas utilizes the diesel cycle combustion process and therefore retains the diesel engine?s high performance and efficiency characteristics. HPDI has been demonstrated in on-road Class 8 trucks since 2001 accumulating almost 10 million kilometres to date. The supply of LNG fuel will be an essential parallel aspect in the introduction of HPDI to mining. LNG can be transported to site as diesel is today, or may be produced on or near mine operations that have access to methane sources or pipelines.

May 1, 2006

By Garry Johansen, Andrew McCallum, Sandy Gray, Gary Patrick, Jennifer Abols

"The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flowsheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit.The InLine Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size – saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements.When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores - some of which may not currently be economically feasible using standard processes and flowsheets. We have provided three examples of such projects, where an alternative to whole ore leach and CIP or CIL has delivered these benefits."

Jan 1, 2003

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By Roy T. Bowles

This paper focusses on technological developments which occurred in the village of Deloro, Ontario between 1868 and 1919. These developments illustrate the manner in which improved metallurgical processes linked Ontario mineral resources to industrial expansion. Overview of Deloro The village of Deloro is in Hastings county, about 5 miles from the village of Marmora, the site of the old Marmora iron works and the more recent Marmoraton iron mine. In this area, the Canadian Shield meets the Great Lakes lowlands. The first settlement in the vicinity occurred in the 1820s and was associated with the Marmora iron works. Settlement grew around agriculture. Gold was discovered in Hastings county in 1868. Deloro - the name derives from gold - developed as a concentrated settlement in proximity to several gold mines and the related processing activities. By 1901, substantial smelting works were successfully producing gold and arsenic from local ores. The village was developing as a company town within the framework of benevolent paternalism. For reasons associated with markets and with local ore supplies, the Deloro mills were idle for a period beginning in 1902. Developments in later periods connected Deloro to world events. In 1903, silver was discovered at Cobalt, Ontario. By 1907, M.J. O'Brien, who owned mines at Cobalt, had purchased the Deloro works and was using them to process Cobalt-area ores*.

Jan 1, 1999

By Mike Samuels, John Starkey

"This paper examines test results and grinding mill design for the recent Fortune Minerals’ NICO Project, located in the Northwest Territories. SAG milling and rod milling options are compared. Rod milling is clearly shown to be the best option because of the ore’s extreme resistance to breakage in a SAG mill environment.Surprisingly, the Bond Ball Mill Wi was 13 kWh/t for this ore. The Bond Rod Mill Wi was 20 kWh/t, whereas the SAG pinion energy to grind the ore to T80 1.7 mm was 30 kWh/t. The existence of ore with this ratio of SAG hardness to Bond BM Wi has not been previously observed. If not considered, this critical relationship may adversely impact the accuracy of mill design. This paper substantiates the significance of these findings to achieve successful grinding design on ore that is macro-competent during primary size reduction, but relatively normal during secondary grinding.INTRODUCTIONThe NICO Cobalt-Gold-Bismuth-Copper deposit is located 160 km northwest of the City of Yellowknife, Northwest Territories. It is the largest IOCG-type deposit (aka Olympic Dam-type) currently recognized in Canada with Mineral Reserves of 21.8 million tonnes contained within a larger 57 million tonne, lower-grade Mineral Resource. The project, owned 100% by Fortune Minerals Limited, has been assessed in a positive definitive feasibility study, subject to underground test mining and pilot plant testing, and is now in the permitting stage to develop a combined open pit and underground mine and process plant. An updated process flow sheet incorporates conventional crushing, grinding and bulk flotation, followed by filtration for shipment of a concentrate to a purpose-built refinery proposed to be built near Saskatoon, Saskatchewan. At the refinery, separate bismuth and cobalt concentrates will be produced following regrinding. The hydrometallurgical process methods include: pressure acid leach, precipitation, ion exchange, and electro-winning for recovery of cobalt as 99.8% cathode; solvent extraction and electro-winning of by-product copper cathode; ferric chloride leach and electro-winning for recovery of bismuth as 99.5% cathode; and cyanidation of the leach residues for recovery of gold as doré."

Jan 1, 2010

By S. Banisi, M. Poorkani, M. Farzaneh, M. Askari

"At the Sarcheshmeh copper mine 40,000 t of ore per day with an average grade of 0.9 % Cu is ground to 70% passing 75 microns. Grinding is effected in 8 parallel lines of 8 x 5 m ball mills in a closed circuit with cyclones. The make-up balls are 80-mm forged alloy steel balls and the average ball consumption is 750 gh of ore ground. In order to optimize ball size distribution inside the mill, based on the previous investigation instead of using only 80 mm make-up balls a combination of 80 and 60 mm (75% to 25% by weight) ball charge was used in one of the mills. To evaluate the performance of three ball types namely forged alloy steel balls (A), ductile cast iron (C), high chromium cast iron (D) and also a combined (80 and 60 mm) charge of forged alloy steel balls (B), four identical parallel mills were charged accordingly. These four mills were sampled during a period of six months. The amount of material finer than 75 microns of cyclone overflows was selected as a criterion for the performance evaluation. It was observed that in a mill with the combined make-up balls the amount of fine produced was 4% higher than the other mills. The consumption of ball types A, C and D were 730, 710 and 534 g/t, respectively. The results of laboratory flotation tests showed that due to an improvement in the production of fines an increase of 1.4% in the overall copper recovery is obtainable. Due to the promising results, the new make-up ball regime was implemented in all mills in the plant.INTRODUCTIONThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and has been processing 40,000 t/d of ore since 1982. The mine produces 100,000 tonnes of copper and 2,200 tonnes of molybednite concentrate per year. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailing constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83 and 87 % depending on the operating conditions and ore type."

Jan 1, 2002

By J. L. Bowlby

The heats of combustion of fuels are determined in the laboratory by means of a calorimeter, usually of the oxygen bomb type. A known weight of the fuel is burned in an atmosphere of oxygen under approximately 400 pounds pressure in a heavy metal container-the bomb- and the heat evolved is imparted to a definite quantity of water. From the rise in temperature, measured by means of a Beckmann thermometer, and other data incidental to the determination, the heat value of the sample can be calculated. On paper, the method appears simple indeed, but in practice the determination of the heat of combustion is one of the most difficult of the various coal analyses. This h as led to considerable investigational work in order to obtain formula: whereby calorific values of solid fuels could be calculated from proximate analysis data al one. The proximate analysis of a fuel consists of the determination of moisture, ash, and volatile matter, with fixed carbon by difference. Sulphur determinations properly belong to the ultimate analysis, but in this section of the country, where the sulphur content of the coal is comparatively high, a request for the proximate analysis of a fuel implies the determination of the sulphur as well.

Jan 1, 1929

By C. George Miller

"As the influence of governments has become more widely felt, the use of research techniques to analyze policy has increased. Mineral economics, as one of the foundations of mineral policy research, has grown accordingly. Policy research and analysis has been carried out within governments, university departments and the private sector. Each of these institutional environments has characteristics which influence the topics of study, the approach, the methodology and the output of the research. A brief survey of recent research activities provides illustrations of trends and developments occurring within this organizational framework.A radically different organization, the independent research institute, has begun to make an impact on policy research in recent years, and will have an increasing importance in the future. Combining certain features of the traditional research organizations, it nevertheless has important differences which are essential to its effective functioning. An overview of the formation, goals, organization and operation of one such institute is presented."

Jan 1, 1976