Search Documents

By Menne D. M, Ladyman R

Camel Creek Mine operated by Lynch Mining Pty Ltd is located 65 km west of inghain and 160 kin north west of Townsville in North Queensland. (Figure 1). The Camel Creek gold mineralisation was discovered in mid-1987 in an area previously known for its tin workings. Mining commenced in January 1989 after an oxide reserve of 1.2 million tonnes @ 2.1 g/t gold had been delineated. The first gold pour was in May 1989. The mine developed into a medium sized open cut operation, with full site facilities. The initial mining rate was 500 000 tpa utilising run-of-mine (ROM) heap leaching to recover the gold. By the end of 1990 the wider orehodies were mined and efforts were focused on the narrow orebodies, of width typically less than three metres. Smaller earth moving equipment was employed to selectively mine the narrow orehodies leading to a decrease in the mining rate to 200 000 tpa. The Red Gold deposit (80 000 tonnes « 3.0 g/t to 18 in vertical) was mined in mid-1990 and ore was hauled approximately 8 kin to the Camel Creek heap leach operation. The ore was hauled in a dedicated campaign after being stockpiled. The cost of dedicated ore haulage ensured that only the more exceptional of the remote orebodies could be mined in this manner. The Golden Cup orebody, some 20 km from Camel Creek, was too distant to permit ore haulage. However, this prospect contained sufficient gold (initially 90 000 tonnes @ 3.0 g/t) to warrant the installation of a small mobile adsorption facility. Construction of the second heap leach operation commenced in late-1990. Gold production commenced in early April 1991. Mining of several smaller orebodies remote to the second heap leach facility has been undertaken and further mining is planned. This paper outlines heap leaching practice at Camel Creek Mine and summarises the success of the Golden Cup heap leach.

Jan 1, 1994

By I Gray

This paper examines the practical limitations that affect the measurement of stress in rock. As most rock stress measurement is conducted through the invasive process of drilling a hole in a rock mass, the nature of the rock and its response to being drilled form the basis of the stress measurement process. The prime techniques to measure stress down a borehole are to conduct hydraulic fracturing and its variant hydrojacking, overcoring, and the examination of the borehole wall for breakout or tensile fracture. It is also possible in some circumstances to use the sonic velocity within the rock mass as an indicator of the stress situation. Other structural indicators of stress such as joints, faulting and intrusions are useful but may not reflect the current stress situation within the rock mass. The variability of stress within the rock mass also needs to be considered as it is quite unusual to have a monotonic stress situation throughout any rock mass. The outdated concept of measuring the far field stress in a few measurement for use in a numerical model is quite dangerous. It is essential to make multiple measurements and to generate an understanding of its distribution in some form of model before stress can sensibly be incorporated into underground design. CITATION:Gray, I, 2018. The practicalities of effective stress measurement in rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 360–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Jones J. P, Arriagada J, Scherpenisse C. R

A recently-developed model is used as a tool to optimise the design of blasts used to create final walls in large open pit mines. The use of this tool has allowed present blasting practice and proposed designs to be evaluated to predict the likely extent of rock damage behind the final wall. The evaluation of the damage is dependent on the predominant local geology. Modelling of damage using the software allows the potential zones of rock damage to be evaluated under the following criteria: I . the extent of new fractures formed in the intact rock mass; and 2. the distance to which dilation and extension of existing discontinuities and pre-existing fractures will likely occur. The computer model has been used to examine present blasting practice and to estimate the damage induced by final and intermediate rows of blastholes. The results of current practices are presented in a visual form that allows simple comparisons to be made for any proposed changes in design. To confirm the predictions of the modelling, physical measurements are being undertaken at selected mines to quantify damage behind blast patterns, and experimental programs are underway to measure near-field vibration, or shock, levels. The computer modelling software is being used to qualify and improve the design of final rock slopes in large surface mining excavations, and to provide site engineers with well-defined design criteria for consistency in design. The model is seen to be just one of many tools which are being used in large open cut mining operations to gain an improved understanding of blasting and blast control.

Jan 1, 1995

By J M. F Clout

The Roy Hill Project is an independent integrated port, rail and mine development in the Pilbara region of Western Australia. The bankable feasibility study for the project was completed in January 2011 by Roy Hill Holdings Pty Ltd, a wholly owned subsidiary of Hancock Prospecting Pty Ltd. The Project will deliver 55 Mt/a of premium quality iron ore to a rapidly growing market with a mine life of over 27 years. This study is based on exploiting a 1.2 Bt bedded resource of microplaty haematite-rich Marra Mamba, from which 562 Mt of reserves has been delineated to date. A further 1.1 Bt resource of detritals and low grade bedded is proposed to be mined once the bedded high grade resource is depleted. Roy Hill lump and fi ne ore products will compete strongly with other Pilbara products. As a low cost producer, Roy Hill is on track to capture four per cent of the global seaborne traded iron ore market. The project decision to proceed is targeted for Q2 2011 to enable first ore on ship by Q2 2014.

Jul 11, 2011

By M Svartsjaern, D Saiang and K Mäkitaavola

The Kiirunavaara mine is a large-scale (28 Mt/a) iron ore mine located in northern Sweden. The mine is owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB) using sublevel caving (SLC). The SLC area underlies an open pit decommissioned in the 1950s, the current main SLC haulage level is situated at an depth of 1100 m. The main orebody dips 60 degrees to the east with a distinct boundary defining the hanging wall to the east and footwall to the west. Since the 1980s damage has been observed both in the footwall rock mass as well as on the footwall crest of the open pit. Recent investigations indicate that the underground footwall damage is primarily controlled by large-scale slope failure mechanisms. Structurally controlled near-vertical planar shear failures in the upper footwall appear to be driven or facilitated by a step-path like curved shear failure situated in a zone starting ca 250 m, and intersecting the SLC about 100 m above the active mining level. To confirm this failure evolution a pilot underground measuring system has been designed and installed to monitor the expected rock mass displacements indicated by numerical models based on the above mechanisms. The systems consists of 50 m time domain reflectometry (TDR) coaxial cables installed in the footwall both across and away from an estimated damage extent boundary to monitor shear movements along natural joint surfaces. The TDR installation is combined with long extensometers to facilitate differentiation between diffuse shear and rock mass normal expansion. Additionally, a low-tech system of tape extensometer lines are installed in drifts and stopes running perpendicular to the ore strike to monitor horizontal displacements in the infrastructure as the footwall ‘slope’ loses confinement during mining advance when the mined out areas are replaced by caved rock from the hanging wall.CITATION:Svartsjaern, M, Saiang, D and Mäkitaavola, K, 2016. Underground footwall monitoring at the sublevel caving mine – Kiirunavaara, Sweden, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 773–780 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The Woodcutters deposit, 65 km south- southeast of Darwin, N.T., consists of a series of veins of pyrite, sphalerite, and galena with some silver, cadmium, antimony, and arsenic minerals. The veins are hosted by the Early Proterozoic Whites Formation, a sequence of black slates with interbedded carbonate rocks and minor ash tuffs. The known orebodies occur about 300 to 500 metres above the contact of Whites Formation with the underlying Coomalie Dolomite, which consists of dolomite and magne- site. The stratigraphic setting is lithologic- ally similar to that of the Mt. Isa deposit, Queensland. The orebodies are replacement veins occ- urring along fault and dyke structures which are sub-parallel to the axes of a double-nosed faulted anticline. The orebodies are in part associated with two unusual carbonatized lam- prophyric dykes. The dykes were intruded after the fold and its slaty cleavage were formed. The ore has replaced the dykes and host rocks and is therefore late-stage hydrothermal miner- alization. The known orebodies are open at depth. A "bonanza" of high-grade ore occurs at the upper part of the largest orebody and is currently the subject of an open cut mine planning study by a consortium of companies headed by Nicron Resources Ltd.

Jan 1, 1984

Indiscriminate surface disposal of coal waste in New South Wales has created a serious fire hazard and increased air pollution.A survey of numerous dumps, as well as particular investigations of one badly-constructed dump, showed that factors conducive to ignition and propagation of fires in waste dumps were high contents of combustible material (coal, pyrite, wood. paper. grease), size segregation leading to ready movement of air and moisture shape of the dump (e.g. protruding sections or porous junctions), high ambient air temperatures, bush fires, and even deliberate lighting.Control methods applied in the past tended to be haphazard and unsuccessful. Under Australian conditions the technique recommended for control of existing dump fires, based on experimental work, is to spray the dump with a chemical fire retardant (e.g. a 2 per cent solution of sodium tetra borate and ammonium phosphate), to cover the dump with a suitable soil, and to seal the surface with a I per cent solution of aluminium sulphate or sodium metasilicate. The recommended method of dump construction to prevent fires is to level and seal the site, to construct a firebreak around the dump area, and to build a rectangular dump with minimum size segregation and compacted surfaces.

Jan 1, 1971

By D Pearce

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By S Morgan, D J. Bradshaw, S Schwarz

The characterisation of the flotation kinetic response in future mining deposits is important because the flotation response is affected by changes in ore mineralogy. Current methods for characterising the flotation response of different ore types, such as the JK floatability index test (JKFIT) methodology, require at least 10 kg of feed material. In geometallurgical applications, this material is taken from core samples. Core samples are generally obtained using specialised drills and are limited in nature. Thus, it would be beneficial to develop a laboratory technique that required less sample material but still characterised the flotation response of different ore types. The JK mineral separation index (JKMSi) is a small-scale flotation test that requires significantly less feed material (10 g of sample/data point). This study aims to investigate the JKMSi system kinetics and to validate this technique using the JKFIT proven methodology. The JKMSi flotation kinetics were manipulated by varying selected system parameters. The relationship between these parameters and mineral recovery was used to obtain floatability characteristics of the ore. For an ore sample containing chalcopyrite and pyrite, it was found that the chalcopyrite floatability parameters determined from both the JKMSi and JKFIT tests were of the same order of magnitude and the mass fractions of the fast, slow and non-floating components were similar. For pyrite, the floatability parameters were not of the same order of magnitude, but modifications to the test procedure have been identified, which may correct this.CITATION:Morgan, S, Bradshaw, D J and Schwarz, S, 2012. Julius Kruttschnitt Mineral Separation Index - Small-scale test to characterise the flotation response of an ore type, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 159-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Sengstock G. W, Spathis A. T

Benchmarks of mine equipment involved in the excavation process of coal mines would suggest that such equipment is not always operating at an optimum level. Dragline operations and truck/shovel operations rely on efficient use of their plant in order to maintain high mine throughput. The first process which affects the material to be excavated is the drilling and blasting process. Drilling and blasting delivers a fragmented material with a given disposition ready for excavation by mine equipment. As mine operators demand more productivity from their major excavating equipment, many sites are considering the use of productivity monitors to measure their outputs. Some of these productivity improvements will be directly related to the drilling and blasting process, so that as the monitoring systems improve, the opportunities to evaluate all drilling and blasting variables will also improve. This paper reviews current and newer methods for monitoring equipment productivity in mines. These include simple time and motion studies obtained by either manual timing of processes or by automated data collection equipment being adopted by the industry. Case studies for truck/shovel operations are discussed and the productivity improvements are compared with typical industry standards. These improvements relate specifically to parts of the load, haul and dump cycle and the potential for significant improvements are identified. Particular opportunities for drilling and blasting improvements are also presented.

Jan 1, 1995

Gold-rich porphyry copper deposits areimportant sources of gold in the circum-Pacific region: 26 major deposits contain >7000 tonnes of gold. The deposits occur in a variety of subduction-related settings, and may be underlain by crust that is undergoing either extension or compression and that is either oceanic or cratonic in character. The deposits are associated intimately with composite porphyry stocks, which commonly were emplaced into coeval andesitic volcanic piles. The stocks range in composition from low-K calc-alkaline through high-K calc-alkaline to potassic alkaline. Much of the copper and gold were introduced as components of K-silicate alteration, which may undergo partial overprinting by intermediate argillic assemblages. Advanced argillic alteration is widespread in the shallow parts of the systems whereas sericitic alteration at deeper levels tends to be restricted. Gold distribution generally follows that of copper, which is present mainly as chalcopyrite with or without bornite. The gold is in the native state and occluded by cr in close proximity to the copper-iron and/or iron sulphides. The magmas and metals necessary for the generation of gold-rich porphyry deposits were derived mainly from subcrustal sources, with the subducted slab believed to play a pivotal role.

Jan 1, 1990

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By G Harbort

The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to convert spatial geological data into metallurgical information to drive production and mine planning, blast design, blending strategies and plant set-up. Increasingly the process designer is required to interface with geological and mining staff to propose the best investment strategy for a project’s benefit.The geometallurgical model development for the Zafranal copper-gold project commenced in March, 2010, several months after the start of a major drilling campaign by AQM Copper Inc. The initial evaluation stage required review of historical Teck RC data to determine areas of metallurgical interest within the project. As drilling transitioned from RC to diamond drilling, core that was considered representative of the resource was selected and subjected to MLA mineralogy analysis. When coupled with sequential copper analyses this allowed calibration of an assay derived mineralogy model, allowing process concept options and a preliminary test program to be developed. This Phase 1 test program provided a preliminary process design, operating costs and anticipated concentrate grades and recoveries. Both this data and resource estimation were used to generate a preliminary Whittle pit optimisation based on maximising net smelter return, which in turn fed into a preliminary mine plan. The preliminary mine plan, in conjunction with geological logs and core results was used to develop a phase 2 metallurgical test program, where variability tests were conducted throughout the resource and composites formed to investigate specific years of the mine plan in locked cycle flotation. In addition comminution tests were modelled against geometallurgical domains allowing comminution components values to be calculated for 36?000 m of core. A flotation geometallurgical model was developed and incorporated into the resource model allowing concentrate grades and recoveries to be estimated on a block-by-block basis.

Sep 5, 2011

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By L Blackwell

Strategic mine scheduling is an industry best practice for increasing the long-term value of mining operations and supply chains. The application of optimisation technology such as mixed integer linear programming (MILP) is able to achieve a mathematically optimal result for a given scheduling model. Such a model will typically define the available source material, processing options and desired constraints for accessing and processing the material. Most strategic scheduling models, however, do not include a sufficiently detailed model of capital expenditure options related to capacity expansion.Typical strategic schedule models do not include important capital expenditure features such as capacity decay or expiration (limited lifespan of trucks), precedence relationships over time (rail construction before a new plant or non-linear expansions due to economies of scale) or mutually exclusive option sets (choices of plant size). By not including these features, a strategic mine scheduling model for a capital-sensitive operation is unable to be optimised to deliver maximum value or profitability.This paper presents several results of MILP optimisation using advanced capital expenditure modelling for mining operations and supply chains. Results of the study demonstrate that optimising capital expenditure at the same time as optimising the mining schedule allows for minimisation of capital purchasing, optimal timing for those purchases and optimal scheduling around them. Overall, this results in an increase in net present value.CITATION:Blackwell, L, 2014. Capital expenditure modelling for strategic mine scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

The South American mining community leads the world in recognition and adoption of the latest grinding mill relining technologies. Clearly this region has recognised the benefits of improved relining performance as a defence against the Global Economic Crisis. Five of the six RUSSELL TWIN 8 Mill Relining Systems, ordered to date, are either operating or being manufactured for South American mine sites. The sixth is for Sino IronÆs Cape Preston Project in Western Australia. This paradigm shift, towards very short relining times, aims at displacing mill relining activities from the critical path of concentrator maintenance shutdown schedules. The first uses of the RUSSELL TWIN 8 Mill Relining System have seen some of the highest semi-autogenous grinding (SAG) mill new liner placement rates ever observed by Russell Mineral Equipment (RME), as would be expected with two, independent Machines working simultaneously in the one mill. The liner replacement rate, averaged over the whole reline is good (27 per cent improvement over single Machine System in the same mill) but short of full potential. This modest result can be attributed to reline crews unfamiliarity with RUSSELL TWIN 8 System operation. This paper compares a sample of conventional (single machine) RME Mill Relining System performance data with one ædouble headÆ mill liner handler by others. Early performance of EscondidaÆs new RUSSELL TWIN 8 System performance is then compared with recent single machine data from Escondida, immediately prior to RUSSELL TWIN 8 commissioning. RME and Escondida look to constantly improving RUSSELL TWIN 8 System performance as full operational familiarity is achieved. The preparation of this paper revealed a need to develop a global industry standard for mill relining data collection. A web based platform to develop data collection templates is also discussed in Appendix 1.

Jan 1, 2009

By D H. Bell

Slab-buckle failures in coal sequences involve thin slab deformation in strata dipping parallel to the footwall, and are a consequence of both unloading and the weak nature of the thinly bedded rock mass. Methods of modelling and predicting such occurrences include: +        a conceptual model using a base friction table, +        a mathematical model using the Euler solution for column and beam bending (after Goodman, 1980), and +        computer analysis techniques such as UDEC (Universal Distinct Element Code after Cundall and Hart, 1993).   Slab-buckle failures have the potential to seriously disrupt production because of their volume and rapidity, and to endanger both equipment and personnel working on the pit floor.   In July 2004 a large slab-buckle failure occurred overnight after a new batter and bench had been formed at the Malvern Hills Opencast Mine in inland Canterbury. This involved the entire length of the pit (85m along strike) when a 2m thick intact slab with a total volume of ~3500m3 translated down dip 6.2m on the base of a thin coal seam to form a pronounced buckle at the toe. The coal measures consist of finely laminated mudrocks with multiple coal seams of varying thickness dipping ~45¦ to the southeast, and the opencast mine had been designed with footwall batters formed parallel to bedding with a vertical bench separation of 15m.   Back analysis of the Malvern Hills failure was necessary to investigate the controls on footwall instability, and for future mine design. An engineering geological model was created and samples of the slab material and failure surface were collected and tested to establish the required parameters for use in the Euler solution for column and beam bending. Back analysis using the Euler solution provided unrealistic results that overestimated the overall length of a stable slope by more than 10 times.   No further large scale slab-buckle failures have developed at the mine site, in part because of the slow rate of coal extraction, but precautionary drainage of the footwall slopes has been undertaken to improve overall batter stability. The location of the slab-buckle failure on a critically positioned pre-sheared thin coal seam with full hydrostatic head is considered the most probable cause of the July 2004 failure, rather than inherent instability of the generic bench and batter arrangement adopted. The use of a precedent-based engineering geology approach to future mine design is considered the most appropriate solution in the circumstances.

Jan 1, 2007

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013