Search Documents

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Cumming-Potvin

Incidents that trap miners in underground mines have serious consequences for the miners and the mine operators involved. It is of utmost importance that mine operators utilise all available tools when trying to locate and rescue trapped miners. From testing conducted at underground hard rock mines, Cumming-Potvin et al (2013) found that pre-existing microseismic monitoring systems, which are routinely used for seismic risk management, have the potential to be used for detecting and locating trapped miners.This paper reflects on the Anzac Day seismic event that trapped two miners at Tasmania Mine, Beaconsfield, on 25 April 2006. The Anzac Day event occurred at 2123 on a Tuesday evening. Rescuers were unable to confirm that the trapped miners had survived until 1930 on Sunday evening. It is not possible to speculate on how the rescue operation may have been different had the technology to use the microseismic monitoring system for the purpose of detecting the trapped miners been available. However, it almost certainly would have been different. The recent research project has demonstrated that knowing the fate of the Beaconsfield miners might have been achievable up to 100 hours earlier than was the case in 2006. That knowledge would have been invaluable to the rescue effort.By examining the seismic array at the Tasmania Mine, the reliability of detection over the working levels of the mine could be quantified. Had the methodology been available, adding six additional sensors (at a cost of $40 000), would have been sufficient to increase the likelihood of detection to greater than 90 per cent in the working levels of the mine. This was true both at the time of closure of the mine in 2012, and just prior to the Anzac day event.CITATION:Cumming-Potvin, D and Hills, P B, 2014. Use of a pre-existing microseismic monitoring system to detect trapped miners (with reflections on Beaconsfield 2006), in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

By J Lombardi

OZ Minerals' Prominent Hill copper-gold concentrator is located 130 kilometres south east of the town of Coober Pedy in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 9.6Mtpa ore throughput capacity. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell heading up the three stage conventional cell cleaner circuit. In total there are four level controllers in the rougher train and ten level controllers in the cleaning circuit for eighteen cells.Generic proportional – integral and derivative (PID) control used on the level controllers alone propagated any disturbances downstream in the circuit that were generated from the grinding circuit, hoppers, between cells and interconnected banks of cells, having a negative impact on plant performance. To better control such disturbances, FloatStar level stabiliser was selected for installation on the flotation circuit to account for the interaction between the cells. Multivariable control was also installed on the five concentrate hoppers to maintain consistent feed to the cells and to the IsaMill. An additional area identified for optimisation in the flotation circuit was the mass pull rate from the rougher cells. FloatStar flow optimiser was selected to be installed subsequent to the FloatStar level stabiliser. This allowed for a unified, consistent and optimal approach to running the rougher circuit. This paper describes the improvement in the stabilisation of the circuit achieved by the FloatStar level stabiliser by using the interaction matrix between cell level controllers and the results and benefits of implementing the FloatStar flow optimiser on the rougher train.

Aug 8, 2011

By Creasey JW, Rixon KL

Underground mining in the Bowen Seam has shown that the majority of outbursts have co- incided with faults, igneous dykes and sills, stone roof rolls or some combination of these. The coal measures are deformed principally by N- S trending, easterly dipping thrusts presumed to he associated with the major, reverse Collins- ville Fault. The old Collinsville State Mine records suggest that thrusts and strike-slip faults have been common sites of outbursts. In contrast, normal faults have not been outburst- prone. Detailed geological mapping in Bowen No. 2 Colliery 53 east and west panels has been carried out in the hanging wall of a thrust zone of 6.1 m throw. The associated sheared coal has been defined and several fracture sets delin- eated. Sheared coal can be observed up to 170 m from this thrust zone, but this is dependent on the vitrinite content of the upper seam section worked. Fvidence indicates that outbursts have crnrroJ only in extremely sheared coal. Curious spherical- to cylindrical-shaped c,,.31 ohjects ("apples" and "rods") are related to the deformation in the vicinity of the thrust zone. The frequency of rods rises from 0 at 31)0 m, to I per metre at 150 m, and to 2.5-8.5 per metro at 10 m from the -

Jan 1, 1980

How do you initiate closure planning for a mine site that is on the doorstep of a major community without generating the extremes of panic or complacency? That is the question that is faced by Australia's largest gold mine, the Kalgoorlie Consolidated Gold Mines (KCGM) Super Pit in Kalgoorlie-Boulder. KCGM's Community Relations Manager, Danielle van Kampen, will reveal the lengthy closure planning process that is in train to alert yet not alarm the community about the future of the Super Pit and to generate discussion on issues of importance. What will happen to the 'big hole' that generates both mining and tourism dollars for the City of Kalgoorlie-Boulder as its anticipated closure date of 2021 comes closer? How do you communicate a constantly evolving closure date? Although the process may generate more questions than answers, the project will be discussed at length and with the added benefit of independent community recent research in the form of the public 2009 Closure Consultation and the KCGM 2010 Social Impact Assessment. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

Visual computing opens the design process to a wider audience and allows rapid communication of mine plans to all stakeholders. The integration of software and hardware technologies that take advantage of a graphical environment will continue to improve both long-term and short-term mine design (Figure 1). A good design must be adaptive to respond to decision changes as the mine develops and more information becomes available. The constraints on mine design predicate careful analysis in order to operate the mine as efficiently and safely as possible.Continuous improvement in mining is assured by developing innovative technologies that target mine survey, drill and blast, modelling, short-term design and pit and stope optimisers. The design life of a mine has to be sufficiently long to ensure the mine is commercially successful, justifying the high start-up capital costs. Being able to execute a plan so that it honours the design realises the rewards of computerised mine planning and the long-term investment in data acquisition.

Sep 26, 2011

By V O’Brien

The suitability of magnetic surveys flown at low altitudes to identify buried heavy mineral (HM) strands has long been accepted. This is despite the low intensity magnetic response often obtained from such strands. The fundamentals of the magnetic survey method dictate that the closer the instrument is to the source the stronger the response. As such the optimal elevation for the magnetometer is at or near the surface. Iluka sought to use a ground based magnetometer to aid in the exploration target generation process and allow accurate targeting of exploration drill holes. Following the initial trial Iluka recognised the potential additional application of data obtained by a ground based magnetometer over known strand deposits. The detail of the ground magnetic images can confirm the assumed strand continuity between cross-sections of close spaced drilling and can aid in the definition of the geometry of different generations of mineralisation. The ability to confidently determine that the deposit has not been truncated by post emplacement erosion of the mineralised deposit may enable reductions in drilling requirements as well as assisting mine planning activities. Iluka intends to investigate advanced modelling of the magnetic data to determine the level of strand geometry and HM content resolution that can be achieved from the ground magnetic survey data and its potential application in the mining grade control process.It is anticipated that the surveying of Iluka’s known resource deposits will provide the ability to correlate the magnetic response from new exploration targets with those from known deposits for a given depth, HM grade and mineralogy suite.

Oct 5, 2011

By P Card

Some project managers accept unsatisfactory economic evaluation modelling because they are unaware of what constitutes good practice. They tend to leave it to the evaluation specialist or others to decide. The AusIMM has published on its website a draft set of guidelines for technical economic evaluation which will allow these project managers to take control and demand worldÆs best practices.The style of the guidelines is described and the source of a worked spreadsheet example in Excel is given.Economic evaluation in project management is described. A simple test for the acceptance or rejection of evaluation work is offered. The nature of modelling and evaluation in each of the three study phases of concept, prefeasibility and final feasibility are described. Suggestions on the selection of specialists for each phase are given. The three levels of evaluation thinking are described, namely, modelling, valuation and evaluation. Finally the meaning of æfinancial analysisÆ is explained.The conclusion is that æthe role of an economic evaluation specialist is to create models and evaluations for the whole project team to readily understand and use: it is not to create models for his/her own useÆ.CITATION:Card, P, 2012. What project managers must demand from an economic evaluation!, in Proceedings Project Evaluation 2012 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By B W. Atkinson, J Docherty

An Australian Working Group has been compiling a guide for operators to use in order to improve the efficacy of their routine and non-routine sampling tasks within their coal preparation process. The guide focuses on unit operations within the process, and not conveyor belts or transfer stations that are adequately covered by the existing Standard ISO 13909.Representative sampling of unit operations is generally an after-thought following plant construction, whether that be a result of oversight, or more commonly, capital cost minimisation during initial construction. Minimising capital cost by avoiding adequate sampling systems is generally a poor decision, since the result is a process that cannot be adequately measured, meaning that it cannot be adequately managed and optimised.The use of the term ‘guide’ rather than ‘standard’ is intentional. Practical means of sampling unit operations within existing plants generally relies on a compromise between sample representativity (minimisation of bias) and sampling feasibility. The guide does not endorse poor sampling practice, but instead offers practical guidance to overcome, to the extent reasonably possible, real-life limitations.When it comes to sampling any particular process, it is almost always necessary to make a professional judgement as to whether or not the proposed samples are likely to be sufficiently representative such that the sampling will be worthwhile. Such judgement needs to be exercised by personnel who understand the principles of sampling, as they apply to the stream being sampled. There are many circumstances where available methods for sampling of a particular stream will be meaningless, and in such circumstances analytical data from that sampling will only serve to propagate poor decision-making.This paper outlines the approach for the guide, the areas it covers and the approaches adopted for different types of unit operations and associated equipment configurations.CITATION:Atkinson, B W and Docherty, J, 2017. A practical guide to sampling in coal preparation plants, in Proceedings Eighth World Conference on Sampling and Blending , pp 241–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By R Fletcher

Pacific Hydro, a leading renewable energy company from Australia, is developing a series of cascading run-of-river hydro electricity projects in the Cachapoal Valley at the base of the Andes Mountains some 100 km south of Santiago in Chile.These projects involve extensive tunnelling and underground works. The first of these projects is called Chacayes (110 MW installed capacity) and is now under construction with Astaldi SpA of Italy and Fe Grande of Chile as the EPC contractor. Astaldi SpA also has an equity stake in the project. It involves 6 km of tunnels between 5 m and 7 m diameter, of which 2.3 km is by tunnel boring machine (TBM) (5 m diameter).This paper outlines the local and regional geology, the scope of the Chacayes project, actual tunnel excavation rates and support, and compares the decision making on Chacayes between a choice of traditional drill and blast excavation versus TBM.The paper also outlines the next project planned to be developed by Pacifi c Hydro in the valley – the 140+MW Nido de Aguila project involving a main tunnel drive of 11 km with two intermediate adits, plus a 388 m shaft and underground powerhouse. The main tunnel drives are likely to be excavated by two hard rock TBMs (5 m diameter) but will need to be able to withstand high overburden pressures of up to 1300 m.Subsequent projects in the planning stages include the downstream Coya II project with two tunnels totalling approximately 10 km, one of which may be by TBM.

Mar 8, 2011

By De Broglio R

The Mae Moh coal deposit was discovered some 60 years ago by villagers who noticed spontaneous combustion of coal outcrops. The first production began in the 1950's to fuel a fertilizer plant and a 12.5MW power station. During the period 1976 to 1979, three 75MW power station units were constructed on site. These have a total daily coal consumption of some 5000 tonnes and are served by a stockyard of approximately 60 000 tonnes total capacity. Stacked coal is reclaimed by means of a front end loader onto reclaim conveyors. During the years 1983 to 1986 four 150MW power station units were constructed east of the eastern seam subcrop, sons 2 km from the original power station complex. These have a daily coal consumption of nearly 12000 tonnes and are served by a stockyard of total capacity 270000 tonnes, equipped with two stackers and two bucket-wheel reclaimers for a totally mechanised system.

Jan 1, 1986

The Porgera gold mine has made significant progress with the successful installation of a JK FrothCam image analysis system. The system is used to measure and control froth velocity on the scavenger circuit which has brought significant economical and operational benefits. The froth velocity signal, determined by analysis of the camera, is transmitted to the PLC that manipulates flotation cell airflow rate and cell level controllers to maintain a target froth velocity of 130 mm per second. Following on from a three-week trial installation in June 2000, a permanent installation was commissioned on the scavenger Outokumpu (OK150) tank cells. Further work is in progress on the rougher Wemco cells. This paper describes the evaluation of FrothCam Technology and its subsequent installation.

Jan 1, 2003

By Yoshii Y

Many kinds of shield machines are being driven in the soft ground of Tokyo metropolitan area. Tunnel alignments for underground power transmission lines are generally planned to pass under public roads where facilities, especially life-line facilities, are densely located. Therefore, it is frequently required to drive the shield machines along very sharply curving routes. This paper reports on the performance of the new shield machine - the Sharp Curve Excavation Shield Machine - developed by Tokyo Electric Power Co., Inc., which can freely drive along a much sharper curve than conventional machines. Some of features of the developed devices of this machine are, maximum flexing angle of 6.5 degree in all deirection at the middle of shield body, maximum bending angle of 3.5 degree in all direction at the cutter disc, and so on. This shield machine can there- fore drive along curve of minimum radius 15m. The machine was confidently applied to the const- ruction of tunnel in soft clay strata at N values 2 to 5. Outer diameter 3.7m. Length 202m. Horizontal curve; radius 15m, length 20m x 2. Vertical curve; radius 30 m, inclined driven up 29%. The behaviors of the shield machine, segments and surrounding ground were monitored during construction for safety and efficiency check of this machine.

Jan 1, 1987

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

Rosebery Mine is situated on the west coast of Tasmania and is AustraliaÆs largest volcanic-hosted base and precious metals deposit (zinc, lead, copper, gold and silver). The milling operation has been producing zinc, lead and copper concentrates continuously for over 100 years. RoseberyÆs long life demonstrates the operation to be high grade, and high margin, capable of operating through several commodity price cycles. Paradoxically, throughout this long history the ælife-of-mineÆ as defined by proven and probable reserves has been short. Zinifex has demonstrated its commitment to discover the future of Rosebery with the growth project æProject HorizonsÆ. The aim of the project is to extend the life of mine beyond 2020, with an additional exploration expenditure of $19 million over three years. Despite the maturity of the deposit, early success has confirmed the potential with the discovery of new resources. Mine planning strategic studies are challenging established paradigms of mine production, throughput rates and metal cut-off grades. Discovering the optimal process rate for Rosebery, by examining the æHill of ValueÆ and underground mine optimisation is proving critical to the best exploitation of RoseberyÆs rich resources. The promise of finding a mine within a mine is being realised, with new lenses being delivered by exploration success and real grade/tonnage options optimised through dynamic mine planning. The future of Rosebery is co-dependent on these two areas of discovery. This ensures capital expenditure decisions are informed, to secure the next 20 years of wealth creation and beyond.

Jan 1, 2008

The hoisting system at the Newcrest Telfer mine is designed for a final duty of 7.35 million tonnes per annum at a hoisting distance of 1450 m. In terms of hoisting capacity (t/h) times hoisting distance it is one of the largest friction hoist installations. Initially, the hoist will be equipped for hoisting 6.5 Mtpa from 1100 m depth. This new drive technology is now well proven by ABB for mine hoist applications with the first installation in commercial operation since July 2001. To date 17 systems for medium voltage drives and another five for low voltage drives have been purchased from ABB for mine hoists. This paper will also deal with skip design and powerful data loggers with diagnostics for local and remote monitoring that are installed in the Telfer mine hoist.

Jan 1, 2005

By R J. Wood

Raise drilling (or raise boring) is not a new technology or methodology. The first raise drilling machine was developed by The Robbins Company (TRC) of the USA in 1962. TRC manufactured the first tunnel boring machine (TBM) in 1952 and Jim Robbins, the founder of the company wanted to ‘turn the TBM concept on its head’ so to speak.Many improvements have ensued in the 50 years since the first machine. Such improvements include advances in the drill rod and thread design, cutters and reaming heads. Raise boring would not have been possible without the development of the tungsten carbide insert cutters and there have been big advances in both the carbide technology and in the mechanical design of the cutters.Over time mines have developed deeper with a greater use of diesel equipment resulting in greater ventilation requirements. This in turn means larger and deeper ventilation shafts. There have also been improvements in directional drilling techniques. This all combines with the need and ability to construct larger shafts using the safe method of raise drilling. With suitable geotechnical conditions the RBR900VF is capable of drilling shafts to a diameter and depth of greater than 8 m and 2000 m respectively. Greater diameters are possible over shorter lengths with suitable ground conditions.The RBR900VF was designed and manufactured to specifications developed by Macmahon. This machine has the greatest thrust and torque capability of any machine in the world. It enables cutters to be more heavily loaded in the larger diameter heads and this is essential for efficient rock excavation. Additional features of the new machine include minimal manual handling to provide a safer working environment and higher strength steel for the drill rods providing additional safety margin.CITATION:Wood, R J, 2014. A revolution in raise boring – the development of the RBR900VF, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014