Search Documents

To provide suitable backfill material for the cut and fill mining method being used to extract ore from the C.S.A. mine, flotation tailings are deslimed in single stage cyclones. The sand fraction is stored on the surface in unagitated storage bins before being pumped underground, while the slime portion is thickened and pumped to a residue dam. Design and operating details of the sand preparation and storage sections are given.The initial preparation of a stope for filling, consists of laying percolation and decantation drainage pipes on the sill floor. Preparation for fllling of subsequent lifts consists of rearing up the ventilation pipes at the ends of the stope, preparing the decantation system, and building a barricade or wall. The fill is carried to, and discharged into, the stope through 4 in. diameter pipes and filling of any section is carried out 24 hr/day normally without supervision. The fill is retieulated underground to the 1200 ft level through rubber lined pipe installed in the upcast shaft. Boreholes of 3 in. diameter drilled from the1200 ft level convey fill to the 1800 ft level. The mine drainage system is basically designed to handle the water associated with hydraulic filling. A system of primary and secondary sumps has been installed to handle the percolation and decantation drainage from stapes and to allow settling of fines before the water is fed to the main pump station.A programme of investigation into the properties of the emplaced fill is in progress. Results to date indicate that the fill as presently placed and drained, will not cause any problems in the mining of vertical orebodies by cut and fill methods for lifts in excess of 300 ft.

Jan 1, 1969

By Getliffe RK

It is becoming more and more difficult to operate mineral and metal processes profitably, as operating costs rise, quality demands in-crease, international competition becomes more fierce and Government charges remain at their current levels. Profitability today depends upon efficient operations, which can only be achieved through precise and dependable con-trol of each process unit comprising thetotal plant.Modern process control systems utilise distributed architecture with microprocessor-based controllers, data acquisition devices and VDU operator stations. Honeywell intro-duced this control technology in 1975 with the "Total Distributed Control" System. Now, building on the proven performance and re-liability inherent in TDC hiway modules, Honeywell has extended the TDC system to inte-grate both management information and control by providing distributed processing modules on the new TDC 3000 Local Control Network (LCN).

Jan 1, 1985

By Watson DF

Calculation of the amount of metal in an ore deposit or mining block should be approached by multiplication and integration of appropriate numerical manifolds describing the spatial distribution of the relevant variables, viz. grade, specific gravity and also thickness for bivariate data. Construction of a numerical manifold necessarily involves some form of interpolation but detailed characteristics of this are often not specified in various automatic methods, some of which even provide manifolds with discontinuities. A manifold used in calculations should describe in a geologically plausible way the spatial distribution of the variable of interest. Different approaches to the problem are discussed and compared. Particular computational inconsistencies emerge when "accumulation" is used as a variable in calculations of average grade. If an ore deposit is variable in relation to its sampling and especially if selection of mining blocks according to grade cut-off is a necessary operational decision, the biases introduced by accumulation methods can bring about serious problems of over-evaluation. Modern computational techniques make unnecessary the use of accumulations; because of potential inconsistencies it would seem unwise to use them in any ore reserve computation.

Jan 1, 1987

Giving the keynote address in the final session of a conference dealing with closely related topics has a disadvantage in that much of what can be said has been said. It also has an advantage, however, because it presents the speaker with the opportunity to integrate and analyse the material presented by the various speakers. I would like to look to the near future in Aust- ralia and the United States of America, to the risks, problem areas, and changes of a rapidly evolving post-industrial era-an era we are begin- ning to experience where industry no longer `calls the tune'. We miners have been quick to point out and emphasize, that ours is a `high-risk' industry in the world of business and commerce. Yet, clearly those who have survived, and been successful, have learned to anticipate and cope with risk and change. This ability has been a distinguishing feature of the industry's leaders who, in market studies and commodity selection, exploration and development, mine planning, metallurgical pro- cessing, and general administration and operation 1. identify areas of risk or inevitable change, 2. analyse, test and quantify those factors of risk or change, and 3. design methods, systems, equipment to elim- inate, moderate, or control or economically compensate for predicted risks or changes.

Jan 1, 1978

This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of "ownership" as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management.The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor's estimate of "best practice". The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to "best practice" outcomes in comparable process industries.

Jan 1, 1998

Powercoal Pty Ltd operates eight underground coal mines in New South Wales and produces coal for both domestic power stations and the export market. Approximately 40% of total production is from continuous miners. Over the past five years, place change mining methods have been introduced to improve productivity from continuous miners. This has involved utilising the existing coal clearance system from the continuous miner to the ratio feeder using trailing cable shuttle cars.By late 1996 average productivity at Cooranbong Colliery using this system had plateaued at 800 tonnes per eight hour shift. A number of factors were identified to increase average productivity to 1500 tonnes per eight hour shift. An improved coal clearance system was one of the factors identified.

Jan 1, 1998

By Stuedel J

Starting from comprehensive programme systems for monitoring tasks of any kind, this paper follows the steps of the programme system hierarchy from top to bottom. The monitoring and control centres for entire production units, the subordinate centres, i.e. district control centres, the microcomputer based autonomous control systems, and data input by mobile terminals are discussed. To an increasing extent, the main emphasis is shifted from monitoring and control of individual machinery to optimized operation of extremely complex comprehensive systems. Network displays, for instance displays of production, transport, supply- and evacuation-networks as well as of safety systems, gain increasing importance. Personnel deployment systemsand planning networks as well as stocktaking and accounting are more and more closely linked with the above-mentioned networks. In order to keep development and application (purchasing) costs low, and to assure compatibility, the use of standard modules is to be assigned particular importance. New module developments are introduced, and the design of standard interfaces for computer and module coupling are discussed.For conclusion, a short view is given on the opinion of the line manage-ments on how future hierarchic systems should be featured in terms of individual units and overall systems, and used.

Jan 1, 1985

By D Bradshaw

The recovery of molybdenum at Kennecott Utah Copper (KUC) has become increasingly important as its demand and price have risen dramatically in the last few years. Consequently, the flotation behaviour of the molybdenum bearing mineral, molybdenite, has received a significant amount of attention. The flotation performance of molybdenite generally lags that of the copper sulfide minerals and is much more variable. There are many factors including particle size, liberation, surface slimes and oxidation that contribute to this and also much speculation as to the relative contribution of each of these factors. This paper discusses the morphology of the molybdenite found at KUC, the mineral associations in the different lithogical ores types and the effect that each of these has on flotation performance. Quantitative mineralogical analysis and an assessment of particle shapes are used to explain that flotation behaviour does not necessarily follow expected trends and that some behaviour is counter-intuitive. This unique behaviour can be explained by the morphology and anisotropic nature of molybdenite.

Jan 1, 2008

In 1989 Henry Fairlie wrote a cover story for The New York Republic, 'Fear of Living'. He noted, `The first Apollo space craft caught fire during a test on the launch pad. Three astronauts were killed, the nation was shocked and horrified, all the more because the screams and scrambles of the astronauts could be clearly heard'. After a brief delay in manned flights, the Apollo program resumed with strong public support; within 18 months, Apollo 11 landed on the moon. Fairlie contrasts the Apollo tragedy to the 1986 Challenger disaster. `The prevailing mood in America so panicked NASA that it took almost three years to send up another shuttle', he observed. `In 19 years between these tragedies, the idea that our individual lives and the nation's life can and should be risk-free has grown to be an obsession threatening to create an unbuoyant and uninventive society.' Taking risks is a normal part of our daily routine. The act of living involves minute-by-minute decision-making focused on survival through the practical management of risks. The act of breathing exposes each individual to the risk of infection while the act of crossing the road could almost be considered suicidal. We deal with these constant threats by observing simple rules of hygiene, safety or what may be labelled as common sense. The rules of community, designed to minimise risk in society, can at times lose focus and result in the imposition of schemes that have a far greater cost than the issues from which they protect. Effective management of risk, whether in the community or a business is about awareness and balance and the elimination of unacceptable risk. Risk cannot be eliminated from our lives or our working environment. However it can be managed if it is properly understood, monitored and controlled. The purpose of my presentation today is not to provide a comprehensive technical risk inventory but to capture the essence of risk and the application of management strategies designed to deal with it in a positive fashion. The basis of our differential financial reward system is risk. The key to successful management is to deal with the downside risks in such a fashion that the benefits of enterprise are not eliminated. The key question any investor must consider is `can the major risks assQciated with a venture be managed or eliminated while retaining a greater proportion of upside potential'. The answer to this question is the ultimate value an investor would assign to any project. In reviewing the relevance of risk to our industry the range of papers to be presented today provide examples of how management deals with specific components of risk. In each case the value of the business has been enhanced by the practical application of balanced risk management. The ultimate success of the industry depends very much on this concept as it also provides a public showcase upon which we are judged. Therefore, from all perspectives the effective management of risk is a cornerstone from which to build a stable and progressive mining industry.

Jan 1, 1994

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

There are significant Mineral Resource and Reserve reporting challenges facing a mining company operating in the global arena. This paper specifically examines the Mineral Resource and Reserve reporting challenge facing BHP Billiton. The changing regulatory environment creates a significant challenge for global mining companies when reporting Mineral Resources and Reserves. The development and implementation of internal policies and standards for collecting and collating resource and reserve information is required for corporate governance, however the challenge is then to report this information publicly in such a way as to comply with the various codes and requirements in the many jurisdictions in which the company is required to report. The move to an International Code is not only desirable but is an essential requirement in todayÆs global market. The agreement to report using a single code internationally is however only the first step. A truly practical international reporting system must have common definitions and guidelines for interpretation as well as an international approach to the definition of a Competent Person, and even more importantly a common acceptance of that code by the relevant investment regulatory bodies. Without the universal acceptance of the concept of an international reporting code by the major regulatory bodies, implementation of such a code will be limited. With the major global mining companies seeking to raise capital in the USA, the worldÆs largest capital market, the Securities and Exchange Commission (SEC) and its approach to reserve reporting is becoming increasingly important. The development and implementation of an International Code must gain the support and acceptance of the SEC if it is to be successful.

Jan 1, 2002

Scale build-up in titanium palladium alloy spent electrolyte heat exchangers in the residue treatment plant commissioned at Risdon, Tasmania in 1971 was shown to be a mixture of manganese dioxide and anhydrite (CaSO4). The manganese dioxide was deposited as a result of thermal decomposition of permanganate ions present in the spent electrolyte. It was shown that deposition of manganese dioxide and associated anhydrite scale could be prevented by prior reduction of permanganate ions to the manganous (Mn++) state by the addition of ferrous ions. In the plant this was conveniently accomplished by injecting into the inlet line to the heat exchangers sufficient zinc plant solution containing ferrous sulfate to decolourise the spent electrolyte. This action prevented deposition of such scale for another 21 years, until the heaters were finally decommissioned in March 1992. Measurements indicated that addition of the reducing solution lowered the anodic potential of the titanium alloy by 200 - 300 mV (depending on the solution resistance), but that it was still +300 to 400 mV with respect to a standard calomel electrode. It was shown that, if necessary, a small impressed current could be applied to provide anodic protection. Before scale deposition was overcome by the addition of ferrous sulfate solution, badly scaled heat exchangers were cleaned by recirculating a solution of hydrogen peroxide in spent electrolyte or dilute aqueous sulfuric acid, after laboratory testing of a variety of possible solvents for the scale. Corrosion tests indicated that attack on the titanium alloy by the acidic peroxide cleaning solution was insignificant.

Jan 1, 2005

New Caledonia is a major metallogenic unit of the south-western Pacific Rim. Its mineral production is of world significance and it has an unusually well diversified mining history. New Caledonia's main metallogenetic potential is, however, associated with its unique ophiolitic complex and its important mineral- izations of nickel, chrome, cobalt and iron. Gold has been found in all the four basic tectonic elements of New Caledonia: the Central Massif, the West Coast basalts, the ophiolitic complex and the Caledonian North. Some analogies are attempted. Only the Caledonian North has supported mining operations (213 kg Au). More recently tenuous gold indications have been found within the ophiolitic complex, possibly associated with Oligocene plutonism.

Jan 1, 1987

Here, in what is partly a review and partly a personal viewpoint, I take stock of changes in emphasis and comprehension on the subject of basaltic volcanism in the decade that has passed since the completion of the landmark Basaltic Volcanism Study Project (1981). I concentrate attention on the relatively neglected physical-volcanology aspects (in 1988 it was still possible to publish a 340-page book on flood basalts with barely any mention of physical mechanisms).I adopt the useful unifying concept of "volcanic system" to embrace the invariably-present intrusions as well as the volcano; I consider controls exercised by magma-supply rate and modulator-mechanisms on the nature of the system;I emphasize that sheeted-intrusion complexes, consisting either of dikes or inclined sheets (depending on the ability of the system to expand laterally) occur in all eroded major systems and fuel geothermal systems; I show how constraints set by cooling of narrow intrusions cause such complexes to be wedge-like and produce considerable rotations; I consider the role of the level of neutral buoyancy in making magma chambers possible, causing lateral subsurface magma flow and localizing intrusions, while the LNB itself can be accentuated by intrusions; and I examine the possibility that underwater systems could have very different internal structures from systems on land.

Jan 1, 1990

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

Felspar occurs in association with quartz in the Broken Hill lode pegmatites and is brilliant green, greenish white, and white in colour. The pegmatites occur mainly in the walls in sporadic patches, parallel to the general dip of the ore deposit. The occurrences are of no economic value.Deposits of marketable felspar occur in pegmatite in a number of localities around Broken Hill, New South Wales.The majority of these are in the form of an irregular outcrop, usually of tapering length and depth. The maximum depth of any deposit yet worked in the district is about 40 ft. The felspar is occasionally contaminated by "blows" of quartz, mica and beryl, but the two latter are profitably marketable when separated.Felspars vary in colour from pink, through grey to snow white, and the colour is not indicative of the mineral content. The largest deposit at present being worked is the Egebeck quarry, about 14 miles south of Cockburn. It is a prominent outcrop, roughly circular and about 150 ft. in diameter, covered by one to three feet of overburden.The felspar is mainly massive, but contains some cleavage planes at approximately 90°. Intrusions of quartz and mica occur in patches, but the deposit appears likely to improve in size, regularity and quality below the present working floor.COMMERCIAL USES.Commercial felspars are mainly used in the ceramic industry, for which a high-grade potash felspar is required.The dental industry requires limited amounts of soda felspar with a very low Fe20s content. The poorer grades...

Jan 1, 1946

By J A. Brown

Osborne Mine commenced hydraulic filling of three stopes in April 1999. Two of these stopes experienced barricade failures in July 1999 and January 2000. As a result, a review of hydraulic filling was commissioned in April 2000. The design of a trial of revised specifications and practices is in the final stages, prior to the trial commencing in mid-2002.

Jan 1, 2002

Since the initial discovery of phosphate rock resources in North West Queensland in 1966, significant changes in ownership and development direction have occurred. Initially development of the resource involved beneficiation to produce a more saleable grade of phosphate rock. However more recently development has focused on the production of a high analysis fertilizer product on the minesite. These changes have been influenced by economics, industry/government cooperation and a changing phosphate industry.

Jan 1, 1998

By Golosinski T. S, Jorgenson J. D

Several methods are available for inspections of mine shafts. These involve use of inclinometers, moving beams, inertial platforms and decelerometers. Inspections which use decelerometers are of most interest since they allow assessment of conditions of shaft steelwork, conveyances and the shaft itself. This assessment is based on recording and analysing dynamic behaviour of shaft conveyances. Sample inspections of several WA shafts confirm feasibility of using this method for periodic shaft Inspections.

Jan 1, 1995