Search Documents

The Coal Corporation of New Zealand Ltd (CoalCorp) is the largest coal producer in New Zealand, with extensive properties in both the North and South Islands. CoalCorp's North Island operations are kilcmetres to the south of Auckland. opencasts, are located in the catchment wildlife, historical and scenic values. in this catchment is the single most mining operations. centred on Huntly, a town some 80 Five coal mines, four of which are of Lake Waahi, a lake with significant The discharges of mine lodgement water important environmental constraint on Throughout New Zealand the use of water is controlled by a statute called the Water and Soil Conservation Act 1967. All industrial water users are required to hold Water Rights, which are in effect licences to take, use, dam, divert or discharge water. Water Rights are obtained through a legally defined process and any potentially affected party has the per to object to their granting. A special tribunal hears the evidence for and against an application, and issues its decision, which is reviewable in a higher court on Appeal. Rights, if granted, are issued subject to conditions and, in the case of mining discharges, limits would be set on flaw rate, suspended solids concentrations, turbidity, pH and the concentrations of any potential toxicants. This paper presents a case study of an integrated, catchment wide water management plan for Lake Waahi, that was prepared by the author, and others while the author was in the employ of CoalCorp, and its predecessor, State Coal Mines. The author is grateful to CoalCorp for their permission to submit this paper.

Jan 1, 1988

By Houlihan RN, Landau J

A reciprocating plate column is described in which two sets of perforated plates are mounted alternately on two shafts and are reciprocated with a phase difference of 1800 between them. It is shown that such a column is mechanically superior to the previously proposed types: under practical operating conditions the pressure fluctuations at the base of the column are only a small fraction of the static head. Furthermore, mass transfer experiments with the system tributyl phosphate in kerosene- acid aqueous solutions of uranyl nitrate show that both high specific throughputs and reason- ably good efficiencies can be attained in this type of column. A comparison with the more conventional extraction equipment (mixer -settlers, pulsed columns) on the basis of residence time per equilibrium stage indicates the potential of reciprocating plate columns in hydrometallurg- ical application, especially in which the requirements of separation efficiency are modest while the scale of operation is large.

Jan 1, 1975

By Townsend MG, Evans RB

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre- Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth.The raw material is crushed and fractionated to produce a product of less than 2 micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

Market forces, particularly iron ore prices, demand that plant operators achieve higher throughput in the worldÆs iron ore beneficiation plants without compromising yields or efficiency. This means that production cost per ton is of paramount importance and that all major pieces of Processing Equipment have come under close scrutiny to improve throughput at their most efficient performance levels and for the longest possible continuous running time. Without doubt the use of modern engineering standards and materials of construction has contributed to matching these throughput, efficiency and availability demands. However, often not enough attention is paid to the so called æinsignificant elementsÆ connecting this metallurgical equipment, such as chutes, pipes or other conveying systems, and particularly to the sufficient protection of their wearing surfaces. The result can be an unplanned and expensive outage caused by the wear related failure of such components. This paper will discuss:the theory of wear and the multiple factors of material and design that contribute to a reduction in wear; and the combinations of modern wear resistant materials available to todayÆs engineer and how, by intelligent selection and correct application, plant availability can be optimised. Examples outlining how these principles have been applied in South Africa showing some improvements leading to increased plant availability.

Jan 1, 2002

A case-study is presented of the tailings dam of Nairne Pyrites Pty. Ltd., at Brukunga, South Australia. The methods of-construction and operation of the dam are outlined over the whole working life of the mine. Procedures of soil mechanics used to estimate the stability 'of the face of the dam are described, and seepage problems are dis- cussed. It is concluded that the dam is basically stable, and enabled Nairne Pyrites Pty. Ltd. to dispose of tailings economically, although more attention to seepage control may have been ad- vantageous. Suggestions are made on the construction and operation of tailings dams elsewhere.

Jan 1, 1975

By J Chen

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled stopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench stope fill mass is described and a technique for reducing the potential for bulkhead failures in bench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also described.

Jan 1, 1998

A standard practice of auditing mill designs has developed in the mining industry. The purported aim of this task is to ensure that the mill being offered conforms to the design specification, thus reducing the purchaserÆs risk. However, careful examination of the auditing methods used in the past shows that this is not the case. In some cases, what auditors have been providing is effectively a quality assurance check of the input data, not a full independent audit of the vendorÆs design. It will be shown that these past auditing methods have contributed to the stagnation of mill specification development. This lack of specification improvement combined with the current trend towards increased allowable fatigue stress ranges can result in an increase in risk for the purchaser.

Jan 1, 2002

By T Kitajima, T Kawaguchi, T Nakamura

Carbothermic reduction of iron oxide is an attractive mechanism to produce metallic iron, since it can directly utilise coal as both reductant and fuel. To improve energy efficiency and productivity of the metallic iron production based on this mechanism, the combustion bed process packed with the composites of iron oxide and coal powder was experimentally evaluated. The process has a potential of high heat efficiency since it can automatically utilise the heat of reduced materials as that necessary to the subsequent reduction of the composite by a large heat exchange rate between the packed particles and gas flowed across the bed. However, it is hard to perfectly prevent the reoxidation of formed metallic iron in the bed. The present paper reports the effect of coal content, pellet size and so forth on the reduction/metallisation degrees of the samples after the reduction experiment. It also discusses the effect of pretreatment of the composite pellets using CaO bearing materials to suppress the reoxidation of formed metallic iron in the bed.

Jan 1, 2000

By Firmin K

The Mt. Tom Price orebody of Hamersley Iron Pty. Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the orebody, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control'of products based on selective mining is the production of advance data, on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades Are determined from assay of samples taken from blasthole cuttings.

Jan 1, 1980

By D Matthews

With a brownfield project comes control integration challenges. The Khumani Iron Ore Mine’s second phase expansion posed a number of challenges as there was substantial brownfields work conducted. The fi rst phase was the compilation of the modifi ed process functional specifications for the project. The second phase was an audit on all of the operational sequences; this included a comparison between the SCADA sequences, sequential starts analysed from the historian data (with the potential for improvements made by the plant operators in manual start-ups) and what was proposed in the process functional specification. Differences, inclusions and missing equipment were highlighted. The third phase was the comparison of interlocking and control in the PLC with the updated process functional specification; this was done during the coding process. Running parallel to the three phases was the SCADA integration; tie-ins to the existing SCADA were conducted on maintenance days and shutdowns, in many instances with ‘dummy’ equipment to get the operational staff accustomed to the new interface. This paper details each of the phases, the success of this methodology as well as the pitfalls experienced.

Jul 11, 2011

By D Nourry

Optimising the blast is a major issue in the blasting business. It generally means acting on the blasting pattern (drilling, charging, detonating) in order to get a given æresultÆ. This result may either be related to economic reasons, such as the fragmentation influencing productivity, or technical reasons, for example vibrations and projections. Within the frame of the EEC funded Brite-Euram project entitled æBlast-ControlÆ, involving academic research and applied expertise, a general methodology was developed to approach such a problem and currently applied to the industrial partners of the project and final end-users of the generated results. These partners are the limestone ALZO quarry of the CALCINOR group in the north of Spain and the dolomite DMD (Dolomies-de-Marche-les-Dames) quarry of the LHOIST group in the east of Belgium. A first part of the project, over 18 months, was dedicated to establishing a clear relationship between productivity of operations from drilling to primary crushing and the fragmentation resulting from the blast. Extensive monitoring of blasting, production performance and fragmentation data was carried out and automatically collected into a database on both quarries. As expected, it appeared that excessive amounts of fines or boulders were substantially reducing productivity and thus profitability of the operation. Furthermore, an æoptimalÆ fragmentation was assessed for the quarries to run at the best (high throughput, low cost). The second and last part, for the remaining 18 months, was then dedicated to adapting the blasting practice in order to orientate the fragmentation towards a æbetterÆ one. A very common problem normally addressed by any consultant. Nevertheless, the target was not limited to solving the problem for these two quarries, but also to develop a generic method to address this blasting adaptation process and to implement it into a computerised tool. At this stage, it is then obvious that portability of the method and the system are major qualities to be looked for. This paper is aimed to present how this method was developed, how the system was implemented and how it was finally used.

Jan 1, 2001

By K Orth

The volcanic successions that host massive sulphide deposits are diverse in composition, facies types and facies relationships. They also show a variety of spatial and temporal relationships to mineralisation. In many examples, such as the Koongie Park Formation in Western Australia, the host succession includes more or less conformable syn-volcanic sills with peperitic contacts. Such sills can be an important source of heat for fluid circulation, influencing patterns of hydrothermal alteration and the location of co-eval and later mineralisation. The impact of syn-volcanic sills on the host succession depends in part on the initial porosity and permeability of the enclosing facies. The special properties of glassy pumice û being highly porous, permeable, and reactive û allow pumice-rich facies to preferentially focus hydrothermal fluid flow. However, the same properties promote early alteration and porosity reduction. Hence, the diagenetic and compaction history of pumiceous facies strongly influences their potential to host massive sulphide mineralisation. In contrast to pumice, dense glass has relatively low porosity, at least initially, and does not compact. Non-vesicular glass is a major component of submarine lavas, syn-volcanic intrusions and some volcaniclastic facies. However, especially in submarine settings, dense glass is commonly intensely perlitically fractured soon after eruption. The fractures greatly increase the porosity and permeability, locally accelerating diagenetic and hydrothermal alteration. In addition to false pyroclastic textures, altered perlite may exhibit false porphyritic textures. Silica- or feldspar-altered perlite kernels surrounded by intensely altered phyllosilicate domains can resemble phenocrysts in a fine grained groundmass.

Jan 1, 1999

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022

By C A. Thomas, J C. Eardley, G V. Franks

As valuable minerals are more disseminated, there is a need for low-grade ores to be finely ground to liberate these valuable minerals. However, this has a negative impact on ultrafine mineral recovery as conventional separations processes such as gravity separation are no longer effective. Instead, fine particles can be recovered by froth flotation. Various novel reagents have been introduced along with development in flotation cell designs such as Jameson cell and column cells to improve performance and recovery of ultrafine valuables. This study, on the other hand, aims to recover the fines using a combination of commercially available reagents to selectively flocculate the valuables, so they are large enough to be recovered via conventional froth flotation cells. This technique if successful can be implemented in many existing industries that continue to use mechanical flotation cells that require particle sizes to be 50–150 μm for effective recovery (Ralston, 1992; Batterham and Moodie, 2005). Selective flocculation is not widely implemented in industries mainly due to the inability to float the aggregates ones they are formed and gangue entrapment within the aggregates which consequently affects the grade of concentrate recovered (Forbes, 2011). The major goal is to aggregate the minerals and float the aggregates unlike the more common industrial technique such as reverse flotation of hematite, where the aggregates itself is not recovered via flotation.

Aug 24, 2022

By Thuli AJ

Copper concentrate from Bougainville's copper mine located on the west slope of the Crown Prince Range on Bougainville island, is pumped 27 km to the filter and drying plant at Anewa Bay for preparation and storage prior to shipment to overseas customers. Prior to shipment the thickened concentrate slurry is passed through a test loop to check that its consistency and pH are acceptable for transportation through the main pipe line. The Bougainville pipe line is unique since it is the world's first copper concentrate system. where slurry is pumped an appreciable distance against a high head,

Jan 1, 1975

The bulk and surface chemistry of metal ion hydrolysis and precipitation and the redox chemistry of metal ions, sulphur, and other species is central to an under- standing of flotation. The paper contains a review of general hydrolysis-redox chemistry appropriate to the flotation process, and a model of natural and collector-induced flotation of sulphides is constructed. The practical application of the model to real flotation systems is then explored with a view to better under- standing of the chemistry of selectivity and grade control.

Jan 1, 1984

By B Delaney

For worker safety, mining companies are required to stop production and inspect hoist ropes. Visual inspection is generally done daily and EM inspection occurs every three to four months. During visual inspection, rope speed is generally reduced so an inspector can look for problems. In EM testing the LMA and LF traces are printed on a paper strip chart and a skilled operator interprets these traces. Mining companies only find large defects during visual inspection and are sometimes concerned about the content of EM trace information. This paper will present research outcomes that show how muck can be hoisted while performing a complete visual rope inspection at full speed. Other research results will show that digital signal processing can increase the amount of information available to the EM rope inspector. The research was funded by Inco, C-CORE, three AMIRA International sponsors and six sponsors from the Canadian Deep Mining Research Consortium (DMRC). The research will be commercialised in 2005.

Jan 1, 2005

By Cox N

Fragmentation control is perhaps the most critical aspect of quarrying operations, potentially impacting on the costs of all down stream processes, and sometimes even on the economic viability of an operation. The focal points of studies to control fragmentation are generally the pattern of blastholes, the accuracy of drilling, and the most appropriate powder factor. Recent studies suggest that the performance, and consistency of performance, of explosive detonation in the blastholes may also be a significant factor impacting on blast performance in hard rock quarries. This paper presents the results of studies of bulk emulsion and watergel explosive performance, using blasthole velocity of detonation measurements, and its impact on fragmentation. Field studies show a strong correlation between blasthole VoD and blast fragmentation. Another aspect of explosive performance impacting on ease of excavation of blasted rock is muckpile displacement, from which estimates of effective heave energy have been made for different bulk slurry (emulsion and watergel) products.

Jan 1, 1995

By McKenzie C. K

During a programme of explosive performance evaluation at Hamersley Iron, Mount Tom Price Mining Operations, the relative performances of a range of heavy ANFO explosives were compared during normal production blasting operations. In addition, a number of heavily instrumented single hole blasting trials were conducted with each product type. The blasts were monitored in terms of blasthole velocity of detonation (VOD), measured using multi-point plasma conductivity probes with up to 16 measurements per blasthole. Up to 16 blastholes were monitored in each production blast. The results of measurements show a marked difference in performance of all heavy ANFO products between single blastholes and full production blasts, indicating a significant degree of interaction between blastholes in production blasting. The interaction is shown to result in a loss of detonation pressure of explosive, and considered to lead to a loss of fragmentation. The degree of interaction is seen to increase with increasing emulsion content in the products, and is more pronounced in some explosive types than others. The paper presents the methods of measurement and analysis, and the results of monitoring, together with implications on blast design and application of heavy ANFO products.

Jan 1, 1990

Most of the gold reef mined today in South Africa is approximately 1 m in width with slopes about 30 m long. To prevent production interruptions it is essential that the stopes should not be blasted in sections. The shortage of experienced labour and arduous working conditions at the face dictate the need for simple blasting techniques.Hence, a pyrotechnic blasting system of sequential firing is in use at present, although research work to improve this technique is in progress.

Jan 1, 1985