Search Documents

By J Kleynhans, D Vermeulen, V Cogho

A number of rehabilitated open cast coalmines in SA are already decanting. The paper focuses on the situation at one of these mines where the following information exist: monthly decant rates and rainfall; sulfate concentrations of the decanting water; water level measurements inside the mine prior to decanting; ABA analyses; information about the rehabilitation (drainage slope, vegetation, soil used). A 2D-model was constructed for the mine and calibrated against six years of flow data. About 85 per cent of the decant outflow rate comes from direct recharge on top of the rehabilitated mine while the other 15 per cent is derived from lateral groundwater inflows. The estimated recharge value was 17 per cent of the rainfall. Measured sulfate values showed that the sulfate generation rate for the mine was in the order of 7 kg/ha/d. Conclusions from the study are:most of the water decanting from rehabilitated open cast coal mines is derived from recharge via rainfall; given a specific sulfate generation rate, then: the lower the recharge the less the decant rate but the higher the sulfate concentration of the decanting water and vice versa; future prediction of the decant rate must be stochastic according to expected percentile monthly rainfall values; and as a first assessment of the predicted sulfate concentration of decant water from rehabilitated open case mines, the 7 kg/ha/d sulfate generation rate can be used.

Jan 1, 2003

By E Jamieson

For a number of years, Alcoa World Alumina Australia (Alcoa) has been investigating opportunities to produce economically viable products from bauxite residues. Three of these potential products are described here, being Red Sand, ALKALOAM« and REDLIMETM.Red Sand has a nominal particle size of +100 micron and is physically little different to crushed bauxite from which it is derived. In AlcoaÆs Western Australian refineries, Red Sand constitutes up to half of the residue going to impoundment areas. Initial testing indicates that this sand could be processed to provide an acceptable general landfill material, a construction back fill or a material suitable for road base construction. ALKALOAM« is the fine-grained residue often referred to as red mud. A great deal of work has been done to show the benefits of adding this material to sandy soils, which are common in coastal regions of WA. ALKALOAM« has properties that can elevate the pH of the acidic soils and also retain phosphorous, reducing overall fertiliser use and protecting sensitive waterways. REDLIMETM is a by-product of the refining process. This material has a high acid neutralising value. REDLIMETM could be more effective at pH control than most available products because of the fine particle size and sodium carbonate that remains with the product.

Jan 1, 2004

By S Prakash, M Danish, D Kumar

The green energy transition is speculated to cause an increase in the demand for raw materials while recycling rates are improving; discoveries are required to maintain supply. Geological remote sensing offers a cost-effective way of exploring mineral resources. While satellite and airborne imaging are routinely used for exploration targeting, a gap remains at the outcrop scale. Hyperspectral imaging (HSI) is advantageous for large-scale regional mapping, typically performed from satellite or airborne platforms. Accurately mapping geological lithologies remains challenging in inaccessible areas, such as rough terrain or mine sites. Proximal sensing techniques can boost geological activities’ reliability, safety, and efficiency in exploration or during mining activities. It also generates objective, reproducible results and valuable raw data that can be archived, further processed, and re-interpreted. Ground-based hyperspectral imaging of outcrops has steadily increased during the last decade due to sensor development and better processing routines. There is often a big technology gap related to mineral mapping, integration of images and spectra (reduction in manual identification of minerals and types) and hyperspectral data visualisation through remote sensing. TEXMiN Foundation, in collaboration with its industry partner Dassault Systemes Foundation, carried out the project, ‘Developing Hyperspectral Image Processing and Analysis, build a rich library of Hyperspectral images of a vast range of minerals from India which will help in increasing prediction accuracy of mineral deposit for mining exploration’.

Sep 1, 2024

By Hein K. A A

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By S Vearncombe

SpaDiSÖ is a revolutionary approach to the spatial analysis of point data using geometry to analyse geometry! SpaDiSÖ uses each and every spatial relationship and is not dependent on mathematical models. For n points there are n2 û n spatial relationships and, because of the square function, the method yields interpretable results for both small and large data sets. SpaDiSÖ is an alternative to variography for directional studies. At the regional scale, the analysis can assess distribution patterns of mineralisation and potential controlling structures. At the deposit scale, the characteristics of zones of mineralisation such as direction, spacing, high-grade ore direction and grade distribution can all be deduced.

Jan 1, 2000

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

Silver-lead ores are widely distributed through- out the Mount Lofty and Flinders Ranges, but none of the deposits is large. Historically the Glen Osmond Mines are the most significant as the site of the first metalliferous mining in Australia, but Talisker was one of the three largest producers of silver-lead in a state whose mining history is dom- inated by copper. The mine is located in a magnificent natural setting on Talisker Conservation Park, near Cape Jervis, southwest of Adelaide (Figure 1). It is exempt from the operations of the Mining Act and listed on the Register of State Heritage Items. The mine and associated township of Silverton were dominated by Cornish influences during the period of principal activity between 1862 and 1872. Silverton, located on a ridge overlooking the mine, grew to a population of about 300 at its peak in 1870 and the area was very much another 'little Cornwall'.

Jan 1, 1987

By R Trueman

An improved ability to predict dilution for narrow vein deposits enables more accurate economic comparisons between mechanised longhole stoping and other narrow vein mining methods, as well as reducing uncertainty surrounding dilution estimates for deposits at the prefeasibility/ feasibility stage. This paper proposes narrow vein dilution prediction and minimisation strategies for both greenfield sites and operating mines, respectively. The narrow vein dilution method (NVD method) is a tool for more accurately predicting longhole narrow vein dilution. The method is based on a new concept called benchmark stoping width. Benchmark stoping width is based on probabilistic analysis of overbreak distributions from a typical longhole narrow vein mine. The premise for the NVD method is that dilution associated with longhole stoping can be predicted using the benchmark stoping width. In addition to dilution prediction, the NVD method also includes strategies for narrow vein dilution minimisation generally, including; filling, cablebolting, stress relaxation, extraction sequencing and blast overbreak.

Jan 1, 2008

By A Annor, L J. Chen

The production of paste backfill has typically been accomplished through the adaptation of existing technology. Thickeners and disc filters have several drawbacks when applied to production of tailings paste backfill. Personnel at CANMETÆs backfill research laboratory in Sudbury, Ontario, Canada have been carrying out research into and development of methods to produce paste backfill using total mill tailings since 1991. Using a silo for production of paste is not a new concept but has been refined to a marketable level. This technology is based on a fluidization principle that assists in settling the tailings to an homogenous state in a silo. Other developments include patented de-watering technology for use in the silo to speed the settling of the solids to a suitable solids content, optimisation of silo geometry, and instrumentation related to paste backfill production and transportation. The advantages to fluidisation technology are in reduced capital cost, reduced operating costs and in the environmental benefits of using full plant tailings over classified tailings or alluvial aggregates. Another major advantage is in the ability of this technology to be retrofitted to existing hydraulic backfill plants to further reduce capital cost. This paper details the development of the new technology as well as the associated cost savings over other technologies. It will also look at the research and development of unique components that make this technology work.

Jan 1, 1998

By Seedsman R. W

Good roads are essential in moving men and materials to and from the underground workplace. Coffey Partners International Pty Ltd (Coffey) has recently completed a underground coal industry funded project on underground mine road construction and maintenance. This paper discusses practical approaches to construction and maintenance of underground mine roads using transferrable civil technologies and innovative techniques. Mine pavements are generally low-cost (relative to civil roads), constructed to varying standards using locally available materials to best meet the mobility needs of the mine. Performance of pavements is thus largely dependent on the environmental conditions, quality of the available road making materials, maintenance policies and available resources. The paper will detail `what causes bad roads?' in various underground environments, available management strategies, construction and water control techniques, road maintenance and vehicle considerations.

Jan 1, 1995

By R Mackay, J Brereton

On 30 June 2020, the Mine Land Rehabilitation Authority (the Authority) superseded the Latrobe Valley Mine Rehabilitation Commissioner as the independent overseer of Victoria’s declared mine rehabilitation. Currently, only the Latrobe Valley’s three brown coalmines are declared, with each mine at a different stage of rehabilitation and closure planning: Hazelwood ceased mining in 2017, Yallourn is scheduled to end mining in 2028 and Loy Yang in 2035. The three declared mines are very large, close together (Figure 1) and present significant environmental risks that must be mitigated during rehabilitation and post closure. In addition to fire risks, the brown coalmines are inherently unstable and require continuous monitoring and management of ground movements and groundwater pressures. Since 2007 several damaging events have occurred, highlighting the difficulties of achieving long-term stability, even with good landform design and rigorous ground control management plans

Aug 2, 2023

By R S. Suglo, G-K Er

Mineral processing is an essential component of a mine production chain and it accounts for significant proportion of the production cost. Over the past decade, significant research progress has been made in processing plant efficiency using theoretical, experimental and simulation modelling techniques. However, these studies are limited to process plant system as stand-alone units with no interactions with the mining units. In order to maximise the total mining system efficiency and more accurately simulate the system, the processing plant must be modelled as part of an integrated mining system. This becomes increasingly important in continuous surface mining systems, with limited ore processing capacity. In addition, plant efficiency is roughly estimated with known parameters or with simplistic statistical data, without regards to the stochastic processes governing these parameters, such as processing plant feed introduction. In this paper, a comprehensive model of the ore processing plant system is given and the object-oriented design (OOD) of the system is briefly introduced. The joint operation of ore processing plant system and haulage system is analysed. Numerical modelling is used to analyse the ore processing plant system under different conditions. Analysis of the results show that the optimum plant capacity is 0.7 tons/sec (2520 tons/hour). The results also show that the plant system resources cannot be fully utilised because the production rate is always less than the plant capacity. When plant capacity reaches an optimum value 0.7 tons/sec, the production rate is about 0.64 tons/sec. The underlying stochastic processes associated with plant and mine capacities cause this variability. In order to reduce this variability, there is the need to tightly set tolerances for the function variables.

Jan 1, 2003

By D A. Shushkov

Analcime-bearing rocks are one of the varieties of raw zeolite material, although the characteristics of analcime are not as good as other kinds of zeolites such as clinoptilolite or mordenite. However, some fields of application of analcime-bearing rock have been found, eg a method of water purification has been developed and patented. Analcime-bearing rocks are rather widespread in the Timan region of the Komi Republic of the Russian Federation. They are represented by Upper Permian siltstones and mudstones. The analcime-bearing rocks have the following mineral composition (per cent): clay minerals (50 - 70 per cent), quartz (ten to 30 per cent), analcime (one to 30 per cent), feldspars (two to ten per cent), carbonates (two to five per cent) and pyroclastic material. Analcime aggregates encrust cavities and infill microfissures in rock. Both microcrystalline (crystals <0.01 mm in size) and medium-crystalline (~0.5 mm) aggregates are observed. The mechanical, gravitational, magnetic, sorption and ion-exchange properties of analcime-bearing rocks have been studied. They are characterised by a high index of grindability and a low index of abradability and crush resistance, low values of the benzol-based pore volume and toluene-based specific surface area, and a medium porosity value. The magnesium based ion-exchange capacity (IEC) ranges from 28.7 to 196 mg+equiv/100 g. Analcime-bearing rocks of the Timan region are characterised by low beneficiation potential. Preliminary ultrasonic treatment of the analcime- bearing rocks is efficient for the destruction of intergrowths along their boundaries and production of free analcime aggregates. The proposed beneficiation procedure yields 95 per cent analcime concentrate. In the Komi Republic, analcime-bearing rocks are utilised in agriculture. They are also used for domestic needs (eg as biotoilets for domestic animals) and the solution of ecological problems (regeneration of soil polluted by oil). We have completed experiments on the purification of potable and industrial water using analcime-bearing rock subjected to thermal treatment. The experiments demonstrated that it was possible to decrease water colouration by 20 per cent, turbidity by 79 per cent, permanganate oxidation by 30 per cent and total iron content by 70 per cent.

Jan 1, 2008

By E Yll÷, O HyvSrinen

Outokumpu has developed a new chloride leach process, called HydroCopper«, to treat copper concentrates. Chalcopyrite is quite refractory in leaching and in sulfate milieu an autoclave of high temperature and pressure is required. However, in the HydroCopper«-process copper sulfides can effectively be leached in atmospheric pressure using strong, aggressive chloride solution and copper (II) ions as oxidant. Copper is precipitated from the purified pregnant leach solution as copper (I) oxide, which is filtered and reduced by hydrogen gas to metallic copper powder, which is melted and cast into copper product. Sodium chloride formed in precipitation is decomposed in a chlor-alkali electrolyser, the products of which are circulated back to the process: sodium hydroxide to copper (I) oxide precipitation, chlorine gas to leaching and hydrogen gas to the reduction of copper (I) oxide. During 2003 - 2004 the performance of the HydroCopper«-process was confirmed in a demonstration plant processing one tonne of copper per day. It has been found to be applicable for different kinds of concentrates and can also tolerate a wide range of impurities. A significant advantage of the process is that gold can be leached as a chloro-complex and recovered with active carbon. HydroCopper« can economically recover copper from concentrates and process to a cast copper product. The best utilisation of the process is in most cases achieved when the plant is situated at the mine site. Higher recoveries are attained by the optimisation of the whole operation chain from the mine and the concentrator to the HydroCopper« plant.

Jan 1, 2005

By T Jones, K Karunaratna

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is located on the eastern boundary of the Kalgoorlie-Boulder City and is mining an area traditionally known as the Golden Mile. The pit area has been continuously worked since 1893, predominantly by underground mining methods and more recently through open cut mining. There are over 2000 km of old mine headings and numerous stopes under the open pit area. KCGM has interpreted and digitised the underground mine plans and stope sections into a common database. A 2D-model software package, called Pits, was developed in-house and allows old workings to be displayed at any bench level; this is integrated with 3D Vulcan modelling software, which allows triangulated surfaces to be displayed. Almost every mining activity is affected by underground workings. The effective management of the interaction between current mining and the underground workings is very important for safety and production. A specific ævoidÆ management department has been formed and its broad objective is to minimise the impact of underground workings upon production while maximising safety. Special criteria and procedures have been developed and implemented to keep personnel and machinery from being exposed to unsafe ground. It is of primary importance to accurately define the location and outline of underground workings in advance. Probe drilling has been used as the key tool for that purpose. Various geophysical methods have also been trialled on site to detect underground workings; these are discussed in some detail. This paper discusses ævoidÆ management issues such as data integration, void detection and flagging. The impact of underground workings on mine planing, production and slope stability is also discussed.

Jan 1, 2003

By B OÆNeil

The Trent-Severn Waterway is a 386 km long navigation route through central Ontario between Lake Ontario and Georgian Bay, and is operated by the Parks Canada Agency. Its primary focus is to pass recreational boats through a system of 44 locks. The Big Chute Marine Railway (BCMR) is one site in the system that provides transportation for boats. The BCMR carriage is used to transport boats and their passengers on the inclined railway a distance of 230 m over a natural barrier from one body of water to another, with an elevation difference of 18 m. The unique feature of the haulage system used in this application is the variable angle of the incline from about 20 per cent rise changing to horizontal and followed by 20 per cent decline. In such conditions, unlike as in standard incline haulage, special configuration of hoists and drives is required. On the uphill part of the track, there is a need to have a motoring mode, on the downhill part a regenerating mode and on the horizontal part a combination of motoring and regeneration is required. The original system was built in 1978 and employed four 100 hp dc drive mine hoists to haul the 100 tonne conveyance loaded with 90 tonnes of boats. Due to failures and operational problems with the original system, in 1999 Parks Canada awarded a turnkey contract to ABB for a new, modern system of four single drum hoists. The new system was put into operation in 2000, only six months after receiving the order. The hoists are controlled by digital drives and a digital control system. Due to dramatic changes in the load conditions for individual hoists involved, the new system features many interesting solutions like changing drive modes from speed to torque control and a multiple, regulated braking system. It is a unique hoisting system, which could be also used in mining applications.

Jan 1, 2005

By N Udugampola, d A. Seneviratne, X Ai, B Li

With the evolution of mining technology, wireless mesh networks using low-power, long-range technologies such as LoRa are increasingly utilised in underground mining operations. Efficient deployment of wireless nodes in such mesh networks necessitates understanding radio wave propagation behaviour in underground mines. While existing propagation models either remain theoretical or apply only to basic geometric shapes, we propose a practical approach to analyse radio wave propagation behaviour in underground mines using ray tracing simulations with reconstructed 3D models of targeted environments. Our method validated using a set of corridors as a substitute for underground mine environments, involves constructing a 3D model using SolidWorks from LiDAR scans of the environment and performing wireless transmission simulations using the MATLAB ray tracing toolkit. Our simulation model is also fine-tuned by calibrating the raytracing parameters based on real-world LoRa transmission experiments in the actual environment corresponding to the 3D model. This method offers a practical solution for optimising wireless node placement in underground mines, facilitating efficient network deployment while reducing the need for extensive physical testing of radio wave transmissions.

Sep 1, 2024

By Saint-Smith J. C

The anode, tank house and wire bar plant and operations are described with particular reference to those features of design and methods which are characteristic of this refinery at its inception.Reference is also made to auxiliary equipment, transport and materials handling facilities.The work of commissioning the plant late in 1959 is discussed and comment is made on the organisation of construction and origin of the equipment.LOCATION OF PLANTThe site chosen for the copper refinery is on level ground adjacent to the junction of the Mount Isa and the main north-south railway lines at Stuart near Townsville, Queensland. Blister for refining is received by rail from Mount Isa. Refined products are taken 10 miles by road to Townsville Harbour for shipment to other Australian ports or overseas, or despatched by rail direct from the plant.Adequate room for expansion was provided to cover copper refining and any associated industry. The layout of future extensions was planned and space reserved for them before detailing the original units of the main refinery.The initial plant also provides convenient storage facilities and is laid out to derive the greatest benefit from prevailing northerly breezes during the humid tropical summer.As far as possible, the working areas are located so that the prevailing winds cool them as they traverse the buildings.These factors are of very great importance since this is believed to be the only copper refinery in the tropics operating with all white labour and in any case the Company set out to provide the best possible conditions for its operating personnel.

Jan 1, 1961

By C Deacon

It is common practice to include microspheres or similar density reducing agents in inherently insensitive water-based commercial explosives to achieve detonative sensitivity in the absence of chemical sensitisation. It has recently become possible to similarly include microspheres in LDAN (low density ammonium nitrate). Further to previous studies and publications to determine the benefits resulting from the use of microsphere enhanced LDAN technology in blasting, additional advantages are described in this document. These include range tests at independent testing facilities (Universal Tech Corporation û USA) which reflect results observed in the field, and support theoretical assumptions made when the products were introduced. Additionally, on-site studies in opencast pits using Heavy-ANFO blends incorporating modified LDAN, show that monetary savings can be realised through significant advantages gained in plant throughput and explosives use.

Jan 1, 1999

Although technology and circumstances are in a constant state of change, the principles of managing the human element remain constant. The isolated mining community continues to form the backbone of the minerals industry but the nature of the isolation, along with the economic and political environment of the industry, is changing. These changes require new inputs by management to the workforce. Management must determine an effective working relationship with unions on its mine site and concurrently contribute to the build- up of the expertise of the individual worker through training and communication. It must also retain a proper balance, by way of human contribution, in cost and information reporting and in other areas amenable to computerisation. These comprise the aids to management necessary to achieve the desired operating efficiency and profitability.

Jan 1, 1980