Search Documents

By M Kilburn, A Edenton, M Adam, A Dehghan-Manshadi, R Smyth, L Lu

The blast furnace is a counter current reactor. The counter current principle of the furnace makes it very efficient in transferring the heat and mass required to drive the reduction reactions inside the furnace. However, this does impose a stringent requirement on the permeability of burden material in the furnace. Lump ore is one of the key ferrous feeds used in the blast furnace ironmaking process, often accounting for ten to 20 per cent of the blast furnace ferrous burden. As the lump ore descends through the blast furnace, it is dried, heated and reduced by the ascending hot reducing gas. To ensure good furnace permeability, generation of fines from burden materials including lump ore due to mechanical, thermal and chemical processes needs to be minimised. Unlike sinter and pellets, lump ore is subject to thermal degradation. To assess this behaviour of lump, the ISO decrepitation test (ISO 8371, 2007) is often conducted, and the result is calculated as a decrepitation index (DI). However, the DI values obtained from the existing ISO decrepitation test vary considerably between test portions and between laboratories, which makes meaningful comparison very difficult. In order to identify the sources responsible for the unacceptable repeatability, the effect of various testing conditions, such as particle size, heating rate, sample preparation and loading method, on the mean DI value was studied. The mechanisms contributing to thermal degradation in the top of the blast furnace and during the standardised decrepitation test are also discussed.CITATION:Lu, L, Kilburn, M, Dehghan-Manshadi, A, Adam, M, Edenton, A and Smyth, R, 2013. Thermal degradation of lump ore in the top shaft of blast furnaces, in Proceedings Iron Ore 2013 , pp 421-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Smith DM Jr

Silver deposits, in which silver forms at least fifty percent of the value of the ore, are abundant and large on the east side of the Pacific and are absent in the western Pacific. To determine if this uneven distribution is related to features of consuming plate tectonic boundaries which dominate the metallogeny of the Pacific Rim, the variation of Ag/Au in porphyry copper deposits was used to estimate the relative silver content of magma generated in subduction zones. Porphyry copper provinces with high Ag/Au occur in regions of the eastern Pacific where silver deposits are abundant, suggesting that the distribution of silver deposits is controlled by the relative abun- dance of silver in subducted ocean crust. Ocean crust being subducted in the eastern Pacific is mostly less than 50 million years old in contrast to most ocean crust in the western Pacific which is much older. Enrich- ment of silver in young ocean crust at spread- ing centers may reflect metallogenetic evolution over geologic time. Silver may be transported to the surface in volcanic rocks, and deposits are common where felsic varieties are abundant. The high ,solubility of silver in natural waters provides a natural storage mechanism for silver weath- ered from these rocks and ultimately circulated in near-surface hydrothermal systems where many silver deposits form. The regional distribution of silver deposits is not influenced by discoverability, vertical metal zoning, or regional tectonic style. The effect of igneous differentiation is unclear.

Jan 1, 1987

An image analysis system has been built which automatically digitizes camera input of rock fragments, analyses the digitised data to determine the sizes and shapes of the rock fragments, and outputs the analysed data to a printer in the form of a histogram or a scatter chart. The high speed of such a system allows for direct collection of data from material thrown into the air by blasting, material travelling on a conveyor belt, and material free-falling on to a stock-pile or into or out of a rock-crusher. Data on the blasted, un-crushed material provides information on changes in the lithology and structure of the rock face as it is quarried or mined: flatter fragments may represent approach to a brittle, unstable shear zone, or a change from sandstone to shale; so that the informa- tion reflects the effect on the sizes and shapes of the fragments by the blasting process and/or by the rock structure. The size and shape distributions of rock fragments produced during blasting and during processing may now be continuously monitored. Such detailed analysis of the results of fragmentation is labour-intensive and expensive when the size and shape distributions are obtained manually, but is cheap and efficient when using this image analysis system. Such a system will enable the results of blasting, quarrying, mining and crushing to be cheaply analysed and correlated with current and changing indus- trial practice so leading the way to increased productivity.

Jan 1, 1988

By C Ward, U Mueller

Compositional geostatistics is an approach developed to ensure that the constant sum constraint induced by geochemical iron ore analysis is respected in estimation and simulation. Jack-knifing and cross-validation were used within this framework to compare the results from ordinary cokriging of the additive log ratio (alr) variables with those from conventional ordinary cokriging. Two methods were used to back-transform the alr estimates: the crude additive generalised logistic back transformation and numerical integration via Gauss-Hermite quadrature. Previous work on a blasthole data set from a Yilgarn iron ore mine showed promising results, with the Gauss-Hermite quadrature method returning results comparable to ordinary cokriging from the point of view of bias, but superior in that the constant sum constraint imposed by geochemistry of the data was honoured. Other practitioners have noted that the linear interpolation of non-linear log ratio transformations will result in biased results, and that this bias can be masked in a (grade control) setting where the spatial density is high. To test this assertion, the methodology has been extended to successively lower spatial density data sets. The results and applicability to routine iron estimation are discussed.CITATION:Ward, C and Mueller, U, 2013. Compositions, log ratios and bias - from grade control to resource definition, in Proceedings Iron Ore 2013 , pp 313-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Platinum Group metals have been known in New Zealand since the 1880's but not produced on a large scale. They have been neglected because their value was not appreciated rela- tive to gold and their value was often very low, reflecting demand, and because recovery was difficult compared with recovery of gold. With the rising price of most Platinum Group metals and the perfection of gravity and flota- tion recovery methods, recovery of platinum along with gold from alluvial deposits is more attractive. Platinum Group metals are known in several different environments in New Zealand, ranging from alluvial placer deposits to layered basic to ultrabasic intrusions and quartz veins. None of the known occurrences have been ade- quately prospected and there is a real possibi- lity of future discovery of important deposits. Several New Zealand based and at least two offshore resource companies are currently involved in exploration, prospecting or mining for Platinum Group metals in New Zealand.

Jan 1, 1987

This paper carries on from an earlier paper 'Cemented fill practice and research at Mount Isa' and reports further on the laboratory programme at Mount Isa to develop a cheap cem- ented fill using Company waste products. The practical economic significance of availability of cheap cementing agents is re- viewed, with the various alternative approaches available The basic approach adopted within this paper is that use of reactive pozzolans such as ground slags to replace a proportion of the Portland cement in the fill can make mining methods employing cemented fill more economic- ally competitive with other mining methods.

Jan 1, 1973

By S Smith

Several styles of copper (Cu) mineralisation are present at Sepon. Large tonnage, low grade skarn and carbonate replacement massive sulfide mineralisation occur within the metamorphic aureole of Permian-aged rhyodacite porphyry intrusions (RDPs). During exhumation and supergene weathering, this primary mineralisation has been upgraded to form high-grade chalcocite enriched zones up to 50 m thick, which comprises the bulk of Cu resources currently being mined at Sepon. Groundwaters remobilise Cu to form exotic accumulations of malachite that are locally hosted in irregular karsts in carbonate rocks, found up to 1000 m from source mineralisation. Khanong is the largest Cu deposit and recent discoveries have been made at Thengkham South, Thengkham North and Phabing. All deposits have formed by similar processes of mineralisation. However, all differ due to local variations in host rock lithology, structural setting, and hydrological conditions. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The stratigraphy of the Singleton Coal Measures is reviewed and a revised stratigrapixy which has been ratified by the N.S.W. Standing Committee for Coalfield geology is nominated and defined by a selected type section. Withir the type section the occurrence of repetitive phases are illustrated and described. Coal. Measure units within the Singleton Coal Mean sures, termed the Wollombi and Wittingham Coal Measures respectively, are correlated with the Newcastle and Tomago Coal Measures. In formal nomenclature the Singleton Coal Measures are designated the Singleton Super Group. The major depositional cycles within the Coal Mea- sures are outlined together with those lesser phases within the Coal bearing sequences that influence the mining conditions likely to be encountered. Both tectonic and sedimentary features of the Singleton Coal Measures are considered and the localized post depositional effects on the coal seams and roof strata in- duced by differential, compactions are emphar Sized.

Jan 1, 1972

By P M. Downes

Porphyry-related skarns are common around thePacific Rim. Examples include Cadia and Goonumbla (Australia) Ok Tedi (PNG) and Ertsberg and Grasberg (Indonesia). Although usually treated as separate to the adjacent porphyry copper-gold (Cu-Au) deposit, skarns near porphyry deposits are commonly inextricably part of the larger Cu-Au system(s). Using Cadia as the primary example, we demonstrate that large, zoned, calc-silicate skarns necessitate very large porphyry systems. The Big Cadia and Little Cadia Fe-Cu-Au skarns are associated with the Late Ordovician to Early Silurian high-K calc-alkaline to shoshonitic Cadia Intrusive Complex (CIC). Together, these skarns total ~40 Mt of Cu-Au ore but are much smaller than the adjacent Cadia EastûFar East, Cadia Hill, and Ridgeway porphyry-related Cu-Au deposits. Historically these skarns were large, economically significant and highly controversial deposits. Porphyry-related skarns typically have well-developed calc-silicate and ore zonation. At Cadia, classic skarn zonation has been mapped between Cadia Quarry (proximal) and Big Cadia (distal). Over this 800 minterval, mineralogy trends from: proximal garnet > pyroxene, grading to; fe-oxide-rich skarn; and distal haematite-epidote-rich skarn. At Little Cadia, analogous but symmetrical alteration zonation is present. Big Cadia formed from fluids that migrated laterally within calcareous units and were sourced from strongly altered quartz monzonite phases of the CIC at Cadia Quarry. Isotope studies and mass-balance calculations suggest that prograde and retrograde skarn alteration was caused by magmatic dominated fluids. They also indicate that the mapped alteration system at Cadia Quarry is insufficient to account for the total volume of Fe present at Big Cadia. Despite the typically oxidised nature of many porphyry systems, not all skarns in the porphyry environment are oxidised. Assimilation of carbonaceous sediment by hydrous, alkaline intrusions could lead to reduced Au skarns rather than porphyry deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Dunne R. C

Column flotation is receiving increased interest from both an industrial and research perspective in Australia. The traditional overseas application as a molybdenum cleaning cell is being expanded and a number of new applications as cleaners, scavengers and roughers are emerging in Australia. The success of column flotation has hinged on the new understanding developing from the work of Finch- and coworkers at McGill University, Canada, particularly in relation to scale-up parameters and model development. The aspiring column flotation user in Australia now a has wealth of experience to draw on when deciding on the correct procedure to follow during the process evaluation and plant installation stages of development. However, some aspects relating to column design, such as aeration mechanisms, require careful evaluation.

Jan 1, 1987

The ownership, policies, organisation, structure, market, financial considerations and communications of a large resource project vary significantly through its discovery, feasibility, development and production phases. The extent of these changes, from discovery in 1957 through to 1979, is examined for the Mt. Newman iron ore project in the Pilbara region of Western Australia and some of the factors that influenced it are detailed. This shows that only some of the influences are under the control of the mine owner/operator, despite their significant impact on the returns for the massive capital invested. The effect of the general business climate on the various phases is also examined.

Jan 1, 1980

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electro- lyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions. The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was invest- i,ated as a method of optimizing glue additions in the presence of antimony. Scanning electron microscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltammetry measurements showed some correlation between current efficiency and activation polarization potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1984

By Mostyn G

In the last three decades various theories have been presented to allow the estimation of the force required to cut rock. These have generally relied on an hypothesised mechanism of chip formation.The paper presents results of an experimental program completed on an unjointed artificial rock in which the force and chip geometry were measured during deep cutting with a quarter scale bulldozer tyne. The program included various depths of cut and artificial rock of varying strength. The experimental results are compared with predictions based on three expressions for cutting force. Generally the measured forces are within the range of those predicted but none of the methods predicts the cutting force with any accuracy. It is considered that the discrepancies are due, in part, to the fact the that actual shape of the chip formed in deep cutting is quite different to that assumed in developing the theories and thus the theories cannot be expected to predict the cutting forces. It is concluded that Evans and Nishimatsu's theories predict lower bound estimates of the horizontal cutting forces. Deliac and Fairhurst's approach appears to over estimate the forces required to cut rock. New methods of prediction are required based on the observed mechanisms of failure.

Jan 1, 1993

By F Sandrone, J-P Dudt, J Zhao, E Paltrinieri

Tunnel boring machines (TBMs) excavation is nowadays more and more considered a valuable alternative to conventional tunnelling. As a matter of fact, thanks to its advantages such as greater rate of advance and safer working conditions, the application of TBMs has increased significantly in recent years. Despite the possible excellent performance of TBMs in favourable ground conditions, the advance rates could be significantly slowed down or even obstructed in limiting geological situations. This obviously traduces in potentially longer tunnel construction times and higher costs and, therefore, in a preference for conventional method. One of the major geological hazards encountered during tunnel construction, is related to the presence of fault zones or heavily jointed and fractured rocks. The most common geotechnical problems resulting from tunnelling in these difficult conditions include the instability of the excavation face, instabilities of side-walls producing large overbreaks on the tunnel profile, excessive deformations in case of squeezing grounds, frequently changing stresses in terms of magnitude and direction, high water inflows, etc. The decisions aids for tunnelling (DAT) is a model and a computer code that can be used to evaluate the influence of the uncertainties related to both the geological/geotechnical conditions and the construction process on final tunnel construction time and costs. In this framework, the DAT is used for assessing the effects that challenging ground conditions may have on tunnelling operations in terms of costs and delays. This is done by simulating the tunnel construction considering several geological profiles. The aim of the study is comparing different excavation methods (ie drill and blast versus TBM) in changing ground conditions along the tunnel alignment ranging from good rock, to very poor and fractured formations. The results show the impact, in terms of changing construction time and cost, of the excavation method versus the ground conditions.CITATION:Paltrinieri, E, Dudt, J-P, Sandrone, F and Zhao, J, 2014. Comparison of excavation methods in different ground conditions with the decision aids for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 573–580 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

In todayÆs demanding business landscape continual change and technological advancement is a given. With these changes there is now, more than ever, a need to ensure sustainable growth in respect of value protection and value adding whilst meeting the pressures and expectations of the societies in which we operate. Traditionally the management of safety has been a very reactive activity in the business, in some cases seen as an irritation and a disruptive process that demands a focus on preventing reoccurrences. This in turn has focused the measurement of safety performance on a range of lagging indicators û æafter the effect managementÆ. Gaining and maintaining a licence to operate is crucial to a sustainable business but as a prerequisite, organisations need to have a demonstrable ability to manage the safety of their people, as well as mitigating the people risk associated with the business activity. A major focus in the last decade has been on the implementation of enterprise risk management programs, where risk becomes embedded in all business systems and processes and the organisationsÆ genetic make up is programmed to analyse and integrate risk management into all facets of the business activity. The management of safety should be no different. One school of thought argues that there are no new accidents, but rather our inability to learn from the past. Others believe that as long as we have an appetite to achieve the unachievable, we will have to continue to push the boundaries, our safety comfort zones and inevitably take risks. Single reliance on highly evolved technical systems, elaborate processes, highly skilled people, safe equipment and safe work environments have shown one thing û they are not sustainable in providing adequate coverage in the business. In analysing a range of factors associated with some of the worst catastrophes of the 20th century, it can be suggested that they were in fact predictable and inevitable and that an integrated approach underpinned by sound risk management systems could have determined a different result. The key to a sustainable approach in the management of safety requires us to look at a multitude of aspects that collectively allow the performance of an organisation to be predictable. To have certainty in the business activities it is necessary to have controls in place that will mitigate the risks normally associated with unwanted events. It is ensuring that human factors effectively contribute to monitoring the planned approach and being able to safely adjust to any variability. In essence this is having the ability to proactively plan for the longer term. The sentiments articulated by organisational leaders echo that safety management is good business. Surely then a good business is a sustainable business, and a sustainable business is one that provides lasting benefits to its stakeholders.

Jan 1, 2006

Taiwan is situated between Ryukyu and the Philippines with 35,960 sq. km of area, being slightly larger than Belgium It has roughly a spindle-shaped outline with a longitudinal axis extending in a roughly north-south direction. Geologically, Taiwan is extremely complex in terms of its tectonic setting in the convergence zone between the Asian continent and the Philippine Sea Plate. To the east of Taiwan, the Philippine Sea Plate subducts beneath the Ryukyu island arc, and to the south of Taiwan the Philippine Sea Plate overrides the Asian plate along the Manila Trench. Taiwan, therefore, occupies an unstable region between these two well-defined subduction systems of opposite polarity (see the following block diagram).

Jan 1, 1987

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

By G Ride

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in arid areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1971

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

By J Rostami, D Tadic

While hard rock tunnel boring machines (TBMs) have an established track record in the tunnelling industry, accurate estimation of TBM performance for each specific project remains critical. Machine performance prediction is required to assist planning activities, including costing and schedule preparation, machine specification and effective planning of maintenance and repairs. In addition, monitoring machine performance during the construction period is required to assess and manage excavation progress, and to achieve optimal advance rates based on specific geotechnical conditions exposed during excavation. TBM performance analysis can also contribute to the development of more accurate performance prediction models for future applications. Rock mass characteristics play a dominant role in machine performance. This paper offers a review of the impact of rock mass characteristics on TBM penetration rates for two specific tunnelling projects. A discussion is provided on the results of statistical analysis of available field data, including geological back mapping, rock properties and measured rates of penetration (ROP). The analysis offers a comparison of the achieved and predicted ROPs to provide a better understanding of the influence of rock mass properties on the performance of hard rock TBMs. A new rock mass adjustment factor is introduced to enhance the accuracy of an existing prognosis model for use in jointed rock masses.

Jan 1, 2008