Search Documents

By Moore R

An intensive safety campaign at Mount Isa Mines Limited from 1956 to 1966 saw the lost time accident frequency rate fall to half its original level. A review of the safety programme was carried out in 1967 and in 1968 the Five Point Safety System was introduced. The seven years since its introduction have been years of significant achievement both in production and safety. Improving safety is a fundamental part of Mount Isa Mines Limited's policy and this system has been a major tool in implementing that policy. To be successful personnel need to be prepared and trained for its introduction and subsequently counselled on its use. A carefully prepared programme is required to phase in various aspects of the system and to make use of complementary steps. The system has been a success and it is anticipated that the continued drive to improve the use of principles of the system will further improve safety. It is hoped that this paper will be of value to those personnel concerned with industrial safety in Australia.

Jan 1, 1975

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

Electrochemical investigations of the flotation of sulphide minerals are re- viewed. Flotation with thiol collectors is interpreted in terms of a "mixed poten- tial" model in which the process leading to hydrophobicity is the anodic oxidation of the collector at the mineral surface and this is driven by the cathodic reduc- tion of oxygen. Electrochemical studies have identified the products of anodic oxidation as chemisorbed collector, metal collector compounds, and dithiolates; the products formed in each situation depend on the collector used, the mineral under study, and the pretreatment of the mineral surface. Investigations on galena, pyrite, and chalcocite are discussed. Electrochemical and x-ray photoelectron spectroscopic studies have been used to determine the products of surface oxi- dation of sulphide minerals in order to elucidate the mechanism of collectorless flotation. The mixed potential mechanism allows consideration to be made of the ways in which flotation of sulphides with thiols can be inhibited. Examples of depressant action are presented. The relevance of electrochemical investi- gations to practical flotation is Discussed.

Jan 1, 1984

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

The nickel refinery at Yabulu consumes an average of 118,000 kg/h of low pressure steam in stripping operations to-recover ammonia and carbon dioxide from product liquor and ore tailings streams. The steam used in the stripping operations is produced from the 25 MW power generation plant at the refinery. The back pressure on the non condensing steam turbines is maintained at 60 kPa.Studies have been carried out to determine the optimum amount of steam required to be generated for stripping operations. When steam production is increased, the product liquor flow from thewashing thickeners can be increased. This results in improved washing efficiency of the thickeners and therefore improves the plant nickel recovery. A computer thickener wash model was used to predict nickel recoveries at varying steam consumption rates.The studies have shown that in most plant situations, it is not economical to-generate more steam than that already available from existing power production.The studies also highlighted the necessity to use all steam generated from power production at all times to maintain maximum nickel recovery.

Jan 1, 1985

By M J. Ireland, D P. Horne, S J. Simpson

The Sinclair Nickel Project, wholly owned by Xstrata Nickel Australasia (XNA), includes an underground mine, a concentrator, a village, an all-weather airstrip and associated mine infrastructure. The operation is located 70 km north of Leonora in the prospective and historically productive eastern Goldfields region of Western Australia. Xstrata Nickel has successfully developed the Sinclair deposit into a 350 kt/a operation since its discovery in November 2005, with contained nickel metal production to date in excess of 10 600 t, of which 5500 t is from the underground operation.The narrow, continuous, medium-grade Sinclair nickel sulfide deposit accessed by the Phoenix Decline has a shallow 15¦ - 20¦ plunge that is approximately 1000 m long down dip and open at depth to the north. The flat plunge and low-grade nature of the orebody presents challenges regarding the amount of horizontal waste development that can be economically excavated, which in turn affects ventilation, egress, mine services and diamond drilling.The mineralisation is hosted between an ultra mafic hanging wall and a basalt footwall and is being mined using a bottom up, sublevel open stoping method. The stopes are retreated to a central access, filling voids in the process with waste mullock where possible and using cemented mullock fill where end exposure is required. Tight filling the flat dipping hanging wall has proved to be challenging given the angle of repose for the waste mullock fill is steeper than the angle of the hanging wall.Reconciliations of mine performance against the original feasibility study show positive changes and operational optimisations enabling Sinclair to achieve its mining targets in a safe, sustainable and economic manner. This paper discusses the mining operations associated with the first two years of the Sinclair Underground Nickel Project, providing an overview of the various issues encountered and the lessons learnt in the process.CITATION:Ireland, M J, Horne, D P and Simpson, S J, 2012. Overcoming mine design and production challenges at the Sinclair underground nickel project, in Proceedings Narrow Vein Mining 2012 , pp 37-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

Many of the discrepancies that appear when comparing the results of reducing machinery are due to the nature of the materials reduced and the conditions under which they have been treated. It is therefore necessary that manufacturers should employ standard materials in their tests that sufficiently approximate the substances to be ultimately treated if the information is to be of any value to the purchaser. Another advantage to be gained by employing universal standard materials is that by their means one is enabled to compare the relative values of different types of machines. At present much of the data meted out to the public is insufficient to enable them to judge fairly. Of course the best test would be to send some of the stone tor which the machine is required, to be treated by the various crushers in the market that are likely to be suitable for the purpose, but this is not always possible. It would not take long to become accustomed to judge of the value of a machine for a specific purpose if it was guaranteed to work a certain quantity of some standard rock, even if that standard were not identical with the material to be treated.There are many points to be considered before selecting a machine, such as the size of the rough stone it will take, the size to which it will reduce it the proportions of various grades made when crushing to pass through a given mesh the form of the delivered particles the time taken to treat a+ certain quantity the horse-power required to drive the machine, both when loaded and unloaded whether constructed to crush wet or dry the wear and tear of the machine its total weight and weight of the heaviest part the cost of machine what attention it required whether the wearing parts are readily replaced, and several other points common to all machinery. 'When considering these varying quantities, we can tell at a glance certain machines that are suitable for a particular sort of work, and can then compare those belonging to the same class, thus avoiding errors made purposely or through ignotance by persons interested in different machines, who frequently compare machines originally constructed for.

By W van der Westhuizen

Mining professionals recognise the need and application for reconciliation and value tracking. It is necessary however to examine our current reality, and evaluate the following. Do our reconciliations really balance correctly, and are we able to track value effectively throughout processes? If we are honest, in most operations the answer is a resounding no. This means that we are surrounded by fluctuation and deviations that we do not account for and do not understand. This is astounding, because given our level of scientific knowledge and the technological tools at our disposal we should have a good understanding of our environments and be able to manage them effectively. How do we manage effectively if we are surrounded by so much uncertainty? The purpose of this paper is to describe, at high level, the principles of reconciliation and value tracking, to highlight some areas where deviations are introduced into the mining process, and to propose a different approach to the apparent reconciliation and value tracking conundrum. The paper also poses several questions that need to be critically addressed at most operations. Instead of making the same mistakes each month in reconciliations, mining professionals need to acknowledge two facts. Firstly there will be uncertainty that we need to accept, since all our estimates are based on sampling, an orebody is not homogeneous and peopleÆs behaviour will influence the process, etc. Variability will always exist and lead to uncertainty. What is the current approach in the reconciliation process when a deviation occurs and how do we use reconciliation and value tracking to manage and improve our business? The second fact is that we need to stop using reconciliation and value tracking to only measure and report. We need to adopt a new approach to manage mining throughput, where reconciliation and value tracking are enablers to the success of the business. In most mining operations, significant effort goes into planning and measurement for the purposes of reconciliation and value tracking. The importance of accurate and effective reconciliation and value tracking should be to ensure the maximum utilisation of the resource, maximising throughput and enabling the business to deliver a product to its client, of the correct quality and in a timely manner.

Jan 1, 2002

There is considerable variability in the level of detail incorporated in prefeasibility studies relating to mining developments. Hence, when undertaking a review or audit, it is critical to attempt to ascertain at an early juncture precisely who has compiled the various facets of the study, for what purpose it was intended and the terms of reference given to the authors. Likewise, when commissioned to undertake an audit it is preferable to have proper terms of reference and to be aware of the purpose to which the audit will be put.These factors will influence the degree of detail an auditor would expect to find in the study and consequently, the degree of effort/time required for the audit process. In most instances audits do not imply recalculation of the entire study or modifying it in anyway, but involve an overall assessment of the methodology used, combined with spot checking of detail. One of the most difficult aspects is to determine a realistic order of accuracy for the overall study when the accuracy of the individual components may differ markedly.

Jan 1, 1990

By Mernagh T, Large R. R, Ryan C. G, Huston D. L

The Tennant Creek goldfield is one of the largest gold producing districts in Australia, and major deposits, including Gecko, Juno, Orlando, Peko, Warrego, Nobles Nob, Golden Forty, Argo, TC 8 and White Devil have produced more than four million ounces of gold over the past two decades. Gold-copper-bismuth mineralisation at Tennant Creek occurs in lenticular, ellipsoidal or pipe-like bodies of magnetite-hematite ironstones which are hosted in turbiditic sedimentary rocks of Proterozoic age (Large, 1975; Wedekind, Large and Williams, 1989; Le Messurier, Williams and Blake, 1990; Morrison, Donnellan and Hussey, 1992).

Jan 1, 1994

This is the seventh major symposium organised by Illawarra Branch over the past five years and the fifth dealing with various aspects of coal. It is clear that all of you here need no convincing that black is beautiful! This symposium is on a broader canvas, covering the overall field of occurrence, preparation and utilization of black coal throughout Australia. It is thus the most comprehensive treatment of the subject by the Institute since the symposium organized in 1950 by the Sydney Branch with the co-operation of the then newly formed branches in Newcastle, Illawarra, Central Western N.S.W. and Southern Queensland, all of which shared coal as a major interest. The 1950 symposium was adopted as a volume in the series of seven published by the Fifth Empire Mining and Metallurgical Congress in 1953. This historical reminiscence brings to our minds the circumstances in which these new Institute branches were formed. This happened in the year of the presidency of the late Frank Hockey, and at the time the Australian black coal industry was in many ways at a very low ebb. It was the time of extreme shortage of coal following World War II, and the industry was beset by industrial unrest on such a scale that daily bulletins were posted listing the number of idle pits, of idle miners and of tons of lost production. There could not, of course, be any thought of export marketing. Some of the more picturesque bulletins recorded the number of pits at which the ceremonial emptying of billies took place, and the number of pits at which the aroma of the horses' breath was insupportable. At an Institute conference at the time it is on record that the late lamented Austin Edwards, that tireless mineral researcher, author and editor, in his gentle way chided the personnel of the industry and the members of the Institute for having allowed a situation to develop in which a whole generation of Australian children could grow up without ever having seen coal or knowing what it was. It is sad that most children and most Australians have still never seen coal, and think of it as something dirty and uninteresting. The desperate situation of the black coal industry inspired moves by people in industry and in governments, whose plans and efforts have been recorded elsewhere, to modernize coal mining methods, to introduce coal preparation, and generally to restore the mines and the mining communities and to re-cast the steel industry and electricity generation. Amelioration of the traditionally troubled industrial relations was an integral part of this overall programme, and whilst one would wish this aspect had progressed further the situation has, in fact, improved immensely. New investment in exploration, mining, preparation, transport and utilization both by the existing coal mining groups and by new entrants, Australian and overseas, have played a large part in bringing about the transformation of the industry to such a point that Australian needs are being fully met and a large export market is being supplied - a situation that few would have dared to hope for in those dark post-war days. Forecasts of exports from New South Wales and Queensland show coal becoming a dominant foreign exchange earner for an indefinite term. Old King Cole may have vanished from our children's nursery rhymes but King Coal is here to stay, providingthat costs in the industry can be kept within competitive limits. It is all too easy for an industry to price itself out of the export market by inflation, by increased costs for a variety of reasons, and through currency readjustments. A second proviso is that we must continue to encourage a balanced attitude to environmental matters.

Jan 1, 1975

The history of the physical chemistry of steelmaking is reviewed through international conferences, and compared with the Japanese contribution. Subjects remaining to be solved are discussed. Several steelmaking technologies developed recently in Japan are surveyed.

Jan 1, 1980

The original design of the Bougainville Copper Limited (BCL) concentrator took cognisance of the constraints imposed by the topography, the need to minimise capital cost, and the need to allow for plant expansion which, it was known, would be necessary to maintain copper and gold production as head grades declined.At the same time as spare slots have been taken up with additional equipment, technological innovations have been embraced whenever there appeared to be a chance of improving the productivity ofexisting equipment, or replacing it with a more efficient alternative.There are many examples of this in the BCL concentrator in the areas of process control, process design, instrumentation, materials handling, equipment design and wear part technology.Current process developments also pursue the latest technology. The development of the Omnicone crusher, flotation control, tailings water reclamation, and the variable speed gearless drive on the No. 13 mill are prime examples.

Jan 1, 1986

By Whiten W. J

The control of mineral processing plants incorporates a number of off-line and on-line actions by plant personnel to obtain satisfactory plant performance. In general, off-line actions centre around intensive data analysis, while on-line activities are either automated control actions or prompted by qualitative interpretations of quantitative and qualitative information. Data sets obtained by various data logging devices and laboratory analysis of samples in many modem plants may be very large and are often unmanageable. This paper presents a method of analysing the data sets typically found in mineral processing, based on cluster analysis. The results of this analysis leads to a more complete understanding of operations in comparison with existing analysis tools used in mineral processing.Improved process configuration, optimised control strategies and in some cases, direct use of the results in monitoring process unit operations may be achieved.

Jan 1, 1992

The ER&S Company operates a copper sinter plant, blast furnace and converter smelting complex at Port Kembla. Eighty percent of the smelter feed is dirty copper concentrates that contain some lead and zinc. The remaining twenty percent of the smelter feed is copper bearing secondary materials, some of which contain lead, zinc and tin. A predominately lead/zinc fume is produced during the smelting and converting of this feed mix. The composition and tonnage of fume produced at Port Kembla has varied over the years as the smelter feed sources have changed. The economic processing of the fume has always been dependent on the value of the metals contained in the fume and on the fume composition. Both pyrometallurgical and hydrometallurgical methods have been used to treat the fume for the recovery of some or all of the following metals - lead, zinc, tin, copper, cadmium, silver and bismuth. A detailed description of the treatment methods that have been investigated and used to process ER&S fume is given.

Jan 1, 1984

A good blending system is one that ensures that a plant can cope with the amount of grade variation that it will encounter. Prediction of amounts of variation that will be encountered on time or tonnage scales that are important should be regarded as an essential part of the planning of mines and plants. In some cases, the natural amount of grade variation when ore is mined and handled in the cheapest way will be acceptable. In other cases, it is necessary to understand the effects that various ore-handling processes have on amounts of grade variation at various scales and to design a blending system with considerable care. Blending tends to matter more when plants are sensitive to many aspects of grade. It can be very difficult to find the best compromise between capital cost and the amount of grade variation. In these cases it is important that ore blending options be considered carefully as part of the planning of mines and plants. Failure to make plans that consider likely amounts of variation can be very expensive.

Mar 1, 2010

Cyanide is a significant contributor to the cost of producing gold. Any reduction in cyanide consumption that is achieved through more reliable measurement, and/or more efficient management of cyanide dosing rates, can produce a significant financial saving to the mine operation.

Jan 1, 1997

By Emerson D. W

The search for economic mineral deposits is becoming more difficult as exploration goes deeper in the established mining camps and spread out to the surrounding covered areas, which may have an `overburden' some hundreds of metres thick. Geophysics is finding an ever increasing role in such exploration. When the target is zinc, the task often becomes even more difficult since sphalerite, the most commonly mined mineral, is non-magnetic, resistive, and relatively light compared to other sulphides. Fortunately, sphalerite commonly occurs in association with other sulphides, which are magnetic and/or conductive and/or heavy, thus most zinc-rich orebodies have at least one contrasting physical property to aid exploration. This paper presents the physical properties of sphalerite and other potentially important zinc minerals. Results of petrophysical measurements of samples from various zinc-rich ores are presented together with examples of geophysical surveys over a number of zinc deposits. The results show that the physical properties are not merely dependent upon the properties of the orebodies' constituent minerals. For example, the small (0.4 Mt) and low-grade (five per cent Zn + three per cent Pb + two per cent other sulphides) Flying Doctor deposit at Broken Hill, New South Wales (NSW) is much more conductive than the large (3+ Mt) and high grade (14 per cent Zn + five per cent Pb) Cadjebut deposit in Western Australia (WA). In the former case, tectonic stresses have

Jan 1, 1993

Australia's gold mining industry has seen a resurgence in the past seven years - a resurgence the likes of which has been seen in very few, if any of this nation's other mineral industries. Industry experts are predicting that Australia could become one of the world's largest gold producers as the future of the South African gold industry looks increasingly tenuous under the present political crisis in that country. Therefore, it is utterly ludicrous for the Federal Government to introduce a tax which will see the Australian gold industry "wither on the vine."The Queensland State Government is utterly opposed to a tax on gold. Anyone in their right mind, who has seen the statistics could only agree with our stance. In 1984/85, activity in the gold mining industry is estimated to have accounted for over $750 million in national income, over$1,200 million in national output, and tax revenue of at least $115 million as well as providing more than 16,000 jobs. Chartered accountants Coopers and Lybrand's survey on the gold industry last year showed an increase in exploration expenditure by gold producers and explorers by up to 36% in 1986 from 1985 levels. That level is expected to be maintained in real terms for most of the remainder of the decade under the present tax arrangements. This is in contrast with the mining sector as a whole, where a recent Australian Mining Industry Council survey forecasted a 14% FALL in production.

Jan 1, 1986

Modern, high-output, continuous process plant requires heavy capital expenditure and is exroected to achieve a high rate of return upon the investment made, thus its high utilisation is an economic necessity. Downtime is extremely expensive not only in terms of idle capital but also in terms of lost production and revenue. A sound maintenance management system can alleviate the problem of unscheduled stoppages and a key document in the maintenance system is the Work Order because it both initiates work and conveys maintenance control information back to the administrator. This key document must be supported by an information base that provides technical data, job procedures, spare parts, history and costing. To be effective this information must be easily and immediately available to all concerned. Computer technology has developed extremely rapidly over the last ten years and with it a wide variety of on-line computerised maintenance systems. Selection of the most appropriate system for a given industrial plant is not a straight-forward process. Computer requirements for hardware and software must be matched to the requirements of the maintenance system and such matching must be carried out in an ordered and rational way. At Kalgoorlie Nickel Smelter, time was taken to review the existing maintenance system, select, study and test the new computerised maintenance management package and plan its implementation. As a result, the initial target of equipment recognition has been achieved on schedule and within budget.

Jan 1, 1987