Search Documents

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

The specification for tender nominated the requirements for ore hoisting and servicing; this showed that one common duty winder could be selected. Foliowing the design of the shaft layout, the merits of fixed or rope guides were compared and the latter selected.The specification called for the supply and installation of the complete hoisting system. Construction of the winder tower and shaft bottom steel work had to proceed while mine development was in progress using the sinking winder and headframe. Guide ropes, winder ropes, and the sky shaft were installed in the shortest possible time, and as the shaft was not equipped with ladder-ways, a second means of access had to be provided.Very few problems were encountered witll the commissioning of the winder, and in the first 2 years of operation the only significant modification was to the circuitry associated witll the moving access platforms.Hoist rope tension checking and adjustment are simple, and non-destructive testing has shown no deterioration of these ropes. The operation of the balance ropes has been very satisfactory but cleaning presented problems in the early stages. Guide ropes have been trouble free and require minimum attention.Normal wear on the PVC rope groove inserts on the winder drum has been negligible.Since the commissioning on fully automatic ·control, the winder has operated with very few, minor delays.

Jan 1, 1969

By Gallet M, Watsford R. M S

The 1989 feasibility study of the chessy, france, copper, zinc, pyrite and barite orebody was based upon a classical flowsheet. The flowsheet included, three stages of crushing, conventional rod and ball mill grinding in series, and sequential flotation of four products utilising conventional mechanical flotation cells. To improve the profitability of the project the partners commenced a search for ways to reduce the projected capital and operating costs of the proposed development. This paper presents the improvements in the projected capital and operating costs as a result of design and concept changes. The major changes included: ò the simplification of the crushing section with the adoption of semi autogenous grinding (SAG) milling of primary crushed ore. ò the deferral of pyrite and barite flotation circuits until market conditions were positive. ò the simplification of the flotation circuit by the use of column flotation cells for combined rougher/cleaner duty. ò the purchase of second hand equipment. The result of these changes was to reduce the capital cost estimate of the plant from US$ 21 million to US$ 11 million and operating cost estimates from US$ 18.90 to US$ 13.60 per tonne of ore for a decrease of approximately ten per cent in potential revenues.

Jan 1, 1991

By H Zahiri

Utilisation of the InSAR technique for monitoring of subsidence in mining areas, employing open pit and underground mining methods, has large potential due to sensitivity and safety issues associated with usage of the classical surveying techniques. InSAR can also be very competitive concerning the cost of provided results. However, there are a few issues that may significantly limit InSAR applicability for subsidence monitoring in mining areas. The altered terrain topography, involving steep slopes and deep pits, may lead to the layover of radar signal for specific satellite and pit geometry. Also, the highly dynamic character of subsidence induced by mining, especially using mass mining methods, may lead to issues such as apparent heave and ambiguous results. In this paper the authors analyse the above-mentioned issues and demonstrate how InSAR technology was applied, as a supporting system, to monitor large scale and highly dynamic subsidence for a real case study in Western Australia.

Jan 1, 2008

By Mitchell D. S

BackgroundIn March 1990 Pasminco resolved to replace and increase the capacity of the underground pumping system at the Southern Operations, Broken Hill. The existing pump station was built 23 years ago while the rising main had been in service for 38 years and was subject to frequent failure.The old system was a conventional slurry/clear water separation and multi-stage pumping system. It was inadequate in the following areas:ò insufficient capacity to handle current and expected future flows;ò unable to consistently dewater lower production areas; ò pumping capacity restricted sandfilling rates;ò dirty water dams had insufficient settling capacity and were difficult to de-sludge;ò the operating costs of dewatering were high; ò it was labour intensive; andò it did not offer enough protection to the 25 level loading station.

Jan 1, 1993

In Australia, current production of rare earth element (REE) minerals, monazite and xenotime, occurs as by-product from titanium-enriched placers and beach sands. Undeveloped REE resources are associated with carbonatites, alkaline igneous rocks, pegmatites, phosphorites, cemented fluvial sandstones, and uranium mineralisations. The REE are held within a range of minerals including silicates, phosphates, a1uminophosphates, carbonates, and oxides. The development of these REE resources may require new processing and extraction methods. The distribution of REE in the currently mined ore minerals, monazite and bastnaesite, does not match that requested by the market. Exploration for new REE resources should be focused on ores with more marketable REE distributions, particularly with heavy REE, neodymium, samarium, europium and yttrium enrichments. Such ores occur within alkaline igneous rocks, in laterites overlying carbonatites and alkaline igneous rocks, and in placers derived from low-grade regional and contact metamorphic sediments. Lateritic REE deposits may be easily and economically mined by shovel in open pits and are unlikely to require extensive crushing and milling. In addition, lateritic REE clay deposits may be processed by simple hydrometallurgicaltreatment mehtods.

Jan 1, 1991

By Bicer N

Current problems in predicting sub-surface strata movement and fracture development due to longwall mining have highlighted the need for more accurate, dependable methods of physical modelling of rock mechanics problems which are beyond the capabilities of current mathematical techniques. Physical model studies of the caved zone above the working faces up to the base of a water source are of importance in attempting to understand changes in mass permeability due to induced fracture zones and the resulting ground water conditions. Turkey's most important supplies of coking coals are to be found within the hard coal resources of the Black Sea coast. Coal seams up to 9 metres thick, dipping at angles as steep as 90 degrees are being successfully mined at the Kozlu Mine. Since 1956, mining operations have been carried out under the sea in dry conditions. The undersea mining conditions of the Kozlu Mine have been investigated using scaled physical models constructed from artificial materials which satisfied necessary scaling requirements. Models representing the in-situ conditions were tested and the following extraction sequence was employed: 1. The Sulu Seam extraction 2. The Acilik Seam extraction (as two slices) 3. The Piric Seam extraction. The displacement of the fixed reference points were subsequently measured using a high precision photogrammetric technique and induced horizontal and vertical strains were calculated.

Jan 1, 1988

Reverse circulation (R.C.) drilling or the dual tube method as it is quite commonly known, has a unique place in conventional mineral drilling. It can be classified half-way between open hole drilling at the lower end of the scale and diamond drilling at the upper end. The system basically consists of two tubes, one inside the other, with compressed air flowing between the inner and outer tubes. Sample cuttings return up the inner tube through the head of the rig and via a hose to a cyclone where the sample is collected. This system means that the cuttings are free of contamination as they are at no time in contact with the outside formation of the hole.Reverse circulation drilling is divided into two areas: R.C. Roller and Blade for softer formations; and R.C. Percussion for harder formations.

Jan 1, 1986

By W A. Tchernykh, R P. Strelnikova

In connection with the fact that technology of ore mining by caving system is often used when mining of deposits, characterising by low stability of surrounding rock mass, the main problem for such ore mines is ensuring stability of mine workings, placing in a zone of influence of winning operations. Besides natural disturbance of ore mass, stability of workings depends on the dynamic effect of blasting operations and also on the dynamic effect of structural blocks detaching from the ore mass and colliding with crests of ore pillars in the bottom of a chamber. Decreasing of dynamic stresses may be achieved by way of creation of a compliant porous screen or an ore cushion in the chamber bottom. It is established that maximum levels of compression take place when the first impact impulse occurs, and after that increase of compression of protective slice decreases. Necessary thickness of screen slice was substantiated theoretically with due account of height of structural blocksÆ fall, their mass, deformation modulus of ore mass and ore cushion.

Jan 1, 2003

The large, high grade 3000 and 3500 copper orebodies at Mount Isa lie greater than 1200 m below the surface, and partly beneath the silver-lead-zinc mining operations at the Isa Mine.Since discovery over 30 years ago, the primary data acquisition programs have been integrated with long-term copper production strategies. These potentially sizeable and distinctly separate accumulations of copper mineralisation are the only sources capable of supplementing a decline in output from the 1100 orebody in the 1990s. Within a decade these deeper copper orebodies will become the major source of copper ore.

Jan 1, 1993

By Phillips D. N, Herbert H. K, Fletcher A. C, Lewis R. K

Quartzite is a common feedstock used for the production of silicon by reduction at high temperatures in a submerged electric arc furnace. Silica fume, formed as a by-product in this process, contains crystalline silica in the respirable fraction. The crystalline silica in the fume represents entrained quartz derived from unreacted quartzite raw material within the furnace. A knowledge of the fragmentation of quartzite feedstock, in response to thermal disaggregation in the furnace, is important in feedstock selection to help minimise (a) the amount of crystalline silica in fume, critical from an occupational health and safety perspective, and (b) impurity levels necessary to achieve the highest possible purity of product silicon. In this study, a series of quartzites has been assessed in terms of the above requirements and correlations drawn between mineralogical and chemical characteristics. Alkaline solubility correlates with grain-size and level of stored strain in the quartz matrix. Grain-size affects the surface area available for attack while stored strain enhances the chemical reactivity of the strained matrix as well as profoundly influencing the disaggregation and microfracturing characteristics of strained grains and, hence, available surface area for chemical reaction.

Jan 1, 1995

By Brenchley R

Partitioning behaviour studies for -particles in the 250 to 1,000 micron size range at. the Curragh coal preparation plant are presented. Plant surveys were conducted to compare the partitioning efficiencies of dense medium cyclones and froth flotation. The aim was to assess the potential for improving yield of coal by directing more of the top size of flotation feed material to dense medium cyclones. ovel mass balancing and model fitting NI procedures were used. While flotation offers high yield of low ash particles smaller than 500 microns, dense medium cyclone rejection .of high ash particles larger than 250 microns is superior. These strengths of the two processes are turned to good advantage by the use or desliming sieve bends which tend to perform some density separation on the'size fractions of interest, directing lower ash material to froth flotation than to the dense medium cyclones.

Jan 1, 1987

By W A. van der Westhuizen, Beukes G. J, Vermaak J. J

Large parts of the arid northern Cape Province South Africa are blanketed by Quaternary cal- crete under which potential base-metal ore- deposits may occur. In an attempt to examine the nature of the distribution of such ore-re- lated elements in a calcrete environment, calcrete and soil samples from the copper-nic- kel prospect at Jacomynspan and the copper- zinc deposit at Copperton were examined. Both deposits form part of the Namaqua mobile belt. CALCRETE GENESIS In Southern Africa calcrete is restricted mainly to the western two-thirds of the sub-continent, south of the latitude 17¦ S. Various models have been put forward to explain calcrete genesis and Goudie (1973) and Netterberg (1969a) give detailed discussions on this topic. The most popular model for calcrete genesis is one of pedogenic origin. McPherson (1979), Watts (1980), Wright (1982), Arakel (1982), Netterberg (1969a), Goudie (1973) and Multer and Hoffmeister (1968), amongst others, support the hypothesis of calcrete formation by carbonate precipitation from downward percolating calcium carbonate rich soil waters. Calcium carbonate is usually initially precipitated as nodules or grains which can develop to form more compact layers.

Jan 1, 1988

A proved routine mapping practice is described involving detailed observations on grade and structure. The equipment and methods employed are giving good service under the conditions encountered. Stopes are mapped on every floor whether timbered or open, "Kodatrace" workplans and sections being used, and in addition all development whether in country or lode is mapped.INTRODUCTIONThe accumulation of geological data for application to current mining problems and to the search for new ore involves the necessity for close mapping of all available underground faces and backs. The technique which has been developed to suit conditions at the North and British mines of North Broken Hill Limited forms the subject of...

Jan 1, 1940

Current mine ventilation systems have evolved from simple, limited energy, series or multi split layouts motivated by low suction, slow running, surface fans. Concentration of coal production from fewer working places and ventilation splits, and varying needs, hazards and challenges, however, have led to substan- tial changes. Modern ventilation systems, therefore, are more complex, sometimes more interdependent on others, more energy intensive, and are founded on the use of multiple airways and greater suction, higher speed surface ventilators and often booster fans. Intensi- fication of output has resulted also in higher gas emission rates, the wide adoption of fire- damp drainage, and sometimes in particular problems such as spontaneous firedamp emissions. Some coal mines are subject to spontaneous outbursts of coal and firedamp. These and related matters and current practices and developments are leading to discernible trends, potential advances, and further changes in Practice.

Jan 1, 1983

The Mesozoic intrusive rocks in southeastern coastal China can be divided into three intrusive suites, and they can be brought into corresponding with four cycles of volcanic activity. This paper describes their time-space relation with volcanic rocks, and their geochemical characteristics. Data from the Mesozoic volcanic-intrusive. complex rocks in Eastern Zheijiang, Eastern Fujiang and Eastern Guangdong show distinct regional differences, both within and tectonomagmatic activity regions. The southeastern coast of China involves four tectonomagmatic activity regions. They have many differences on the nature of magma source regions, activity patterns of magma, time-space distribution, petrography and petrographic facies association of volcanic and intrusive rock and mineralization.

Jan 1, 1990

By Svenson D

Most exploratory drilling in the N.S.W. coal fields has been conducted using convent- ional diamond drill rigs of modern design, us- ually truck or trailer mounted. Conventional diamond drill rigs have also been used exten- sively by the Queensland Department of Mines for coal exploration. However almost all of the exploratory drilling of surface mine coal prospects throughout Queensland has been conducted using rotary rigs typified by the Mayhew 1000 truck mounted unit. The rotary rig has proved capable of both rapid non-core drilling and core drilling with high core recoveries when modern core barrels have been used by experienced drillers. For deep or continuous core drilling, wire-line equipment is now in general use. Both wire-line and conventional coring is effected using stationary split inner tube barrels, for minimum core disturbance, maximum core recovery, ease and accuracy of logging and sub-sectional sampling. Diamond core bits are generally required in N.S.W., with water circu- lation. In Queensland, the generally softer coal measures strata can be successfully cored using tungsten carbide bits and air circulation is the preferred method where possible.

Jan 1, 1977

By E Topal

Risk and uncertainty are attached to mining projects, and making decisions, hedging, future investment and evaluation of mining projects depend on forecasting the future price. The future technologic developments in mining will be primarily influenced by the future commodity prices. A few approaches, with different confidences are proposed to predict price movement in the future. This research introduces a new comprehensive version of the mean reverting jump diffusion model for natural-resource commodity prices. The novel model proposes that the historical data of mineral commodities have three terms to demonstrate fluctuation of prices: mean reversion component, diffusion component and jump component. The model calculates each term individually to compute the future prices of mineral commodities. Subsequently, in the second section of the paper, the model is implemented for monthly historical data of gold price from January 1968 to May 2008. This research is investigating the relationship between the historical oil price and inflation with the gold price. This is followed by a future estimation of gold price fluctuations up to 2018. The results from the application of this new method are discussed in the context of how they accurately replicate the historical gold price and how they can predict the future gold price.

Jan 1, 2008

By Segnit R. E

Two suites of dusts (waste-heat boiler and electrostatic precipitator) collected in 1976 and 1980 from the Kalgoorlie nickel smelter were subjected to chemical and XRD analysis and were examined by SEM and optical microscopy. The spherical to sub-spherical particles contained oxide and glassy phases with small amounts of sulfide. XRD showed that the major phase was a mixed Ni-Fe oxide spinel with some hematite. These phases compared well with those predicted by thermodynamics. The particle size distributions showed that in the 1976 and 1980 suites 20 per cent by weight was respectively coarser than 60 and 115/lm (boiler dusts) and 40 and 30/lm (precipitator dusts). Maximum particle sizes estimated from sedimentation chamber theory were found to be in reasonable agreement with the maximum sizes found in the dusts.

Jan 1, 1984

By J E. Everett

Ore selection is generally a highly subjective task, with emphasis on producing product with a consistent target grade matching a perceived market requirement. A composite selection criterion ‘Comp’ (a linear function of the grade vector) can be used to maximise ore tonnage at a specified target grade (in Fe and contaminants) extractable from a block model. The blocks correspond to the selective mining units, with grades interpolated from diamond drill hole data. An iterative procedure has been developed to identify the coefficients and cut-off value for the composite function ‘Comp’, maximising potential ore tonnage at target grade.Commonly, target grade is predetermined by marketing; however, there is no guarantee that maximising ore tonnage at a specified target grade maximises the potential value of the mine. If the value of ore could be expressed as a linear function of the grade components, then these coefficients would be appropriate for the selection criterion ‘Comp’. The cut-off value for ‘Comp’ would correspond to the marginal cost of production; all blocks with a ‘Comp’ score above the cut-off would be classified as ore; and the cumulative grade of these ore blocks would be the average product grade over the life of the mine.Unfortunately, no such value function for iron ore is generally available. Methods for estimating the value function are discussed, using the spot price and sensitivities based either upon operational tolerances for Fe and the contaminants or upon published price differentials. This approach has been applied to an anonymous Pilbara deposit with about one million blocks averaging 1.1 kt. It is shown how the optimal target grade, cut-off grade and maximum tonnage can all be explored as a function of marginal cost and iron ore price. Alternatively, given marginal cost and an iron ore price, the effects of changing the tolerances (and therefore the relative costs of the contaminants) can also be explored.It is suggested this procedure can enable informed decision-making for an iron ore mine. Rather than setting final policy for the entire life-of-mine, the method enables target grades and tonnage estimates to be revised by re-computation as the mine life proceeds to recognise changes in market conditions and knowledge about the resource.It should be emphasised that this paper is concerned with ore selection rather than ore sequencing. Appropriate ore selection is a necessary but not sufficient condition for maximising value. Having identified the set of blocks that potentially maximise value, the sequence in which they are mined will present a trade-off between producing at constant grade and extracting high value ore early. The sequencing issue is not considered here. It is shown that optimum ore selection for an open pit mine is independent of any consideration of discount rates, although ore sequencing will depend upon the time value of money if the product grade is to vary across time.CITATION:Everett, J E, 2015. Ore selection to maximise value, in Proceedings Iron Ore 2015, pp 443–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015