Search Documents

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

In 1939 at the annual meeting of the Australasian Association for the Advancement of Science, held at Canberra, a paper was contributed by E. de C: Clarke and H. A. Ellist in which a plea was made for more "facts" concerning metasomatism near ore-bodies in Western Australia. From time to time writers here, and in other parts of the world, have discussed the alterations in wall rocks of various reefs and lodes, but little has yet been attempted in the matter of accumulation of quantitative data, both chemical and mineralogical, and in the correlation and comparative study of this data. Such a detailed comparative study is needed to determine the economic value of a practical application of our accumulated knowledge of the phenomena of metasomatism.When in 1939 the opportunity offered for an examination of the core from 4 bores recently put down by the Big Bell Mines Ltd., to explore the ore-body of the Corinthian G.M. 10 miles N.W. of Southern Cross, Western Australia it was hoped that some small beginnings might be made of an accumulation of comparative and quantitative data regarding the metasomatism of the wall rock immediately adjacent to this ore-body.By the courtesy of the Big Bell Mines Ltd., the core from the 4 bores was delivered to Survey Headquarters, Perth;in the middle of June, 1939 and copies of assay plans of part of the underground workings at Corinthian, and of the results of assays of the bore cores, were also supplied by the management of the above company.It was not, however, until March, 1940, that it was 'found possible to investigate the core. At that time the writer's colleague, Mr. R. S. Matheson, conducted a: megascopic examination of all the bores and selected material from two of these for possible future chemical analyses. Late in 1940 the writer commenced a microscopic petrological examination of this material.AIM OF THE INVESTIGATIONThe object of the petrological part of this investigation was to determine whether from a megascopic and microscopic examination of the core, any evidence could be obtained indicating changes, in mineralogical composition...

Jan 1, 1942

Wrenching between basement blocks is considered to be the mechanism whereby a well developed set of en echelon folds and an associated fracture system are developed in the Fitzroy Depression, Western Australia. The regular geometry of these structures accords with a right lateral regional coupling between high-standing, basement blocks bounding a trough filled with a thick pile of stratified Phanerozoic sediments. The structures developed during or after the Mesozoic Era, but the couple is inferred to have been applied to blocks outlined by old lineaments, which may reflect strains or ruptures in basement that developed during the Precambrian, and which were regenerated during Palaeozoic and Mesozoic time.

Jan 1, 1967

By Riley TW

This paper describes a Process Simulation Package for modelling the steady-state operation of a mineral processing plant. There are two levels of input allowed into the package. The first allows simple manipulation of the process models within a defined modular format which enables a wide range of process systems to be simulated. "The second level of input is via a Command file which allows plant models to be defined and changed without reference to the code or the requirement of any recompiling of the programme sources. The Command file interface was designed for use by metallurgists and assumes a sound knowledge of the system being modelled. As such it is an effective tool for metallurgists rather than a user friendly generalised package for the layman.

Jan 1, 1985

By Thorburn D

This paper reviews the history of environmental assessment in New Zealand with reference to mineral developments. Emphasis is given to larger more controversial projects particularly metal mines. The changing role and application of the Environmental Protection and Enhancement Procedures is examined in the context of changes in the government's environmental administration and the response of the Ministry of Energy's resource allocation group. Conclusions are drawn on the effectiveness of the present environmental assessment activities and on the allocation of administration of priorities in the Ministry. The Ministry of Energy has effectively ceased to exist.

Jan 1, 1990

The difficulty of successfully imple menting a landscape policy is almost incom- prehensible. Landscape design is recognised as an essential component in the integration of engineering and architectural projects into the landscape, but the factors which prevent the achievement of a successful result are rarely recognised or assessed. In many cases these prohibiting factors are due to a lack of understanding of the effect of major planning decisions on the existing landscape, the importance of the landscape plan and the significance of appro- priate specified techniques to prevent un- necessary damage and to ensure retention of existing vegetation in a healthy condition. The role of the landscape architect in incorporating new land uses into the landscape provides the background against which factors which inhibit policy achievement can be con- sidered.

Jan 1, 1976

The various functions of public relations are playing an increasingly important part in the activities of the many companies now engaged in oil exploration in Australia.Several of the larger exploration companies, notably West Australian Petroleum Pty.Limited, Ampol Exploration Limited, Caltex Oil (Australia) PtSr: Limited and Australian Oil and Gas Ltd. (and its American Associate Union-Kern), employ staff or consultant public relations specialists. In, most of the other companies now exploring in Australia, public relations are handled within the company, directed from the highest executive level.The object of public relations in.the oil industry is. to create in the public mind an impression favourable to the industry as a whole and'the company -or group of companies with which the public relations officer is associated.

Jan 1, 1962

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops.

Jan 1, 1992

Process control computers are finding ever increasing applications within the chemi-cal and mineral processing industries.To purchase a system which fulfils both the immediate and future needs of operating, technical and management groups, requires an appreciation of the capabilities of the system software and the constraints which apply to user development of application software. Early decisions are then required as to who will develop and maintain the software. Rules and conventions must be determined and adhered to if the end result is to be an orderly, well structured and properly documented system. Software development and maintenance represents a substantial, and often hidden, cost. Getting it right the first time will avoid either a major re-work, or having to live with a system which is extremely diffi-cult (at the worst, impossible) to trouble-shoot or modify.

Jan 1, 1985

Mineral exploration management has undergone major changes particularly in the last decade. Parallel to these changes in management, and partially responsible for them, have been the changes in governmental laws and regulations at both National and State levels reinforced by a highly competitive climate created by the exploration boom in Australia. The influence of overseas methods and approaches have been married to the Australian techniques resulting in a management climate which is not only familiar with the technical aspects of exploration, but is also familiar with the personnel, economic and legal phases associated with the expenditure of very large sums of money. The utilization of all the geosciences coupled with mathematical models and computer techniques for pre-selection and assessment of areas are now normal aids used in management decisions. Management techniques developed and being developed will ensure that successful exploration will be carried out if sufficient incentives are guaranteed.

Jan 1, 1974

The progress of longhole open stoping (LHOS) at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) is described. The design of a novel sloped wall longhole stoping method at NBHC which should allow the cuplete extraction of the orebody without the formation of pillars and with minimal dilution of the ore with sandfill is reviewed.

Jan 1, 1983

By B J. Fallon

This study used structural equation modelling (SEM) to develop a series of models to explain the impact of work-life balance on employeesÆ perceptions of job performance, job satisfaction, turnover intentions and absenteeism. The sample comprised 257 participants (108 males and 149 females) from a range of occupations and levels of seniority. In sum, the results clearly demonstrated that successful work-life balance is associated with higher levels of job performance and worker satisfaction and with decreased levels of absenteeism and turnover intentions. The data also lent support to the impact of employeesÆ coping styles, schedule flexibility and supervisor support on employeesÆ abilities to balance work and life. It is concluded that tangible benefits to an employerÆs bottom-line can be anticipated from organisational initiatives to assist employees to better balance their work and personal lives.

Jan 1, 2005

Tonnes per Hour - Kilowatts per Tonne Tonnes of Mesh Size Produced Kilowatts per Tonne of Mesh Size Produced - Terms often heard in discussions of grinding mill and grinding circuit performance. All of them only tell a partial story as none of them relate to a fixed reference or overall standard measurement. Tonnes per Hour gives the production rate relating it to a specified or desired rate set as a goal or objective. As such it does not take into account changes in feed size, product size or grindability. Kilowatts per Tonne which accurately stated is kilowatt hours per tonne brings power consumed into the picture which is related to grindability but still does not take into account changes in feed size and product size without which power changes do not necessarily reflect the complete effect of changes in Grindability.

Jan 1, 1978

Attention is given to three possible alternative structures namely corporate joint venture, partnership joint venture and unincorporated joint venture. A corporate joint venture involves the formation of a separate and distinct legal entity with limited liability. The shareholders of the Company will be the members of the consortium. A partnership joint venture involves the members of the consortium joining a formal partnership. The partners will conduct the business in common with each other and will share the profits and losses of the project activities. The partners will be jointly and severally liable. An unincorporated joint venture is distinct from a partnership. The members of the venture will not be jointly and severally liable. Taxation and accounting aspects are examined and an outline provided of a typical joint venture agreement. The two main advantages of an unincorporated joint venture are considered to be a favourable treatment for income tax purposes and a greater degree of flexibility when compared with the corporate joint venture and the partnership joint venture.

Jan 1, 1983

By Morley I. W

Offshore minerals legislation has been introduced to provide jurisdiction over the exploration and recovery of mineral resources, particularly petroleum, from the territorial waters and parts of the continental shelves adjacent to coastal states. Ratificat- ion of the 1958 Geneva Conventions on the Law of the Sea has provided some measure of international agreement amongst signatory powers. Because the relationship of the Australian States to the Commonwealth in their federal system, the Australian offshore petroleum legislation is of particular interest. The customary role of the States in mineral resources management, which has extended to the offshore, is under challenge from recent unilateral Commonwealth Government legislative actions in the fields of mineral resources jurisdiction. Environmental considerations provide an additional issue, as yet unresolved, with the delay in submission of the Report of the Great Barrier Reef Petroleum Drilling Royal Commissions

Jan 1, 1974

This paper describes some experiences in the design of flotation reagent schemes for the efficient flotation of complex gold ores containing free gold and/or gold associated with easily flotable sulphide minerals such as chalcopyrite and bornite. Historically, the design of gold flotation reagent schemes has been based primarily on experiences using high dosage levels of water soluble charged collectors such as xanthates and dithiophosphates and carefully controlled regions of pH. This approach has been effective with gold associated with complex sulphide minerals, in particular gold associated with iron sulphides such as pyrite. An alternative two-stage reagent approach is presented that is applicable to certain types of gold ores. This approach involves using very small dosages of uncharged water insoluble collectors at natural ore pH followed by a modified bulk flotation reagent approach for the second stage. The reasons for utilising this approach, when applicable, are discussed and illustrated with examples.

Jan 1, 1997

As an Inspector of Mines in Queensland, my main responsibilities include the enforcement of the Mining Act 1968 - 1986, the Mines Regulation Act 1964 - 1989 and the Metalliferous Mining regulations 1989 to promote the safe and responsible exploitation of the States' mineral wealth.An important adjunct to this task is the offering of an advisory service to the mining industry. However, in the pursuit of my duties to this regard, I have sadly observed in some cases, numerous wrong doings and negative activities by miners which have led to their ultimate demise, not to mention that of others. Despite what I consider corrective advice, I have witnessed, again in some cases, disregard and blind pursuit for the wrong end.This then is a novel approach to get the message home in the form of a light hearted cartoon presentation relating the saga of an average Aussie battler entering the mining game unprepared, making the wrong decisions due to his own ignorance and the cleverness of others, leading finally to his and possibly others' downfall.

Jan 1, 1990

By Sijing Cai, Chengpu Zhou

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By McNicol J. H

Using a small scale laboratory pilot plant a series of tests have been conducted with the aim of investigating the influence of the zinc/acid ratio on the efficiency of zinc electrodeposition from an acidic sulphate solution. The results have shown that current efficiency is increased as the zinc/acid ratio is increased with no evidence of an optimum zinc/acid ratio. However the choice of a zinc/acid ratio for full scale operations must be a compromise between other parameters, spent electrolyte acidity and power efficiency, which also impact upon plant performance. The effect of various impurities has also been monitored and antimony, nickel and tin have been shown to be deliterious to current efficiency.

Jan 1, 1989

By Tyler MA

If the record of maj or proj ects in Australia is taken into account, it is apparent, the proper planning of an industrial relations strategy for many such projects has been ill considered by project developers. The recognition of the need to develop a plan from the initial feasibility study has been forced on those promoting new projects by the publicity given to the Australian industrial relations record. The delays in delivery caused by factors supposedly out of the project's control are often given for non-performance of contract and used as an excuse for limiting further development. Many of the problems experienced in project development can be overcome with sound industrial relations planning. The promises given in the euphoria of the early stages of a project relating to price and delivery often become a burden for the future because the complexities of the Australian Industrial Relations Systems are not understood or considered. The recognition by senior executives of their responsibilities in this area will contribute greatly to a new era of project development.

Jan 1, 1983