Search Documents

By Hayes P. C

The reduction of small, dense zinc oxide (ZnO) samples in CO/CO2, and CO/N2 gas mixtures has been investigated at temperatures between 900 and 1100¦C. The microstructural characterisation of the reacted and partially reduced samples was complemented with measurements of the rates of the reactions. The mechanisms and kinetics of reduction of zinc oxide were found to be dependent upon the CO partial pressure, the oxygen potential of the gas mixtures, temperature and degree of reduction.

Jan 1, 1991

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By B D. Saffron

In 1983, open cut coal mining operations were suspended at the Tent Mountain coalmine, located in Alberta, Canada in an area called Crowsnest Pass. Montem Resources (‘Montem’), an Australian mining company, purchased the asset in 2016. They conducted several drilling campaigns and undertook environmental monitoring with the intent to restart operations. In 2020, Montem completed a Definitive Feasibility Study, which indicated a mine life of more than 14 years.

Aug 2, 2023

By Doyle R

Underground operations commenced at Tower Colliery in late 1978 and the early prevailing mining conditions in the worked seam were considered poor as a result of high stress and geological disturbances. This suggested that outbursting activity may be a possibility. The colliery has since recorded a total of 13 individual outburst incidents, all of which have been associated with the same dyke and strike-slip fault zone. This paper depicts the geological conditions and presents the results of investigations undertaken at the time of these outbursts.

Jan 1, 1986

With the sinking of the No. 3 Shaft and the erection of a changehouse nearby, a sub-brace level structure was provided incorporating a time office, underground foremenÆs office and lamp room, in conjunction with a covered walkway, ambulance room, fire station and waiting brace.

Jan 1, 1957

By M Ozkayhan, N Arslan

"The Efemçukuru underground mine in western Turkey is an intermediate sulfidation, epithermal gold deposit. The bulk of the mineral resources and all of the mineral reserves lie within the Kestanebeleni (KB) vein system. This system comprises four spatially-distinct mineralised zones: the south ore shoot (SOS), the middle ore shoot (MOS), the north ore shoot (NOS) and the KB north-west ore shoot. Production currently occurs only in the SOS, MOS and NOS zones. The gold mineralisation is very fine grained and occurs as free grains in quartz and carbonate, and as inclusions in sulfide minerals. Gold is recovered as part of a sulfide concentrate by flotation methods. Though hosted in the KB vein, the gold mineralisation is not evenly distributed within the veins. Definition of its occurrence is totally dependent on diamond drilling.Diamond drilling at Efemçukuru is done with its own equipment and staff, all managed by the mine geology group. The process over the mine’s six year production history incorporates continual improvement with an innovative approach by focusing on the following: drill team organisation career development and training product research and effective equipment management cost reduction planning and scheduling of development for drill stations.Over 40 000 metres of mostly BQ size core are drilled annually by three drill rigs at a cost approaching US$35/m.The planning and execution of the drilling pattern depends on the configuration of the ore shoot and the planned mining method. Ore extraction is mainly by drift and fill mining augmented by about 15 per cent longhole stoping. The drilling of a specific area is scheduled to be finished 3 to 8 months prior to mining. This scheduling is sufficient for short-term grade model updates and any needed changes to the planned development or stope sequencing prior to planned production from the stope area.CITATION:Arslan, N and Ozkayhan, M, 2017. Diamond drilling at Efemçukuru gold mine, Turkey – a case study on the benefits of timely and cost-effective drilling to short-term planning, in Proceedings Tenth International Mining Geology Conference 2017, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By R Hargreaves, T Elkington, W J. Shaw, G W. Booth

Every day, around the world, thousands of tons of ore are loaded onto ships completing the miningproduction process and starting a multimillion-dollar economic transactions process. These transactions are based on the supply of tons of a commodity with certain specifications of assays of the main element (or physical properties) and concentration of contaminants, which are finally verified and evaluated by buyers, and also are considered ‘as true’ during Reconciliation process. On Sample Stations, this ‘true’ is based on a few kilograms of sample, often representing thousands of tons, that are sent to laboratories for further sample preparation and chemical analysis, where finally assay information is obtained from a few grams of pulverised sample, and are used for further production, planning, operational and financial-marketing decisions. Different International Standards (depending on the commodity) are used to establish the methodology to be followed, to set-up and obtain samples from the Sample Stations, and the specifications are visually inspected to give an estimation on the performance of the sampling point. This paper seeks to highlight with examples, the importance of the implementation of a continuously monitored Quality Program (QAQC and QM) on Sample Stations, focused on the parameters that directly affect the quality and representativeness of the samples. By this implementation, a proactive approach and better-informed decisions can be taken for mining companies to: a) quantify/improve production and reconciliation results, and b) to supply the right specifications of shipped ore, increasing the value of the Resources. Finally, laboratory results are normally used as an indication of the quality of the information applied for the economic transaction, but it should be considered, clarified and highlighted that the laboratory will only process and analyse a sample obtained from a Sample Station, and potential problems on bias or precision may occur in stages prior to the laboratory reception. Hence the importance of the implementation of a quality assurance program that protects multi-million dollar decisions.

Mar 22, 2022

By J Light

Since 2019, the mine planning team at Olympic Dam has been establishing and maturing a shift from deterministic to probabilistic scheduling techniques. This paper outlines this journey undertaken by the mine planning team, key learnings from implementation and further work required to increase the level of planning maturity. Olympic Dam (OD) is a highly variable, polymetallic orebody with a vertically integrated value chain from operations to final product. The processing plant has a tight set of quality constraints which are managed through timing of stopes from varying parts of the orebody. Value is eroded for the operation when forecasted quality of the mine feed encounters disruptions from unplanned changes to the timing of stope starts. As production has moved from the historic Northern Mining Area into the more geologically complex Southern Mining Area, average stope size has reduced, resulting in increased mining fronts required to meet production targets. This has created a problem of increased schedule complexity and difficulties in identifying and communicating resource priorities within a large set of individual stope critical paths. The problem was approached by considering each stope as an individual project constructed by teams working across multiple projects at any one time. The operation could then be considered a multi-project environment with shared resources and enables the application of Critical Chain Project Management (CCPM) to the mine plan. Key to CCPM is the addition of time buffers to protect the critical path of a project form upstream or downstream processes. Implementation of time buffers protects the stope start date against compliance to plan variance. The monitoring of each time buffer consumption, as a proportion of total construction activities completed enables proactive prioritisation of resources. This resulted in an increase in the number of stopes starting in accordance with the mine plan, simplified communication of priorities to all levels of the operation, increased compliance to plan and a clear measure of schedule risk during planning routines.

Mar 29, 2023

By Porter I, Singh RN

An advanced elasto-plastic finite element model adopting a modified Von Mises yielding criterion was used to simulate progressive failure of the rock strata surrounding a room and pillar mine structure. The model conformed to the strain-softening behaviour of rock and accounted for post-failure residual strength. The simulation was achieved in such a way that material values were updated after each FE run, according to the stress criterion until the solution reached the final equilibrium steady state of the mine structure. The suggested structural stability analysis approach accounted for the main features of the structure degradations produced during loading through changes in rock material stiffness and subsequent evolution of stresses. Comprehensive parametric analysis was performed and the inevitable effect of interaction of the roof, pillar and floor on the overall mine stability limit was investigated. The numerical results clearly showed that linear models could not realistically represent the true behaviour of the mine structure. The results obtained are in good agreement with that predicted in the field.

Jan 1, 1992

The Imperial Smelting Process (ISP) for the simultaneous smelting of zinc and lead was developed at Avonmouth from the 1930's with activity intensifying in the late 1940's/early 1950's. Present operations are based around the No.4 furnace which was built in 1967. Development during the 1980's has been driven by the need to sustain operations at low metals prices and has been aimed at reducing manning whilst increasing output. Although hit by several major plant disruptions, progress has been steady, culminating in a ú10 million capital programme in 1988?89 to upgrade the operation. The most important technical developments, reflecting the needs of the 1990's have, in the sintering area, included improvements to feed conditioning and sinter quality, a 20% uprate in production capacity by debottlenecking, and pilot work leading to the installation of a Boliden-Norzink mercury removal plant. In the smelting area the ISP furnace has been rebuilt, with a redesigned bottom section to eliminate earlier operating sensitivities, and to achieve higher blowing capability, and at the zinc refinery the columns have been rearranged for more flexible operation and higher capacity.

Jan 1, 1989

By Grano S. R, Lauder D. W

Investigations on the oxidation behaviour of chalcocite and its rejuvenation by hydrogen sulphide ion have been undertaken. Chalcocite oxidation was measured using X-ray photoelectron spectroscopy (XPS), zeta-potential and by dissolution in et

Jan 1, 1997

By L C. Thompson

This paper examines six sites in Northern Nevada where soils and groundwater have been contaminated with petroleum hydrocarbons and/or organochlorine compounds. All six of the sites studied are located in an arid, highly mineralised area of the Great Basin. As a part of the original geochemical investigation to determine the applicability of biodegradation in the remediation of petroleum impacted soils and aquifers extremely high levels of uranium, vanadium and molybdenum were detected in the anaerobic groundwaters associated with some of the hydrocarbon plumes. Some groundwater uranium concentrations exceeded 7 ppm while vanadium and molybdenum concentrations reached almost one ppm. The bioleaching appeared to be most effective under methanogenic conditions and was noted in both high sulfide and low sulfide environments. Background concentrations of uranium in the formation were measured between 6 ppm and 109 ppm and highly dependent upon depth with the highest levels being found in association with evaporites. Unlike uranium, vanadium tended to concentrate in free-floating organic fractions reaching levels as high as 2000 ppm in the layers of jet fuel floating above the groundwater. Molybdenum was the most resistant of the three metals to bioleaching.

Jan 1, 2004

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

The initiation of cast Pentolite primers by detonating cord has been examined by the combination of two different experimental techniques with computer simulation by the finite element hydrodynamic code DYNA2D. In the first type of experiment, the cord/primer system was placed in a water aquarium, and photographed using a high-speed image converter camera. This highlighted the emergence of the detonation front through the primer surface and the generation of shock waves in the surround- ings. Numerical simulation was used to interpret the experimental record, establishing where the cord had induced buildup to detonation inside the primer. The second experiment used the plate dent test, where the primer was placed in contact with a block of metal (here aluminium), with the resul- tant dent in the metal surface being a measure of primer output. Detailed numerical simulation of this test confirmed that the observed dent was caused by the development of a complex series of shock waves inside the Primer.

Jan 1, 1988

By J Loeb, R Ramanathan, H Ingham, P Cameron

Most mining operations, including iron ore, maintain a focus on continuous improvement and asset optimisation in their operations. As all the unit operations in the Mine-to-Mill value chain are interdependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and impact of changes to the process. In this paper, we discuss some of the critical attributes in the Mine-to-Mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve Mine-to-Mill processes. Mining operations are planned and executed based on designs and models to achieve the operation's objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Therefore, measurement of the key attributes establishes the baseline for Mine-to-Mill (or Pit to Plant) performance, which is necessary to understand the impact of any proposed improvements to the process design and execution and monitor the outcomes on an ongoing basis sustain the improvements that have been implemented. This paper focuses on two types of measurement – blast movement and particle size of materials through the Mine-to-Mill process. Several innovative technologies and control loops are readily available to measure these attributes and assist operations to improve productivity and mine site profits. The size of the tangible benefits, which can flow from measuring and optimising fragmentation and blast movement, provide a remarkable return on the investment. Realising these benefits needs a focus outside conventional operation silos as a successful Mine-to-Mill project requires a multidiscipline approach across all the silos in the value chain. Required technologies are available; adding the necessary ingredients of communication and co-operation by all concerned across the silos will ensure the benefits are realised.

Nov 8, 2021

Comparatively recent Tasmanian legisla tion established a series of rigid control standards for environmental protection just as ma spectacular expansion of the mining industry was nearing completion. Upgrading existing protection to obtain the necessary licence to operate under these new regulations required further major works and involved a considerable outlay of non- productive capital at a time when escalating costs and falling metal prices were straining economic efficiencies to the limit. Late in 1974 a major environmental protection scheme was commissioned by the Electrolytic Zinc Company of Australasia Limited at Rosebery on the West Coast of Tasmania. This 4 million dollar project was specifically developed by the Company ahead of and to meet the new standards for control of total effluents discharged from its zinc-lead -copper-pyrites mine and concentrator.

Jan 1, 1977

By J A. van Niekerk, J G. Jardine, J W. Olivier

The Runruno Gold Project is located on the island of Luzon, approximately 200 miles north of Manilla in the Philippines. The mine is an open cut operation and uses the proven BIOX® and carbon-in-leach (CIL) processes to recover gold, and the ASTER™ process for detoxification of the CIL residue prior to discharge to the Residue Storage Impoundment (RSI). Work to date has defined a mineral resource of 1.39 million ounces (Moz) of gold, and the operation will produce 96 700 oz of gold per annum over a mine life of 10.4 years. The BIOX circuit is designed to treat 140 000 t/y of concentrate with a design capacity of 404 t/d of concentrate at a design sulfide sulfur grade of 17% S2-.The Runruno BIOX Plant is the first application of the Outotec BIOX Generation III design principles, focussing on ease of operation and maintainability. During development and implementation, the project team focussed on identifying opportunities to optimise the capital efficiency while not compromising on the operability or overall efficiency of the process or the equipment. The BIOX plant also incorporates the latest developments in the design of the BIOX agitators for more efficient mixing and gas dispersion. This paper will discuss some of the critical aspects and decisions taken during the development and implementation of the BIOX Process at the Runruno Gold Project. The paper will highlight some of the factors affecting the commissioning process as well as the improvements seen through the introduction of the Generation III BIOX design principles. CITATION:van Niekerk, J A, Olivier, J W and Jardine, J G, 2017. Implementation of the BIOX® process at the Runruno Gold project, in Proceedings MetPlant 2017, pp 218–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D R. Seaman, R P. Tooher, B A. Seaman

"Several mine scheduling tools exist for use in optimising and scheduling the reserve according to in situ value. These tools generally value the ore on a per block basis according to regressed recovery models based on ore grade and type. It is then the task of the plant metallurgist to ensure that these ore blocks are fed to the plant in a manner that satisfies the prevailing plant constraints. This task is often completed in complex Excel® spreadsheets that are modified over time with factors applied to account for plant modifications or limitations.It is the authors’ experience that this approach is difficult to audit and replicate in a consistent manner. Furthermore, operational decisions, such as primary grind size or autoclave oxidation are made on the metallurgist or managements’ perceived optimum value and does not necessarily represent a cash flow based optimum.Many processing plants contain multiple internal constraints. As ore feed grades and properties change over the life-of-mine (LOM), processing-bottlenecks shift from one unit process to another and different operating strategies need to be adopted to maximise cash generation from the process.This paper presents a unified optimisation approach to scheduling ore based on a circuit mass balance to describe the process plant with individual models for each significant unit operation. The approach allows for optimisation over multiple input variables and the inclusion of linear and non-linear constraints.This optimisation process has been applied to different complex gold operations. The end result is an automated scheduler that selects the optimum blend of ores as well as plant operating conditions that satisfy all internal plant and shutdown constraints while maximising the objective of choice (metal production or cash flow). The models are also valuable for evaluating expansion or debottlenecking opportunities of individual processing units. These models are coded in Matlab® R2016a provided by MathWorks®, and can be deployed to end users in a compiled version with significant savings in time to run different scenarios over the Excel®-based systems.Citation:Seaman, D R, Tooher, R P and Seaman, B A, 2016. Optimisation of Complex Gold Processing Plants with Multiple Unit Operation Constraints - the Newcrest Planning Scheduler, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A K. B Opitz, M Becker, J L. Broadhurst

"One of the key drivers of geometallurgy is to define the ore characteristics and their variability to build a geometallurgical model. The inclusion of waste rock properties and their variability is just as important, given that the generation of acid rock drainage (ARD) poses one of the most significant environmental challenges facing the mining industry. Formed through the oxidation of sulfide minerals in the presence of oxygen and water, ARD generation is exacerbated through the regeneration of lixiviates by naturally occurring iron- and sulfur-oxidising micro-organisms. In order to manage the potential risk of ARD pollution, timely, accurate, reliable and robust characterisation and prediction of the ARD potential of waste material is critical from an early stage in the mining process.This study demonstrates the use of the biokinetic-accelerated weathering test developed at the University of Cape Town to characterise the ARD potentials of gold waste rock samples under microbial conditions. These tests are performed in conjunction with standard characterisation tests to provide an indication of the potential for ARD generation under both chemical and biological conditions. Results provided information regarding the relative rates of acid neutralisation and acid generation, with the contribution of specific minerals to the observed behaviour considered through use of a detailed mineralogical assessment. Overall, the addition of the biokinetic test to the current geometallurgical characterisation and prediction toolbox will allow for relatively rapid assessment of the bulk kinetics of ARD generation.CITATION:Opitz, A K B, Becker, M, Broadhurst, J L, Bradshaw, D J and Harrison, S T L, 2016. The Biokinetic Test as a Geometallurgical Indicator for Acid Rock Drainage Potentials, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 183–192 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014